nmf swivel joints iv speziale oplossingen voor types cf-tw ......for media like water, air, vacuum,...
TRANSCRIPT
Speziale oplossingen voor bijzondere uitdagingen Speziale oplossingen voor bijzondere uitdagingen Speziale oplossingen voor bijzondere uitdagingen
NMF Swivel Joints IV Types CF-TW, CF, HT & SO
Special solutions for
exceptional challenges
Copyright © 2013 NMF Techniek BV, Westerbroek The information in this catalogue is based on our considerable experience with the described products. There are many factors that influence the products’ functionality, among them the installation method and the way the installation operates. Therefore, general assumptions can change during usage. It is essential for the client to check the applicability of the individual products by testing them thoroughly. For these reasons and because of the wide scope of application of our products can NMF Techniek BV take no responsibility in individual cases regarding the accuracy of our recommendations. For specific applications, it is important to contact us. This catalogue has been compiled with the greatest care. However, it is possible that the information you find here is incomplete or incorrect. If this is the case, then please contact us by phone: +31 (0) 50 527 57 77, fax: +31 (0) 50 527 59 05, or e-mail: [email protected].
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
Profitability in seals and swivel joints Due to the combining sealing systems, as well as 25 years of experience, NMF is in a position to offer the proper solution to solve sealing issues and to reduce the cost-of-ownership and downtime for its customers. Customised solutions is our daily job! Several product scan be supplied with certificates like the EC1935:2004, FDA compliance, TA-Luft, Fire-Safe, BAM, EN10204, etc. The frog is in our logo for a reason. When there is pollution, the frog is one of the first animals to suffer. With the frog we want to show we care for the environment and supply seals and swivels that do not leak during normal usage and are therefore environmental friendly and durable.
Lipseals in their most versatile form
� no “scoring” of the shaft! � pressure resistant to 8, 15 and even to 150 bar � rotational speed up to 40 m/s or 20.000 rpm � large variety in materials through modular form � very long life � when replacing run-in oilseals there is no need to
repair the shaft � low friction and therefore less wear
� lower power loss through less friction on the shaft
� easy to replace oilseals, stuffing box packing systems and mechanical seals
For prolonged life in pumps, mixers, gear boxes and many more applications
Mechanical seals for heavy duty
� pressure up to 8 bar and speed up to 8 m/sec � modular system for optimal adapting the seal to
the equipment � both positive transfer of torque and a large
depot for grease guaranty a long trouble free life � ready to fit cassette system, no adaption of the
installation necessary � with complete accessory and spare parts
program
For dynamic sealing of high-viscose, sticky and crust building media
Spring loaded seals for the highest tightness � spring loaded sealing systems according to TA-Luft /
VDI 2440 (approx. 100 bar, 450°C) and Fire-safe (160 bar, 750°C)
� long-time leak free due to spring supported compression of seal package
� TA-Luft conversion sets, complete with stuffing box packing, cover seal, spring sets and if required complete calculation checked by TüV for approval to TA-Luft suitability
For neutralising the stuffing box packing volume reduction due to usage, wear and aging
Dynamic seals for a long l i fe and an optimal operational certainty and profitabil i ty
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
The products in the NMF program comprise of a very complete package of special seals and swivels joints. Since dozens of years the sealing systems are used in the general-, chemical-, petrochemical- and steel industry, for paper production, agricultural, paints, water purification, machine building and food production installations. Important advantages are the life prolonging properties and the improved seal capacity, together leading to an improved seal system with higher reliability and a reduction in cost-of-ownership and downtime.
Camprofile gaskets third generation
� super elastic sealing element with an improved elastic recovery capacity
� reduced warehouse cost by integrating two or more pressure groups in one seal due to a break-away edge (patented)
� in compliance with EN 1514, EN 12560 as well as TA-Luft compliance
� ring-joints, spiral wound seals, welding seals and other special seals up to a diameter of 6 meter
� modern flange calculation software with standards according to EN 1591-1:2001, AD-Merkblatt 2000 B7/B8; ASME Code s.VIII and 4 more standards
To insure a tight flange coupling: flange calculation software for calculating the complete sealing system of the flanges
Special gaskets for installations in the high pressure and high temperature range
� spring loaded and blow-out safe seals according to the tension released construction principle
� spiral wound and carrier seals with a large resilience
� individual solutions for the optimization of a sealing system in e.g. for a manhole or high pressure heat exchanger
� including engineering, assembly and TüV approved and stamped documentation
To insure that regularly appearing fluctuations in pressure and temperature do not influence the sealing system and production process
Services at the installation
� conversion of valves to the TA-Luft-standard � repair, adaption, sealing and conversion of pumps
and valves to our seal system � measuring flanges with laser optics, assembly with
stretch bolt system � optimization of installations by hardening surfaces
with a layer welded on by laser � high chemical resistance, different layers are
available
Life prolonging, wear reduction, breakage preventing: use laser coted surfaces
Static seals in a large variety for control l ing extreme sealing situations
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
Swivel joints and rotary joints for complex and standard applications
Swivel joints in their most stable form
� for both liquid and gaseous media as rotating parts of the installation
� give pipes their proper position � available from 1/4” to 42”, in steel and stainless
steel � customisation possible due to a modular system � variable connections � movable arms as alternative for hoses � multi canal swivel joints on request with electrical
swivel joint to relay signals or power
For a reliable transport of media in a large variety of circumstances
Continuous rotating joints in many executions, light series
� diameters from 1/8” up to 4” � temperature up to 250°C � pressures up to 700 bar � mono-flow or duo-flow, fixed or rotating siphon � for media like water, air, vacuum, steam,
thermal- or hydraulic oil � for fast or slow rotation
Offering the possibility to transport one or more fluids between a fixed point and a rotating point
Hose loading arms and folding stairs for loading truck and railway with hoses or metal loading arms
� facilitating ease of operation and use � avoiding dangerous situations with smart
constructions � longer life of the hoses � higher safety level and lower risk of injuries during
operation by good handling system � environmental protection y guided hose movement � folding stairs up to 10 meter wide, safety cages,
optimisation of existing situations, etc.
Loading technology, individually adapted to the local situation
Visit us online on:
www.NMF-Group.com
NMF Techniek BV Tel.: +31(0)50 527 57 77 Woortmansdijk 30 Fax: +31(0)50 527 59 05 NL-9608 TB Westerbroek Email: [email protected]
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
6
Swivel Joint overview
I. Standard Swivel Joints with welding connection for application with different connections
Type W Type LW
II. Standard Swivel Joints with integrated threaded connection
Type T Type LT Type DH
III. Swivel Joints for food and pharmaceuticals (FDA conform)
Type F Type LF Type FP Type LFP
IV. Special Swivel Joints
In-between swivel joints High Temperature Swivel Joint
Type CF-TW Type CF
Type HT
Special Constructed Swivel Joints (to customer specifications)
V. Multi-canal Rotary Joint VI. Loading Equipment Swivel Joint Scissors
Standard Swivel Joints for Loading Arms
Type LA Type LCF Type HCR
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
7
Table of Contents
Swivel Joint type CF-TW for (Air-) Refuelling Systems 8
Swivel Joint type CF Center Flange 9
Swivel Joint type HT for high temperature applications 10
Special Constructed Swivel Joints (to customer specifications) 11
Swivel Joint type SO-HT: Special constructed swivel joint with 90° elbow ....................................................................... 11 Swivel Joint type SO-W: for “Floating Suction Systems” inside Storage Tanks ................................................................. 12 Swivel Joint type SO-LW-N: with Hose Socket ................................................................................................................. 13 Swivel Joint type SO-SL: with Oxygen Injector .................................................................................................................. 14 Swivel Joint type: Ball Swivel Joint .................................................................................................................................... 15 Swivel Joint type SO-T: with Leakage Control ................................................................................................................... 16 Swivel Joint type SO-CF: for High Speed Applications ...................................................................................................... 17 Swivel Joint type SO-SF: with Customized Flange ............................................................................................................. 18 Swivel Joint type SO-WF: with Customized Flange ........................................................................................................... 19
Ordering System 20
General Terms 21
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
8
Swivel Joint type CF-TW for (Air-) Refuelling Systems
Pos. Description
1 Outer part
2 Inner part
5 Back up ring
6 Internal wiper
10 Gasket
11 Dust seal
13 Plug
15 Ball
16 Grease nipple
Dimensions
Nominal diameter DN80 / 3" up to DN150 / 6"
Working pressure 10 bar / 145 psi *
Working temp. -55 °C up to 250 °C -67 °F up to 482 °F *
Material Aluminium
Gasket material PTFE
Ball material Stainless steel
Connection TW-Flange
Style 10
Application Airfield road tanker, aircraft-refuelling
*Pmax and Tmax may not occur at the same time
Technical Features
Design Customized
No. of ball races 2
Fluid Gasoline, Diesel, Kerosine (Jet A1,…)
Type of sealing Radial
External dust seal Yes
Secondary seal No
Body Two-parts
Connection for leakage control
No
Without grease nipple On request
Maximum speed Depends on nominal diameter
Further Advantages
Perfect concentric running, easy handling, lightweight
Dimensions and Weights
DN 80 100 150
L [mm] 100 100 120
ᴓ / D [mm] 154 174 240
ᴓ / d [mm] 74 97 154
ᴓ / k [mm] 130 150 210
Thread 8 x M10 8 x M12 12 x M12
Weight [kg] 3,9 4,5 8,8
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
9
Swivel Joint type CF Center Flange
Pos. Description
1 Outer part
2 Inner part
5 Back up ring
6 Internal wiper
10 Gasket
11 Dust seal
12 Plug
13 Plug
15 Ball
16 Grease nipple
Dimensions
Nominal diameter DN25 / 1“ up to DN1000 / 40“ [larger on request]
Working pressure Up to 420 bar / 6000 psi *
Working temp. -55 °C up to 250 °C -67 °F up to 482 °F *
Material According to customers spec.
Gasket material NBR, Viton, PTFE, HPU
Ball material Stainless steel
Connection Flange according to customers specifications
Style 10
Application Universal *Pmax and Tmax may not occur at the same time
Technical Features
Design Customized
No. of ball races 2
Fluid According to customers spec.
Type of sealing Radial
External dust seal Yes
Secondary seal No
Body Two-parts
Connection for leakage control
On request
Without grease nipple On request (e.g. floating suction systems)
Maximum speed Depends on gasket material
Further Advantages
Perfect concentric running, easy handling
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
10
Swivel Joint type HT for high temperature applications
Pos. Description Pos. Description
1 Outer part 12 Plug
2 Inner part 13 Plug Gasket 3 Flange
4 Thrust washer 14 Ball
5 Thrust ring 15 Grease nipple
8 Back up ring 16 Ventilation valve
9 Gasket 17 Allen screw
10 Compression gland
18 Hexagon bolt
11 Packing cord 19 Plug
Dimensions
Nominal diameter DN20/ 3/4" up to DN400/ 16" [larger on request]
Working pressure 100 bar / 1450 psi *
Working temp. Up to 600°C / 1112°F *
Material 1.4571, 42CrMo4, Duplex, Superduplex
Gasket material According to customers spec.
Ball material Stainless steel
Connection Welding
Style 10, 11, 12, 20, 21, 22, 30, 31
Application Solar panel systems / oil & gas *Pmax and Tmax may not occur at the same time
Technical Features
Design Customized
No. of ball races 2
Fluid Thermal oil, super critical steam, salt melt
Type of sealing Radial
External dust seal No
Secondary seal No
Body Three-parts
Connection for leakage control
On request
Without grease nipple On request
Maximum speed Depends on sealing material
Further Advantages
Adjustable gasket
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
11
Special Constructed Swivel Joints (to customer specifications) Next to the standard range of swivel joints we can tailor Swivel Joints according to customers’ requirements. Technical solutions are drafted and realized in close cooperation with the customer. The 3D-CAD-System Inventor enables us to design 3D-Prototypes of parts, to simulate movements and avoid collisions before production of the swivel starts.
Swivel Joint type SO-HT: Special constructed swivel joint with 90° elbow
Dimensions
Nominal diameter DN20 / 3/4" up to DN150 / 6" [larger on request]
Working pressure 100 bar / 1450 psi *
Working temp. Up to 600 °C / 1112 °F *
Material 1.4571, 42CrMo4, Duplex, Superduplex
Gasket material According to customers spec.
Ball material Stainless steel
Connection Welding
Style 11, 12, 20, 21, 22, 30, 31
Application Solar thermal power plants *Pmax and Tmax may not occur at the same time
Technical Features
Design Customized
No. of ball races 2
Fluid Thermal oil, super critical steam, salt melt
Type of sealing Radial
External dust seal No
Secondary seal No
Body Three-parts
Connection for leakage control
On request
Without grease nipple On request
Maximum speed Depends on sealing material
Further Advantages
Adjustable gasket
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
12
Swivel Joint type SO-W: for “Floating Suction Systems” inside Storage Tanks
Dimensions
Nominal diameter DN25 / 1" up to DN400 / 16"
Working pressure According to customers spec.
Working temp. According to customers spec.
Material 1.4571 [other materials on request. E.g. Aluminium, Hastelloy, etc.]
Gasket material According to customers spec.
Ball material Stainless steel
Connection Flange (ANSI/DIN/special), customized
Style Special
Application Floating suction, skimmer, floating roof draining
*Pmax and Tmax may not occur at the same time
Technical Features
Design Customized
No. of ball races 2-4
Fluid Diesel, Ethanol, LPG,…Water
Type of sealing Radial
External dust seal Yes
Secondary seal No
Body Three-parts
Connection for leakage control
No
Without grease nipple Yes
Maximum speed Depends on gasket material
Further Advantages
Less torsion due to the double suction orifice
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
13
Swivel Joint type SO-LW-N: with Hose Socket
Dimensions
Nominal diameter According to customers spec.
Working pressure According to customers spec.
Working temp. According to customers spec.
Material According to customers spec.
Gasket material According to customers spec.
Ball material Stainless steel
Connection Flange (ANSI/DIN/customized), welding, threaded (male/female, NPT, BSP, etc.), olive style, special
Style 10
Application Universal *Pmax and Tmax may not occur at the same time
Technical Features
Design Customized
No. of ball races 1 (2)
Fluid According to customers spec.
Type of sealing Radial
External dust seal Yes
Secondary seal No
Body Two-parts
Connection for leakage control
No
Without grease nipple On request (e.g. floating suction systems)
Maximum speed Depends on sealing material
Further Advantages
Perfect concentric run, simple handling, smaller compared to the LW with connections welded on
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
14
Swivel Joint type SO-SL: with Oxygen Injector
Dimensions
Nominal diameter According to customers spec.
Working pressure According to customers spec.
Working temp. According to customers spec.
Material 1.4571 [others on request. E.g. Hastelloy, etc.]
Gasket material According to customers spec.
Ball material Stainless steel
Connection Flange (ANSI/DIN/Special), customized
Style 10, 11
Application Steel mill, … *Pmax and Tmax may not occur at the same time
Technical Features
Design Customized
No. of ball races 2
Fluid Oxygen, …
Type of sealing Radial
External dust seal Yes
Secondary seal No
Body Three-parts
Connection for leakage control
Yes
Without grease nipple On request
Maximum speed Depends on sealing material
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
15
Swivel Joint type: Ball Swivel Joint
Dimensions
Nominal diameter DN50 / 2“ up to DN500 / 20“ [larger on request]
Working pressure 16 bar / 232 psi *
Working temp. Up to 150°C Up to 302°F *
Movement up/down +/- 15°
Material According to customers spec.
Gasket material According to customers spec.
Ball material Stainless steel
Connection According to customers spec.
Style 10, 11, 12, 20, 21, 22, 30, 31
Application Universal *Pmax and Tmax may not occur at the same time
Technical Features
Design Customized
No. of ball races No
Fluid According to customers spec.
Type of sealing Radial
External dust seal No
Secondary seal No
Body Three-parts
Connection for leakage control
No
Without grease nipple Yes
Maximum speed Depends on sealing material
Further Advantages
Multidimensional movement
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
16
Swivel Joint type SO-T: with Leakage Control
Dimensions
Nominal diameter DN15 / 1/2“ [larger on request]
Working pressure 10 bar / 145 psi *
Working temp. Up to 250 °C up to 482°F *
Material 1.4571 [other materials on request. E.g. Aluminium, Hastelloy, etc.]
Gasket material According to customers spec.
Lagers Depends on ball bearing used
Connection Threaded (male/female, NPT, BSP, etc.), olive style, customized
Style 11
Application Universal *Pmax and Tmax may not occur at the same time
Technical Features
Design Customized
No. of ball races 2 Ball bearings
Fluid Compressed air, …
Type of sealing Radial
External dust seal Yes
Secondary seal Yes
Body Two parts
Connection for leakage control
Yes
Without grease nipple Yes
Maximum speed High, depending on seal material
Further Advantages
Ball bearings and lip seals for higher speed
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
17
Swivel Joint type SO-CF: for High Speed Applications
Dimensions
Nominal diameter DN25 / 1“ up to DN150 / 6“ [larger on request]
Working pressure 10 bar / 145 psi *
Working temp. Up to 110 °C Up to 230 °F *
Material 1.4571 [other materials on request. E.g. Aluminium, Hastelloy, etc.]
Gasket material According to customers spec.
Ball material Depends on ball bearing used
Connection Flange (ANSI/DIN/special), customized
Style 10, 11, 12, 20, 21,22, 30, 31
Application Automated food packaging *Pmax and Tmax may not occur at the same time
Technical Features
Design Customized
No. of ball races 2 Ball bearings
Fluid According to customers spec.
Type of sealing Radial
External dust seal Yes
Secondary seal No
Body Three-parts
Connection for leakage control
Yes
Without grease nipple On request (e.g. floating suction system)
Maximum speed High, depends on gasket material
Further Advantages
Ball bearings for high speed revolution
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
18
Swivel Joint type SO-SF: with Customized Flange
Pos. Description
1 Outer part
2 Inner part
5 Back up ring
6 Internal wiper
10 Gasket
11 Dust seal
12 Plug
13 Plug
15 Ball
16 Grease nipple
Dimensions
Nominal diameter According to customers spec.
Working pressure Up to 1000 bar Up to 14500 psi *
Working temp. According to customers spec.
Material 42CrMo4 [other materials on request]
Gasket material NBR, Viton, PTFE, HPU
Ball material Stainless steel
Connection Flange (ANSI/DIN/special), welding, threaded (male/female, NPT, BSP, etc.), compression fitting, customized
Style 10, 11, 12
Application Universal *Pmax and Tmax may not occur at the same time
Technical Features
Design Customized
No. of ball races 2
Fluid According to customers spec.
Type of sealing Radial
External dust seal Yes
Secondary seal No
Body Two-parts
Connection for leakage control
On request
Without grease nipple On request
Maximum speed Depends on gasket material
Further Advantages
Perfect concentric running, easy handling
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
19
Swivel Joint type SO-WF: with Customized Flange
Pos. Description
1 Outer part
2 Inner part
10 Gasket
11 Dust seal
12 Plug
13 Plug
15 Ball
16 Grease nipple
Dimensions
Nominal diameter DN25 / 1“ up to DN150 / 6“ [larger on request]
Working pressure 420 bar 6000 psi *
Working temp. 80 °C 176°F*
Material 42CrMo4 [other materials on request]
Gasket material According to customers spec.
Ball material Stainless steel
Connection Flange (ANSI/DIN/special), customized
Style 10, 11, 12
Application Universal *Pmax and Tmax may not occur at the same time
Technical Features
Design Customized
No. of ball races 2
Fluid According to customers spec.
Type of sealing Radial
External dust seal Yes
Secondary seal No
Body Two-parts
Connection for leakage control
On request
Without grease nipple On request
Maximum speed Depends on gasket material
Further Advantages
Perfect concentric running, easy handling
v13.6.13
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
20
Ordering System
Type Connection right / left
Style Nominal diameter
Material Working pressure
Miscellaneous
W SO = special 10 DN 20 St52-3 Tot 420 bar DIN
LW __ = Welding 11 to 1.4571 Tot 6000 psi ANSI
T F = Flange 12 DN 700 42CrMo4 SAE
LT S = Female Thread
Duplex …
V N = Male Thread 20 (up to DN1000 Hastelloy (for applications
LA 21 on request) Superduplex with higher
LCF 22 pressure we
HCR (other materials offer special
F 30 on request) swivel joints)
LF 31
FP
LFP
Additional Information
Medium:
Working temp.:
Working space situation (Dimensions, temperature of environment, etc…):
Type of movement (Swiveling / angle?, Rotation / rpm?,…):
Side load:
Miscellaneous requirements:
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
NMF Techniek BV General Terms and Conditions of sale.
1.DEFINITIONS
In these terms and conditions "the Company" means NMF Techniek BV, "the Customer" means the person or Company with whom the
Contract is made and “the Goods" means the products sold by the Company to the Customer. The Manufacturer being VR Dichtungen
B.V. and GmbH.
2.GENERAL
These Terms and Conditions are part of all our quotations until and also include the agreements and acceptance of orders and/or
services. No variations of these conditions in any document of the Customer shall be applicable unless accepted in writing by the
Company.
3.QUOTATIONS
All our quotations, price lists, catalogues, drawings, descriptions en conditions are free and not binding to the Company. The applicant is
responsible for the details given to the company and for the way and form in which said details are presented to us. The Company
reserves in all cases and times - even when the Customer has paid for the costs - the rights, ownership and copyright of all of the
Company’s quotations, designs, calculations, constructions, drawings, moulds, etc. Said items cannot be used, sold or whatsoever by
the Customer without written consent of the Company, nor given to third parties in use or for inspection or whatsoever.
4.AGREEMENT
The agreement is made only after the Company has accepted the agreement in writing or as soon as the Company has made the invoice
and delivery. Objection against the order acceptance have to be received by the Company within five (5) days after the date of the order
acceptance or invoice date. After that the Customer will be bound to said order acceptance or invoice. Conditions of Purchase of the
Customer are not accepted except for a written statement from the Company stating otherwise.
5.PRICES
Our prices are for delivery ex works Groningen unless otherwise agreed in writing. The prices are ex packing and freight. These prices
are based on at the time of the acceptance of the order valid prices and conditions of our suppliers, rate of exchange, wages, import
duties, taxes, etc. In case of a raise of any of these the Company reserves the right to correct any discrepancies on the date of the
shipment.
6. -
7.TIME OF DELIVERY
The delivery times are given by the Company as exact as possible, but are without engagement and not binding. When delivery times
are exceeded the Customer has not the right to cancel the order nor is entitled to any compensation.
8.DELIVERY
Delivery is ex warehouse Groningen or ex warehouse of our suppliers. The goods are with regard to delivery time and risk transit
delivered at the moment that the goods leave said warehouses for shipment to the Customer. Insurance for the transport risks, etc. will
be covered by the Customer. EXW Incoterms 1990Groningen.
9.PAYMENT
All payments for any invoice are to be settled by payment via a Bank 30 days after the date of the invoice, without any deduction of any
discounts or compensations, unless they are written on the invoice. The duty to pay is not suspended by claims, complaints or whatever
other circumstances. By not paying within said period the Company shall be entitled to charge interest of 2% on top of the promissory
note of the Dutch National Bank.
Failure to pay any invoice in accordance with the foregoing or other terms specified in the Contract shall entitle the Company to suspend
further deliveries. Any costs the Company has to make to receive payment are for the full amount, and will be charged in full, to the
Customer.
10.OWNERSHIP
Ownership in the goods will not pass to the Customer until payment for the goods has been received by the Company in full. Until the
time of actual payment to the Company of the total amounts owing in respect of goods the Customer shall keep the goods on behalf of
the Company and shall store the goods in such a way that they are separately identifiable; nevertheless prior to the time of actual
payment for the goods, the customer is entitled to use the goods in normal course of its business or to resell the goods to third parties in
the normal course of its business on behalf of and for the account of the Company (but so that the Customer shall not be deemed as
NMF Techniek BV ▪ Woortmansdijk 30 ▪ NL-9608 TB Westerbroek tel. +31(0)50 527 57 77 ▪ fax +31(0)50 527 59 05 ▪ [email protected] ▪ www.NMF-Group.com
against any such third party to be the agent of the Company) on the condition that the goods and any amounts received from third parties
for the goods are held by the Customer as trustee for the Company pending payment in full to the Company and the Customer hereby
assigns to the Company all rights and claims that the customer has against any such party.
11.WARRANTY AND LIABILITY
The Company warrants in relation to goods not of the Company's manufacture (including but not limited to parts and components
supplied by others for goods manufactured by the Company) and it will so far as it is able to do so give the Customer the benefit of any
express guarantee or warranty by the manufacturer or supplier of such goods and of any other rights which the Company has against the
manufacturer or supplier.
The Customer's remedies in respect of any claim under the foregoing express warranty or against any manufacturer or supplier as
aforesaid or any claim under any condition or warranty implied by Dutch law or any other claim in respect of the goods or any
workmanship in relation thereto (whether or not involving negligence on the part of the Company) shall be limited to repair or
replacement or refund of the purchase price as aforesaid and any condition or warranty implied by Dutch law shall cease to apply after
the expiry of the warranty period and in all other cases shall be limited to the enforcement of the abovementioned liabilities of the
manufacturer or supplier. The Company shall not in any circumstances be liable for any damages, compensation, costs, expenses,
losses or other liabilities, whether direct or consequential, and any other remedy which would otherwise be available in law is hereby
excluded except to the extent that such exclusion is prohibited by any rule of law. The Company will in no circumstances accept liability
for damage or defects arising from misuse, misloading or overloading of goods nor for goods which have been altered or repaired or
wrongly mounted or added to otherwise than by the Company or in a manner approved in writing by the Company.
In the event of an order being to a Customer's specification or design the Company shall be under no liability of any kind in respect of the
Goods being fit for any particular purpose, even if such purpose is made known to the Company. A claim in relation to any goods in
accordance with any of the foregoing provisions shall not entitle the customer to cancel the Contract or any part thereof or to refuse to
take delivery of or to pay for those goods or any other goods(whether under the same or any other Contract).
The Company only gives a guarantee in case the Manufacturer gives a guarantee.
12.CLAIMS
The Customer has to check the goods upon arrival. In case of visual defects, wrong quantities or errors in sizes the Customer has to put
in a claim with the Company within ten (20) days after the date of invoice and the shipping date. The Company will not accept any later
complaints.
13.The Customer shall indemnify the Company against all actions, costs, (including the cost of defending any legal proceedings), claims,
proceedings, accounts and damages in respect of any infringement or alleged infringement of any patent, registered design, copyright,
trade mark or other industrial or intellectual property rights resulting from compliance by the Company with the Customer's instructions,
whether express or implied.
14.IMPORTS
The Customer shall be responsible for complying with any legislation rules or regulations governing the importation of the goods and for
the payment of any duties thereon and for obtaining any necessary licences and permissions to enable the goods to be imported into the
country of destination.
15.DISPUTES
All disputes or claims which may arise out of or in connection with the Contract shall be referred to an Arbitrator in Groningen, The
Netherlands. The choice of Arbitrators to be agreed between parties to be either a qualified Judge, the Chairman of the Chamber of
Commerce or a third party, who is an agreed choice of both parties and as a just man, or just men, shall give a reasonable and binding
advice. The Arbitrator shall apply Dutch law.
16.APPROPRIATE LAW
The Contract shall in all respects be governed by and construed in accordance with the law of the Netherlands and the Customer admits
to the jurisdiction of Dutch Courts.17.COURTIn case parties decide to go to court, the following rule will apply: if parties decide to go to
court, they will have to go to a Dutch Court in Groningen, The Netherlands and proceed according to Dutch Law;18.In case of difference
of opinion about this translation, the Dutch text will in all cases prevail for this difference in opinion.
Groningen, September 1, 1991