paramètre produits rendement quotidien en mois moyen 21 m³ … · 2020. 2. 27. · rendement...
TRANSCRIPT
-
ParamètreEmplacement: Congo (Dem. Rep.), Idiofa (5° Sud; 20°
Est)Température de l'eau:
25 °C
Rendement quot. requis:
20 m³; Dimensionnement pour mois moyen
Perte par saletés: 5,0 % Câble moteur: 90 m
Type de tuyau: - Hauteurmanométrique :
80 m Longueur du tuyau: -
Produits Quantité DétailsPS1800 HR-14H-2 -D 1 pce Système de pompe immergée comprenant contrôleur avec DataModule, moteur et extrémité de
pompeLC150-P36 14 pce 2.100 Wp; 7 x 2 modules; 15 ° incliné
Câble moteur 90 m 4 mm² Câble triphasé pour le courant et câble monophasé pour la mise à la terre
Accessoires 1ensemble
Well Probe, Float Switch, Surge Protector, PV Disconnect 440-40-6, PP2000 AC PowerPack
Rendement quotidien en mois moyen 21 m³
Val. quotid. Jan Fév Mar Avr Mai Jui Jui Aoû Sep Oct Nov Déc Moy.
Rendement[m³]
Energie [kWh] 7,9 8,6 9,0 9,1 9,5 10 10 9,5 9,3 8,3 7,8 7,6 8,9
Rayonnement [kWh/m²] 4,3 4,7 4,9 5,0 5,2 5,7 5,7 5,3 5,1 4,5 4,3 4,1 4,9
Pluviométrie [mm] 5,5 4,4 5,5 5,5 2,9 0,57 0,70 2,4 5,2 6,6 7,2 6,0 4,4
Temp. ambiante [°C] 25 25 25 25 26 28 28 29 27 25 25 25 26
Val. horaires 6:00 7:00 8:00 9:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00
Rendement[m³/h]
Energie [kWh] 0,007 0,27 0,57 0,85 1,1 1,2 1,2 1,1 1,0 0,83 0,55 0,26 0,006
Rayonnement [kWh/m²] 0,003 0,14 0,30 0,46 0,57 0,65 0,67 0,65 0,57 0,46 0,30 0,14 0,003
Temp. ambiante [°C] 21 21 22 24 26 28 30 31 31 31 31 30 30
Remarque: Bwalenge
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
1/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_80m
Projet de pompage solaire
-
ParamètreEmplacement: Congo (Dem. Rep.), Idiofa (5° Sud; 20°
Est)Température de l'eau:
25 °C
Rendement quot. requis:
20 m³; Dimensionnement pour mois moyen
Perte par saletés: 5,0 % Câble moteur: 170 m
Type de tuyau: - Hauteurmanométrique :
160 m Longueur du tuyau: -
Produits Quantité DétailsPS4000 HR-14HL-2 -D 1 pce Système de pompe immergée comprenant contrôleur avec DataModule, moteur et extrémité de
pompeLC100-M36 48 pce 4.800 Wp; 12 x 4 modules; 15 ° incliné
Câble moteur 170 m 4 mm² Câble triphasé pour le courant et câble monophasé pour la mise à la terre
Accessoires 1ensemble
Well Probe, Float Switch, SunSwitch, Surge Protector, PV Disconnect 440-40-6, PP4000 AC PowerPack
Rendement quotidien en mois moyen 19 m³
Val. quotid. Jan Fév Mar Avr Mai Jui Jui Aoû Sep Oct Nov Déc Moy.
Rendement[m³]
Energie [kWh] 18 20 21 21 22 24 23 22 21 19 18 18 20
Rayonnement [kWh/m²] 4,3 4,7 4,9 5,0 5,2 5,7 5,7 5,3 5,1 4,5 4,3 4,1 4,9
Pluviométrie [mm] 5,5 4,4 5,5 5,5 2,9 0,57 0,70 2,4 5,2 6,6 7,2 6,0 4,4
Temp. ambiante [°C] 25 25 25 25 26 28 28 29 27 25 25 25 26
Val. horaires 6:00 7:00 8:00 9:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00
Rendement[m³/h]
Energie [kWh] 0,015 0,61 1,3 2,0 2,4 2,7 2,7 2,6 2,4 1,9 1,3 0,59 0,014
Rayonnement [kWh/m²] 0,003 0,14 0,30 0,46 0,57 0,65 0,67 0,65 0,57 0,46 0,30 0,14 0,003
Temp. ambiante [°C] 21 21 22 24 26 28 30 31 31 31 31 30 30
Remarque: Nkutumayana
SunSwitch conditions requises de réglage min. 15 %
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
1/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_160m
Projet de pompage solaire
-
Caractéristique du système
Min. 800 W/m², 20 °C Max./STC*
Générateur PV Température des cellules [°C] 46 25
Perte de température [%] 8,4 -
Perte par saletés [%] 5,0 -
Pmax [Wp] 3.340 4.800
Vmp [V] 206 224
Imp [A] 16 21
Voc [V] 252 276
Isc [A] 18 23
Pout [W] 1.750 -
Vout [V] 241 -
Iout [A] 7,6 -
Câble moteur Perte de puissance [%] 5,0 5,0 14
Systèmes de pompe Puissance du moteur [W] 513 1.650 1.650
Tension du moteur [V EC] 69 218 218
Intensité du moteur [A] 7,4 7,6 7,6
Vitesse du moteur [rpm] 934 3.285 3.285
Débit [m³/h] 0,18 2,3 2,3
Efficacité [%] 13 58 58
*STC: Modules photovoltaïques en condition de test standard, rayonnement 1 000 W/m², température des cellules 25 °C
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
2/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_160m
Projet de pompage solaire
-
Schéma de branchement
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
3/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_160m
Projet de pompage solaire
-
System Layout
1: PS Controller
2: Submersible Pump
3: Stilling Tube
4: Well Probe
5: Cable Splice Kit
6: Grounding Rod
7: Surge Protector*
8: Safety Rope
9: Water Meter
10: Pressure Sensor
11: Float Switch
12: Sun Switch
13: PV Disconnect
14: Lightning Surge Protector
15: PV Generator
*Il est recommandé d'installer une protection contre les surtensions au niveau de chaque entrée de capteur du contrôleur.
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
4/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_160m
Projet de pompage solaire
-
Sizing Layout
H (Perte de pression statique):
Hauteur verticale du niveau dynamique de l’eau au point de livraison le plus élevé.
B (Abaissement de la nappe phréatique):
Abaissement de l’eau dépendant du débit et taux de récupération du puit.
D (Diamètre intérieur de la canalisation )L (Longueur du tuyau): Canalisation entière de la sortie de la pompe au point de livraison. Des coudes et armatures doivent être ajoutés
comme longueur de canalisation équivalente.M (Câble moteur): Câble entre le contrôleur et la pompe.
T (Angle d'inclinaison ): Angle entre le panneau du générateur PV et le panneau horizontal.
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
5/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_160m
Projet de pompage solaire
-
Chute max. 180 mDébit max. 2,6 m³/h
Contrôleur PS4000▪ Entrées de commande pour protection contre le fonctionnement à sec, commande à distance, etc.▪ Protection contre inversion de polarité, surcharge et surchauffe▪ MPPT (Maximum Power Point Tracking) intégré
Puissance max. 4,0 kWTension d'entrée max. 375 VOptimal Vmp** > 238 VIntensité du moteur max. 15 AEfficacité max. 98 %Temp. ambiante -30...50 °CClasse de protection IP65
Moteur ECDRIVE 4000-HR▪ Entretien minimal, moteur DC sans balais ▪ Rempli d'eau▪ Matériel de haute qualité, acier inoxydable: AISI 304/316▪ Moteur sans électronique à l'intérieur Puissance nominale 4,0 kWEfficacité max. 92 %Vitesse du moteur 900...3.300 rpmClasse d'isolation FClasse de protection IP68Submersion max. 150 m
Extrémité de la pompe PE HR-14HL***▪ Clapet anti-retour ▪ Matériel de haute qualité, acier inoxydable: AISI 304/316▪ En option : protection contre le fonctionnement à sec ▪ Helical rotor pump
Normes2006/42/EC, 2004/108/EC, 2006/95/EC
IEC/EN 61010-1:2010, IEC 62103:2003, IEC/EN 60034-1:2010,IEC/EN 60335-2-41:2003+A1+A2,IEC/EN 60335-1:2012, EN 62233:2008IEC/EN 61000-6-4:2007+A1, IEC/EN 61000-6-2:2005
IEC/EN 61702:1995, IEC/EN 62253 Ed.1
Les logos indiquent les autorisations obtenues pour cette gamme de produits. Les produits sont commandés et livrés selon les autorisations propres aux exigences du marché.
Pompe PU4000 HR-14HL (Moteur, Extrémité de la pompe)Diamètre de forage min. 4,0 inTempérature de l'eau max. 50 °C
Données techniques
Gamme de systèmes
* PS DataModule est inclus dans tous les contrôleurs PSk2 et n'importe quel contrôleur PS avec -D dans sa description. Les variantes -D devraient être commandées s'il y a un besoin potentiel d'utiliser les caractéristiques du PS DataModule à l'avenir, comme il n'y a pas d'option de montage ultérieur.
**Vmp: Tension MPP en condition de test standard (STC) : rayonnement solaire 1 000 W/m², température des cellules 25 °C ***Préciser la plage de température à la commande
PS DataModule - enregistreur de données intégré et caractéristiques de gestion de pompe avancées. Permet la configuration simple du système, données en temps réel et enregistrées et en plus fournit la communication Bluetooth au PumpScanner Android ™ App et PS Communicator.*
BERNT LORENTZ GmbH & Co. KGSiebenstuecken 24, 24558 Henstedt-Ulzburg, Germany, Tel +49 (0)4193 8806-700, www.lorentz.de
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.Les photos peuvent varier des produits réels selon les exigences et les réglementations du marché local.
Système de pompe solaire immergée pour puits 4" PS4000 HR-14HL
-
H =H2 =W1 =W2 =W3 =
D =D1 =
595 mm563 mm178 mm156 mm116 mm165 mm150 mm
Contrôleur
A =B =C =D =E =S =
913 mm245 mm668 mm96 mm147 mm1,25 in
Pompe **
Poids net
Contrôleur 9,0 kg
Pompe 16 kg
Moteur 10 kg
Extrémité de la pompe 5,5 kg
*Vmp: Tension MPP en condition de test standard (STC) : rayonnement solaire 1 000 W/m², température des cellules 25 °C **En taillant les rondelles en caoutchouc, le diamètre peut être réglé entre 6" et 4".
Dimensions et poids
Graphique de la pompe Vmp* > 238 V
BERNT LORENTZ GmbH & Co. KGSiebenstuecken 24, 24558 Henstedt-Ulzburg, Germany, Tel +49 (0)4193 8806-700, www.lorentz.de
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.Les photos peuvent varier des produits réels selon les exigences et les réglementations du marché local.
Système de pompe solaire immergée pour puits 4" PS4000 HR-14HL
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
Well Probe Mechanically Activated Device for Dry Run Protection in Applications with LORENTZ Solar Pump Systems
The switch can be used to detect the water level within a well. When the water level in the well dropped below the level of the well probe, the LORENTZ Controller will stop the pump and indicates Source Low LED.
ORDER INFORMATION
Item no.: 19-000000 product name: Well probe sensor
FEATURES
Reliable dry run protection Simple to install Trouble free operation Corrosion-free Splicing kit included
TECHNICAL DATA
Max. operating temperature 55 °C Enclosure class: IP68
Submersion depth: max 50 m Cable length: 1.5m Wire size: 2x 0.75mm² or AWG 19,
waterproofed Mounted in vertical position Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 260 x 170 x 40 mm 10.3 x 6.7 x 1.6 in
Total weight: 0.1 kg / 0.2 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
Float Switch Mechanically Activated Device for Water Level Detection in Applications with LORENTZ Solar Pump Systems
The switch can be used to detect the water level within a tank. When the water level in the tank reaches the maximum, the LORENTZ Controller will stop the pump and indicates Tank Full LED.
ORDER INFORMATION
Item no.: 19-000030 product name: Float Switch
FEATURES
N.O. (normally open) and N.C. (normally closed) function Reliable water level detection Simple to install Trouble free operation Not sensitive to rotation Corrosion-free
TECHNICAL DATA
Operating temperature: -10°C to 55°C Storage temperature: : -10°C to 55°C Enclosure class: IP68 Cable length: 3m, waterproof Wire size: 3x 1.0mm² or AWG 18 Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 230 x 160 x 55 mm 9.1 x 6.3 x 2.2 in
Total weight: 0.8 kg / 1.8 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
SunSwitch Automatic Solar Level Switching Device
The SunSwitch can be used for any application where you need to switch depending on the solar intensity. It is an autonomous working unit that supplies itself with power from the PV-module on its rear side.
ORDER INFORMATION
Item no.: 19-000050 product name: SUN SWITCH Light-Sensor
FEATURES
Trouble free operation Pump will only run when minimum flow rates or
pressure levels can be achieved which are required by certain applications
Reduced wear on the pump and motor since the pump only starts when it will continue to run
TECHNICAL DATA
Contact rating: Max. voltage 250 VAC / 220 VDC Max. current 2A Max. power 60 W / 62.5 VA
Enclosure class: IP54 Cable length: 4 m Wire size: 3x 1.0mm² or AWG 18, waterproofed Mounted close to the solar array Manual with further informations
is available in PartnerNet Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 230 x 115 x 90 mm 9.1 x 4.5 x 3.5 in
Total weight: 1.2 kg / 0.6 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
Surge Protector Device to Protect LORENTZ Pump Accessories from Voltage Spikes
ORDER INFORMATION
Item no.: 19-000280 product name: Surge Protector
FEATURES
Reliable surge protection for all LORENTZ pump accessories
Can be installed inside the PS Controller
TECHNICAL DATA
Max. voltage: 14 VDC Max current 8/20μs: 500 A Enclosure class: IP65 Ambient temperature: max. 50°C Wire size: 2x 1.5mm² or AWG 16 Meets the requirements for CE
DIMENSION/WEIGHT
Packing dimensions: 70 x 45 x 20 mm 2.8 x 1.8 x 0.8 in
Total weight 0.1 kg / 0.2 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations
V15
0528
PV Disconnect 440-40-6 Connection box with DC Disconnect Switch and optional lightning surge protection
ORDER INFORMATION Item no.: 19-000136 product name: PV Disconnect 440-40-6 Item no.: 19-002120 product name: MNSPD-115 Item no.: 19-002130 product name: MNSPD-300 Item no.: 19-002140 product name: MNSPD-600
Lightning surge protectors must be ordered separately
FEATURES
Designed for PS150 – PS4000 For professional installation of pumping
systems
TECHNICAL DATA
Wiring up to 6 PV-strings in parallel DC rated disconnect switch enclosed Enclosure class IP 54 Meets the requirements for CE
PV Disconnect 440-40-6 Max. voltage 440 V DC
Max. current per string 10 A
Max. total current 40 A
Max. no. of strings 6
String cable size 2,5 - 4mm²
Output cable size 4 - 10mm²
Optional lightning surge protector
Connects through an existing mounting hole in the PV connect housing
Proper grounding of the device is manda-tory to achieve protection
Controller MidNite surge protector PS150 – PS200 MNSPD115
PS600 – PS1800 MNSPD300
PS4000 MNSPD600
DIMENSION/WEIGHT [mm]
Optional lightning protection
Net. Weight: 2,15kg (+0,35kg)
Optional lightning protection
PG cable glands (2x PG11 13x M16)
Optprot
Mounting hole (1x PG16 cap)
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
PP4000 AC PowerPack AC/DC Converter to Supply PS4000 Pump Systems with Backup Power from a Generator or Mains Supply
ORDER INFORMATION
Item no.: 19-000180 product name: Power Pack 4000
TECHNICAL DATA
3-Phase AC input: 380V (±20 %), 45 to 65Hz DC output: 190-286V, 5.7kW DC output rated current: 20A @ 230V DC Must be protected from direct mid-day sun IP42 Ambient temperature: –5 to 45°C Efficiency up to 94% Passive cooling, no fan All wires must be #14 AWG (2.5 mm²) or larger Manual with further informations
is available in PartnerNet Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 332 x 210 x 202 mm 15.7 x 8.7 x 8.3 in
Total weight: 14.5 kg / 30 lbs
-
BERNT LORENTZ GmbH & Co. KGSiebenstuecken 24, 24558 Henstedt-Ulzburg, Germany, Tel. +49 (0) 4193 8806 - 700
Errors excepted and possible alterations without prior notice. Pictures may differ from actual products depending on local market requirements and regulations. A pump system consists of a controller, motor and pump end. Multiple pumps/pump ends are shown to represent the wide range of pumps (over 70) that LORENTZ has.
To fi nd out more visit www.lorentz.de
151118
LC100-M36 High-efficiency PV Module
Features
high energy yields ensured by high conversion efficiency
sturdy, clear-anodized aluminum frame with pre-drilled holes for quick installation
advanced EVA encapsulation with triple-layer backsheet, meets the most stringent safety requirements for high-voltage operation
pre-wired junction box equipped with connec-tors ”plug‘n‘play“
reliable bypass diodes to prevent overheating (hot spot effect) and to minimise power loss by shading
manufactured in ISO 9001:2000-certified factory
Specifications
Electrical Data
Peak power Pmax [Wp] 100
Tolerance [%] + 5/0
Max. power current Imp [A] 5.35
Max. power voltage Vmp [V] 18.7
Short circuit current Isc [A] 5.72
Open circuit voltage Voc [V] 23.0
Temperature co-efficient for Pmax [%/°C] -0.4
Temperature co-efficient for Voc [%/°C] -0.33
Temperature co-efficient for Isc [%/°C] 0.05
Max. system voltage [VDC] 1,000
Module efficiency [%] 15.13
Practical module efficiency [%] 17.94
All technical data at standard test condition: AM = 1.5, E = 1,000 W/m², cell temperature: 25 °C
Cells
Number of cells in series 36
Number of cells in parallel 1
Cell technology monocrystalline
Cell shape rectangular
Warranty
Warranty: 2 years
Performance guarantee: up to 10 years (90% power output) up to 20 years (80% power output)
Details according to warranty issued by LORENTZ
phot
o m
ay d
iffer
from
act
ual p
rodu
ct
Standards
LC100-M36 is certified according to IEC 61215 and 61730 by TÜV Rheinland and meets the requirements for CE.
• Qualified, IEC 61215• Safety tested, IEC 61730• Periodic Inspection
phot
o m
ay d
iffer
from
act
ual p
rodu
ct
-
BERNT LORENTZ GmbH & Co. KGSiebenstuecken 24, 24558 Henstedt-Ulzburg, Germany, Tel. +49 (0) 4193 8806 - 700
Errors excepted and possible alterations without prior notice. Pictures may differ from actual products depending on local market requirements and regulations. A pump system consists of a controller, motor and pump end. Multiple pumps/pump ends are shown to represent the wide range of pumps (over 70) that LORENTZ has.
To fi nd out more visit www.lorentz.de
151118
Electrical Performance
Physical Specifications mm
Cell temperature [°C] Irradiance [W/m2]
0 10 20 30 -25 0 +25 +50 +75 100 0 200 400 600 800 1000 1,200 0 10 20 30
Curre
nt [A
]
Curre
nt [A
]
Nor
mal
ised
Isc, V
oc a
nd P
max
(%)
Nor
mal
ised
Isc, V
oc a
nd P
max
(%)
75°C
Isc
Isc
VocVoc
Pmax
Pmax
25°C
50°C
4 4
5 5
3 3
6 6
2 2
1 1
80 80
100 100
120 120
140 140
60 60
40 40
20 20
0 00 0
Weight [kg] 8.1
Dimension [mm] 1,197 × 552 × 35
Strength [N/m2] 2,400
Cable approx. 900 mm, 4 mm2
Connectors MC4 PV-KBT4/6II-UR / PV-KST4/6II-UR
Electrical Performance
for different temperatures, at AM=1.5, E=1,000 W/m2
Electrical Performance
for different irradiation, at 25 °C
Temperature Dependence
of Isc, Voc and Pmax
Irradiation Dependence
of Isc, Voc and Pmax at 25 °C
Voltage [V]
1,000 W/m2
800 W/m2
600 W/m2
400 W/m2
200 W/m2
Voltage [V]
1,19
7 [4
7.1]
417
[16.
4]
917[
36.1
]
35 [1.4]
Ø 4
9 ×14
9 ×14
35 [1.4]
10 [0.4]
35 [1
.4]
552 [21.7] 502 [19.8]
A‘ A‘A‘A AA
A‘A
A‘
A
-
ParamètreEmplacement: Congo (Dem. Rep.), Idiofa (5° Sud; 20°
Est)Température de l'eau:
25 °C
Rendement quot. requis:
20 m³; Dimensionnement pour mois moyen
Perte par saletés: 5,0 % Câble moteur: 210 m
Type de tuyau: - Hauteurmanométrique :
200 m Longueur du tuyau: -
Produits Quantité DétailsPS4000 C-SJ3-32 -D 1 pce Système de pompe immergée comprenant contrôleur avec DataModule, moteur et extrémité de
pompeLC150-P36 48 pce 7.200 Wp; 12 x 4 modules; 15 ° incliné
Câble moteur 210 m 13 mm² Câble triphasé pour le courant et câble monophasé pour la mise à la terre
Accessoires 1ensemble
Well Probe, Float Switch, SunSwitch, Surge Protector, PV Disconnect 440-40-6, PP4000 AC PowerPack
Rendement quotidien en mois moyen 19 m³
Val. quotid. Jan Fév Mar Avr Mai Jui Jui Aoû Sep Oct Nov Déc Moy.
Rendement[m³]
Energie [kWh] 27 29 31 31 32 35 35 33 32 29 27 26 31
Rayonnement [kWh/m²] 4,3 4,7 4,9 5,0 5,2 5,7 5,7 5,3 5,1 4,5 4,3 4,1 4,9
Pluviométrie [mm] 5,5 4,4 5,5 5,5 2,9 0,57 0,70 2,4 5,2 6,6 7,2 6,0 4,4
Temp. ambiante [°C] 25 25 25 25 26 28 28 29 27 25 25 25 26
Val. horaires 6:00 7:00 8:00 9:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00
Rendement[m³/h]
Energie [kWh] 0,022 0,92 2,0 2,9 3,6 4,0 4,1 3,9 3,5 2,8 1,9 0,89 0,021
Rayonnement [kWh/m²] 0,003 0,14 0,30 0,46 0,57 0,65 0,67 0,65 0,57 0,46 0,30 0,14 0,003
Temp. ambiante [°C] 21 21 22 24 26 28 30 31 31 31 31 30 30
Remarque: Kipuku1Kipuku2
SunSwitch conditions requises de réglage min. 20 %
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
1/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_200m
Projet de pompage solaire
-
�aractéristique du système
Min. 800 � /m�� 20 �� Ma�./S���
�énérateur PV Température des cellules [°C] 46 25
Perte de température [%] 8,8 -
Perte par saletés [%] 5,0 -
Pmax [Wp] 4.990 7.200
Vmp [V] 206 226
Imp [A] 24 32
Voc [V] 248 272
Isc [A] 26 34
Pout [W] 3.310 -
Vout [V] 236 -
Iout [A] 14 -
���le moteur Perte de puissance [%] 1,8 3,7 3,7
Systèmes de pompe Puissance du moteur [W] 997 3.165 3.165
Tension du moteur [V EC] 179 219 219
Intensité du moteur [A] 5,6 14 14
Vitesse du moteur [rpm] 2.920 3.245 3.245
Débit [m³/h] 0 2,6 2,6
Efficacité [%] 0 44 44
*STC: Modules photovoltaïques en condition de test standard, rayonnement 1 000 W/m², température des cellules 25 °C
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
2/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_200m
Projet de pompage solaire
-
Schéma de �ranchement
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
3/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_200m
Projet de pompage solaire
-
System �ayout
1: PS Controller
2: Submersible Pump
3: Stilling Tube
4: Well Probe
5: Cable Splice Kit
6: Grounding Rod
7: Surge Protector*
8: Safety Rope
9: Water Meter
10: Pressure Sensor
11: Float Switch
12: Sun Switch
13: PV Disconnect
14: Lightning Surge Protector
15: PV Generator
*Il est recommandé d'installer une protection contre les surtensions au niveau de chaque entrée de capteur du contrôleur.
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
4/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_200m
Projet de pompage solaire
-
Si�ing �ayout
� �Perte de pression statique�:
Hauteur verticale du niveau dynamique de l’eau au point de livraison le plus élevé.
� �A�aissement de la nappe phréatique�:
Abaissement de l’eau dépendant du débit et taux de récupération du puit.
D �Diamètre intérieur de la canalisation �� ��ongueur du tuyau�: Canalisation entière de la sortie de la pompe au point de livraison. Des coudes et armatures doivent être ajoutés
comme longueur de canalisation équivalente.M ����le moteur�: Câble entre le contrôleur et la pompe.
� �Angle d�inclinaison �: Angle entre le panneau du générateur PV et le panneau horizontal.
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
5/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_200m
Projet de pompage solaire
-
Chute max. 220 mDébit max. 4,4 m³/h
�ontr�leur PS4000▪ Entrées de commande pour protection contre le fonctionnement à sec, commande à distance, etc.▪ Protection contre inversion de polarité, surcharge et surchauffe▪ MPPT (Maximum Power Point Tracking) intégré
Puissance max. 4,0 kWTension d'entrée max. 375 VOptimal Vmp** > 238 VIntensité du moteur max. 15 AEfficacité max. 98 %Temp. ambiante -30...50 °CClasse de protection IP65
Moteur ��DR�V� 4000��▪ Entretien minimal, moteur DC sans balais ▪ Rempli d'eau▪ Matériel de haute qualité, acier inoxydable: AISI 304/316▪ Moteur sans électronique à l'intérieur Puissance nominale 4,0 kWEfficacité max. 92 %Vitesse du moteur 900...3.300 rpmClasse d'isolation FClasse de protection IP68Submersion max. 150 m
��trémité de la pompe P� ��SJ3�32▪ Clapet anti-retour ▪ Matériel de haute qualité, acier inoxydable: AISI 304▪ En option : protection contre le fonctionnement à sec ▪ Centrifugal pump
Normes2006/42/EC, 2004/108/EC, 2006/95/EC
IEC/EN 61010-1:2010, IEC 62103:2003, IEC/EN 60034-1:2010,IEC/EN 60335-2-41:2003+A1+A2,IEC/EN 60335-1:2012, EN 62233:2008IEC/EN 61000-6-4:2007+A1, IEC/EN 61000-6-2:2005
IEC/EN 61702:1995, IEC/EN 62253 Ed.1
Les logos indiquent les autorisations obtenues pour cette gamme de produits. Les produits sont commandés et livrés selon les autorisations propres aux exigences du marché.
Pompe P�4000 ��SJ3�32 �Moteur� ��trémité de la pompe�Diamètre de forage min. 4,0 inTempérature de l'eau max. 50 °C
Données techniques
�amme de systèmes
* PS DataModule est inclus dans tous les contrôleurs PSk2 et n'importe quel contrôleur PS avec -D dans sa description. Les variantes -D devraient être commandées s'il y a un besoin potentiel d'utiliser les caractéristiques du PS DataModule à l'avenir, comme il n'y a pas d'option de montage ultérieur.
**Vmp: Tension MPP en condition de test standard (STC) : rayonnement solaire 1 000 W/m², température des cellules 25 °C
PS DataModule - enregistreur de données intégré et caractéristiques de gestion de pompe avancées. Permet la configuration simple du système, données en temps réel et enregistrées et en plus fournit la communication Bluetooth au PumpScanner Android ™ App et PS Communicator.*
��RN� �OR�N�� �m�� � �o. ��Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany, Tel +49 (0)4193 8806-700, www.lorentz.de
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.Les photos peuvent varier des produits réels selon les exigences et les réglementations du marché local.
Système de pompe solaire immergée pour puits 4� PS4000 ��SJ3�32
-
H =H2 =W1 =W2 =W3 =
D =D1 =
595 mm563 mm178 mm156 mm116 mm165 mm150 mm
�ontr�leur
A =B =C =D =E =S =
1.088 mm245 mm843 mm96 mm98 mm1,25 in
Pompe
Poids net
Contrôleur 9,0 kg
Pompe 20 kg
Moteur 10 kg
Extrémité de la pompe 9,5 kg
*Vmp: Tension MPP en condition de test standard (STC) : rayonnement solaire 1 000 W/m², température des cellules 25 °C
Dimensions et poids
�raphique de la pompe Vmp* > 238 V
��RN� �OR�N�� �m�� � �o. ��Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany, Tel +49 (0)4193 8806-700, www.lorentz.de
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.Les photos peuvent varier des produits réels selon les exigences et les réglementations du marché local.
Système de pompe solaire immergée pour puits 4� PS4000 ��SJ3�32
-
��RN� �OR�N�� �m�� � �o. �� Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
Well Probe Mechanically Activated Device for Dry Run Protection in Applications with LORENTZ Solar Pump Systems
The switch can be used to detect the water level within a well. When the water level in the well dropped below the level of the well probe, the LORENTZ Controller will stop the pump and indicates Source Low LED.
ORDER INFORMATION
Item no.: 19-000000 product name: Well probe sensor
FEATURES
Reliable dry run protection Simple to install Trouble free operation Corrosion-free Splicing kit included
TECHNICAL DATA
Max. operating temperature 55 °C Enclosure class: IP68
Submersion depth: max 50 m Cable length: 1.5m Wire size: 2x 0.75mm² or AWG 19,
waterproofed Mounted in vertical position Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 260 x 170 x 40 mm 10.3 x 6.7 x 1.6 in
Total weight: 0.1 kg / 0.2 lbs
-
��RN� �OR�N�� �m�� � �o. �� Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
Float Switch Mechanically Activated Device for Water Level Detection in Applications with LORENTZ Solar Pump Systems
The switch can be used to detect the water level within a tank. When the water level in the tank reaches the maximum, the LORENTZ Controller will stop the pump and indicates Tank Full LED.
ORDER INFORMATION
Item no.: 19-000030 product name: Float Switch
FEATURES
N.O. (normally open) and N.C. (normally closed) function Reliable water level detection Simple to install Trouble free operation Not sensitive to rotation Corrosion-free
TECHNICAL DATA
Operating temperature: -10°C to 55°C Storage temperature: : -10°C to 55°C Enclosure class: IP68 Cable length: 3m, waterproof Wire size: 3x 1.0mm² or AWG 18 Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 230 x 160 x 55 mm 9.1 x 6.3 x 2.2 in
Total weight: 0.8 kg / 1.8 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
SunSwitch Automatic Solar Level Switching Device
The SunSwitch can be used for any application where you need to switch depending on the solar intensity. It is an autonomous working unit that supplies itself with power from the PV-module on its rear side.
ORDER INFORMATION
Item no.: 19-000050 product name: SUN SWITCH Light-Sensor
FEATURES
Trouble free operation Pump will only run when minimum flow rates or
pressure levels can be achieved which are required by certain applications
Reduced wear on the pump and motor since the pump only starts when it will continue to run
TECHNICAL DATA
Contact rating: Max. voltage 250 VAC / 220 VDC Max. current 2A Max. power 60 W / 62.5 VA
Enclosure class: IP54 Cable length: 4 m Wire size: 3x 1.0mm² or AWG 18, waterproofed Mounted close to the solar array Manual with further informations
is available in PartnerNet Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 230 x 115 x 90 mm 9.1 x 4.5 x 3.5 in
Total weight: 1.2 kg / 0.6 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
Surge Protector Device to Protect LORENTZ Pump Accessories from Voltage Spikes
ORDER INFORMATION
Item no.: 19-000280 product name: Surge Protector
FEATURES
Reliable surge protection for all LORENTZ pump accessories
Can be installed inside the PS Controller
TECHNICAL DATA
Max. voltage: 14 VDC Max current 8/20μs: 500 A Enclosure class: IP65 Ambient temperature: max. 50°C Wire size: 2x 1.5mm² or AWG 16 Meets the requirements for CE
DIMENSION/WEIGHT
Packing dimensions: 70 x 45 x 20 mm 2.8 x 1.8 x 0.8 in
Total weight 0.1 kg / 0.2 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations
V15
0528
PV Disconnect 440-40-6 Connection box with DC Disconnect Switch and optional lightning surge protection
ORDER INFORMATION Item no.: 19-000136 product name: PV Disconnect 440-40-6 Item no.: 19-002120 product name: MNSPD-115 Item no.: 19-002130 product name: MNSPD-300 Item no.: 19-002140 product name: MNSPD-600
Lightning surge protectors must be ordered separately
FEATURES
Designed for PS150 – PS4000 For professional installation of pumping
systems
TECHNICAL DATA
Wiring up to 6 PV-strings in parallel DC rated disconnect switch enclosed Enclosure class IP 54 Meets the requirements for CE
PV Disconnect 440-40-6 Max. voltage 440 V DC
Max. current per string 10 A
Max. total current 40 A
Max. no. of strings 6
String cable size 2,5 - 4mm²
Output cable size 4 - 10mm²
Optional lightning surge protector
Connects through an existing mounting hole in the PV connect housing
Proper grounding of the device is manda-tory to achieve protection
Controller MidNite surge protector PS150 – PS200 MNSPD115
PS600 – PS1800 MNSPD300
PS4000 MNSPD600
DIMENSION/WEIGHT [mm]
Optional lightning protection
Net. Weight: 2,15kg (+0,35kg)
Optional lightning protection
PG cable glands (2x PG11 13x M16)
Optprot
Mounting hole (1x PG16 cap)
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
PP4000 AC PowerPack AC/DC Converter to Supply PS4000 Pump Systems with Backup Power from a Generator or Mains Supply
ORDER INFORMATION
Item no.: 19-000180 product name: Power Pack 4000
TECHNICAL DATA
3-Phase AC input: 380V (±20 %), 45 to 65Hz DC output: 190-286V, 5.7kW DC output rated current: 20A @ 230V DC Must be protected from direct mid-day sun IP42 Ambient temperature: –5 to 45°C Efficiency up to 94% Passive cooling, no fan All wires must be #14 AWG (2.5 mm²) or larger Manual with further informations
is available in PartnerNet Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 332 x 210 x 202 mm 15.7 x 8.7 x 8.3 in
Total weight: 14.5 kg / 30 lbs
-
BERNT LORENTZ GmbH & Co. KGSiebenstuecken 24, 24558 Henstedt-Ulzburg, Germany, Tel. +49 (0) 4193 8806 - 700
Errors excepted and possible alterations without prior notice. Pictures may differ from actual products depending on local market requirements and regulations. A pump system consists of a controller, motor and pump end. Multiple pumps/pump ends are shown to represent the wide range of pumps (over 70) that LORENTZ has.
To fi nd out more visit www.lorentz.de
151118
LC150-P36 High-efficiency PV Module
Features
high energy yields ensured by high conversion efficiency
sturdy, clear-anodized aluminum frame with pre-drilled holes for quick installation
advanced EVA encapsulation with triple-layer backsheet, meets the most stringent safety requirements for high-voltage operation
pre-wired junction box equipped with connec-tors ”plug‘n‘play“
reliable bypass diodes to prevent overheating (hot spot effect) and to minimise power loss by shading
manufactured in ISO 9001:2000-certified factory
Specifications
Electrical Data
Peak power Pmax [Wp] 150
Tolerance [%] + 5/0
Max. power current Imp [A] 7.98
Max. power voltage Vmp [V] 18.8
Short circuit current Isc [A] 8.5
Open circuit voltage Voc [V] 22.7
Temperature co-efficient for Pmax [%/°C] -0.42
Temperature co-efficient for Voc [%/°C] -0.34
Temperature co-efficient for Isc [%/°C] 0.06
Max. system voltage [VDC] 1,000
Module efficiency [%] 14.94
Practical module efficiency [%] 17.12
All technical data at standard test condition: AM = 1.5, E = 1,000 W/m², cell temperature: 25 °C
Cells
Number of cells in series 36
Number of cells in parallel 1
Cell technology polycrystalline
Cell shape rectangular
Warranty
Warranty: 2 years
Performance guarantee: up to 10 years (90% power output) up to 20 years (80% power output)
Details according to warranty issued by LORENTZ
phot
o m
ay d
iffer
from
act
ual p
rodu
ct
Standards
LC150-P36 is certified according to IEC 61215 and 61730 by TÜV Rheinland and meets the requirements for CE.
• Qualified, IEC 61215• Safety tested, IEC 61730• Periodic Inspection
-
BERNT LORENTZ GmbH & Co. KGSiebenstuecken 24, 24558 Henstedt-Ulzburg, Germany, Tel. +49 (0) 4193 8806 - 700
Errors excepted and possible alterations without prior notice. Pictures may differ from actual products depending on local market requirements and regulations. A pump system consists of a controller, motor and pump end. Multiple pumps/pump ends are shown to represent the wide range of pumps (over 70) that LORENTZ has.
To fi nd out more visit www.lorentz.de
151118
Electrical Performance
Physical Specifications mm
Cell temperature [°C] Irradiance [W/m2]
0 10 20 30 -25 0 +25 +50 +75 100 0 200 400 600 800 1000 1,200 0 10 20 30
Curre
nt [A
]
Curre
nt [A
]
Nor
mal
ised
Isc, V
oc a
nd P
max
(%)
Nor
mal
ised
Isc, V
oc a
nd P
max
(%)
75°C
Isc
Isc
VocVoc
Pmax
Pmax
25°C
50°C4 4
7 7
5 5
8 8
3 3
6 6
9 9
2 2
1 1
80 80
100 100
120 120
140 140
60 60
40 40
20 20
0 00 0
Weight [kg] 12.0
Dimension [mm] 1,492 × 673 × 40
Strength [N/m2] 2,400
Cable approx. 900 mm, 4 mm2
Connectors MC4 PV-KBT4/6II-UR / PV-KST4/6II-UR
Electrical Performance
for different temperatures, at AM=1.5, E=1,000 W/m2
Electrical Performance
for different irradiation, at 25 °C
Temperature Dependence
of Isc, Voc and Pmax
Irradiation Dependence
of Isc, Voc and Pmax at 25 °C
Voltage [V]
1,000 W/m2
800 W/m2
600 W/m2
400 W/m2
200 W/m2
Voltage [V]
1,49
2 [5
8.7]
712
[28]
1,21
2 [4
7.7]
40 [1.6]
Ø 4
9 ×14
9 ×14
35 [1.4]
10 [0.4]
40 [1
.6]
673 [26.5] 623 [24.5]
A‘A A‘AA‘A
A‘A
A‘
A
-
ParamètreEmplacement: Congo (Dem. Rep.), Idiofa (5° Sud; 20°
Est)Température de l'eau:
25 °C
Rendement quot. requis:
20 m³; Dimensionnement pour mois moyen
Perte par saletés: 5,0 % Câble moteur: 140 m
Type de tuyau: - Hauteurmanométrique :
130 m Longueur du tuyau: -
Produits Quantité DétailsPS4000 HR-14HL-2 -D 1 pce Système de pompe immergée comprenant contrôleur avec DataModule, moteur et extrémité de
pompeLC150-P36 24 pce 3.600 Wp; 12 x 2 modules; 15 ° incliné
Câble moteur 140 m 4 mm² Câble triphasé pour le courant et câble monophasé pour la mise à la terre
Accessoires 1ensemble
Well Probe, Float Switch, SunSwitch, Surge Protector, PV Disconnect 440-40-6, PP4000 AC PowerPack
Rendement quotidien en mois moyen 20 m³
Val. quotid. Jan Fév Mar Avr Mai Jui Jui Aoû Sep Oct Nov Déc Moy.
Rendement[m³]
Energie [kWh] 14 15 15 16 16 18 18 16 16 14 13 13 15
Rayonnement [kWh/m²] 4,3 4,7 4,9 5,0 5,2 5,7 5,7 5,3 5,1 4,5 4,3 4,1 4,9
Pluviométrie [mm] 5,5 4,4 5,5 5,5 2,9 0,57 0,70 2,4 5,2 6,6 7,2 6,0 4,4
Temp. ambiante [°C] 25 25 25 25 26 28 28 29 27 25 25 25 26
Val. horaires 6:00 7:00 8:00 9:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00
Rendement[m³/h]
Energie [kWh] 0,011 0,46 0,98 1,5 1,8 2,0 2,0 2,0 1,8 1,4 0,95 0,44 0,011
Rayonnement [kWh/m²] 0,003 0,14 0,30 0,46 0,57 0,65 0,67 0,65 0,57 0,46 0,30 0,14 0,003
Temp. ambiante [°C] 21 21 22 24 26 28 30 31 31 31 31 30 30
Remarque: Kalanganda
SunSwitch conditions requises de réglage min. 15 %
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
1/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_130m
Projet de pompage solaire
-
�aractéristique du système
Min. 800 � /m�� 20 �� Ma�./S���
�énérateur PV Température des cellules [°C] 46 25
Perte de température [%] 8,8 -
Perte par saletés [%] 5,0 -
Pmax [Wp] 2.495 3.600
Vmp [V] 206 226
Imp [A] 12 16
Voc [V] 248 272
Isc [A] 13 17
Pout [W] 1.435 -
Vout [V] 238 -
Iout [A] 6,1 -
���le moteur Perte de puissance [%] 3,7 3,7 11
Systèmes de pompe Puissance du moteur [W] 390 1.370 1.370
Tension du moteur [V EC] 64 212 212
Intensité du moteur [A] 6,1 6,5 6,5
Vitesse du moteur [rpm] 930 3.285 3.285
Débit [m³/h] 0,30 2,4 2,4
Efficacité [%] 24 60 60
*STC: Modules photovoltaïques en condition de test standard, rayonnement 1 000 W/m², température des cellules 25 °C
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
2/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_130m
Projet de pompage solaire
-
Schéma de �ranchement
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
3/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_130m
Projet de pompage solaire
-
System �ayout
1: PS Controller
2: Submersible Pump
3: Stilling Tube
4: Well Probe
5: Cable Splice Kit
6: Grounding Rod
7: Surge Protector*
8: Safety Rope
9: Water Meter
10: Pressure Sensor
11: Float Switch
12: Sun Switch
13: PV Disconnect
14: Lightning Surge Protector
15: PV Generator
*Il est recommandé d'installer une protection contre les surtensions au niveau de chaque entrée de capteur du contrôleur.
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
4/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_130m
Projet de pompage solaire
-
Si�ing �ayout
� �Perte de pression statique�:
Hauteur verticale du niveau dynamique de l’eau au point de livraison le plus élevé.
� �A�aissement de la nappe phréatique�:
Abaissement de l’eau dépendant du débit et taux de récupération du puit.
D �Diamètre intérieur de la canalisation �� ��ongueur du tuyau�: Canalisation entière de la sortie de la pompe au point de livraison. Des coudes et armatures doivent être ajoutés
comme longueur de canalisation équivalente.M ����le moteur�: Câble entre le contrôleur et la pompe.
� �Angle d�inclinaison �: Angle entre le panneau du générateur PV et le panneau horizontal.
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
5/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_130m
Projet de pompage solaire
-
��RN� �OR�N�� �m�� � �o. �� Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
Well Probe Mechanically Activated Device for Dry Run Protection in Applications with LORENTZ Solar Pump Systems
The switch can be used to detect the water level within a well. When the water level in the well dropped below the level of the well probe, the LORENTZ Controller will stop the pump and indicates Source Low LED.
ORDER INFORMATION
Item no.: 19-000000 product name: Well probe sensor
FEATURES
Reliable dry run protection Simple to install Trouble free operation Corrosion-free Splicing kit included
TECHNICAL DATA
Max. operating temperature 55 °C Enclosure class: IP68
Submersion depth: max 50 m Cable length: 1.5m Wire size: 2x 0.75mm² or AWG 19,
waterproofed Mounted in vertical position Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 260 x 170 x 40 mm 10.3 x 6.7 x 1.6 in
Total weight: 0.1 kg / 0.2 lbs
-
��RN� �OR�N�� �m�� � �o. �� Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
Float Switch Mechanically Activated Device for Water Level Detection in Applications with LORENTZ Solar Pump Systems
The switch can be used to detect the water level within a tank. When the water level in the tank reaches the maximum, the LORENTZ Controller will stop the pump and indicates Tank Full LED.
ORDER INFORMATION
Item no.: 19-000030 product name: Float Switch
FEATURES
N.O. (normally open) and N.C. (normally closed) function Reliable water level detection Simple to install Trouble free operation Not sensitive to rotation Corrosion-free
TECHNICAL DATA
Operating temperature: -10°C to 55°C Storage temperature: : -10°C to 55°C Enclosure class: IP68 Cable length: 3m, waterproof Wire size: 3x 1.0mm² or AWG 18 Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 230 x 160 x 55 mm 9.1 x 6.3 x 2.2 in
Total weight: 0.8 kg / 1.8 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
SunSwitch Automatic Solar Level Switching Device
The SunSwitch can be used for any application where you need to switch depending on the solar intensity. It is an autonomous working unit that supplies itself with power from the PV-module on its rear side.
ORDER INFORMATION
Item no.: 19-000050 product name: SUN SWITCH Light-Sensor
FEATURES
Trouble free operation Pump will only run when minimum flow rates or
pressure levels can be achieved which are required by certain applications
Reduced wear on the pump and motor since the pump only starts when it will continue to run
TECHNICAL DATA
Contact rating: Max. voltage 250 VAC / 220 VDC Max. current 2A Max. power 60 W / 62.5 VA
Enclosure class: IP54 Cable length: 4 m Wire size: 3x 1.0mm² or AWG 18, waterproofed Mounted close to the solar array Manual with further informations
is available in PartnerNet Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 230 x 115 x 90 mm 9.1 x 4.5 x 3.5 in
Total weight: 1.2 kg / 0.6 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
Surge Protector Device to Protect LORENTZ Pump Accessories from Voltage Spikes
ORDER INFORMATION
Item no.: 19-000280 product name: Surge Protector
FEATURES
Reliable surge protection for all LORENTZ pump accessories
Can be installed inside the PS Controller
TECHNICAL DATA
Max. voltage: 14 VDC Max current 8/20μs: 500 A Enclosure class: IP65 Ambient temperature: max. 50°C Wire size: 2x 1.5mm² or AWG 16 Meets the requirements for CE
DIMENSION/WEIGHT
Packing dimensions: 70 x 45 x 20 mm 2.8 x 1.8 x 0.8 in
Total weight 0.1 kg / 0.2 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations
V15
0528
PV Disconnect 440-40-6 Connection box with DC Disconnect Switch and optional lightning surge protection
ORDER INFORMATION Item no.: 19-000136 product name: PV Disconnect 440-40-6 Item no.: 19-002120 product name: MNSPD-115 Item no.: 19-002130 product name: MNSPD-300 Item no.: 19-002140 product name: MNSPD-600
Lightning surge protectors must be ordered separately
FEATURES
Designed for PS150 – PS4000 For professional installation of pumping
systems
TECHNICAL DATA
Wiring up to 6 PV-strings in parallel DC rated disconnect switch enclosed Enclosure class IP 54 Meets the requirements for CE
PV Disconnect 440-40-6 Max. voltage 440 V DC
Max. current per string 10 A
Max. total current 40 A
Max. no. of strings 6
String cable size 2,5 - 4mm²
Output cable size 4 - 10mm²
Optional lightning surge protector
Connects through an existing mounting hole in the PV connect housing
Proper grounding of the device is manda-tory to achieve protection
Controller MidNite surge protector PS150 – PS200 MNSPD115
PS600 – PS1800 MNSPD300
PS4000 MNSPD600
DIMENSION/WEIGHT [mm]
Optional lightning protection
Net. Weight: 2,15kg (+0,35kg)
Optional lightning protection
PG cable glands (2x PG11 13x M16)
Optprot
Mounting hole (1x PG16 cap)
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
PP4000 AC PowerPack AC/DC Converter to Supply PS4000 Pump Systems with Backup Power from a Generator or Mains Supply
ORDER INFORMATION
Item no.: 19-000180 product name: Power Pack 4000
TECHNICAL DATA
3-Phase AC input: 380V (±20 %), 45 to 65Hz DC output: 190-286V, 5.7kW DC output rated current: 20A @ 230V DC Must be protected from direct mid-day sun IP42 Ambient temperature: –5 to 45°C Efficiency up to 94% Passive cooling, no fan All wires must be #14 AWG (2.5 mm²) or larger Manual with further informations
is available in PartnerNet Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 332 x 210 x 202 mm 15.7 x 8.7 x 8.3 in
Total weight: 14.5 kg / 30 lbs
-
ParamètreEmplacement: Congo (Dem. Rep.), Idiofa (5° Sud; 20°
Est)Température de l'eau:
25 °C
Rendement quot. requis:
20 m³; Dimensionnement pour mois moyen
Perte par saletés: 5,0 % Câble moteur: 130 m
Type de tuyau: - Hauteurmanométrique :
120 m Longueur du tuyau: -
Produits Quantité DétailsPS4000 HR-14HL-2 -D 1 pce Système de pompe immergée comprenant contrôleur avec DataModule, moteur et extrémité de
pompeLC150-P36 22 pce 3.300 Wp; 11 x 2 modules; 15 ° incliné
Câble moteur 130 m 4 mm² Câble triphasé pour le courant et câble monophasé pour la mise à la terre
Accessoires 1ensemble
Well Probe, Float Switch, SunSwitch, Surge Protector, PV Disconnect 440-40-6, PP4000 AC PowerPack
Rendement quotidien en mois moyen 20 m³
Val. quotid. Jan Fév Mar Avr Mai Jui Jui Aoû Sep Oct Nov Déc Moy.
Rendement[m³]
Energie [kWh] 12 13 14 14 15 16 16 15 15 13 12 12 14
Rayonnement [kWh/m²] 4,3 4,7 4,9 5,0 5,2 5,7 5,7 5,3 5,1 4,5 4,3 4,1 4,9
Pluviométrie [mm] 5,5 4,4 5,5 5,5 2,9 0,57 0,70 2,4 5,2 6,6 7,2 6,0 4,4
Temp. ambiante [°C] 25 25 25 25 26 28 28 29 27 25 25 25 26
Val. horaires 6:00 7:00 8:00 9:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00
Rendement[m³/h]
Energie [kWh] 0,010 0,42 0,90 1,3 1,6 1,8 1,9 1,8 1,6 1,3 0,87 0,41 0,010
Rayonnement [kWh/m²] 0,003 0,14 0,30 0,46 0,57 0,65 0,67 0,65 0,57 0,46 0,30 0,14 0,003
Temp. ambiante [°C] 21 21 22 24 26 28 30 31 31 31 31 30 30
Remarque: IngunduBangabangaIntshem Labwe
SunSwitch conditions requises de réglage min. 15 %
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
1/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_120m
Projet de pompage solaire
-
�aractéristique du système
Min. 800 � /m�� 20 �� Ma�./S���
�énérateur PV Température des cellules [°C] 46 25
Perte de température [%] 8,8 -
Perte par saletés [%] 5,0 -
Pmax [Wp] 2.285 3.300
Vmp [V] 189 207
Imp [A] 12 16
Voc [V] 227 250
Isc [A] 13 17
Pout [W] 1.325 -
Vout [V] 219 -
Iout [A] 6,1 -
���le moteur Perte de puissance [%] 3,2 3,2 9,8
Systèmes de pompe Puissance du moteur [W] 345 1.265 1.265
Tension du moteur [V EC] 61 210 210
Intensité du moteur [A] 5,7 6,1 6,1
Vitesse du moteur [rpm] 902 3.275 3.275
Débit [m³/h] 0,31 2,5 2,5
Efficacité [%] 27 61 61
*STC: Modules photovoltaïques en condition de test standard, rayonnement 1 000 W/m², température des cellules 25 °C
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
2/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_120m
Projet de pompage solaire
-
Schéma de �ranchement
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
3/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_120m
Projet de pompage solaire
-
System �ayout
1: PS Controller
2: Submersible Pump
3: Stilling Tube
4: Well Probe
5: Cable Splice Kit
6: Grounding Rod
7: Surge Protector*
8: Safety Rope
9: Water Meter
10: Pressure Sensor
11: Float Switch
12: Sun Switch
13: PV Disconnect
14: Lightning Surge Protector
15: PV Generator
*Il est recommandé d'installer une protection contre les surtensions au niveau de chaque entrée de capteur du contrôleur.
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
4/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_120m
Projet de pompage solaire
-
Si�ing �ayout
� �Perte de pression statique�:
Hauteur verticale du niveau dynamique de l’eau au point de livraison le plus élevé.
� �A�aissement de la nappe phréatique�:
Abaissement de l’eau dépendant du débit et taux de récupération du puit.
D �Diamètre intérieur de la canalisation �� ��ongueur du tuyau�: Canalisation entière de la sortie de la pompe au point de livraison. Des coudes et armatures doivent être ajoutés
comme longueur de canalisation équivalente.M ����le moteur�: Câble entre le contrôleur et la pompe.
� �Angle d�inclinaison �: Angle entre le panneau du générateur PV et le panneau horizontal.
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
5/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_120m
Projet de pompage solaire
-
Chute max. 180 mDébit max. 2,6 m³/h
�ontr�leur PS4000▪ Entrées de commande pour protection contre le fonctionnement à sec, commande à distance, etc.▪ Protection contre inversion de polarité, surcharge et surchauffe▪ MPPT (Maximum Power Point Tracking) intégré
Puissance max. 4,0 kWTension d'entrée max. 375 VOptimal Vmp** > 238 VIntensité du moteur max. 15 AEfficacité max. 98 %Temp. ambiante -30...50 °CClasse de protection IP65
Moteur ��DR�V� 4000��R▪ Entretien minimal, moteur DC sans balais ▪ Rempli d'eau▪ Matériel de haute qualité, acier inoxydable: AISI 304/316▪ Moteur sans électronique à l'intérieur Puissance nominale 4,0 kWEfficacité max. 92 %Vitesse du moteur 900...3.300 rpmClasse d'isolation FClasse de protection IP68Submersion max. 150 m
��trémité de la pompe P� �R�14�����▪ Clapet anti-retour ▪ Matériel de haute qualité, acier inoxydable: AISI 304/316▪ En option : protection contre le fonctionnement à sec ▪ Helical rotor pump
Normes2006/42/EC, 2004/108/EC, 2006/95/EC
IEC/EN 61010-1:2010, IEC 62103:2003, IEC/EN 60034-1:2010,IEC/EN 60335-2-41:2003+A1+A2,IEC/EN 60335-1:2012, EN 62233:2008IEC/EN 61000-6-4:2007+A1, IEC/EN 61000-6-2:2005
IEC/EN 61702:1995, IEC/EN 62253 Ed.1
Les logos indiquent les autorisations obtenues pour cette gamme de produits. Les produits sont commandés et livrés selon les autorisations propres aux exigences du marché.
Pompe P�4000 �R�14�� �Moteur� ��trémité de la pompe�Diamètre de forage min. 4,0 inTempérature de l'eau max. 50 °C
Données techniques
�amme de systèmes
* PS DataModule est inclus dans tous les contrôleurs PSk2 et n'importe quel contrôleur PS avec -D dans sa description. Les variantes -D devraient être commandées s'il y a un besoin potentiel d'utiliser les caractéristiques du PS DataModule à l'avenir, comme il n'y a pas d'option de montage ultérieur.
**Vmp: Tension MPP en condition de test standard (STC) : rayonnement solaire 1 000 W/m², température des cellules 25 °C ***Préciser la plage de température à la commande
PS DataModule - enregistreur de données intégré et caractéristiques de gestion de pompe avancées. Permet la configuration simple du système, données en temps réel et enregistrées et en plus fournit la communication Bluetooth au PumpScanner Android ™ App et PS Communicator.*
��RN� �OR�N�� �m�� � �o. ��Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany, Tel +49 (0)4193 8806-700, www.lorentz.de
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.Les photos peuvent varier des produits réels selon les exigences et les réglementations du marché local.
Système de pompe solaire immergée pour puits 4� PS4000 �R�14��
-
H =H2 =W1 =W2 =W3 =
D =D1 =
595 mm563 mm178 mm156 mm116 mm165 mm150 mm
�ontr�leur
A =B =C =D =E =S =
913 mm245 mm668 mm96 mm147 mm1,25 in
Pompe ��
Poids net
Contrôleur 9,0 kg
Pompe 16 kg
Moteur 10 kg
Extrémité de la pompe 5,5 kg
*Vmp: Tension MPP en condition de test standard (STC) : rayonnement solaire 1 000 W/m², température des cellules 25 °C **En taillant les rondelles en caoutchouc, le diamètre peut être réglé entre 6" et 4".
Dimensions et poids
�raphique de la pompe Vmp* > 238 V
��RN� �OR�N�� �m�� � �o. ��Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany, Tel +49 (0)4193 8806-700, www.lorentz.de
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.Les photos peuvent varier des produits réels selon les exigences et les réglementations du marché local.
Système de pompe solaire immergée pour puits 4� PS4000 �R�14��
-
��RN� �OR�N�� �m�� � �o. �� Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
Well Probe Mechanically Activated Device for Dry Run Protection in Applications with LORENTZ Solar Pump Systems
The switch can be used to detect the water level within a well. When the water level in the well dropped below the level of the well probe, the LORENTZ Controller will stop the pump and indicates Source Low LED.
ORDER INFORMATION
Item no.: 19-000000 product name: Well probe sensor
FEATURES
Reliable dry run protection Simple to install Trouble free operation Corrosion-free Splicing kit included
TECHNICAL DATA
Max. operating temperature 55 °C Enclosure class: IP68
Submersion depth: max 50 m Cable length: 1.5m Wire size: 2x 0.75mm² or AWG 19,
waterproofed Mounted in vertical position Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 260 x 170 x 40 mm 10.3 x 6.7 x 1.6 in
Total weight: 0.1 kg / 0.2 lbs
-
��RN� �OR�N�� �m�� � �o. �� Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
Float Switch Mechanically Activated Device for Water Level Detection in Applications with LORENTZ Solar Pump Systems
The switch can be used to detect the water level within a tank. When the water level in the tank reaches the maximum, the LORENTZ Controller will stop the pump and indicates Tank Full LED.
ORDER INFORMATION
Item no.: 19-000030 product name: Float Switch
FEATURES
N.O. (normally open) and N.C. (normally closed) function Reliable water level detection Simple to install Trouble free operation Not sensitive to rotation Corrosion-free
TECHNICAL DATA
Operating temperature: -10°C to 55°C Storage temperature: : -10°C to 55°C Enclosure class: IP68 Cable length: 3m, waterproof Wire size: 3x 1.0mm² or AWG 18 Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 230 x 160 x 55 mm 9.1 x 6.3 x 2.2 in
Total weight: 0.8 kg / 1.8 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
SunSwitch Automatic Solar Level Switching Device
The SunSwitch can be used for any application where you need to switch depending on the solar intensity. It is an autonomous working unit that supplies itself with power from the PV-module on its rear side.
ORDER INFORMATION
Item no.: 19-000050 product name: SUN SWITCH Light-Sensor
FEATURES
Trouble free operation Pump will only run when minimum flow rates or
pressure levels can be achieved which are required by certain applications
Reduced wear on the pump and motor since the pump only starts when it will continue to run
TECHNICAL DATA
Contact rating: Max. voltage 250 VAC / 220 VDC Max. current 2A Max. power 60 W / 62.5 VA
Enclosure class: IP54 Cable length: 4 m Wire size: 3x 1.0mm² or AWG 18, waterproofed Mounted close to the solar array Manual with further informations
is available in PartnerNet Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 230 x 115 x 90 mm 9.1 x 4.5 x 3.5 in
Total weight: 1.2 kg / 0.6 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
Surge Protector Device to Protect LORENTZ Pump Accessories from Voltage Spikes
ORDER INFORMATION
Item no.: 19-000280 product name: Surge Protector
FEATURES
Reliable surge protection for all LORENTZ pump accessories
Can be installed inside the PS Controller
TECHNICAL DATA
Max. voltage: 14 VDC Max current 8/20μs: 500 A Enclosure class: IP65 Ambient temperature: max. 50°C Wire size: 2x 1.5mm² or AWG 16 Meets the requirements for CE
DIMENSION/WEIGHT
Packing dimensions: 70 x 45 x 20 mm 2.8 x 1.8 x 0.8 in
Total weight 0.1 kg / 0.2 lbs
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations
V15
0528
PV Disconnect 440-40-6 Connection box with DC Disconnect Switch and optional lightning surge protection
ORDER INFORMATION Item no.: 19-000136 product name: PV Disconnect 440-40-6 Item no.: 19-002120 product name: MNSPD-115 Item no.: 19-002130 product name: MNSPD-300 Item no.: 19-002140 product name: MNSPD-600
Lightning surge protectors must be ordered separately
FEATURES
Designed for PS150 – PS4000 For professional installation of pumping
systems
TECHNICAL DATA
Wiring up to 6 PV-strings in parallel DC rated disconnect switch enclosed Enclosure class IP 54 Meets the requirements for CE
PV Disconnect 440-40-6 Max. voltage 440 V DC
Max. current per string 10 A
Max. total current 40 A
Max. no. of strings 6
String cable size 2,5 - 4mm²
Output cable size 4 - 10mm²
Optional lightning surge protector
Connects through an existing mounting hole in the PV connect housing
Proper grounding of the device is manda-tory to achieve protection
Controller MidNite surge protector PS150 – PS200 MNSPD115
PS600 – PS1800 MNSPD300
PS4000 MNSPD600
DIMENSION/WEIGHT [mm]
Optional lightning protection
Net. Weight: 2,15kg (+0,35kg)
Optional lightning protection
PG cable glands (2x PG11 13x M16)
Optprot
Mounting hole (1x PG16 cap)
-
BERNT LORENTZ GmbH & Co. KG Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on local market requirements and regulations.
V15
0528
PP4000 AC PowerPack AC/DC Converter to Supply PS4000 Pump Systems with Backup Power from a Generator or Mains Supply
ORDER INFORMATION
Item no.: 19-000180 product name: Power Pack 4000
TECHNICAL DATA
3-Phase AC input: 380V (±20 %), 45 to 65Hz DC output: 190-286V, 5.7kW DC output rated current: 20A @ 230V DC Must be protected from direct mid-day sun IP42 Ambient temperature: –5 to 45°C Efficiency up to 94% Passive cooling, no fan All wires must be #14 AWG (2.5 mm²) or larger Manual with further informations
is available in PartnerNet Meets the requirements for CE
DIMENSION/WEIGHT
Packaging dimensions: 332 x 210 x 202 mm 15.7 x 8.7 x 8.3 in
Total weight: 14.5 kg / 30 lbs
-
BERNT LORENTZ GmbH & Co. KGSiebenstuecken 24, 24558 Henstedt-Ulzburg, Germany, Tel. +49 (0) 4193 8806 - 700
Errors excepted and possible alterations without prior notice. Pictures may differ from actual products depending on local market requirements and regulations. A pump system consists of a controller, motor and pump end. Multiple pumps/pump ends are shown to represent the wide range of pumps (over 70) that LORENTZ has.
To fi nd out more visit www.lorentz.de
151118
LC150-P36 High-efficiency PV Module
Features
high energy yields ensured by high conversion efficiency
sturdy, clear-anodized aluminum frame with pre-drilled holes for quick installation
advanced EVA encapsulation with triple-layer backsheet, meets the most stringent safety requirements for high-voltage operation
pre-wired junction box equipped with connec-tors ”plug‘n‘play“
reliable bypass diodes to prevent overheating (hot spot effect) and to minimise power loss by shading
manufactured in ISO 9001:2000-certified factory
Specifications
Electrical Data
Peak power Pmax [Wp] 150
Tolerance [%] + 5/0
Max. power current Imp [A] 7.98
Max. power voltage Vmp [V] 18.8
Short circuit current Isc [A] 8.5
Open circuit voltage Voc [V] 22.7
Temperature co-efficient for Pmax [%/°C] -0.42
Temperature co-efficient for Voc [%/°C] -0.34
Temperature co-efficient for Isc [%/°C] 0.06
Max. system voltage [VDC] 1,000
Module efficiency [%] 14.94
Practical module efficiency [%] 17.12
All technical data at standard test condition: AM = 1.5, E = 1,000 W/m², cell temperature: 25 °C
Cells
Number of cells in series 36
Number of cells in parallel 1
Cell technology polycrystalline
Cell shape rectangular
Warranty
Warranty: 2 years
Performance guarantee: up to 10 years (90% power output) up to 20 years (80% power output)
Details according to warranty issued by LORENTZ
phot
o m
ay d
iffer
from
act
ual p
rodu
ct
Standards
LC150-P36 is certified according to IEC 61215 and 61730 by TÜV Rheinland and meets the requirements for CE.
• Qualified, IEC 61215• Safety tested, IEC 61730• Periodic Inspection
-
BERNT LORENTZ GmbH & Co. KGSiebenstuecken 24, 24558 Henstedt-Ulzburg, Germany, Tel. +49 (0) 4193 8806 - 700
Errors excepted and possible alterations without prior notice. Pictures may differ from actual products depending on local market requirements and regulations. A pump system consists of a controller, motor and pump end. Multiple pumps/pump ends are shown to represent the wide range of pumps (over 70) that LORENTZ has.
To fi nd out more visit www.lorentz.de
151118
Electrical Performance
Physical Specifications mm
Cell temperature [°C] Irradiance [W/m2]
0 10 20 30 -25 0 +25 +50 +75 100 0 200 400 600 800 1000 1,200 0 10 20 30
Curre
nt [A
]
Curre
nt [A
]
Nor
mal
ised
Isc, V
oc a
nd P
max
(%)
Nor
mal
ised
Isc, V
oc a
nd P
max
(%)
75°C
Isc
Isc
VocVoc
Pmax
Pmax
25°C
50°C4 4
7 7
5 5
8 8
3 3
6 6
9 9
2 2
1 1
80 80
100 100
120 120
140 140
60 60
40 40
20 20
0 00 0
Weight [kg] 12.0
Dimension [mm] 1,492 × 673 × 40
Strength [N/m2] 2,400
Cable approx. 900 mm, 4 mm2
Connectors MC4 PV-KBT4/6II-UR / PV-KST4/6II-UR
Electrical Performance
for different temperatures, at AM=1.5, E=1,000 W/m2
Electrical Performance
for different irradiation, at 25 °C
Temperature Dependence
of Isc, Voc and Pmax
Irradiation Dependence
of Isc, Voc and Pmax at 25 °C
Voltage [V]
1,000 W/m2
800 W/m2
600 W/m2
400 W/m2
200 W/m2
Voltage [V]
1,49
2 [5
8.7]
712
[28]
1,21
2 [4
7.7]
40 [1.6]
Ø 4
9 ×14
9 ×14
35 [1.4]
10 [0.4]
40 [1
.6]
673 [26.5] 623 [24.5]
A‘A A‘AA‘A
A‘A
A‘
A
-
ParamètreEmplacement: Congo (Dem. Rep.), Idiofa (5° Sud; 20°
Est)Température de l'eau:
25 °C
Rendement quot. requis:
20 m³; Dimensionnement pour mois moyen
Perte par saletés: 5,0 % Câble moteur: 150 m
Type de tuyau: - Hauteurmanométrique :
140 m Longueur du tuyau: -
Produits Quantité DétailsPS4000 HR-14HL-2 -D 1 pce Système de pompe immergée comprenant contrôleur avec DataModule, moteur et extrémité de
pompeLC150-P36 26 pce 3.900 Wp; 13 x 2 modules; 15 ° incliné
Câble moteur 150 m 4 mm² Câble triphasé pour le courant et câble monophasé pour la mise à la terre
Accessoires 1ensemble
Well Probe, Float Switch, SunSwitch, Surge Protector, PV Disconnect 440-40-6, PP4000 AC PowerPack
Rendement quotidien en mois moyen 20 m³
Val. quotid. Jan Fév Mar Avr Mai Jui Jui Aoû Sep Oct Nov Déc Moy.
Rendement[m³]
Energie [kWh] 15 16 17 17 18 19 19 18 17 15 15 14 17
Rayonnement [kWh/m²] 4,3 4,7 4,9 5,0 5,2 5,7 5,7 5,3 5,1 4,5 4,3 4,1 4,9
Pluviométrie [mm] 5,5 4,4 5,5 5,5 2,9 0,57 0,70 2,4 5,2 6,6 7,2 6,0 4,4
Temp. ambiante [°C] 25 25 25 25 26 28 28 29 27 25 25 25 26
Val. horaires 6:00 7:00 8:00 9:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00
Rendement[m³/h]
Energie [kWh] 0,012 0,50 1,1 1,6 1,9 2,2 2,2 2,1 1,9 1,5 1,0 0,48 0,012
Rayonnement [kWh/m²] 0,003 0,14 0,30 0,46 0,57 0,65 0,67 0,65 0,57 0,46 0,30 0,14 0,003
Temp. ambiante [°C] 21 21 22 24 26 28 30 31 31 31 31 30 30
Remarque: Impini InsiMayanda MusangaPunkulu
SunSwitch conditions requises de réglage min. 15 %
Créé par LORENTZ COMPASS 3.1.0.65Toutes les caractéristiques techniques et informations sont fournies de bonne foi. Un risque d’erreur existe et les produits peuvent être modifiés sans préavis.
1/5
Siebenstücken 24D-24558 Henstedt-Ulzburgwww.lorentz.de
Bayrem Matmati
Tél.: +49 (0) 4193 8806 - 723Fax: +49 (0) 4193 8806 - [email protected]
BERNT LORENTZ GmbH & Co. KG
vendredi 11 mars 2016
20m³/jour_140m
Projet de pompage solaire
-
�aractéristique du système
Min. 800 � /m�� 20 �� Ma�./S���
�énérateur PV Température des cellules [°C] 46 25
Perte de température [%] 8,8 -
Perte par saletés [%] 5,0 -
Pmax [Wp] 2.705 3.900
Vmp [V] 223 244
Imp [A] 12 16
Voc [V] 269 295
Isc [A] 13 17
Pout [W] 1.550 -
Vout [V] 258 -
Iout [A] 6,1 -
���le moteur Perte de puissance [%] 4,1 4,1 12
Systèmes de pompe Puissance du moteur