o r ta s o t 02 t es trpo n 03 c hứngc ỉg reengua d  04 c … · 2020-03-24 · staron solid...
TRANSCRIPT
ĐÁ NHÂN TẠO STARON
01 Giới thiệu02 Test report03 Chứng chỉ Greenguard 04 Chứng chỉ NSF05 Chứng chỉ IQNET06 Chứng chỉ khác07 07 MSDS08 Bảo hành
ĐÁ NHÂN TẠO CAO CẤP
STARON
Staron là thương hiệu đá nhân tạo solid surface
của Lotte Advanced Materials đến từ Hàn
Quốc. Được mệnh danh là dòng đá nhân tạo
cao cấp tại Hàn Quốc, Staron hứa hẹn là vật liệu
tối ưu thế hệ mới trong thiết kế nội thất.
Staron solid surface được phát triển từ năm
1992 với sự đa dạng về màu sắc đáp ứng được
bất kỳ nhu cầu thiết kế nào. Với nhiều ưu điểm
vượt trội, đá nhân tạo Staron được sử dụng rộng
rãi trong các ứng dụng nội và ngoại thất ở các
khu dân cư và thương mại.
Staron đa dạng màu sắc với nhiều dòng sản
phẩm: Supreme, Solid, Sanded, Aspen, Pebble,
Quarry, Crystal, Metallic, Tempest, Evermoin.
STARON
SOLID SURFACE
Staron is a solid surface brand of Lotte
Advanced Materials from Korea. Dubbed as
a high-end artificial stone line in Korea, Staron
is promised to be the optimal new generation
material in interior design.
Staron solid surface has been developed since
1992 with a variety of colors to meet any design
needs. With many outstanding advantages,
Staron artificial stone is widely used in interior
and exterior applications in residential and
commercial areas.
Staron has a variety of colors with many
product lines: Supreme, Solid, Sanded, Aspen,
Pebble, Quarry, Crystal, Metallic, Tempest,
Evermoin.
Mẫu
(Pattern)
Độ dày
(Thickness)
Rộng
(Width)
Dài
(Length)
SOLID
SANDED
ASPEN
6mm 760mm 2,500mm
12mm 760mm 3,680mm
PEBBLE
METALLIC
QUARY
TEMPEST
SUPREME
12mm 760mm 3,680mm
Test Completion Date : 2017.07.11.
Receipt Date : 2017.07.03.
Address : 56, Gosan-ro, Uiwang-si, Gyeonggi-do, Korea 16073
Company name: Lotte Advanced Materials Co., Ltd.
Representative : Lee Ja Hyung
Report No : TAK-016406
98, Gyoyukwon-ro, Gwacheon-si, Gyeonggi-do, 13810, Rep. of KOREA TEL 82-2-2164-0011 FAX 82-2-2634-1008
Sample name : Artificial Marble (STARON)
Test Results
TEST ITEM UNIT SAMPLE RESULT TEST METHOD
ASTM D792-13(Method A)1.78--Specific Gravity((23/23) ℃)
ASTM D570-98(2010)e10.03-%Water Absorption(24 h Immersion)
ASTM D2583-13a67--Barcol Hardness
ASTM D785-08(2015)(Procedure A)
93--Rockwell Hardness(HRM)
ASTM D256-10e1(Method A)
18-J/mIzod Impact Strength
ASTM D638-14(*)36.4-MPaTensile Strength
ASTM D790-15e2(**)53.5-MPaFlexural Strength
ASTM D790-15e2(**)10.5-GPaFlexural Modulus of Elasticity
JIS K 6911 : 19956.5×10-1/℃Thermal Expansion
ASTM D648-16(Method B)109-℃Deflection Temperature Under Load(1.82 MPa)
JIS K 6902 : 2007(Method B)No Defects--Heat Resistance(Appearance)
JIS K 6902 : 2007(Method B)No Defects--Heat Water Resistance(Appearance)
By The Client(***)No Defects--Dropping Impact Test
- Next Page -
Technical Manager: You SeokTel: 1577-0091(ARS ①→④)
Tested by JungyuseokE-mail: [email protected]
Jungyuseok You Seok
Korea Testing & Research Institute
2017.07.11.
21 of
President
전자문서본(Electronic Copy)
QR Code for forgery
Electronic copy is for your reference only.
Page:
Test Completion Date : 2017.07.11.
Receipt Date : 2017.07.03.
Address : 56, Gosan-ro, Uiwang-si, Gyeonggi-do, Korea 16073
Company name: Lotte Advanced Materials Co., Ltd.
Representative : Lee Ja Hyung
Report No : TAK-016406
98, Gyoyukwon-ro, Gwacheon-si, Gyeonggi-do, 13810, Rep. of KOREA TEL 82-2-2164-0011 FAX 82-2-2634-1008
Sample name : Artificial Marble (STARON)
Test Results
TEST ITEM UNIT SAMPLE RESULT TEST METHOD
* Speed of Testing: 5 mm/min, Specimen Type: Type I** Speed of Testing: 5.0 mm/min, Support Span: 190 mm*** Fall height : 2 m, 112 g(bearing ball), Test specimen : Concrete, Appearance : Crack
- Usage of Report: QUALITY CONTROL
NOTE : 1. The test results of this test report are only limited in to the samples and sample names provided by the client and do not guarantee the quality of all products of the client. You can check website (www.ktr.or.kr) or QR code to verify the authenticity of the certificate.2. This test report shall be used only within the purpose of its defined usage and shall not be used for public relation, advertisement and lawsuit.3. This test report is only valid when printed on KTR original report paper with hologram and when re-issued by KTR. The copy and the electronic file of the test report are only for reference.
Technical Manager: You SeokTel: 1577-0091(ARS ①→④)
Tested by JungyuseokE-mail: [email protected]
Jungyuseok You Seok
Korea Testing & Research Institute
2017.07.11.
22 of
President
전자문서본(Electronic Copy)
QR Code for forgery
Electronic copy is for your reference only.
Page:
A4(210 Χ 297)KTR-QP-T09-F01-05(01)
LOTTE ADVANCEDMATERIALS CO., LTDStaron® solid surface sheetsRestrictions:
Certified
Status
09/18/2007 - 09/18/2019
Certificate Period
4109-410
Certificate Number
UL 2818 - 2013 Standard for Chemical Emissions for Building Materials, Finishes and Furnishings
CERTIFICATEOF COMPLIANCE
Building materials are determined compliant in accordance with an Office environment with an air change of 0.68 hr¯¹ and a loading of 3.20 m².
Products tested in accordance with UL 2821 test method to show compliance to emission limits in UL 2818, Section 7.1.
GREENGUARD Certification Criteria for Building Products and Interior Finishes
Criteria CAS NumberMaximum Allowable
Predicted Concentration Units
TVOC(A) - 0.50 mg/m³
Formaldehyde 50-00-0 61.3 (50 ppb) µg/m³
Total Aldehydes (B) - 0.10 ppm
Particle Matter less than 10 µm (C) - 50 µg/m³
4-Phenylcyclohexene 4994-16-5 6.5 µg/m³
Individual VOCs (D) - 1/10th TLV -
(A) Defined to be the total response of measured VOCs falling within the C6 – C16 range, with responses calibrated to a toluene surrogate. Maximum allowable predicted TVOC concentra�ons for GREENGUARD (0.50 mg/m³) fall in the range of 0.5 mg/m³ or less, as specified in CDPH Standard Method v1.1.
(B) The sum of all measured normal aldehydes from formaldehyde through nonanal, plus benzaldehyde, individually calibrated to a compound specific standard. Heptanal through nonanal are measured via TD/GC/MS analysis and the remaining aldehydes are measured using HPLC/UV analysis.
(C) Par�cle emission requirement only applicable to HVAC Duct Products with exposed surface area in air streams (a forced air test with specific test method) and for wood finishing (sanding) systems.
(D) Allowable levels for chemicals not listed are derived from 1/10th of the Threshold Limit Value (TLV) industrial work place standard (Reference: American Conference of Government Industrial Hygienists, 6500 Glenway, Building D-7, and Cincinna�, OH 45211-4438).
LOTTE ADVANCED MATERIALS CO., LTDStaron® solid surface Sinks and BowlsRestrictions:
Certified
Status
09/18/2007 - 09/18/2019
Certificate Period
4112-410
Certificate Number
UL 2818 - 2013 Standard for Chemical Emissions for Building Materials, Finishes and Furnishings
CERTIFICATEOF COMPLIANCE
Building materials are determined compliant in accordance with an Office environment with an air change of 0.68 hr¯¹ and a loading of 3.20 m².
Products tested in accordance with UL 2821 test method to show compliance to emission limits in UL 2818, Section 7.1.
UL Environment investigated representative samples of the identified Product(s) to the identified Standard(s) or other requirements in accordance with the agreements and any applicable program service terms in place between UL Environment and the Certificate Holder (collectively “Agreement”). The Certificate Holder is authorized to use the UL Environment Mark for the identified Product(s) manufactured at the production site(s) covered by the ULE Test Report, in accordance with the terms of the Agreement. This Certificate is valid for the identified dates unless there is non-compliance with the Agreement.
GREENGUARD Certification Criteria for Building Products and Interior Finishes
Criteria CAS NumberMaximum Allowable
Predicted Concentration Units
TVOC(A) - 0.50 mg/m³
Formaldehyde 50-00-0 61.3 (50 ppb) µg/m³
Total Aldehydes (B) - 0.10 ppm
Particle Matter less than 10 µm (C) - 50 µg/m³
4-Phenylcyclohexene 4994-16-5 6.5 µg/m³
Individual VOCs (D) - 1/10th TLV -
(A) Defined to be the total response of measured VOCs falling within the C6 – C16 range, with responses calibrated to a toluene surrogate. Maximum allowable predicted TVOC concentra�ons for GREENGUARD (0.50 mg/m³) fall in the range of 0.5 mg/m³ or less, as specified in CDPH Standard Method v1.1.
(B) The sum of all measured normal aldehydes from formaldehyde through nonanal, plus benzaldehyde, individually calibrated to a compound specific standard. Heptanal through nonanal are measured via TD/GC/MS analysis and the remaining aldehydes are measured using HPLC/UV analysis.
(C) Par�cle emission requirement only applicable to HVAC Duct Products with exposed surface area in air streams (a forced air test with specific test method) and for wood finishing (sanding) systems.
(D) Allowable levels for chemicals not listed are derived from 1/10th of the Threshold Limit Value (TLV) industrial work place standard (Reference: American Conference of Government Industrial Hygienists, 6500 Glenway, Building D-7, and Cincinna�, OH 45211-4438).
UL Environment investigated representative samples of the identified Product(s) to the identified Standard(s) or other requirements in accordance with the agreements and any applicable program service terms in place between UL Environment and the Certificate Holder (collectively “Agreement”). The Certificate Holder is authorized to use the UL Environment Mark for the identified Product(s) manufactured at the production site(s) covered by the ULE Test Report, in accordance with the terms of the Agreement. This Certificate is valid for the identified dates unless there is non-compliance with the Agreement.
LOTTE ADVANCED MATERIALS CO., LTDStaron® Tempest™Restrictions:
Certified
Status
09/18/2007 - 09/18/2019
Certificate Period
4110-410
Certificate Number
UL 2818 - 2013 Standard for Chemical Emissions for Building Materials, Finishes and Furnishings
CERTIFICATEOF COMPLIANCE
Building materials are determined compliant in accordance with an Office environment with an air change of 0.68 hr¯¹ and a loading of 3.20 m².
Products tested in accordance with UL 2821 test method to show compliance to emission limits in UL 2818, Section 7.1.
GREENGUARD Certification Criteria for Building Products and Interior Finishes
Criteria CAS NumberMaximum Allowable
Predicted Concentration Units
TVOC(A) - 0.50 mg/m³
Formaldehyde 50-00-0 61.3 (50 ppb) µg/m³
Total Aldehydes (B) - 0.10 ppm
Particle Matter less than 10 µm (C) - 50 µg/m³
4-Phenylcyclohexene 4994-16-5 6.5 µg/m³
Individual VOCs (D) - 1/10th TLV -
(A) Defined to be the total response of measured VOCs falling within the C6 – C16 range, with responses calibrated to a toluene surrogate. Maximum allowable predicted TVOC concentra�ons for GREENGUARD (0.50 mg/m³) fall in the range of 0.5 mg/m³ or less, as specified in CDPH Standard Method v1.1.
(B) The sum of all measured normal aldehydes from formaldehyde through nonanal, plus benzaldehyde, individually calibrated to a compound specific standard. Heptanal through nonanal are measured via TD/GC/MS analysis and the remaining aldehydes are measured using HPLC/UV analysis.
(C) Par�cle emission requirement only applicable to HVAC Duct Products with exposed surface area in air streams (a forced air test with specific test method) and for wood finishing (sanding) systems.
(D) Allowable levels for chemicals not listed are derived from 1/10th of the Threshold Limit Value (TLV) industrial work place standard (Reference: American Conference of Government Industrial Hygienists, 6500 Glenway, Building D-7, and Cincinna�, OH 45211-4438).
UL Environment investigated representative samples of the identified Product(s) to the identified Standard(s) or other requirements in accordance with the agreements and any applicable program service terms in place between UL Environment and the Certificate Holder (collectively “Agreement”). The Certificate Holder is authorized to use the UL Environment Mark for the identified Product(s) manufactured at the production site(s) covered by the ULE Test Report, in accordance with the terms of the Agreement. This Certificate is valid for the identified dates unless there is non-compliance with the Agreement.
UL Environment investigated representative samples of the identified Product(s) to the identified Standard(s) or other requirements in accordance with the agreements and any applicable program service terms in place between UL Environment and the Certificate Holder (collectively “Agreement”). The Certificate Holder is authorized to use the UL Environment Mark for the identified Product(s) manufactured at the production site(s) covered by the ULE Test Report, in accordance with the terms of the Agreement. This Certificate is valid for the identified dates unless there is non-compliance with the Agreement.
UL Environment investigated representative samples of the identified Product(s) to the identified Standard(s) or other requirements in accordance with the agreements and any applicable program service terms in place between UL Environment and the Certificate Holder (collectively “Agreement”). The Certificate Holder is authorized to use the UL Environment Mark for the identified Product(s) manufactured at the production site(s) covered by the ULE Test Report, in accordance with the terms of the Agreement. This Certificate is valid for the identified dates unless there is non-compliance with the Agreement.
UL Environment investigated representative samples of the identified Product(s) to the identified Standard(s) or other requirements in accordance with the agreements and any applicable program service terms in place between UL Environment and the Certificate Holder (collectively “Agreement”). The Certificate Holder is authorized to use the UL Environment Mark for the identified Product(s) manufactured at the production site(s) covered by the ULE Test Report, in accordance with the terms of the Agreement. This Certificate is valid for the identified dates unless there is non-compliance with the Agreement.
Restrictions:
LOTTE ADVANCED MATERIALS CO., LTDStaron® solid surface sheets
4109-420
Certificate Number
09/18/2007 - 09/18/2019
Certificate Period
Certified
Status
UL 2818 - 2013 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings
CERTIFICATEOF COMPLIANCE
Building products and interior finishes are determined compliant in accordance with California Department of Public Health (CDPH) Standard Method V1.2-2017 using an Office and Classroom Environment.
Product tested in accordance with UL 2821 test method to show compliance to emission limits on UL 2818. Section 7.1 and 7.2.
UL Environment investigated representative samples of the identified Product(s) to the identified Standard(s) or other requirements in accordance with the agreements and any applicable program service terms in place between UL Environment and the Certificate Holder (collectively “Agreement”). The Certificate Holder is authorized to use the UL Environment Mark for the identified Product(s) manufactured at the production site(s) covered by the ULE Test Report, in accordance with the terms of the Agreement. This Certificate is valid for the identified dates unless there is non-compliance with the Agreement.
Restrictions:
LOTTE ADVANCED MATERIALS CO., LTDStaron® solid surface Sinks and Bowls
4112-420
Certificate Number
09/18/2007 - 09/18/2019
Certificate Period
Certified
Status
UL 2818 - 2013 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings
CERTIFICATEOF COMPLIANCE
Building products and interior finishes are determined compliant in accordance with California Department of Public Health (CDPH) Standard Method V1.2-2017 using an Office and Classroom Environment.
Product tested in accordance with UL 2821 test method to show compliance to emission limits on UL 2818. Section 7.1 and 7.2.
UL Environment investigated representative samples of the identified Product(s) to the identified Standard(s) or other requirements in accordance with the agreements and any applicable program service terms in place between UL Environment and the Certificate Holder (collectively “Agreement”). The Certificate Holder is authorized to use the UL Environment Mark for the identified Product(s) manufactured at the production site(s) covered by the ULE Test Report, in accordance with the terms of the Agreement. This Certificate is valid for the identified dates unless there is non-compliance with the Agreement.
Restrictions:
LOTTE ADVANCED MATERIALS CO., LTDStaron® Tempest™
4110-420
Certificate Number
09/18/2007 - 09/18/2019
Certificate Period
Certified
Status
UL 2818 - 2013 Gold Standard for Chemical Emissions for Building Materials, Finishes and Furnishings
CERTIFICATEOF COMPLIANCE
Building products and interior finishes are determined compliant in accordance with California Department of Public Health (CDPH) Standard Method V1.2-2017 using an Office and Classroom Environment.
Product tested in accordance with UL 2821 test method to show compliance to emission limits on UL 2818. Section 7.1 and 7.2.
UL Environment investigated representative samples of the identified Product(s) to the identified Standard(s) or other requirements in accordance with the agreements and any applicable program service terms in place between UL Environment and the Certificate Holder (collectively “Agreement”). The Certificate Holder is authorized to use the UL Environment Mark for the identified Product(s) manufactured at the production site(s) covered by the ULE Test Report, in accordance with the terms of the Agreement. This Certificate is valid for the identified dates unless there is non-compliance with the Agreement.
GREENGUARD Gold Certification Criteria for Building Products and Interior Finishes
Criteria CAS NumberMaximum Allowable
Predicted Concentration Units
TVOC (A) - 0.22 mg/m³
Formaldehyde 50-00-0 9 (7.3 ppb) µg/m³
Total Aldehydes (B) - 0.043 ppm
4-Phenylcyclohexene 4994-16-5 6.5 µg/m³
Particle Matter less than 10 µm (C) - 20 µg/m³
1-Methyl-2-pyrrolidinone (D) 872-50-4 160 µg/m³
Individual VOCs (E) -1/2 CREL
or1/100th TLV
-
(A) Defined to be the total response of measured VOCs falling within the C6 – C16 range, with responses calibrated to a toluene surrogate. Maximum allowable predicted TVOC concentra�ons for GREENGUARD Gold (0.22 mg/m³) fall in the range of 0.5 mg/m³ or less, as specified in CDPH Standard Method v1.2.
(B) The sum of all measured normal aldehydes from formaldehyde through nonanal, plus benzaldehyde, individually calibrated to a compound specific standard. Heptanal through nonanal are measured via TD/GC/MS analysis and the remaining aldehydes are measured using HPLC/UV analysis.
(C) Par�cle emission requirement only applicable to HVAC Duct Products with exposed surface area in air streams (a forced air test with specific test method) and for wood finishing (sanding) systems.
(D) Based on the CA Prop 65 Maximum Allowable Dose Level for inhala�on of 3,200 μg/day and an inhala�on rate of 20 m³/day
(E) Allowable levels for chemicals not listed are derived from the lower of 1/2 the California Office of Environmental Health Hazard Assessment (OEHHA) Chronic Reference Exposure Level (CREL) as required per the CDPH/EHLB/Standard Method v1.2 and BIFMA level credit 7.6.2 and 1/100th of the Threshold Limit Value (TLV) industrial work place standard (Reference: American Conference of Government Industrial Hygienists, 6500 Glenway, Building D-7, and Cincinna�, OH 45211-4438).
UL Environment investigated representative samples of the identified Product(s) to the identified Standard(s) or other requirements in accordance with the agreements and any applicable program service terms in place between UL Environment and the Certificate Holder (collectively “Agreement”). The Certificate Holder is authorized to use the UL Environment Mark for the identified Product(s) manufactured at the production site(s) covered by the ULE Test Report, in accordance with the terms of the Agreement. This Certificate is valid for the identified dates unless there is non-compliance with the Agreement.
UL Environment investigated representative samples of the identified Product(s) to the identified Standard(s) or other requirements in accordance with the agreements and any applicable program service terms in place between UL Environment and the Certificate Holder (collectively “Agreement”). The Certificate Holder is authorized to use the UL Environment Mark for the identified Product(s) manufactured at the production site(s) covered by the ULE Test Report, in accordance with the terms of the Agreement. This Certificate is valid for the identified dates unless there is non-compliance with the Agreement.
GREENGUARD Gold Certification Criteria for Building Products and Interior Finishes
Criteria CAS NumberMaximum Allowable
Predicted Concentration Units
TVOC (A) - 0.22 mg/m³
Formaldehyde 50-00-0 9 (7.3 ppb) µg/m³
Total Aldehydes (B) - 0.043 ppm
4-Phenylcyclohexene 4994-16-5 6.5 µg/m³
Particle Matter less than 10 µm (C) - 20 µg/m³
1-Methyl-2-pyrrolidinone (D) 872-50-4 160 µg/m³
Individual VOCs (E) -1/2 CREL
or1/100th TLV
-
(A) Defined to be the total response of measured VOCs falling within the C6 – C16 range, with responses calibrated to a toluene surrogate. Maximum allowable predicted TVOC concentra�ons for GREENGUARD Gold (0.22 mg/m³) fall in the range of 0.5 mg/m³ or less, as specified in CDPH Standard Method v1.2.
(B) The sum of all measured normal aldehydes from formaldehyde through nonanal, plus benzaldehyde, individually calibrated to a compound specific standard. Heptanal through nonanal are measured via TD/GC/MS analysis and the remaining aldehydes are measured using HPLC/UV analysis.
(C) Par�cle emission requirement only applicable to HVAC Duct Products with exposed surface area in air streams (a forced air test with specific test method) and for wood finishing (sanding) systems.
(D) Based on the CA Prop 65 Maximum Allowable Dose Level for inhala�on of 3,200 μg/day and an inhala�on rate of 20 m³/day
(E) Allowable levels for chemicals not listed are derived from the lower of 1/2 the California Office of Environmental Health Hazard Assessment (OEHHA) Chronic Reference Exposure Level (CREL) as required per the CDPH/EHLB/Standard Method v1.2 and BIFMA level credit 7.6.2 and 1/100th of the Threshold Limit Value (TLV) industrial work place standard (Reference: American Conference of Government Industrial Hygienists, 6500 Glenway, Building D-7, and Cincinna�, OH 45211-4438).
UL Environment investigated representative samples of the identified Product(s) to the identified Standard(s) or other requirements in accordance with the agreements and any applicable program service terms in place between UL Environment and the Certificate Holder (collectively “Agreement”). The Certificate Holder is authorized to use the UL Environment Mark for the identified Product(s) manufactured at the production site(s) covered by the ULE Test Report, in accordance with the terms of the Agreement. This Certificate is valid for the identified dates unless there is non-compliance with the Agreement.
GREENGUARD Gold Certification Criteria for Building Products and Interior Finishes
Criteria CAS NumberMaximum Allowable
Predicted Concentration Units
TVOC (A) - 0.22 mg/m³
Formaldehyde 50-00-0 9 (7.3 ppb) µg/m³
Total Aldehydes (B) - 0.043 ppm
4-Phenylcyclohexene 4994-16-5 6.5 µg/m³
Particle Matter less than 10 µm (C) - 20 µg/m³
1-Methyl-2-pyrrolidinone (D) 872-50-4 160 µg/m³
Individual VOCs (E) -1/2 CREL
or1/100th TLV
-
(A) Defined to be the total response of measured VOCs falling within the C6 – C16 range, with responses calibrated to a toluene surrogate. Maximum allowable predicted TVOC concentra�ons for GREENGUARD Gold (0.22 mg/m³) fall in the range of 0.5 mg/m³ or less, as specified in CDPH Standard Method v1.2.
(B) The sum of all measured normal aldehydes from formaldehyde through nonanal, plus benzaldehyde, individually calibrated to a compound specific standard. Heptanal through nonanal are measured via TD/GC/MS analysis and the remaining aldehydes are measured using HPLC/UV analysis.
(C) Par�cle emission requirement only applicable to HVAC Duct Products with exposed surface area in air streams (a forced air test with specific test method) and for wood finishing (sanding) systems.
(D) Based on the CA Prop 65 Maximum Allowable Dose Level for inhala�on of 3,200 μg/day and an inhala�on rate of 20 m³/day
(E) Allowable levels for chemicals not listed are derived from the lower of 1/2 the California Office of Environmental Health Hazard Assessment (OEHHA) Chronic Reference Exposure Level (CREL) as required per the CDPH/EHLB/Standard Method v1.2 and BIFMA level credit 7.6.2 and 1/100th of the Threshold Limit Value (TLV) industrial work place standard (Reference: American Conference of Government Industrial Hygienists, 6500 Glenway, Building D-7, and Cincinna�, OH 45211-4438).
P lace and date:
For the issuing office: Seoul 19 June, 2018 DNV GL- Business Assurance
18F, Kyobo Bldg., 1, Jongro, JongnoguSeoul, Korea
In-Kyoon AhnManagement Representative
Lack of fulfilment of conditions as set out in the Certification Agreement may render this Certificate invalid. DNV GL Business Assurance Korea Ltd is accredited by Korea Accreditation Board (KAB) as a Quality Management System certification body (Accreditation number: KAB-QC-10). ACCREDITED UNIT: DNV GL Business Assurance Korea Ltd, 18F Kyobo Bldg., 1 Jong-ro, Jongno-gu, Seoul, Republic of Korea. TEL:+82 2 724 8413. dnvgl.co.kr/assurance
C ertificate No: 76730-2010-AQ-KOR-KAB
Initial certification date: 25 May, 2010
V alid: 18 June, 2018 - 18 June, 2021
This is to certify that the management system of
Lotte Advanced Materials Co., Ltd. 334-27, Yeosusandan-ro, Yeosu-si, Jeollanam-do, Korea and the sites as mentioned in the appendix accompanying this certificate has been found to conform to the Quality Management System standard: ISO 9001:2015, KS Q ISO 9001:2015
This certificate is valid for the following scope: Design, Development and Manufacture of ABS(ACRYLONITRILE BUTADIENE STYRENE), EP(ENGINEERING PLASTIC), PS(POLYSTRENE), SAN(STYRENE ACRYLONITRILE), EPS(EXPANDABLE POLYSTYRENE), SS(SOLID SURFACE), S&B(SINK & BOWL), PC(POLYCARBONATE) and QS(QUARTZ SURFACE).
C ertificate No: 76730-2010-AQ-KOR-KAB P lace and date: Seoul 19 June, 2018
Lack of fulfilment of conditions as set out in the Certification Agreement may render this Certificate invalid. DNV GL Business Assurance Korea Ltd is accredited by Korea Accreditation Board (KAB) as a Quality Management System certifica tion body (Accreditation number: KAB-QC-10). ACCREDITED UNIT: DNV GL Business Assurance Korea Ltd, 18F Kyobo Bldg., 1 Jong-ro, Jongno-gu, Seoul, Republic of Korea. TEL:+82 2 724 8413. dnvgl.co.kr/assurance
Page 2 of 2
Appendix to Certificate Lotte Advanced Materials Co., Ltd. Locations included in the certification are as follows:
Site Name Site Address Site ScopeLotte Advanced Materials Co., Ltd. Yeosu Plant
334-27, Yeosusandan-ro, Yeosu-si, Jeollanam-do, Korea
Manufacture of ABS(ACRYLONITRILE BUTADIENE STYRENE), EP(ENGINEERING PLASTIC), PS(POLYSTRENE), SAN(STYRENE ACRYLONITRILE), EPS(EXPANDABLE POLYSTYRENE), SS(SOLID SURFACE), S&B(SINK & BOWL), PC(POLYCARBONATE) and QS(QUARTZ SURFACE).
Lotte Advanced Materials Co., Ltd. Uiwang HQ & R&D Center
56, Gosan-ro, Uiwang-si, Gyeonggi-do, Korea
Design, Development of ABS(ACRYLONITRILE BUTADIENE STYRENE), EP(ENGINEERING PLASTIC), PS(POLYSTRENE), SAN(STYRENE ACRYLONITRILE), EPS(EXPANDABLE POLYSTYRENE), SS(SOLID SURFACE), S&B(SINK & BOWL), PC(POLYCARBONATE) and QS(QUARTZ SURFACE).
Copyright ⓒ LOTTE ADVANCED MATERIALS CO., LTD. All rights reserved. www.staron.com.au
TECHNICAL BULLETIN
SN-101-2016
Performance Properties - American Standard
STARON®
The information contained herein is provided by LOTTE ADVANCED MATERIALS and its subsidiaries and affiliates (collectively
referred to as “LOTTE ADVANCED MATERIALS”) for information purposes only and should be used by individuals with technical
experience and knowledge in the area. LOTTE ADVANCED MATERIALS does not make any representation or warranties of the
usefulness or expected result of the information, and does not assume any responsibility whatsoever related to the use of the
information. Exclusion of the implied warranties may not apply in certain jurisdictions.
PROPERTIES TYPICAL RESULTS TEST PROCEDURE
Tensile strength 6,000 psi ASTM D 638
Tensile modulus 600,000 psi ASTM D 638
Flexural strength 10,000 psi ASTM D 790
Flexural modulus 1,000,000 psi ASTM D 790
Elongation 0.50% ASTM D 638
Hardness 92 Rockwell “M” Scale
65 Barcol Impressor
ASTM D 785
ASTM D 2583
Thermal expansion 2.0 x 10-5 in/in F˚ ASTM D 696
Gloss (60 Gardner) Between 5 - 20 NEMA LD-3
Color stability No change-200hrs NEMA LD-3
Stain resistance Pass Rating 41 ANSI Z 124
Abrasion resistance Pass ANSI Z 124
Boiling water surface resistance No effect NEMA LD-3
High temperature resistance No effect NEMA LD-3
IZOD Impact resistance (notched) 0.28 ft.lbf/in ASTM D 256
Ball drop 1/2”
(12.3 mm) sheet 144” w/ 1/2 lb ball, No failure NEMA LD-3
Fungi and Bacterial resistance No growth ASTM G 21, G22
Specific gravity
Solid colors
Patterened colors
1.72
1.69
ASTM D 792
Water absorption 0.04%, (1/2”, 24hrs)
0.11%, (1/8”, 24hrs) ASTM D 570
Flammability
Flame spread
Smoke density
Class A / Class 1
10
10
UBC 8-1
ASTM E 84
ASTM E 84
Radiant heat resistance No visual effect NEMA LD-3
Toxicity 84.4g (Solid Color)
81.8g (Patterned Color)
Pittsburgh Test Protocol
(LC50 Test)
This Technical Bulletin is intended to provide guidelines for optimal fabrication, installation, and performance of LOTTE ADVANCED MATERIALS
products mentioned. Though the information contained herein is deemed reliable, none of the contents--including but not limited to the instructions,
techniques, graphics, and recommendations--is to be understood as implying legal liability of fitness for a specific purpose, any other type of warranty, or
being complete or absolute in its range and nature of information.
Depending on the user's particular application, all necessary measures must be taken to verify and test the adequacy for such needs or application. Any
information or recommendation herein is strictly for purposes of reference and as such, LOTTE ADVANCED MATERIALS assumes no responsibility for
its suitability or accuracy or the use of such information for products other than LOTTE ADVANCED MATERIALS Staron® solid surfaces & Radianz®
quartz surfaces.
Copyright ⓒ LOTTE ADVANCED MATERIALS CO., LTD. All rights reserved. www.staron.com.au
TECHNICAL BULLETIN
SN-101-2016
Performance Properties - American Standard
TEMPEST®
The information contained herein is provided by LOTTE ADVANCED MATERIALS and its subsidiaries and affiliates (collectively
referred to as “LOTTE ADVANCED MATERIALS”) for information purposes only and should be used by individuals with technical
experience and knowledge in the area. LOTTE ADVANCED MATERIALS does not make any representation or warranties of the
usefulness or expected result of the information, and does not assume any responsibility whatsoever related to the use of the
information. Exclusion of the implied warranties may not apply in certain jurisdictions.
PROPERTIES TYPICAL RESULTS TEST PROCEDURE
Tensile strength 3,500 psi ASTM D 638
Tensile modulus 786,000 psi ASTM D 638
Flexural strength 6,500 psi ASTM D 790
Flexural modulus 950,000 psi ASTM D 790
Elongation 0.50% ASTM D 638
Hardness 88 Rockwell “M” Scale
54 Barcol Impressor
ASTM D 785
ASTM D 2583
Thermal expansion 2.3 x 10-5 in/in F˚
3.6 x 10-5 m/m °C ASTM D 696
Gloss (60 Gardner) Between 10 - 75 NEMA LD-3
Color stability Pass NEMA LD-3
Stain resistance Pass ANSI Z 124
Cleanability & Wear Pass ANSI Z 124
Boiling water surface resistance No effect NEMA LD-3
High temperature resistance No effect NEMA LD-3
IZOD Impact resistance (notched) 0.28 ft.lbf/in ASTM D 256
Ball drop 1/2”
(12.3 mm) sheet
1/2 lb ball
No failure, 93+ NEMA LD-3
Fungi and Bacterial resistance No growth ASTM G 21, G22
Specific gravity 1.6 ASTM D 792
Water absorption 0.04%, (1/2”, 24hrs) ASTM D 570
Flammability Class A / Class 1 ASTM E 84 / UBC 8-1
Food Equipment Materials Approved NSF/ANSI 51 (Food Zone)
This Technical Bulletin is intended to provide guidelines for optimal fabrication, installation, and performance of LOTTE ADVANCED MATERIALS
products mentioned. Though the information contained herein is deemed reliable, none of the contents--including but not limited to the instructions,
techniques, graphics, and recommendations--is to be understood as implying legal liability of fitness for a specific purpose, any other type of warranty, or
being complete or absolute in its range and nature of information.
Depending on the user's particular application, all necessary measures must be taken to verify and test the adequacy for such needs or application. Any
information or recommendation herein is strictly for purposes of reference and as such, LOTTE ADVANCED MATERIALS assumes no responsibility for
its suitability or accuracy or the use of such information for products other than LOTTE ADVANCED MATERIALS Staron® solid surfaces & Radianz®
quartz surfaces.
1/6
○ Manufactrue
○ Supplier
- Not Classified
- The hazards of this product are associated with its fabrication. Such as sawing, routing and sanding can generate dust.
- Exposure to high concentration of dust or inhalation may cause respiratory irritation and sneeze. This information is according
to exposure limits of PMMA (Poly methyl matacrylate).
- Pictogram
none
- Signal word
none
- Hazard statement
none
- Precautionary statement
Prevention: Not Applicable, Respnse: Not Applicable, Storage: Not Applicable, Disposal: Not Applicable
- NFPA rating
Health : Not applicable, Flammability : Not applicable, Reactivity : Not applicable
2.2 Label elements
- FAX No. : +82-31-596-3882
2. HAZARD IDENTIFICATION
2.1 Classification of the substance or mixture
- Department : Technical Solution Team
- Telephone : +82-31-596-3861
- Emergency telephone : +82-31-596-3861
- Address : 56, Gosan-ro, Uiwang-si, Gyeonggi-do, Republic of Korea
- Telephone : +82-61-689-1151
- Emergency telephone : +82-61-689-1151
- FAX No. : +82-61-689-1759
- uses advised against
- Name of Supplier : LOTTE ADVANCED MATERIALS
: Do NOT use with strong acid or base chemicals
- Department : Development Team
Material Safety Data Sheet (MSDS)
STARON Solid Surface
Date of issue: 2010-10-04 Revision data : 2018-05-11 Version:
1. PRODUCT AND COMPANY IDENTIFICATION
1.1 Product Name
1.3 Detail of the supplier of the safety data sheet
- Name of Supplier : LOTTE ADVANCED MATERIALS
- Address : 334-27, Yeosusandan-ro, Yeosu-si, Jeollanam-do, Republic of Korea
- Staron solid surface
1.2 Product use
- Application : Kitchen top, counter top, interior wall, ect.
2/6
- At room temperature, it does not have gas emissions. But under high temperature condition, small amount of acryl gas may be emitted.
Depending on time and temperature, the gas emission amount will be affected. The acryl gas may cause irritation or allergy on eye,
nose, skin and neck. Repeated and high concentrated exposure may cause headache, vomiting and bronchoalveolar inflammation.
Concentration
range(%)
40 - 45 %
55 - 60 %
< 1 %
< 1 %
7. HANDLING AND STORAGE
7.1. Precautions for safe handling
- When fabricating such as thermoforming, cutting and sanding, wear a proper protective gears.
7.2. Conditions for safe storage, including any incompatibilities
- Store in 15~23℃ temp. and dry condition inside or warehouse on flat ground.
- Large amount: Avoid generating dust in the air. Cleaning dust using vacuum cleaner and keep it into dry container.
6.2. Environmental precautions
- AIR: Avoid generation of dust and fine dust dispersed in the air
6.3. Methods and material for containment and cleaning up
- Small amount: Brush into dry container or bag.
-- Protective fire fighting clothing (including fire fighting helmet, coat, pants, boots and glove), Air supplied respirator.
6. ACCIDENTAL RELEASE MEASURES
6.1. Personal precautions, protective equipment and emergency procedures
- Proper personal protective equipment should be utilized when handling this material.
- Unsuitable extinguishing media : Not available
5.2 Special hazards arising from the substance or mixture
- Hazardous Product of Combustion: Carbon Oxides (CO, CO2), Various Hydrocarbons.
5.3 Advice for fire-fighters
5. FIRE FIGHTING MEASURES
5,1 Extinguishing Media
- Suitable extinguishing media : Dry chemical, carbon oxide, water spray and foam
4.3 Inhalation
- If breathing is difficult, remove victim to fresh air and keep at rest in a position comfortable for breathing. Follow instruction of doctor.
4.4 Ingestion
- If vomitting, rinse mouth and follow instruction of doctor.
4.2 Skin Conatact
- No hazard. Wash with soap and water.
Pigment Pigment Trade secret
Additives Additives
Aluminum Trihydrate ATH 21645-51-2
4. FIRST AID MEASURES
4.1 Eye Contact
- Rinse thoroughly with plenty of water for over 15 minute and call a doctor immidiately.
2.3. Other hazards
3. COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Usual Name CAS No.
- Risk of Explosion or Fire: Staron solid surface has fire resistance but it has small risk of fire when it exposure to heat or fire.
Trade secret
ACRYLIC POLYMER PMMA 9011-14-7
3/6
○ Respiratory protection
○ Eye Protection
○ Hand Protection
○ Skin protection
10. STABILITY AND REACTIVITY
10.1 Stability and Possibility of Hazardous Reaction
- Stability : Stable under room temperature and normal pressure
- Possibility of Hazardous Reaction: When cutting by saw or router, friction heat reach up to 300℃ temperature.
10.2 Conditions to avoid
- Avoid extreme heat
9.17 Decomposition No data
9.18 Viscosity Not applicable
9.19 Explosive properties No data
9.14 Relative density 1.6 ~ 1.8
9.15 Partition coefficient No data
9.16 Autoignition Temperature No data
9.11 Vapour pressure Not applicable
9.12 Water Solubility Not soluble in water
9.13 Vapour density Not applicable
9.8 Evaporation rate Not applicable
9.9 Flammability (solid, gas) Not applicable
9.10 Upper/lower flammability or explosive limits Not applicable
Not applicable
9.5 Boiling /Freezing point Not applicable
9.6 Boiling point/boiling range Not applicable
9.7 Flash point No data
- Physical state Solid (Sheet form)
- Color Various
9.2 Odor Minimal
9.3 Odor Threshold Not applicable
9.4 pH
8.1. Control parameters
- Occupational Exposure Limits : Not available
8.2 Appropriate engineering controls
- Not available
8.3 Individual protection measures, such as personal protective equipment
- Dust mask when exposure on high concentration of dust
* ACGIH = American Conference of Governmental Industrial Hygienists
- TWA : Not available
- STEL : Not available
- 0.3mg/㎥ OSHA TWA(Inhalable particles): Not available
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
- 0.1mg/㎥ OSHA TWA(Respirable particles): Not available
- ACGIH : Not available
- Biological exposure limit : Not available
- Wear safely glasses
Methyl methacrylate monomer may be released. Dust may be flashed under ignition temp
- protectieve clothing
- Wear protective gloves
9. Physical and chemical properties
9.1 Appearance
4/6
○ (Respratory system)
○ (ingestion)
○ (Eye, Skin)
○ Acute toxicity:
* Oral
* Dermal
* Inhalation
○ Skin corrosion/irritation
○ Eye corrosion/irritation
○ Respiratory sensitization
○ Skin Sensitization
○ Carcinogenic
○ Germ cell mutations
○ Reproductive toxicity
○ Specific target organ toxicity(single exposure)
○ Specific target organ toxicity(repeated exposure)
○ Aspiration hazard
[PMMA]
○ TLV-TWA =100ppm =410mg/m3 :ACGIH (1991-2
○ LD50/Oral/Rat =7,872mg/kg :RTECS, 47796
○ MMA contents may leave on cutting tool blade about 100ppm TLV. Ventilation will dilute the concentration.
○ Fish
12. ECOLOGICAL INFORMATION
12.1. Ecotoxicity
- Not available
- Not available
11.3. TOXICALOGICAL EFFECTS
- No data
- Not available
- Not available
- Not available
- Not available
- Not available
- Acute exposure : High concentration may cause difficulty with physical breathing.
- Not available
- Chronic overexposure: Not available
- Chronic overexposure: Not available
- Not available
- Not available
- :High concentration may cause difficulty with breathing.
- Organic reaction with digestive organs may cause irritation.
- Particles may cause irritation.
11.2. Toxicity and irritation
- Acute exposure : Organic reaction with digestive organs may cause irritation.
- Acute exposure : Particles may cause irritation.
- Chronic overexposure: Not available
10.3 Materials to avoid
- Acids, base, solvent, heat, spark, flame
10.4 Hazardous decomposition products
- Carbon oxides, Methyl methacrylate monomer, smog.
11. TOXICOLOGICAL INFORMATION
11.1 Information on toxicological effects
5/6
○ Invertebrate
○ Algae
- Persistence : No data
- Degradability : No data
- Biodegradablility: No data
- Bioaccumulation: No data
15.1. Occupation safety and health acts
- Not available
15.3. Safety control of dangerous substances Act
15.2. Chemical Safety Assessment
- Not applicable
14.5. Environmental hazards
- Not available
14.6 Special precautions for user related to transport or transportation measures
- Not available
15. REGULATORY INFORMATION
- Not applicable
14.2 UN proper shipping name
- Not applicable
14.3 Transport hazard class(es)
- Not applicable
14.4 Packing group
- All disposal methods must be in compliance with all Federal, State/Provincial and local laws and regulations
13.2 Requore attention
- The user of this product must properly characterize the waste/ container generated from the use of this product in accordance with all applicable
federal, state and/or lacal laws and regulations in oerder to determine the proper disposal of the waste in accordance with all applicable federal,
state and/ or local laws and regulations
- Dispose of waste in accordance with local regulation
14. TRANSPORTATION INFORMATION
14.1 UN number
12.4. Mobility in soil
- Not available
12.5 Other adverse effects
- Not available
13. DISPOSAL CONSIDERATIONS
13.1 Waste treatment methods
- No data
- No data
12.2 Persistence/degradability
12.3 Bioaccumulative potential
- Not available
6/6
○ Persistent Organic Pollutants Control Act
○ EU
* Confirm classific result : Not classified
* Harzard words Not applied
* Prevention measure: Not applied
○ U.S regulations
* OSHA Hazard Communication Standard (29 CFR 1910.119)
* CERCLA 103 (40CFR302.4)
* EPCRA 302 (40CFR355.30)
* EPCRA 304 (40CFR355.40)
* EPCRA 313 (40CFR372.65)
○ Rotterdam convention material
○ Stockholm convention material
○ Montreal Protocol material
○ TSCA (US Toxic Substances Control Act): In compliance with TSCA Inventory requirements for commercial purposes
16.1 Sources of Data
16.4 Others
16.2 Creation Date
- 2010-10-04
16.3 Number of Revision and Latest Revisioni Date
-6th : 2018.05.11
- Not applicable
- Not applicable
- Not applicable
- Not applicable
- Not applicable
16. OTHER INFORMATION
- Not available
15.5. Foreign legal
- Not available
- Not applicable
- Not applicable
- Not applicable
- Not available
15.4. Wastes control Act
BẢNG HƯỚNG DẪN AN TOÀN VẬT LIỆU (MSDS)
STARON Solid Surface
4 tháng 10 năm 2010 Ngày nâng cấp dữ liệu: 11 tháng 5 năm 2018
1. SẢN PHẨM VÀ THÔNG TIN NHÀ SẢN XUẤT
1.1 Tên sản phẩm
Đá Solid surface thương hiệu Staron 1.2 Sử dụng sản phẩm Ứng dụng: Mặt bếp, mặt bàn, tường nội thất, ect. Chống chỉ định: Không sử dụng với hóa chất axit hoặc hóa chất mạnh. 1.3 Chi tiết về nhà cung cấp bảng dữ liệu an toàn
o Thông tin nhà sản xuất - Tên : LOTTE ADVANCED MATERIALS - Địa chỉ : 334-27, Yeosusandan-ro, Yeosu-si, Jeollanam-do - Xuất xứ : Hàn Quốc - Bộ phận quản lý : Phòng Phát triển (Development Team) - Điện thoại : + 82-61-689-1151 - FAX : + 82-61-689-1759 o Thông tin nhà phân phối : - Tên : SAMSUNG INTERIOR - Địa chỉ : 19W Nguyễn Hữu Cảnh – Bình Thạnh - HCM - Bộ phận quản lý : Samsung Interior - Điện thoại : 028 3 7447 333 - 090 2580 097
2. CẢNH BÁO NGUY HIỂM
2.1 Phân loại chất hoặc hỗn hợp - Các mối nguy hiểm của sản phẩm này có liên quan đến việc gia công nó. Chẳng hạn như cưa, định tuyến
và chà nhám có thể tạo ra bụi.
- Tiếp xúc với nồng độ cao của bụi hoặc hít phải có thể gây kích ứng đường hô hấp và hắt hơi. Thông tin
này dựa trên bảng tính phơi nhiễm của PMMA (Poly methyl methacrylate).
2.2 Nhãn dán sản phẩm:
- Hình ảnh: Không - Từ ngữ cảnh báo: Không - Thông báo cảnh báo: Không - Thông báo phòng ngừa: Không - Phòng ngừa: Không - Phản ứng: Không - Bảo quản: Không - Xử lý: Không áp dụng - Xếp hạng NFPA - Ảnh hưởng sức khỏe: Không gây ảnh hưởng sức khỏe - Tính dễ cháy: Không - Độ phản ứng: Không
2.3. Các mối nguy hiểm khác
- Tại nhiệt độ phòng, chất liệu không tạo ra khí thải. Nhưng trong điều kiện nhiệt độ cao, một lượng nhỏ khí acrylic có thể được phát ra.
- Tùy thuộc vào thời gian và nhiệt độ, lượng khí thải sẽ bị ảnh hưởng. Khí acrylic có thể gây kích ứng hoặc dị ứng trên mắt, mũi, da và cổ. Phơi nhiễm liên tục và tập trung cao có thể gây đau đầu, nôn mửa và viêm phế quản.
3. THÔNG TIN VỀ THÀNH PHẦN HÓA HỌC
Tên chất hóa học Tên thường dùng CAS No. Phạm vi nồng độ (%) ACRYLIC POLYMER PMMA 9011-14-7 40 - 45 % Aluminum Trihydrate ATH 21645-51-2 55 - 60 % Hạt màu Hạt màu Trade secret < 1 % Phụ gia Phụ gia Trade secret < 1 %
4. CÁC BIỆN PHÁP XỬ LÝ ĐẦU TIÊN KHI CÓ SỰ CỐ XẢY RA 4.1 Tiếp xúc với mắt
- Rửa kỹ với nước trong ít nhất 15 phút và gọi bác sĩ ngay lập tức.
4.2 Tiếp xúc da - Không nguy hiểm. Rửa bằng xà phòng và nước.
4.3 Hít phải - Nếu thở khó khăn, hãy đưa nạn nhân ra nơi thoáng khí và giữ yên ở tư thế thoải mái để thở. Làm theo
chỉ dẫn của bác sĩ.
4.4 Nuốt phải - Nếu nôn, súc miệng và làm theo chỉ dẫn của bác sĩ.
5. BIỆN PHÁP XỬ LÝ KHI CHÁY NỔ
5.1 Phương tiện chữa cháy - Các phương tiện chữa cháy phù hợp: Hóa chất khô, oxit carbon, xịt nước và bọt - Phương tiện chữa cháy không phù hợp: Không áp dụng
5.2 Các mối nguy hiểm đặc biệt phát sinh từ các chất hoặc hỗn hợp
- Sản phẩm nguy hiểm của quá trình đốt cháy: Carbon Oxide (CO, CO2), Hydrocarbon khác nhau. - Nguy cơ nổ hoặc cháy: Đá Solid surface Staron có khả năng chống cháy nhưng nó có rủi ro cháy nhỏ khi
tiếp xúc với nhiệt hoặc lửa.
6. CÁC BIỆN PHÁP ĐƯỢC KHUYẾN NGHỊ
6.1. Phòng ngừa cá nhân, thiết bị bảo vệ và quy trình khẩn cấp - Thiết bị bảo vệ cá nhân: Sử dụng các sản phẩm chuyên dụng khi xử lý vật liệu này.
6.2. Phòng ngừa môi trường - Mục đích: Tránh phát sinh bụi và bụi mịn phát tán trong không khí
6.3. Phương pháp và vật liệu để ngăn chặn rò rỉ và phương pháp tẩy rửa làm sạch - Số lượng nhỏ: Thu vào hộp hoặc túi khô. - Số lượng lớn: Tránh tạo ra bụi trong không khí. Làm sạch bụi bằng máy hút bụi và giữ nó trong thùng
chứa
7. VẬN CHUYỂN VÀ BẢO QUẢN
7.1. Thận trọng để xử lý an toàn
- Khi chế tạo như tạo hình, cắt và chà nhám, mặc một bánh răng bảo vệ thích hợp.
7.2. Điều kiện để cất giữ an toàn - Lưu trữ trong nhiệt độ 15 ~ 23 ° C và điều kiện khô bên trong hoặc kho trên mặt đất bằng phẳng.
8. KIỂM SOÁT TIẾP XÚC / BẢO VỆ CÁ NHÂN 8.1. Thông số điều khiển
- Giới hạn phơi nhiễm nghề nghiệp: Không áp dụng - TWA: Không áp dụng - STEL: Không áp dụng - 0,3mg / m3 OSHA TWA (Các hạt có thể hít vào): Không áp dụng - 0,1mg / m3 OSHA TWA (Các hạt có thể hô hấp): Không áp dụng - ACGIH: Không áp dụng - Giới hạn phơi nhiễm sinh học: Không có sẵn
* ACGIH = Hội nghị vệ sinh công nghiệp chính phủ Mỹ
8.2 Kiểm soát kỹ thuật phù hợp: - Không áp dụng
8.3 Các biện pháp bảo vệ cá nhân, như thiết bị bảo vệ cá nhân - Bảo vệ hô hấp: Mặt nạ chống bụi khi tiếp xúc với bụi nồng độ cao - Bảo vệ mắt: Đeo kính an toàn - Bảo vệ tay: Đeo găng tay bảo vệ - Bảo vệ da: Bảo vệ quần áo
9. Tính chất vật lí và hóa học
9.1 Hình thức
- Trạng thái vật lý Chất rắn (Dạng tấm) - Màu sắc Khác nhau
9.2 Mùi Tối thiểu 9.3 Ngưỡng mùi Không áp dụng 9.4 pH Không áp dụng 9.5 Điểm sôi / Điểm đóng băng Không áp dụng 9.6 Điểm sôi / Phạm vi sôi Không áp dụng 9.7 Điểm chớp cháy: Không áp dụng 9.8 Tốc độ bay hơi: Không áp dụng 9.9 Tính dễ cháy (rắn, khí): Không áp dụng 9.10 Giới hạn dễ cháy trên / dưới hoặc giới hạn nổ Không áp dụng 9.11 Áp suất hơi: Không áp dụng 9.12 Độ hòa tan trong nước Không tan trong nước 9.13 Mật độ hơi Không áp dụng 9.14 Mật độ tương đối 1.6 ~ 1.8 9.15 Hệ số phân vùng Không có dữ liệu 9.16 Nhiệt độ tự động Không có dữ liệu 9.17 Phân hủy Không có dữ liệu 9.18 Độ nhớt Không áp dụng 9.19 Thuộc tính nổ Không có dữ liệu
10. ĐỘ ỔN ĐỊNH VÀ PHẢN ỨNG
10.1 Tính ổn định và khả năng của phản ứng nguy hiểm - Ổn định: Ổn định dưới nhiệt độ phòng và áp suất bình thường - Khả năng phản ứng nguy hiểm: - Khi cắt bằng cưa hoặc thiết bị định tuyến, nhiệt ma sát đạt tới nhiệt độ 300°C.
- Methyl methacrylate monomer có thể phát tán ra không khí. Bụi có thể bị lóe lên dưới nhiệt độ đánh lửa.
10.2 Điều kiện cần tránh - Tránh nhiệt độ quá cao
10.3 Vật liệu cần tránh - Axit, bazơ, dung môi, nhiệt, tia lửa, ngọn lửa
10.4 Sản phẩm phân hủy nguy hiểm - Oxit carbon, monomer Methyl methacrylate, sương mù.
11. THÔNG TIN ĐỘC TÍNH
11.1 Thông tin về tác dụng độc hại o Hệ hô hấp: Nồng độ cao có thể gây khó thở. o Tiêu hóa: Phản ứng hữu cơ với các cơ quan tiêu hóa có thể gây kích ứng. o Mắt, da: Các hạt có thể gây kích ứng.
11.2. Độc tính và kích ứng o Độc tính cấp tính:
* Đường uống - Cấp tính: Phản ứng hữu cơ với các cơ quan
tiêu hóa có thể gây kích ứng. - Phơi nhiễm mãn tính: Không áp dụng
*Tiếp xúc da
- Tiếp xúc cấp tính: Các hạt có thể gây kích ứng - Tiếp xúc quá mức mãn tính: Không áp dụng
* Hít phải
- Tiếp xúc cấp tính: Nồng độ cao có thể gây khó thở
- Tiếp xúc quá mức mãn tính: Không có sẵn
o Ăn mòn / kích ứng da - Không áp dụng
o Ăn mòn / kích ứng mắt
- Không áp dụng
o Nhạy cảm hô hấp
- Không áp dụng
o Nhạy cảm với da - Không áp dụng
o Gây ung thư
- Không áp dụng
o Đột biến tế bào mầm - Không áp dụng - o Độc tính sinh sản
- Không áp dụng
o Độc tính cơ quan đích cụ thể (phơi nhiễm đơn)
- Không áp dụng
o Độc tính cơ quan đích cụ thể (tiếp xúc nhiều lần)
- Không áp dụng
11.3 Độc lực [PMMA]
o TLV-TWA = 100ppm = 410mg / m3: ACGIH (1991-2) o LD50 / Uống / Chuột = 7,872mg / kg: RTECS, 47796 o Hàm lượng MMA có thể để lại trên lưỡi dao công cụ khoảng 100ppm TLV. Thông gió sẽ làm loãng nồng
độ.
12. TÁC ĐỘNG SINH THÁI
12.1. Độc tính sinh thái - Cá: Không có dữ liệu - Động vật không xương sống: Không có dữ liệu
- Tảo: Không có dữ liệu
12.2 Độ bám dính / Phân hủy - Kiên trì: Không có dữ liệu - Phân hủy: Không có dữ liệu
12.3 Tiềm năng tích lũy sinh học - Khả năng phân hủy sinh học: Không có dữ liệu - Tích lũy sinh học: Không có dữ liệu
12.4. Tính di động trong đất - Không có sẵn
12.5 Tác dụng phụ khác: - Không áp dụng
13. TƯ VẤN TRANH CHẤP
13.1 Phương pháp xử lý chất thải - Tất cả các phương pháp xử lý phải tuân thủ tất cả các luật và quy định của Liên bang, Tiểu bang / Tỉnh
và địa phương nơi sử dụng.
13.2 Yêu cầu sự chú ý - Người sử dụng sản phẩm này phải mô tả đúng chất thải / thùng chứa được tạo ra từ việc sử dụng sản
phẩm này theo tất cả các luật và quy định hiện hành của liên bang, tiểu bang và / hoặc địa phương để xác định việc xử lý chất thải phù hợp theo tất cả các quy định hiện hành luật và quy định của liên bang, tiểu bang và / hoặc địa phương
- Xử lý chất thải theo quy định của địa phương
14. THÔNG TIN VẬN TẢI 14.1 Số UN
- Không áp dụng
14.2 Tên vận chuyển thích hợp của Liên Hợp Quốc - Không áp dụng
14.3 Lớp nguy hiểm vận chuyển - Không áp dụng
14.4 Nhóm đóng gói - Không áp dụng
14.5. Mối nguy hiểm môi trường - Không có
14.6 Các biện pháp phòng ngừa đặc biệt cho người dùng liên quan đến các biện pháp vận chuyển hoặc vận chuyển
- Không có
15. THÔNG TIN QUY ĐỊNH 15.1. An toàn và sức khỏe nghề nghiệp
- Không áp dụng
15.2. Đánh giá an toàn hóa chất - Không áp dụng
15.3. Kiểm soát an toàn các chất nguy hiểm Đạo luật - Không áp dụng
15.4. Đạo luật kiểm soát chất thải: - Không áp dụng
15.5. Pháp luật nước ngoài ○ Đạo luật kiểm soát chất ô nhiễm hữu cơ lâu dài: Không có sẵn ○ EU
- Xác nhận kết quả phân loại: Không được phân loại - Từ ngữ cảnh báo: Không áp dụng - Biện pháp phòng ngừa: Không áp dụng
○ Đạo luật Mỹ
- OSHA Hazard Communication Standard (29 CFR 1910.119) - Không áp dụng - CERCLA 103 (40CFR302.4) - Không áp dụng - EPCRA 302 (40CFR355.30) - Không áp dụng - EPCRA 304 (40CFR355.40) - Không áp dụng - EPCRA 313 (40CFR372.65) - Không áp dụng
○ Tài liệu tham khảo Hội Nghị Rotterdam
- Không áp dụng ○ Tài liệu tham khảo Hội Nghị Stockholm
- Không áp dụng ○ Tài liệu Nghị định thư Montreal
- Không áp dụng ○ TSCA (Đạo luật kiểm soát chất độc hại của Hoa Kỳ):
- Tuân thủ các yêu cầu TSCA Hàng tồn kho cho mục đích thương mại
16. THÔNG TIN KHÁC 16.1 Nguồn dữ liệu
16.2 Ngày khởi tạo: 4 tháng 10 năm 2010
16.3 Số lần sửa đổi và ngày sửa đổi mới nhất 11 tháng 5 năm 2018
16.4 Thông tin khác
www.staron.comCopyright ⓒ Lotte Chemical Corp. All rights reserved.
WARRANTY
RESIDENTIAL10-YEAR LIMITED
WARRANTY
Permanently installed Staron Solid Surfaces sheets and shapes Lotte Chemical Corp. to the original owner. Staron
Solid Surfaces must be fabricated and installed by Staron certified Fabricator/Installer, used and maintained in
accordance with instructions provided by Lotte Chemical Corp.. Lotte Chemical Corp. at its sole option will repair or
replace, without charge, such Product if it fails due to a manufacture defect during the first ten (10) years after the date of
initial installation. This includes necessary real cost charges needed to repair or replace the Product. Although Lotte
Chemical Corp. shall make its best effort to repair or replace with the best possible color match to the original as possible,
Lotte Chemical Corp. cannot guarantee the exact color in the event of repair or replacement. All instructions for filling a
claim under this limited warranty are available from your dealer and fabrication/installation source or by contacting Lotte
Chemical Corp. directly.
This limited warranty is transferable during the 10-year period following initial installation only when the new owner notifies
Lotte Chemical Corp. in writing.
This warranty excludes the following:
Lotte Chemical Corp.’s obligation hereunder is limited solely to the repair or replacement including necessary reasonable
real cost charges of the Products purchased hereunder. Except as to what is stated in this limited warranty herein, Lotte
Chemical Corp. makes no warranties, express or implied, in respect to the Product, including, but not limited to, any
implied warranty of merchantability or fitness for a particular purpose, and all such warranties hereby are expressly
disclaimed. Lotte Chemical Corp. does not warrant that the Product will meet the end users’ requirements. Lotte Chemical
Corp. shall not be liable for incidental, consequential, indirect, special, punitive, or exemplary damages of any kind,
including lost good will, lost profits, lost business, or other indirect economic damages, and further including injury to
property, whether such claim is based on theories of contract, negligence, tort (including strict liability) or otherwise, as a
result of breach of any warranty regardless of whether Lotte Chemical Corp. was advised, had other reason to know, or in
fact knew of the possibility of such damages.
SOME COUNTRIES, STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION STATED
ABOVE, SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS, WHICH WILL VARY FROM
COUNTRY TO COUNTRY, STATE TO STATE OR PROVINCE TO PROVINCE
Effective as September, 2015
01. Minor conditions such as stains, scratches, water spots and
burns;
02. Failure to comply with Lotte Chemical Corp.’s instructions
including
fabrication, installation, care, maintenance, etc;
03. Any products moved from their original place of installation;
04 Seam appearance of any adhesive, caulk or other accessory
items;
05. Color variation from the sample;
06. Color variation within different lots;
07. Exact color match as a result of Product replacement or
repair is not guaranteed;
08. Failure caused by other substructure support;
09. Misuse, abuse (including impact damage and contact with
chemical reagents not intended for use with Product);
10. Improper fabrication, installation, handling or maintenance;
11. Damage caused by excessive heat; or by an act of nature;
12. Workmanship of Fabricators or Installers;
13. Damages from other than manufacturing defect;
14. Any Product installed or located outdoors, such as outdoor
kitchens, BBQ work surfaces, or in heated areas such as
saunas, steam rooms, and shower pans;
15. In-Carton products including components made from
Staron® ;
16. Any Product installed in recreational vehicles;
17. Any Product fabricated and installed in commercial
applications;
18. Fabrication, Installation, Modification or Repairs made by
other than Staron® CFI (Certified Fabricator Installer);
19. Same color and veined intensity between sheets in
SUPREME collection. ((Veining may vary from sheet tosheet and also within a sheet. Special consideration has to be taken into any joint and coved up-stands.)
www.staron.comCopyright ⓒ Lotte Chemical Corp. All rights reserved.
WARRANTY
RESIDENTIAL 10-YEAR LIMITED
WARRANTY
This warranty cannot be modified, amended, or in any way altered except by an instrument in writing signed by
an authorized officer of Lotte Chemical Corp..
Effective as September, 2015
Warranty Service:
To request warranty service, contact your original fabricator/installer. You must present the original sales receipt or
produce proof of purchase and installation of Staron® Solid Surfaces, which clearly proves the Product purchase and
date of installation, in order to obtain service under this limited warranty. For more information about this warranty,
please contact to Lotte Chemical Corp. at the address below:
LOTTE Chemical Deutschland GMBHKölner Str. 12 65760 Eschborn, GermanyTEL +49 6196 77 272 75
LOTTE Chemical Thailand Co., Ltd.16th Floor, Empire Tower, Unit 1602-1603, 1 South Sathorn RD,Yannawa, Bangkok, Thailand. 10120Tel. +66-2-624-6737
LOTTE Chemical Deutschland GMBH-REPRESENTATIVE OFFICE(DUBAI)Office No 1702, Arenco Tower, Media City, Dubai, UAE. PO BOX 48969Email [email protected]. +971-4-245-1401~1405
LOTTE Chemical Shanghai Co., Ltd.Rm2701, Shanghai International Trade Center,2201 West Yan An Rd, Shanghai, China. 200336Tel. +86-21-62703000-856
Các tấm đá Solid Surface thương hiệu Staron được lắp đặt và bảo hành bởi LOTTE CHEMICAL. Đá Solid Surface phải
được chế tạo và lắp đặt bởi LOTTE CHEMICAL. Đá Solid Surface được lắp đặt và bảo hành theo hướng dẫn của LOTTE
CHEMICAL. LOTTE CHEMICAL sẽ sửa chữa hoặc thay thế miễn phí các sản phẩm Staron nếu sản phẩm bị lỗi do lỗi sản
xuất trong mười (10) năm đầu tiên sau ngày lắp đặt. Điều này bao gồm chi phí thực tế cần thiết để sửa chữa hoặc
thay thế sản phẩm. Mặc dù LOTTE CHEMICAL sẽ nỗ lực hết sức để sửa chữa hoặc thay thế bằng màu phù hợp nhất
với màu gốc nhất có thể, nhưng LOTTE CHEMICAL không thể đảm bảo màu chính xác trong trường hợp sửa chữa
hoặc thay thế. Nếu khách hàng có yêu cầu bảo hành các sản phẩm Staron, xin liên hệ với đại lý Staron gần nhất, tại
đó bạn sẽ được hướng dẫn cách điền form và những lưu ý cần thiết hoặc liên hệ trực tiếp với LOTTE CHEMICAL.
Bảo hành này có thể được chuyển nhượng trong thời gian 10 năm sau ngày cài đặt ban đầu chỉ khi chủ sở hữu thông
báo bằng văn bản LOTTE CHEMICAL.
Bảo hành này không bao gồm những điều sau đây:
01. Các vấn đề nhỏ như vết bẩn, vết trầy xước, đốm nước và cháy xém.
02. Không tuân thủ hướng dẫn chế tạo, lắp đặt, chăm sóc, bảo trì, vv … của Lotte Chemical Corp
03. Sản phẩm bị di chuyển khỏi vị trí cài đặt ban đầu của chúng
04. Đường chỉ xuất hiện ở bất kỳ mối nối, khe rãnh hoặc các tiếp diện phụ khác của sản phẩm
05. Sự khác biệt màu với mẫu xem trước
06. Sự khác biệt màu sắc giữa các lô hàng khác nhau
07. Màu sắc chính xác phù hợp do việc thay thế hoặc sửa chữa sản phẩm sẽ không được đảm bảo
08. Thiệt hại do sự tác động từ công trình hạng mục khác
09. Sử dụng, lạm dụng (bao gồm cả thiệt hại do va chạm và tiếp xúc với thuốc thử hóa học không được sử
dụng với sản phẩm này)
10. Chế tạo, lắp đặt, xử lý hoặc bảo trì không đúng cách
11. Các thiệt hại gây ra bởi nhiệt độ quá cao; hoặc bằng một hành động bất khả kháng
12. Tay nghề của Người gia công hoặc Trình độ lắp đặt 13. Thiệt hại từ các lỗi khác ngoài sản xuất
14. Bất kỳ sản phẩm nào được lắp đặt ngoài trời, nhà bếp, bề mặt để nướng BBQ hoặc để sưởi ấm các khu
vực như phòng xông hơi, phòng tắm hơi và bệ tắm, bồn tắm
15. Các sản phẩm trong thùng carton bao gồm các thành phần được làm từ Staron Solid Surfaces
16. Bất kỳ sản phẩm nào được lắp đặt trong xe thùng
17. Bất kỳ Sản phẩm nào được chế tạo và lắp đặt trong các ứng dụng thương mại
18. Chế tạo, lắp đặt, sửa đổi hoặc sửa chữa được thực hiện bởi các hãng lắp đặt khác
19. Màu sắc và các đường vân sẽ thay đổi theo từng tấm đá (sự sai lệch do bất cẩn trong lắp đặt vân đá)
CHÍNH SÁCH BẢO HÀNH 10 NĂM CỦA STARON
Trong phạm vi giới hạn bảo hành của tài liệu này, LOTTE CHEMICAL không bảo hành, cho các trường hợp rõ ràng hay
ngụ ý đối với Sản phẩm, bao gồm nhưng không giới hạn, bất kỳ bảo hành nào về tính thương mại hoặc phù hợp cho
một mục đích cụ thể nào hoặc tất cả các bảo hành có tính chất tương tự sẽ bị từ chối rõ ràng bởi LOTTE CHEMICAL.
LOTTE CHEMICAL không đảm bảo rằng sản phẩm sẽ đáp ứng các yêu cầu của người dùng cuối.
LOTTE CHEMICAL sẽ không chịu trách nhiệm cho bất cứ sự cố/ hậu quả gián tiếp/ hậu quả đặc biệt/ trừng phạt hoặc
thiệt hại dưới bất kỳ hình thức nào liên quan đến việc mất thiện chí, phương hại đến lợi nhuận/ việc kinh doanh bị
mất hoặc thiệt hại kinh tế gián tiếp khác. Kể cả những hư hại đối với tài sản dù cho yêu cầu đó dựa trên hợp đồng.
Do sự sơ suất, thiếu trách nhiệm (bao gồm cả trách nhiệm pháp lý) hay nói cách khác bất kỳ vi phạm nào đến cách
thức bảo hành đều bị từ chối dù cho trong thực tế những sự thiệt hại đó đã được dự báo trước.
Một số quốc gia và vùng lãnh thổ không chấp nhận những giới hạn và loại trừ trên. do đó những giới hạn và loại trừ
trên có thể không được áp dụng. giới hạn bảo hành này gửi đến bạn những chỉ dẫn cụ thể hợp pháp. bạn cũng có
thể có những chỉ dẫn hợp lý khác mà những chỉ dẫn này phù hợp trên diện rộng được chấp nhận bởi nhiều quốc gia,
nhiều tỉnh thành.
Dịch vụ bảo hành:
Để yêu cầu dịch vụ bảo hành, liên hệ với nhà sản xuất/lắp đặt ban đầu của bạn. Bạn phải xuất trình hóa đơn bán hàng
ban đầu hoặc xuất trình bằng chứng mua và lắp đặt STARON Solid Surfaces, chứng minh rõ ràng thể hiện đã mua sản
phẩm và ngày lắp đặt, để có được dịch vụ theo bảo hành này.
Để biết thêm thông tin chi tiết, xin liên hệ:
LOTTE Chemical Deutschland GMBH KölnerStr. 12 65760 Eschborn, Germany TEL+49 6196 77 272 75 LOTTE Chemical Thailand Co., Ltd. 16th Floor, Empire Tower, Unit 1602-1603, 1 South SathornRD, Yannawa, Bangkok, Thailand. 10120 Tel. +66-2-624-6737 LOTTE Chemical Deutschland GMBH-REPRESENTATIVE OFFICE (DUBAI) Office No 1702, Arenco Tower, Media City, Dubai, UAE. POBOX 48969 [email protected] Tel. +971-4-245-1401~1405
LOTTE Chemical Shanghai Co., Ltd. Rm2701, Shanghai International Trade Center, 2201 West Yan An Rd, Shanghai, China. 200336 Tel. +86-21-62703000-856 CÔNG TY TNHH SAMSUNG INTERIOR TP.HCM: 19W Nguyễn Hữu Cảnh, P.19, Quận Bình Thạnh HÀ NỘI: 166 Nguyễn Xiển, Quận Thanh Xuân HOTLINE: 028 3 7447 333 - 090 2580 097
Bảo hành này không sửa, đổi đổi bằng bất kỳ cách nào, ngoại trừ khi có văn bản thông báo chính thức có chữ ký của
một đại diện được ủy quyền của Lotte Chemical Corp.
CHÍNH SÁCH BẢO HÀNH 10 NĂM CỦA STARON