professional instruments - r.b.m. ltd€¦ · and owingen, we are offering an extensive product...
TRANSCRIPT
A subsidiary of
www.ghm-messtechnik.de
Professional InstrumentsMade in Germany
Made in Germany
SIL 2
Hiermit wird bestätigt, dass die
Inhaber des Zertifikates Nr. FS 528548/2985D
ein Qualitätsmanagementsystem gemäß DIN EN ISO 9001:2008 für den folgenden Geltungsbereich anwendet:
Für und im Namen von BSI:
Geschäftsführung, BSI Management Systems (Deutschland)
Ursprünglich zertifiziert: 12.01.1996 Letzte Ausgabe: 05.05.2010 Ablaufdatum: 23.05.2012
GHM Gruppe vertreten durch die GHM Messtechnik GmbH Hans-Sachs-Straße 26 93128 Regenstauf Deutschland mit den im Anhang aufgeführten Unternehmen
Entwicklung, Fertigung und Vertrieb von mess-, steuer- und regeltechnischen Komponenten für industrielle Anwendungen
Dieses Zertifikat wurde elektronisch erstellt und bleibt Eigentum der BSI und ist an die Vertragsbedingungen gebunden. Ein elektronisches Zertifikat kann online beglaubigt werden. Kopien können auf www.bsigroup.de/de/Audit-und-Zertifizierung/138880/ oder per Telefon +49 (0) 6181 99370 validiert werden. Die British Standards Institution ist eingetragen in die Royal Charter. BSI Management Systems und Umweltgutachter Deutschland GmbH, Dörnigheimer Straße 2a, 63452 Hanau, Deutschland.
QUALITÄTSMANAGEMENTSYSTEM – DIN EN ISO 9001: 2008
QMS/EMS-TGA-ZM-08-92
Seite: 1 von 2
Zertifikat
Hiermit wird bestätigt, dass die
Inhaber des Zertifikates Nr. FS 528548/2985/2D
das Qualitätsmanagementsystem der GHM Gruppe, Zertifikat Nr. FS 528548/2985D, gemäß DIN EN ISO 9001:2008 für den folgenden Geltungsbereich anwendet:
Für und im Namen von BSI:
Geschäftsführung, BSI Management Systems (Deutschland)
Ursprünglich zertifiziert: 12.01.1996 Letzte Ausgabe: 05.05.2010 Ablaufdatum: 23.05.2012
Honsberg Instruments GmbH Tenter Weg 2-8 42897 Remscheid Deutschland
Entwicklung, Fertigung und Vertrieb von mess-, steuer- und regeltechnischen Komponenten für industrielle Anwendungen
Dieses Zertifikat wurde elektronisch erstellt und bleibt Eigentum der BSI und ist an die Vertragsbedingungen gebunden. Ein elektronisches Zertifikat kann online beglaubigt werden. Kopien können auf www.bsigroup.de/de/Audit-und-Zertifizierung/138880/ oder per Telefon +49 (0) 6181 99370 validiert werden. Die British Standards Institution ist eingetragen in die Royal Charter. BSI Management Systems und Umweltgutachter Deutschland GmbH, Dörnigheimer Straße 2a, 63452 Hanau, Deutschland.
QUALITÄTSMANAGEMENTSYSTEM – DIN EN ISO 9001: 2008
QMS/EMS-TGA-ZM-08-92
Seite: 1 von 1
Zertifikat
A subsidiary of
Quality "Made in Germany"
The GHM Messtechnik companies develop and manufacture all devices and systems exclusively in Germany. With the merger, the product portfo-lio increased significantly.Well-known corporations appreciate our quality "Made in Germany".
Synergies
Following the merger of the companies GREISINGER electronic, Honsberg Instruments and Martens Elektronik in 2009, GHM Messtechnik was established, thus providing enhanced competence for all aspects of measurement and indus-trial electronics. In March 2010, Imtron Messtechnik was integrated as fourth company into the GHM group.
With approx. 200 employees and more than 30 developers at the four locations Regenstauf, Remscheid, Barsbüttel and Owingen, we are offering an extensive product portfolio for the requirements of the following segments:
Laboratory Measurement Industrial Electronics Process Engineering Industrial Measurement Test Bench Measurement
Our sales network with eight sales engineers covering whole Germany, provides excellent technical support. Fur-thermore there is a world-wide presence with GHM sales subsidiaries in the Czech Republic and the Netherlands, as well as sales representatives and representations all over Europe, North and South America, Asia, and Africa.
Our Ambition - Your Advantage
As a specialist and full-range supplier of measurement technology we develop customized and market-driven solutions for you, matching the high demands of the industry.
State-of-the-art 3D CAD systems for development of inhouse and customer-specific products.
Flexibility and Innovation
These two terms belong together and are the driving force behind the success of GHM Messtechnik.
We find solutions for the requirements of our customers in addition to the substantial standard program.
Shielded EMC chambers for all necessary testing
Pressure test up to 1000 bar
State-of-the-art Altium 3D layout
Just ask us ...
Competence in Measurement Technology
Our products meet all special standards:
• DIN EN ISO 9001 standard for quality management systems
• Safety Integrity Level (SIL2)• DIN EN 14597• Ex-Approval according to ATEX
• Classification of shipping GL (Germanischer Lloyd)
• EC-Certificate of conformity• etc.
Test bench for IP protection rating
pH
Redox
°C
µS/cml/minm³/h %r.F.°Fbar
A subsidiary of
Portfolio of the GHM Group
Laboratory Measurement
Handheld Instruments
Cond
uctiv
ity
Tem
pera
ture
Humid
ityPr
essu
re
pH /
ORPSe
nsor
s
Industrial Electronics
Displa
ys /
Cont
rolle
rIso
latin
g co
nver
ters
Mea
sure
men
t tra
nsm
itter
sSw
itchi
ng re
lays
Mon
itorin
g re
lays
Data
logg
er /
EASY
Bus
. . . p r o f e s s i o n a l I n s t r u m e n t s " M a d e i n G e r m a n y "
Test Bench Measurement CustomizingIndustrial Measurement
Flow
Tem
pera
ture
Pres
sure
Humid
ity
Leve
l
Filtr
atio
n
Process Engineering
Flow
Tem
pera
ture
Cond
uctiv
ity
Leve
l
pHPres
sure
S k i l l s i n M e a s u r e m e n t , C o n t r o l a n d P r o c e s s Te c h n o l o g y
NEW
A subsidiary of
Process measurement technology for hygienic areas
Process connections
Temperature (configurable via GTL programming tool)
Level measurement
Demands on the measuring technology
The basis of hygienic process control and therefore the demands on the measuring technology is essentially the fulfillment of the following
criteria:
� Hygienic Design for uncritical application� CIP- / SIP cleanable� Sensors made of stainless steel� FDA conform materials� EHEDG certification � 3A-approval� Protection class IP67 / IP69K
The process adaption demands choosing a hygienic process connection conforming to standards according to the desi-red application at tanks or in tubes. Diameter, volume and design define size and type of the connection, and medi-um, temperature and pressure state possible measuring principle. We offer hygienic easy-to-clean standard and special process connections for each measuring principle.
The temperature sensor series of the GHM group includes more than 30 different basic design types. The versatile probes cover a huge range of applications in food, bevera-ge and pharmaceutical industry.
Advantages
� Temperature range -40...+200 °C � Optional head transmitter� Fast response time due to reducing measuring tip� Several adapters and weld-in sleeves� Several evaluations electronics (ATEX, Profibus, SIL 2)� Pipe sensors for temperature monitoring of cleaning
and sterilization processes and for pasteurization and UHT
� Hydrostatic level measurement The level measurement is traced back to a measurement of
the hydrostatic pressure. This pressure is caused by the liquid column above the sensor and is directly proportional to the
filling level.
� Potentiometric level measurement (single rod probe)The level of free-flowing media is measured by a single rod probe.
Exploiting the electric induction the reference pole has been moved into the probe, thus no electric connection at the tank is necessary any
more.
Limit level measurement (configurable via GHMware)
Flow rate
Analysis measurement technology (configurable via GHMware)
� Capacitive DC measuring deviceThe DC measuring device provides measuring and monitoring of the dielectric constant (DC) of products. This allows monitoring of e.g. oil-water emulsion. A freely scalable current output is integrated for outputting the measuring value. The current status of the device and the measuring value can every time be read on the LC-display.
Applications� Media separation / monitoring of emulsions� Continuous process control / product quality monitoring via DC
� Capacitive measuring principleSeveral years of experience with different kinds of level sensors and limit level switches finally resulted in a new measuring principle. Striking advantages of this patented charge transfer measuring principle are the re-sponse time, setting of switching points to the digit and the possibility of phase varia-tion of media (e.g. milk and water).
� Calorimetric measuring principleThe limit level switch can detect liquids irrespective of conductivity or coloring. Ad-ditionally not too coarse granulate or mud-like products can be detected.
� Conductive measuring principleThis is a very cost-effective and flexible method for limit level detection. The sensor can be designed as single-rod as well as multi-rod probe. The sensor rods can subsequently be shortened or bent to fit them to the installation situation.
� Calorimetric flow rate measurementThe electronic flow rate monitoring based on the calorimetric principle has no mecha-nically moving parts (e.g. no turbine wheel or floating element). Therefore the sensor ca be used for media containing solids.Application: Monitoring and measuring of (even very low) flow rates, leakage control.
� Magnetic-inductive flow rate measurementThe magnetic-inductive principle uses the effect of conducting liquids inducing a voltage proportional to the flow velocity in a solenoid. Advantages of this measuring principle are that no moving parts are necessary and the pressure loss due to the mea-surement is low. Depending on the demands on design and tube standard the sensors are adaptable by several process connections.
Advantages� Compact design� Completely made of stainless steel� Operation without having to open
the housing� Graphic LCD, background illumination
� 14 diameters 3..100 mm� Variable process connection� Voltage supply 24 V DC� EHDGE + 3A approval
A subsidiary of
Brief overview: products with Ex
EU-Directive / CE mark
The explosion protection is regulated by directives and laws within the European Union. Electric devices have to fulfill corresponding regula-
tions in the EU. If the requirements are fulfilled, the manufacturer can label the device with the CE mark. In this context any misuse is an
offense.
According to directive 94/9/EG (ATEX directive) this marking is supplemented for the explosion protection of certain device classes – if needed – with the number of the notified body that performed the acceptance of the quality management.
In contrast to non-EU laws,the ATEX directive also applies to non-electric (e.g. pneumatic actuators). Corresponding sys-tems and facilities are classified “requiring inspection” and only devices approved for that purpose are allowed to be used. Furthermore start-up, changing and routine safety inspections have to be certified by state-approved insti-tutions or corporations. The legal framework are the EU directives, which are bindingly enacted for all EU member countries.
Explosions
Generally, there have to be three factors fulfilled, that a explosion can take place at atmospheric air:
• combustible• oxygen (air)• ignition source
Labeling according to directive 94/9/EGGeneral labeling according to EN 60079-0
II 2G Ex d IIC T6
Explosion- proof equipment
Explosion- proof equipment
Device group
Category Type of ignition protection
Explosion group
Temperature class
LabelingExample: Labeling of explosion-proof electric components according to directives 94/9/EG and EN 60079-0:
Industrial sensor and measuring technology
B1. Temperature
B2. Flow rate
B3. Level measurement
B6. Pressure
B7. Weighting technology
E3. Isolation amplifiers
E4. Safety and monitoring devices
GTF 101-ExGTF 102-ExGTF 103-ExTC293TR293TC296
A-V1A-V2A-V3A-H1.1A-H1.2A-H2.1A-U1-1
A-U1-2IL10
IS20IS21
PC22SB8RC3DMS50Ex
Industrial electronics
PMT50Ex-1
TV500Ex, ST500ExTV501ExTS500-Ex
MR50ExSTL50Ex
Laboratory and hand-held measuring devices
GMSD-exMSD-exGMH 3111-exGMH 3151-exGMH 3156-exGMH 3161 - ... - exGMH 3181 - ... - ex
E2. Transmitters
E1. DisplaysGIA 0420 N-exGIA 010 N-exGIA 0420..-exGIA 0420 WK..-exGIA 010 VO..-exGIA 010 WK..-ex
ATEX explosion protection
TR296MU500ExPMT50Ex-2/-3TG50ExSTL50Ex
silverline
A subsidiary of
The first products of GREISINGER electronic GmbH 30 years ago were premium special sensors, which hit the nerve of the market and founded the success of the com-pany.
Since then GREISINGER electronic GmbH has developed and manufactured its handheld instruments, transmit-ters, displays and corresponding sensors in Regenstauf, Bavaria (near Regensburg).
The use of state-of-the-art machinery and instrumen-tation, and the highly efficient and productive manu-facturing process are the the base of the high product quality "Made in Germany" at competitive prices.
. . . p r o f e s s i o n a l I n s t r u m e n t s " M a d e i n G e r m a n y "
Line 3000 Quality for ProfessionalsLine Line COMPACT Switch on and instantly Measure!
In the broad range of GREISINGER handheld instruments you will find the right device for every measurement task.
GREISINGER handheld instruments series Line 3000 are bus-capable, one- or multi-channel devices, have an interface and are optionally available as data logger. Handheld instruments series COMPACT Line can be used wherever fast and precise mea-sured values at economical prices play an important role.
• Temperature• Conductivity• pH / ORP• Pressure• Humidity• Material moisture• Flow• Oxygen• Carbon
monoxide
Handheld Instruments
Line 5000 Waterproof – Line 2000 for highest Demands
• pH / ORP• Temperature• Pressure• Conductivity
With modern design, Greisinger presents the newest handheld instruments with robust and waterproof housing and plug connections / probes.
According to model the handheld instru-ments have cyclic value memory with up to 10000 data set, manual or automatic logger function, an analog output and the large illuminated display.
i.e.: SL-pH
Measuring Sets
Each GHMsilverline set includes a com-plete measuring set � Water-proof handheld instrument� High-quality case� Flash drive with software and manual � USB adapter and cable with connection for analog output� ratis manufacturer's calibration after 1 year with automatic reminding from our calibration laboratory� Accessories like e.g. water-proof pH electrode and buffer solutions or water-proof temperature probe (depending on set type)
• pH / ORP (SL-pH)
• Temperatur (SL-Pt eco)
• Pressure (SL-P)
• Conductivity (SL-C)
A subsidiary of
Data Logger / EASYBus
SMSGSM
Displays / Controller
• Temperature• Humidity• Standard signal• Air pressure• Pulse• Status
- Dimensions 48 x 96 mm 24 x 48 mm
- Universal Inputs• Standard signal• Resistance• Frequency• Speed• Counter• Difference
- Relay switching outputs- Self diagnosis- Programmable characteristic- Transmitter power supply, isolated- Serial Interface- Min/Max value memory
. . . p r o f e s s i o n a l I n s t r u m e n t s " M a d e i n G e r m a n y "
Probes / Signal Converters
• Injection probe• Immersion probe• Surface probe• Air / gas probe• Asphalt probe• Clip-on probe
• Temperature• Humidity• Pressure• Conductivity• ORP• pH• O2• CO• CO2• Flow
Advantages of EASYBus
• Minimum amount of installation and planning• Display and monitoring system for several mea-
surement points• Unrivaled cost/performance ratio • High flexibility: Subsequent modifications and
extensions possible at any time
Applications of EASYBus
• Cooling chambers (temperature monitoring)• Heating / air conditioning / ventilation (tempera-
ture, relative humidity, CO2-monitoring)• Utility rooms / computer rooms / laboratories
(temperature, relative humidity)• Manufacturing rooms (temperature, relative hu-
midity, CO2)
GREISINGER electronic GmbHHans-Sachs-Straße 2693128 RegenstaufGermany +49 (0) 94 02 / 93 83 - 0 +49 (0) 94 02 / 93 83 - [email protected]
Honsberg Instruments GmbHTenter Weg 2-842897 RemscheidGermany +49 (0) 21 91 / 96 72 - 0 +49 (0) 21 91 / 96 72 - [email protected]
IMTRON Messtechnik GmbHCarl-Benz-Straße 1188696 OwingenGermany +49 (0) 75 51 / 92 90 - 0 +49 (0) 75 51 / 92 90 - [email protected]
Martens Elektronik GmbHKiebitzhörn 1822885 BarsbüttelGermany +49 (0) 40 / 6 70 73 - 0 +49 (0) 40 / 6 70 73 - [email protected]
GHM-Greisinger s.r.o.Ovci hajek 2 / 2153158 00 Prague 5 Nove ButoviceCzech Republic +420 251 613 828 +420 251 612 [email protected]
GHM-Meettechniek BVZeeltweg 303755 KA EemnesNetherlands +31 (0) 35 / 5 38 05 - 40 +31 (0) 35 / 5 38 05 - [email protected]
GHM Maaleteknik ApSMaarslet Byvej 28320 MaarsletDenmark +45 64 64 92 - 00 +45 64 64 92 - [email protected]
Competence Center Sales subsidiary
05/2
013GHM Messtechnik GmbH
Hans-Sachs-Straße 2693128 RegenstaufGermany
+49 (0) 94 02 / 93 83 - 0 +49 (0) 94 02 / 93 83 - 33 www.ghm-messtechnik.de [email protected]
. . . p r o f e s s i o n a l I n s t r u m e n t s " M a d e i n G e r m a n y "
GREISINGERe l ec t ron i c