lp7000 spec
TRANSCRIPT
-
7/30/2019 LP7000 Spec
1/16
LP7000
Specifications
-
7/30/2019 LP7000 Spec
2/16
-
7/30/2019 LP7000 Spec
3/16
1
Specifications
System
Printer processor section
Overall dimensions See Dimensions.
Processing speed 1638 mm/minute
Heating capacity About 0.453 kW (about 390 kcal/h)
Weight Approx. 301.73 Kg
Exposure conditions Controlled with the built-in colorimeter.
Operati
on
section
Display module
Exposure engine iBeam Engine
The flatbed scanner recommended by us*1, which is used at iBeam Engine
setup, is necessary.
To know more about the flatbed scanner, please consult your technical
representative.
*1. For the suitable flatbed scanner models, see Flatbed scanner
(recommended) as explained later.
Print resolution
Main scanning:Sub-scanning: 300 dpi300 dpi
Exposure speed 27.94 mm/second
Exposure system Exposure scanning via paper advance
Print size
Paper width: 89, 102, 114, 117, 120, 127, 130, 152, 165, 178, and 203 (mm)
Paper advance length: from 82.5 to 610.0 mm
Paper supply Single magazine type (Dual magazine type and triple magazine type are
factory options.)
Paper specification Maximum diameter of paper roll: 250 mm
Transport system Roller transport system
Temperature control Temperature in each sub-tank is controlled separately.
Replenishment system The system calculates the processed amount of paper surface based on the
print size and automatically supplies the appropriate amount of replenisher
to each tank.
Water refilling Water refilling is performed automatically when the solution level sensors
are activated.
Automatic cleaning The upper guides are automatically cleaned at close down checks.
-
7/30/2019 LP7000 Spec
4/16
2
External interface
Processing tank capacity Color Developer
8.5 liters
Bleach Fixer
8.2 liters
Stabilizer
11.6 liters
Processing time Color Developer
22.3 sec (31.1 sec)*1
Bleach Fixer
27.1 sec (37.8 sec)*1
Stabilizer
43.1 sec (60.1 sec)*1
Dryer
14.5 sec (20.2 sec)*1
*1. Processing time required for some types of paper
Processing temperature Color Developer
420.3C
Bleach Fixer402.0C
Stabilizer
38 - 42C
Replenishment solution tank capacity Color Developer
6.6 liters
Bleach Fixer
6.0 liters
Stabilizer
17.1 liters
Effluent tank capacity Color Developer
4.0 liters Bleach Fixer
4.1 liters
Stabilizer
5.8 liters
Collection of effluents Two effluents are separately collected by natural dripping.
Dryer Hot air ink drying method
Energy-saving type using automatic power control
Order classification Max. three orders (Varies depending on the paper size.)*1
*1. Maximum 12 orders when print sorter unit type 1 (option) is installed.
Maximum 10 orders when print sorter unit type 2 (option) is installed.
Ethernet (100Base-TX) 1 port
Display module interface 1 port
External AC power outlet Outlet type 3 output
Power supply voltage 200 V to 240 V (conform to the power supply specification)
Power capacity 3A
-
7/30/2019 LP7000 Spec
5/16
3
Flatbed scanner (recommended products)
Actual tank capacities may differ slightly from the volumes shown above.
Depending on the combination of paper and processing solution, maximum density of print may be different.
For details, contact your place of purchase.
Manufacturer Product name
EPSON A4 flatbed scanner
Perfection 4990 Photo
Perfection V700 Photo
Perfection V750
-
7/30/2019 LP7000 Spec
6/16
4
Processing capacity
Repeat processing capacity
*1. Calculated according to our criteria. The actual processing capacities may differ depending on various conditions.
Repeat processing capacity
The following is the processing capacity for some types of paper.
*1. Calculated according to our criteria. The actual processing capacities may differ depending on various conditions.
Print size (Paper width Paper advance length) Capacity (Prints/hour)*1
120 mm 82.5 mm 823
127 mm 89 mm 781
152 mm 102 mm 758
203 mm 102 mm 758
89 mm 127 mm 622
102 mm 152 mm 527
127 mm 178 mm 455
102 mm 203 mm 402
203 mm 254 mm 325
203 mm 305 mm 259
203 mm 610 mm 96
Print size (Paper width Paper advance length) Capacity (Prints/hour)*1
120 mm 82.5 mm 688
127 mm 89 mm 647
152 mm 102 mm 578
203 mm 102 mm 578
89 mm 127 mm 480102 mm 152 mm 410
127 mm 178 mm 356
102 mm 203 mm 316
203 mm 254 mm 258
203 mm 305 mm 217
203 mm 610 mm 85
-
7/30/2019 LP7000 Spec
7/16
5
Required space and dimensions
Space required for installation
! For single magazine type
*1. Extension table (option) not attached
*2. The required space is the same even if the print sorter unit (option) is installed.
*3. If there is additional space in the installation area, we recommend leaving a space of 205 mm or more between the back of system
and wall to facilitate maintenance operations.
! For dual magazine type/triple magazine type
*1. The required space is the same even if the print sorter unit (option) is installed.
*2. If there is additional space in the installation area, we recommend leaving a space of 205 mm or more between the back of system
and wall to facilitate maintenance operations.
1390ormore
*2
90ormore
3
250 or more
2100 or more350 or more*1
(Unit: mm)
Extension table (option)
G088213
Dual magazine unit (option) or triple magazine unit (option)
2390 or more
(Unit: mm)
250 or more
90ormore
*2
182 or more
1390ormore
*1
G088214
-
7/30/2019 LP7000 Spec
8/16
6
Dimensions
*1. When the print sorter unit (option) is installed
*2. When the processing rack is lifted
*3. When the table is raised to the top
640
526
(Unit: mm)
13
35
1957.8
1499.8
1
3902
Dual magazine unit (option) or triple magazine unit (option)
775(827*1)
70
0
1849.8
9551
155*3
G088215
-
7/30/2019 LP7000 Spec
9/16
7
Power capacity
The values shown here are for installing the power supply.
Supply voltage should be within 10% of the specified voltage.
The power capacity varies depending on the power supply specification.See the appropriate information for each specification.
The three-phase four-wire system is not used in the United States.
IMPORTANT
Use a grounding resistance of 100 or less when grounding this product.
For details about 1P2W, see1P2W.
For details about 3P3W, see3P3W.
For details about 3P4W, see3P4W.
"""" 1P2W
Wiring chart
*1. Supply voltage should be within 10% of the specified voltage.
*2. This is the capacity required for power supply installation.
*3. When installing the film processor, be sure to provide a separate circuit breaker from the printer processor.
NOTE
Leakage current value: 11.2 mA (reference value)
"""" 3P3W
Supply voltage*1 Power capacity*2
AC 200 V 3.6 kVA (18 A)
AC 208 V 3.8 kVA (18 A)
AC 220 V 3.7 kVA (17 A)
AC 230 V 3.8 kVA (17 A)
AC 240 V 4.0 kVA (17 A)
Supply voltage*1 Power capacity*2
AC 200 V 3.6 kVA (12 A)
AC 208 V 3.8 kVA (13 A)
AC 220 V 3.7 kVA (11 A)
AC 230 V 3.8 kVA (11 A)
AC 240 V 4.0 kVA (11 A)
*3
*3
(30 A)
Circuit breaker Main circuit breaker
Printer processor
Ground
1P2W
(AC 200 V-240 V)
Power supplyDistribution box
G075757
-
7/30/2019 LP7000 Spec
10/16
-
7/30/2019 LP7000 Spec
11/16
9
Standard equipment
Printer section
*1. The paper width can be selected from the following:
89, 102, 114, 117, 120, 127, 130, 152, 165, 178, and 203 (mm)
Paper processor section
Item StatusCastors Attached
Magazine*1 1
Table height adjust function Built-in
Correction value printing unit (CVP) Installed
Display module Installed
Item Status
Remote effluent tank Built-inEffluent level alarm (1 per tank) Built-in
Dryer overheat prevention system Built-in
Solution overheat prevention system Built-in
Processing tank level alarm Built-in
Circulation pump stop alarm Built-in
Dryer temperature setting function (for each paper magazine) Built-in
Drive and dryer automatic stop function Built-in
Castors Attached
Print conveyor unit Installed
Control strip holder 1
Surge absorber (surge protection circuit) Built-in
Automatic cleaning Built-in
Replenishment solution remaining amount alarm (1 per tank) Built-in
Automatic water refilling unit Built-in
Incorrect cartridge loading prevention function Built-in
Automatic solution mixing Built-in
-
7/30/2019 LP7000 Spec
12/16
10
Standard accessory
Printer processor section
Name Quantity RemarksC-ring #4 5 Accessory for processing rack
C-ring #6 5 Accessory for processing rack
Vinyl hose (inside diam. 9 mm outside diam. 13 mm length
1500 mm)
1 For treating effluent
Slow-blow fuse (3.15 A) 2 Spare item
Slow-blow fuse (6.3 A) 2 Spare item
Slow-blow fuse (10 A) 2 Spare item
Slow-blow fuse (5 A) 2 Spare item
Glass tube fuse (2 A) 2 Spare item
Check date entry sticker 1 Sticker to write the date that float switch
operation was checkedStick 1 For checking the operation of the float
switch in the processing tank
Cleaning sheet 1 Cloth for cleaning the colorimeter unit
Cleaning wiper 1 Cleaning supply
Lower turn belt 1 Accessory for processing rack
Lower turn belt (3) 1 Accessory for processing rack
Washing bottle (500 ml) 1 For cleaning processing rack
Measuring hose (1) 1 For Color Developer replenishment
solution, Bleach Fixer and Stabilizer
replenishment solution
Measuring hose (2) 1 For measuring replenishment solution
(PS1 and PS2)
Measuring hose (3) 1 For measuring replenishment solution
(PS3 and PS4)
Paper holder 1 For measuring test prints for iBeam
tuning
Plug code (1 m) 1 Power supply cable for PC
Plug code (2.5 m) 1 Power supply cable for monitor
LAN cable (0.7 m) 1 Cross type
Flat cable clamp 5
Anti-contamination cover (includes the maintenance cover) one each Prevents auxiliary solutions from
dripping into the CD solution when
removing processing racks, etc. (Themaintenance cover is for preventing
processing solution from adhering to the
processor loading unit.)
Chain Oil 1 Oil for lubricating the dryer drive chain
-
7/30/2019 LP7000 Spec
13/16
11
Options (Printer)
Some of the following options may not be available in some countries and areas.
For details, contact your place of purchase.
Printer section
Paper magazine
Option No. Name Explanation
Z804937-01 DP bag hanger (DH-6) Hanger for holding developed films and DP bags.
H086044-00 Ink ribbon cassette CVP ink ribbon
Z811139-01 Dual magazine unit Unit compatible with the dual magazine type
The paper magazine is required separately.
(available as factory option)
Z811140-01 Triple magazine unit Unit compatible with the triple magazine type
The paper magazine is required separately.
(available as factory option)
Z811135-01 Expansion table Mainly used to place the A4 flatbed scanner on.
Z810651-01 Counter unit Indicates the number of prints.
Z811137-01 Monitor table Table to place the display monitor on
Z811114-01 LCD monitor arm Monitor arm with which you can freely change direction
of the display.
Z811147-01 Rear cover The cover to hide the rear side of the machine.
Z811191-01 Storage cabinet When the table is raised, a cabinet can be installed under
the table.
I068490-00 Plug cord For connecting the scanner (1.5 m)
Option No. Name Explanation
Z811196-02 Paper magazine, 89 mm Include Magazine spindle unit 1 and handle.
Z811196-03 Paper magazine, 102 mm
Z811196-04 Paper magazine, 114 mm
Z811196-05 Paper magazine, 117 mm
Z811196-06 Paper magazine, 120 mm
Z811196-08 Paper magazine, 127 mm
Z811196-09 Paper magazine, 130 mm
Z811196-10 Paper magazine, 152 mm
Z811196-11 Paper magazine, 165 mm
Z811196-12 Paper magazine, 178 mm
Z811196-13 Paper magazine, 203 mm
-
7/30/2019 LP7000 Spec
14/16
12
Options (Paper processor)
Some of the following options may not be available in some countries and areas.
For details, contact your place of purchase.
Paper processor section
Option No. Name Explanation
C008075-01 Floor tray Placed underneath the system to prevent the floor from
becoming dirty.
B011625-01 Rack transportation tank Used to transport wet processing racks.
C101570-01 Turn rack vat Container for immersing the upper guide in water.
A202513-01 Filler 5-liter measuring pitcher
H049014-00 Effluent tank Collects effluent that overflows from the processing
tanks. (20 liters)
L005253-00 Measuring cylinder Used to measure replenishment solution, etc. (200 ml).
Z810657-01 Minute meter unit Displays the system operating time.Z811175-01 Sorter modification kit (10 orders) Modifies the print sorter unit to support 10 orders (only
when print sorter unit type 1 is installed)
H089016-00 Cleaning sheet Used to clean the pressure roller of the colorimeter unit.It
should be cleaned every six months. Three sheets
included.
Z811171-01 Print sorter unit (type 1) Allows prints to be sorted by order (12-order type).
Z811172-01 Print sorter unit (type 2) Allows prints to be sorted by order (10-order type).
Z811150-01 Control strip auto loading unit Unit to process the control strip without using the control
strip leader.
-
7/30/2019 LP7000 Spec
15/16
13
Commercially available items to be
prepared by the customer
The items below are required according to the installation environment of the customers.
They should be prepared by customers if necessary.
Item Remarks
HUB When several systems are connected to the PC, a hub is
necessary. (Should be with the required number of 100BASE-TX
ports.)
LAN cable Cross type The cable of 0.7 m is supplied as a standard accessory. If the
longer cable is required, prepare the longer cable.
Straight type Prepare this when connecting the system using a HUB.
-
7/30/2019 LP7000 Spec
16/16
14
Installation requirements
This system is to be used in a location with a relative humidity from 30 to 75% and temperature from 15 to 30C (59 to
86F).
The light source for this system should be a natural light color, and the light intensity should be between 300 and 400 lux.
If there are lights near to the system, they must be screened. In particular, if the product is installed near a window, use
curtains or blinds to block direct sunlight from the product.
Do not install the product in a place where the operator is exposed to direct sunlight. Make sure the display monitor is
located away from direct sunlight or other bright light sources.
Avoid installing the product in areas with high dust levels or subject to vibration.
Do not raise or lower the room temperature quickly. Raising the temperature quickly can cause condensation inside the
system, which leads to problems such as lens fogging, paper jam, and malfunctions in the electronics and PCBs.
Because the system uses liquids during normal operation, please make sure that the floor and walls are waterproof for
safety reasons. In addition, we recommend installing a sink or drain in the room to facilitate washing racks.
Castors are for moving the system. Once the system has been installed, be sure to fix it in place with the adjusters or jack
bolts.
If the level difference of the floor on which the system is installed (the height difference between jack bolts) is 10 mm or
more, a plate or shim should be used to adjust the level.
Use this system in a DC magnetic field (earth magnetic field, etc.) of 0.6G*1or less and AC magnetic field (power source
magnetic field, etc.) of 0.06G*1 (rms) or less.
*1. 0.6G = 60T, 0.06G = 6T
The system is programmed with default values prior to shipment. These values may differ depending on the environment
and operating conditions. Change them as necessary.
The maximum permissible system impedance Zmax of this system is 0.063+j0.039, supplied from a power distribution
system having a rated voltage of 400/230 V. This system is connected only to a supply of that impedance or less.
Determine the connection to a power supply in consultation with the supply power company.
This equipment complies with EN61000-3-12.
Subject to change without notice.