nissin sapphire touchscreen equipment kr en siwoo ag 11 sep 14
TRANSCRIPT
사파이어 터치스크린 스쾌어
Sapphire Touchscreen Squarer NWSS-500D
설비기능: 해당 설비는 다이아몬드와이어를 이용해 선망을 만들어 쾌속이동을
진행하여 원통형의 반제품재료를 여러덩이의 직사각형 혹은 방형 절단면의 컬럼으로 절단하는것이다.
Equipment function: This equipment uses diamond wire to build a fast moving wire net, to cut cylindrical sapphire boule into cuboid blocks.
가공대상: 사파이어、결정실리콘、경성재료、석영. Workpiece type: Sapphire, polycrystalline silicon, hard material, quartz, etc.
부속품Workpiece 최대부속품직경 Max workpiece diameter φ500mm (20”) 최대부속품높이 Max workpiece height 500mm 최소완성품너비 Min product width 34mm×34mm
절단 Cutting 다이아몬드와이어지름 Diamond wire diameter (with coating) φ0.25~0.42mm 다이아몬드운동속도 Diamond wire moving speed Max 720m/min
절단속도 Cutting speed 0~1mm/min 절단승강거리 Horizontal feeding travel Max 600mm 쾌속승강속도 Horizontal feeding speed 0~500mm/min 와이어장력 Wire tension 0~100N
와이어장력제어방식 Control method of wire tension Air cylinder 절단스윙각도 Cutting swing angle ±5° 다이아몬드길이 Diamond wire length 12km 절단구역너비 Cutting area width 400~560mm
절단프레임이동거리 Cutting frame feeding travel Max 160mm 절단프레임이동방식 Feeding method of cutting frame Air cylinder
Siwoo Trading Co., Ltd. www.siwoo.co.kr Tel: 82-2-2042-7773 Fax: 82-2-3431-4421
작업대 Worktable
작업대결정체방향조정너비 Amplitude accommodation of crystal
angel in worktable ±5°
작업대이동거리 Worktable move distance Max 65mm 작업대이동방식 Worktable move method Handwheel
절단액 Coolant 절단액공급량 Coolant supply (cycling) 80L/min 절단액탱크용량 Coolant tank volume 100L 절단액온도 Coolant temperature 5~6℃
냉각수 Cooling water 냉각수유량 Cooling water flow ≈2m³/h 냉각수공급온도 Cooling water temperature 8℃~12℃ 냉각수이음매형태 Cooling water outlet type φ24mm, soft tube+hoop
에어서플라이 Compressed air 에어압력 Compressed air pressure 0.5~0.6MPa 에어유량 Compressed air flow 30m³/h
에어이음매칫수 Compressed air outlet size φ16mm pressure pipe 모타 Motor
컷팅가이드휠서브모타 Cutting guide wheel servo motor 4.9kW×2pcs 컷팅승강서브모타 Horizontal feeding servo motor 0.84kW 컷팅스윙서브모타 Cutting swing servo motor 0.84kW 코일링서브모타 Coiling servo motor 5.2kW×2pcs 와인딩서브모타 Winding servo motor 0.82kW×2pcs 작업대서브모타 Worktable servo motor 0.82kW×2pcs 펌프모타 Pump motor 0.45kW
전기전력공급빈도 Electric supply frequency 50Hz 모타총출력 Total power for all motors ≈23kW
설비 Machine 인터피스 Interface Touch screen 주엔진외형 Machine size 2855L×1655W×2635H mm 기계중량 Weight ≈9000kg
Siwoo Trading Co., Ltd. www.siwoo.co.kr Tel: 82-2-2042-7773 Fax: 82-2-3431-4421
사파이어 터치스크린 절단기
Sapphire Touchscreen Cropper NWD-500
부속품Workpiece
최대부속품직경 Max workpiece diameter φ500mm (20”) 최대부속품높이 Max workpiece height 500mm
절단 Cutting 다이아몬드와이어지름 Diamond wire diameter (with coating) φ0.25mm~φ0.42mm 다이아몬드와이어운동속도 Diamond wire moving speed Max 720m/min
절단속도 Cutting speed 0~1mm/min 절단승강거리 Horizontal feeding travel Max 600mm 쾌속승강속도 Horizontal feeding speed 0~200mm/min 선장력 Wire tension 0~100N
절단스윙각도 Cutting swing angle ±3° 작업대 Worktable
작업대결정체방향조정너비 Amplitude accommodation of crystal angel in
worktable ±5°
작업대전후이동속도 Worktable forward moving speed 500mm/min 작업대회전웜기어속도비율 Worktable rotating worm gear speed ratio 1:90
절단액 Coolant 절단액공급량 Coolant supply (cycling) ≈20L/min 절단액탱크용량 Coolant tank volume ≈100L
에어서플라이 Compressed air 에어압력 Compressed air pressure 0.6~0.7MPa 에어유량 Compressed air flow ≈10m³/h
에어이음매칫수 Compressed air outlet size φ10mm
Siwoo Trading Co., Ltd. www.siwoo.co.kr Tel: 82-2-2042-7773 Fax: 82-2-3431-4421
모타 Motor 코일링서브모타 Coiling servo motor 2kW×2pcs 컷팅승강서브모타 Horizontal feeding servo motor 0.4kW 컷팅스윙서브모타 Cutting swing servo motor 0.2kW 와인딩속도조절모타 Winding speed governing motor 0.1kW×2pcs 작업대전후이동모타 Worktable forward moving deceleration motor 90W 작업대전후이동감속비율 Worktable forward moving deceleration ratio 1:30
펌프모타 Pump motor 0.45kW 전기전력공급빈도 Electric supply frequency 50Hz 모타총출력 Total power for all motors ≈5.3kW
설비 Machine 인터피스 Interface Touch screen 주엔진외형 Machine size 1350L×1100W×2600H mm 물탱크외형 Water tank size 500L×750W×300H mm 기계중량 Weight ≈2000kg
Siwoo Trading Co., Ltd. www.siwoo.co.kr Tel: 82-2-2042-7773 Fax: 82-2-3431-4421
사파이어 터치스크린 다이아몬드와이어 절편기 Sapphire Touchscreen Diamond Wire Saw
NWS-180.2
부속품Workpiece
최대부속품직경 Max workpiece diameter φ150mm (6”) 최대부속품길이 Max workpiece length 300mm 최대부속품수량 Max workpiece number 2pcs
컷팅롤러 Cutting roller 재질 Material Polyurethane rubber
최대절단롤러직경 Max Cutting roller diameter φ180mm 최대절단롤러길이 Max Cutting roller length 300mm 최대절단롤러수량 Max Cutting roller number 3pcs 롤러중심거리 Roller center distance 400mm 최대회전속도 Max rotational speed 2300rpm
다이아몬드와이어 Diamond wire 다이아몬드와이어지름 Diamond wire diameter (with coating) φ0.25mm 다이아몬드와이어길이 Diamond wire length 50km 다이아몬드와이어운동속도 Diamond wire moving speed Max 900m/min
스윙운동 Swing motion 전체스윙각도 General swing angle 0~±8°
φ150mm부속품스윙각도 Swing angle for φ150mm workpiece <±6° 스윙속도 Swing speed 0~500°/min
이송컷팅운동 Feeding and cutting motion 부속품이송거리 Workpiece feeding distance Max 215mm 이송속도범위 Feeding speed range 0~375mm/min
아크스윙테이블조정 Arc swing table adjustment 8° 회전대조정 Rotary table adjustment 3° 선장력 Wire tension 35~45N
Siwoo Trading Co., Ltd. www.siwoo.co.kr Tel: 82-2-2042-7773 Fax: 82-2-3431-4421
에어서플라이 Compressed air
에어압력 Compressed air pressure 0.4~0.7MPa 에어유량 Compressed air flow 24m³/h
냉각수 Cooling water 냉각매체 Cooling medium Coolant 물탱크용량 Water tank volume 324L 냉각수유량 Cooling water flow 320L/min 온도제어 Control temperature ±2°
냉각수이음매형태 Cooling water outlet type G1/2 환경요구 Environment requirement
환경온도 Environment temperature ≤15℃~25℃ 절단과정중 온도파동 Temperature fluctuation during cutting ≤2℃
온도변화 Temperature change <0.5℃/h 상대온도 Relative humility 50%±10%
모타 Motor 3롤러컷팅서브모타 Three roller cutting servo motor 22.5kW, 2300rpm 3롤러스윙서브모타 Three roller swing servo motor 3.3kW, 3000rpm 부속품이송서브모타 Workpiece feeding servo motor 2.3kW, 3000rpm×2pcs 코일링서브모타 Coiling servo motor 9.3kW, 3300rpm×2pcs 와인딩서브모타 Winding servo motor 0.82kW, 3000rpm×2pcs 장력서브모타 Tension servo motor 5.2kW, 2000rpm×2pcs 펌프모타 Pump motor 0.75kW 원심펌프모타 Centrifugal pump motor 1.1kW 기름안개정화기 Oil mist purifier motor 0.75kW
전기박스에어컨디셔너 Electric box air-conditioner motor 1.5kW×2pc 모타총출력 Total power for all motors ≈70kW
설비 Machine 주엔진외형 Machine size 2965L×2420W×2290H mm 터치스크린 Touch screen rotation radius 1150mm 기계중량 Weight ≈14T
Siwoo Trading Co., Ltd. www.siwoo.co.kr Tel: 82-2-2042-7773 Fax: 82-2-3431-4421
사파이어 터치스크린 복합가공기 Sapphire Touchscreen Composite Processor
NVG-432-G
해당 설비는 전문 핸드폰패널의 복합가공을 위해 설계한것이다. This equipment is specially designed to process mobile sapphire touchscreen. 채용한 2축3스테이션설계는 동시에 혹은 각자로 핸드폰패널의 윤곽과 구멍을 뚫는 작업을 진행할수 있으며
정밀 그라인딩과 거친 그라인딩의 동시적인 가공을 실현할수 있어 작업효율을 대대적으로 제고할수 있다. It adopts the design of two axes and three stations, to contour and punch the sapphire
plate simultaneously or separately. Fine grinding and coarse grinding can also be worked out at the same time. This efficient process mothed can considerably increase the throughput.
파나소닉CCD 공업용카메라의 정확한 위치측정은 가공의 정밀도에서 아주 좋은 효과에 도달한다. Precise positioning of Panasonic CCD camera has satisfactory result for process
precision. 가공정밀도 Machining precision
X/Y/Z축 운동위치측정정밀도 X/Y/Z axis positioning precision ±0.008mm X/Y/Z축 운동중복정밀도 X/Y/Z axis motion repeatability ≤0.005mm
X/Y/Z축 마그네틱테이블행정 X/Y/Z axis travel for magnetic table 208X×130Y×95Z mm X/Y/Z축무마그네틱테이블행정 X/Y/Z axis travel without magnetic table 208X×160Y×95Z mm
최대부속품칫수 Max workpiece diameter 200X×120Y×10Z mm 작업대칫수 Worktable size φ600mm
작업대회전정밀도 Worktable rotating precision ±5’ 작업대회전주기 Worktable rotating period 6s 가공부속품정밀도 Workpiece machining precision ±0.015mm
아이들러닝쾌속이동속도 Rapid speed for free travel 6m/min 베컴석션테이블 Vacuum suction worktable
칫수 Size 138L×64W×25H mm 흡인력 Suction 30kg/cm
Siwoo Trading Co., Ltd. www.siwoo.co.kr Tel: 82-2-2042-7773 Fax: 82-2-3431-4421
마그네틱테이블 Magnetic table 옵션수량 Optional number 3pcs 칫수 Size 150L×175W×60H mm 흡인력 Suction 14kg/cm
전기스핀들 Electric spindle 스핀들모델 Spindle type DGZ-60F1 최고빈도 Max frequency 1000Hz 최고회전속도 Max rotational speed 60000rpm 최고전압 Max voltage 200V 정격전류 Rated current 4.0A 최대출력 Max power 1.2kW 최대토크 Max torque 0.19N·m 최대전류 Max current 6.0A
코니컬서피스동심도 Conical surface run-out ≤1.0 나이프아울렛 Knife outlet ER11 (DIN6499)
지그토크(φ6”힐트) Clamp torque (φ6” hilt) ≥254N·m 샤프트 앤드 스윙 Shaft end swing ≤3μm
진동치(홀더및록너트 불포함) Vibration value (not including holder/lock nut) ≤0.6mm/s 조립면직경 assembly surface diameter φ61.902~61.91mm
냉각시스템물흐름량 Cooling system water flow at 0.2~0.4MPa ≥1.6L/min 스핀들소음치 Spindle noise value ≤70dBA
스핀들다스트개스유량 Spindle blowing dust gas flow at 0.1~0.15MPa ≥30L/min 모타권선절연저항 Insulation resistance of motor winding ≥500MΩ
전기스핀들권선내압시험 Electric spindle winding voltage withstand test 1500 V/1 minute 퓨즈보호전류 Current fuse protection 32A
에어서플라이 Compressed air 에어압력 Compressed air pressure ≤0.75MPa 에어유량 Compressed air flow 100L/min
冷却水 냉각수 Cooling water 물탱크용량 Water tank volume 180L 냉각수유량 Cooling water flow 200L/min
모타 Motor 축방향이동모타 Axial moving motor 1000W×6pcs 냉각수펌프 Cooling water pump 450W 필터펌프 Filter pump 120W
전기스핀들쿨링펌프 Electric spindle cooling pump 250W 물순환진공펌프 Water circulation vacuum pump 1450W
전기스핀들 및 컨버터 Electric spindle and frequency converter 3700W×2pc 변압기 Transformer 4000W
모타총출력 Total power for all motors ≈20kW 설비 Machine
주엔진외형 Machine size 2430L×1560W×1670H mm 기계중량 Weight 2.2T
Siwoo Trading Co., Ltd. www.siwoo.co.kr Tel: 82-2-2042-7773 Fax: 82-2-3431-4421
사파이어 터치스크린 제분기 Sapphire Touchscreen Surface Grinder
NSH-450
NSH-450제분기는 고효율 및 고정밀도로 평면을 연삭하는 선반이다. Surface grinder NSH-450 is a highly efficient and highly accurate machine tool for
parallel surface grinding. 부속품의 두개 평면은 고정밀도의 평형도와 평면도 및 표면의 조도를 얻을수 있다. The two surfaces of workpiece will reach high degree of parallelism, flatness and
roughness. 선반조작시스템응용터치스크린 및 PLC자동제어시스템은 가공과정의 자동화를
실현할수 있다. The operation system of surface grinder uses touchscreen and PLC automatic control
system, to realize reliability and automation for the processing. 조작이 편리하고 조절이 원할하며 데이타가 직관적으로 보이게 하는등 장점이 있다. This equipment also features simplicity of operation, flexibility of adjustment, and
intuitiveness of data illustration.
부속품Workpiece 원형부속품칫수 Round workpiece size φ5~150mm 타원형 혹은 장방형
부속품칫수 Ellipse or rectangular workpiece size 5~180mm
부속품두께 Workpiece thickness 1~50mm 연삭기 Grinding wheel
砂轮外径연삭기외경 Outer diameter of grinding wheel φ450 연삭기내경 Inner diameter of grinding wheel φ150 연삭기회전속도 Rotational speed of grinding wheel 57~134rpm 아퍼그라인딩휠 승강속도
Horizontal speed of upper grinding wheel 0~1.3m/min
Siwoo Trading Co., Ltd. www.siwoo.co.kr Tel: 82-2-2042-7773 Fax: 82-2-3431-4421
맷돌 Grinding disc 맷돌이송행정 Feeding travel of grinding disc 5mm 맷돌이송빈도 Feeding frequency of grinding disc 127~296rpm 맷돌회전빈도 Rotation frequency of grinding disc 0~90rpm 캐리어속도 Carrier speed 8rpm
모타 Motor 아퍼그라인딩휠승강 (컨버션/브레이크)
Horizontal feeding of upper grinding wheel (Frequency conversion/with brake)
1.5kW, 4P
상하메인그라인딩(컨버선) Upper and lower main grinding disc
(Frequency conversion) 2.2kW, 4P×2pcs
캐리어전동(브레이크 포함)
Carrier transmission (With brake) 0.2kW, 4P
상부그라인딩윤활 Lubricating for upper grinding disc 0.075kW 하부그라인딩윤활 Lubricating for lower grinding disc 0.075kW
에어사양 Configuration for compressed air 0.5MPa 표준공구 Standard tool
표준공구 Standard tool 1 group 유성 기어 대해 부품 소재 이빨 모양
Toothed blank of planetary gear for holding workpiece
4 pcs of 1 group
설비 Machine 주엔진외형 Machine size 1810L×1050W×2470H mm 기계중량 Weight 3200kg
Siwoo Trading Co., Ltd. www.siwoo.co.kr Tel: 82-2-2042-7773 Fax: 82-2-3431-4421
사파이어 터치스크린 광택기 Sapphire Touchscreen Surface Polisher
NK-22B-L/P
해당 설비는 부속품의 2개 평면에 대해 정밀가공 혹은 광택내기를 진행할수 있으며 선택가능한 가압방식은
실린더방식 혹은 지레방식이 있다. This equipment can work on the two surfaces of workpiece for fine grinding or polishing.
Optional pressurizing methods includes double cylinder method and lever method. 실린더벙식: 상부맷돌의 승강과 가압은 2개의 실린더로 제어한다. Cylinder method: The horizontal feeding travel and pressurizing of upper cylinder are
controlled by 2 separate cylinders. 실린더방식으로 이용한 가압실린더는 안정형실린더이며 조작이 안정적이고 믿음성이 있다. 실린더공급업체는
일반적으로 SMC 혹은 고객이 지정한다. Cylinder method adopts stable type cylinder as pressurizing cylinder. Its operation is
easy. The cylinder supplier can be SMC or other company upon the assignment of the client.
지레형: 상부맷돌의 승강은 실린더 혹은 승강 리드스크류로 제어하며 가압은 지레로 제어한다. Lever method: The horizontal feeding travel of upper cylinder is controlled by a cylinder
or a lead screw, while its pressuring is controlled by a lever. 세이드로드가압은 감속모타제어 클럼프웨이트이동으로 압을 가하며 프레셔센서가 있으며 클러우즈 루프
컨트롤을 형성한다. 사용자는 터치스크린을 통해 가압정보를 받을수 있으며 제어가 편리하고 정확하다. The pressuring of lever method is realized by moving heavy block under control by
decelerating motor. Pulling pressure sensor helps this process to be close-loop control. Touch screen helps the pressuring, to accurately and conveniently control the process.
Siwoo Trading Co., Ltd. www.siwoo.co.kr Tel: 82-2-2042-7773 Fax: 82-2-3431-4421
부속품Workpiece
최대부속품직경 Max workpiece diameter φ470mm
최소부속품두께 Min workpiece thickness 0.5mm
상부맷돌 Upper grinding disc
상부맷돌칫수 및 재로
(주문하여 만둘수 있음)
Size and material of upper grinding disc
(customizable)
Fine grinding: φ1458×φ498×50 mm, nodular cast iron
Polishing: φ1458×φ468×70, marble
or φ1462×φ494×50, copper disc
상부맷돌회전속도 Rotation speed of upper grinding disc 3~15rpm
상부멧돌승강거리 Horizontal feeding travel of upper grinding disc Cylinder method: 475mm, 125mm for pressuring cylinder
Lever method: 365mm with 15mm for pressuring lever
상부맷돌하강방지장치 Anti-dropping device of upper grinding disc Cylinder method: Safety clasp driven by thin cylinder
Lever method: Lead screw self-lock
하부맷돌 Lower grinding disc
하부맷돌칫수 및 재로
(주문하여 만둘수 있음)
Size and material of lower grinding disc
(customizable)
Fine grinding: φ1458×φ498×50 mm, nodular cast iron
Polishing: φ1458×φ468×70, marble
or φ1462×φ494×50, copper disc
하부맷돌회전속도 Rotation speed of lower grinding disc 9~45rpm
하부멧돌승강거리 Horizontal feeding travel of lower grinding disc 40mm
기타기계 Other mechanical
가압범위 Pressuring range Cylinder method: 0~weight of upper grinding disc
Lever method: 50~500kg
중심기어회전속도 및 기어수량 Rotation speed and teeth No. of central gear 2~27.5rpm, PCD426, Z=142
큰기어회전속도 및 기어수량 Rotation speed and teeth No. of big gear ring 2~22.5rpm, PCD1530, Z=510
연마액공급홀수 Coolant supply hole number 48pcs
에어압력 Compressed air pressure 0.4~0.6MPa
모타 Motor
상부맷돌모타 Upper grinding disc motor 15kW, 4P
하부멧돌모타 Lower grinding disc motor 18.5kW, 4P
중심기어모타 Central gear motor 4kW, 4P
큰기어링모타 Big gear ring motor 7.5kW, 4P
하부맷돌승강모타 Lower grinding disc horizontal feeding motor 0.75kW, 4P
모타무게 Weighting motor 90W, 1:500
교반모타 Mixing motor 1.5kW, 4P
슬러리펌프 Slurry pump 0.75kW, 2P
모타총출력 Total power for all motors ≈48kW
전원 Electric power 380V, 50Hz, three phase
조작회로 Operation circuit 220V, 50Hz
설비 Machine
주엔진외형 Machine size 2795L×2160W×3150H mm
기계중량 Weight ≈12000kg
교반베럴칫수 Mixing barrel size φ805×870 mm
Siwoo Trading Co., Ltd. www.siwoo.co.kr Tel: 82-2-2042-7773 Fax: 82-2-3431-4421