D+LED-LP5RGB _____________________________________________________ D+LED-LP5RGB Descriptions: 5mm roundHeight 2.5mm, 6-pin Flux LEDwhite diffused lens Features: Flux LED Type Sizemm:5*8.4*7.62 Emitting Color: Red-Green-Blue Wide view angle at 110 Pb-free wave soldering application RoHS Compliant Patented product Applications: Decorative lighting Indicators Illuminations Automotive application CUSTOMER APPROVED APPROVED BYCHECKED BYPREPARED BY

D+LED-LP5RGB _______________________ Absolute Maximum Ratings (Ta = 25 )ItemsSymbolAbsolute maximum RatingUnit Forward Current(DC)IF R:50 G/B:30 mA Peak Forward Current*IFP100mA Power DissipationPD120mW Operation TemperatureTopr-40 ~ +95 Storage TemperatureTstg-40 ~ +100 Reverse VoltageVR5V Soldering TemperatureTsol Reflow Soldering:260/2sec Hand Soldering: 300/2sec *Pulse width1msec duty 1/10 Typical Electrical & Optical Characteristics ( Ta = 25) ItemsSymbolConditionMin.Typ.Max.Unit Forward VoltageVFIF = 20mA R1.7 G2.8 B2.8 --- R2.6 G3.6 B3.6 V Reverse CurrentIRVR = 5V5uA Dominant WavelengthDIF = 20mA R621 G525 B465 --- R626 G530 B470 nm Luminous FluxVIF = 20mA R2.5 G4.5 B1.3 lm Luminous IntensityIVIF = 20mA--- R:700 G:1500 B:350 ---mcd 50% Power Angle2IF = 20mA---110---Deg Material ItemReflectorWireEncapsulateChip MaterialCopperGoldEpoxyAlGaInP/InGaN

R: 2.1G: 3,1B:3,1D+LED-LP5RGB _______________________ Package Dimensions (unit: mm 456321C1.5BJ TMMark6 5 4456321 Notes All dimensions are in mm. Tolerance is 0.25 mm unless otherwise noted. An epoxy meniscus may extend about 1.5 mm down the leads. Burr around bottom of epoxy may be 0.5 mm max.

D+LED-LP5RGB _______________________ Typical Electrical/Optical Characteristics Curves(Ta=25Unless Otherwise Noted) Ta(C)Fig. 5 Relative Luminous Fluxvs Ambient TemperatureFig. 2 Relative Luminous Intensity vs Forward CurrentFig. 6 Relative Luminous Fluxvs Radiation AngleFig. 4 Relative Luminous Flux vs Wavelength100%0400 450 500 550 600 650IV 100%WL(nm)80%60%40%20%700100%-30 -10 10 30 50 7050%20%10%200%REDIV 100%If(mA)0 10 20 30 40 502.01.001.50.52.5BLUEIf(mA)Ta(C)Vf(v)1.60Fig. 1 Forward Current vs Forward VoltageIf(mA)2.0 2.4 2.8 3.2 3.61020304050Fig. 3 Maximum Forward Current vs Ambient Temperature100 80 60 40 20 0100806040200RED BLUEREDGREEN/BLUEBLUEREDGREENREDGREENBLUEGREENGREEN8090706050403020109080706050403020100100% 75% 50% 25% 100% 75% 50% 25% 0

D+LED-LP5RGB _______________________ Precautions for use: 1.Storage Any mechanical force or any excess vibration shall not be accepted to apply during cooling process to normal temperature after soldering Avoid quick cooling Leadframesaresilverplatedcopperalloy.Thesilverplatesurfacemaybeaffectedby environments which contains corrosive substances. Please avoid conditions which may cause the LEDs to corrode,tarnish or discolour 2.Soldering Manual SolderingSolder Dipping Soldering Iron35W max.Preheat110max Temperature280max(63/37 Solder)Preheat time60 seconds max. 300max(Pb free solder)Solder temperature63/37 Solder:235(245max) Soldering Time3 seconds max.Pb-freesolder:255 (260 max) PositionNotlessthan3mmfrom the base of the epoxy Dipping Time3 seconds max. PositionNotlessthan3mmfromthe base of the epoxy Recommended soldering profile: Times(Sec)5010015020025030000 10 20 30 40 50 60 70 80 90 100 110 120Temperature( )Preheatlaminar wave Solder=Sn 63-Pb 37Solder= Pb-Free Peak preheat temperature:100-110Peak preheat temperature:100-110 Total preheat time:50-60secondsTotal preheat time:50-60seconds Peak profile fit temperature:235(max 245)Peak profile fit temperature:260max Dwelltimeabove200shouldnotexceed3 seconds Dwelltimeabove200shouldnotexceed3 seconds

D+LED-LP5RGB _______________________ Caution The LEDs must not be repositioned after soldering Do not apply any stress to the lead particularly when heat 3. Static Electricity Static Electricity and surge voltage damage the LEDs. So it is recommended that an ESD wrist band, ESD shoe strap or an anti-electrostatic glove be used when handling the LEDs. All devices, equipment and machinery must be properly grounded 4.Others Reverse voltage should not exceed the absolute maximum rating on the data sheet. TheLEDleadsmaybecometarnishediftheycontacthydrogensulphideorothergaseous chemicals. The colour of the LEDs is changed slightly an operating current and thermal. This device should not be used in any type of fluid such as water, oil, organic solvent and etc When washing is required, IPA (Isopropyl Alcohol) should be used. The influence of ultrasonic cleaning on the leds depends on factors such as ultrasonic power and the way. Galliumarsenideisusedinsomeoftheproductslistedinthispublication.Theseproductsare dangerous if they are burned or smashed in the process of disposal, It is also dangerous to drink the liquid or inhale the gas generated by such products when chemically disposed. High-brightness LED light may injure human eyes. Avoid looking directly into lighted LED The appearance and specifications of the product may be modified for improvement without notice.