presenacion bombas wilden.pdf
TRANSCRIPT
-
EJEMPLO DE AJUSTE Y CONFIGURACIN DEL SISTEMA SME Pro-Flo X
BARCELONA c/ Marina, 131 Bis 133 08013 Barcelona Telf.: 902 901 498 Fax: 902 947 822 [email protected] c/Cabo de Trafalgar 2 28500 Arganda del Rey (Madrid) Telf.: 918 757 656 Fax: 918 757 657 [email protected]
www.tecnicafluidos.com
-
Pro-Flo X
-
Pro-Flo X
En el pasado, Wilden Pump decidi que era mas importante Caudal y Consumo de aireque Eficiencia.
Pro-Flo X El cliente Decide lo que mas le interesa
El Sistema de mantenimiento de eficiencia(SME) Permite Optimizar lasprestaciones de la bomba para cadaAplicacin.
-
Posiciones SME El cliente puede ajustar el SME del 4 al 1
Posicin 4 Mximo Caudal Posicin 1 Mxima Eficiencia
-
Como trabaja El SME Varia el paso de entrada de aire
Ms paso de aire Ms caudal Menos paso de aire Aumentamos Eficiencia
-
Pro-Flo X Prestaciones La curva del manual EOM es la curva Setting 4 La misma curva tradicional
Todas las bombasPro-Flo X salen de fabrica ajustadas en Setting 4
NOTA: LAS CURVAS SON SOLO DE EJEMPLO Y NO SE CORRESPONDEN CON LA BOMBA OFERTADA
-
Pro-Flo X Performance Curves
Nuevo Efficiency Management System (EMS) Curve Solo para Pro-Flo X EMS Curva utilizada para otro ajuste distinto de el ajuste 4
El EMS tiene 3 distintosajustes 1, 2 & 3.
Ajustar otro sistintotambien puede ser interpolado (Ejpm., 1.5)
Setting 1.5Flow Air
-
Pro-Flo X Curvas 2 factores X Distintos:
Xflow Caudal Xair Consumo de aire
Las curva EMS consisteen dos curvassuperpuestas una sobreotra :
- Flow ( Caudal )
- Air ( Aire )
-
Pro-Flo X Curvas El Factor X es Multiplicado por otros Ajustes
FlowEMS Setting 4 XFlow = FlowEMS Setting n AirEMS Setting 4 XAir = AirEMS Setting n
Cada EMS ajuste tiene 2 factores X :
- XFlow- XAir
-
Pro-Flo X Curvas Dos Curvas
Curva tradicional Setting ( Ajuste ) 4 Curva EMS Settings ( Ajustes ) distintos del 4
Dos Factores X por cada Ajuste EMS Flow ( Caudal ) Air ( Aire )
Factores X son multiplicados
-
EJEMPLO
30
103
77
0.620.48
Paso 1)
Condiciones de Operacin: Presin de descarga: 30-psig ( 2 Bar )Presin de entrada de Aire: 80-psig ( 5.5 Bar )
Caudal: 103-gpm ( 389,89 LPM )
Consumo de Aire: 77-scfm ( 131 Nm/h )Obtener el punto de rendimiento
En el ajuste 4 ( Setting 4 )
EMS Ajustado en el 2 (Setting 2)
Paso 2) Obtener el factor X en el ajuste 2
( Setting 2 )
Caudal Factor X :Aire Factor X :
0.620.48
-
EJEMPLO
30
103
77
0.620.48
Paso 3)Obtener caudal en el ajuste 2
( Setting 2 )
103-gpm( 389,89 LPM )
0.62 = 64-gpm (242,26 LPM )
Ajuste de Caudal en
el 4
Factor X de Caudal en ajuste 2
Paso 4)Obtener consumo de aire en el ajuste 2
( Setting 2 )77-scfm
(131 Nm/h )
0.48 = 37-scfm ( 62,95 Nm/h )
Ajuste de consumo de aire
en el 4
Faxtor X de consumode aire en ajuste 2
El Caudal fue reducido un 38%, Pero el consumo de aire fue reducido un 52%!
Continuacin.
-
Example 2
142
Step 5)
2-in Sandpiper Pump:
Since Point is Between Settings, the Actual EMS Setting Must be Interpolated:
100-psig inlet airHow much will air consumption be reduced by installing and optimizing a Pro-Flo fitted pump in an application using a competitor pump?
Step 4) Using Head Pressure & Flow X Factor From Step 3 Locate Point on EMS Curve2.9
20-psig head 116-gpm 130-scfm air consumption
0.82
Setting 2.9
Continued
The EMS can now be set to 2.9 and the Pro-Flo Xflow will match the Sandpiper pump.
-
Example 2
142
2-in Sandpiper Pump:
Step 6) Using the Interpolated EMS Setting, Determine the Air X Factor:
100-psig inlet airHow much will air consumption be reduced by installing and optimizing a Pro-Flo fitted pump in an application using a competitor pump?
0.72
20-psig head 116-gpm 130-scfm air consumption
0.82
Setting 2.9
0.72
Step 7) Obtain Air Consumption At Setting 4: 109-scfm
109
Continued
-
Example 2
142
Step 8)
2-in Sandpiper Pump:
Multiply the Setting 4 Air Consumption By the Air X Factor to Obtain Actual Air Consumption
100-psig inlet airHow much will air consumption be reduced by installing and optimizing a Pro-Flo fitted pump in an application using a competitor pump?
20-psig head 116-gpm 130-scfm air consumption
0.82
Setting 2.9
0.72
109-scfm 0.72 = 78-scfm
Air Consumption at Setting 4
Air X Factor at Setting
2.9
109
The customer could reduce air consumption 40% (52-scfm) by replacing the Sandpiper pump with an optimized Pro-Flo X pump!
Continued