proses drilling

Upload: suardi-hasjum

Post on 02-Mar-2016

101 views

Category:

Documents


2 download

DESCRIPTION

MATERI P.MANUFAKTUR

TRANSCRIPT

  • DRILLING (Proses Gurdi)

  • Defenisiy Penggurdian adalah proses membuat lubang

    dalam sebuah obyek dengan menekankansebuah gurdi berputar kepadanya atau denganmemegang gurdi stasioner dan memutar bendakerja oleh sebuah pencekam.y Gurdi adalah sebuah pahat pemotong yang

    ujungnya berputar dan memiliki dua ataubeberapa tepi potong dan galur yang berhubungan kontinu sepanjang badan gurdi.

  • 3DrillingDrilling is used to create round holes in workpieces using a rotating tool with two cutting edges. This rotating tool is called a drill or drill bit. This operation is normally performed on a drill press. Two types of holes can be made: y through holes, in which the drill exits the opposite side of the worky blind holes , in which the drill does not exit

    (a) (b) Figure depicting (a) through holes and (b) blind holes

  • y Bentuk galur dari gurdi dapat berbentuk lurusatau heliks yang berfungsi sebagai salurantempat lewatnya geram hasil pemotongan danfluida pemotong.y Jumlah galur yang umum adalah dua galur tetapi

    juga terdapat gurdi dengan tiga atau empat galur(Berfungsi untuk meluaskan lubang).y Penggurdi puntir (twist drill) adalah istilah utk

    gurdi dengan dua galur dan dua tepi potong ygdapat dilengkapi dengan tangkai lurus atau tirus.

  • y Penggurdi pistol (Gun Drills) adalah penggurdi ygdigunakan untuk membuat lubang dalam dengangalur lurus yg beroperasi pada hantaran yang jauhlebih kecil dari penggurdi konvensional tetapi dengankecepatan potong yg lebih tinggi.y Gun drills are straight fluted drills which allow cutting

    fluid (either compressed air or a suitable liquid) to be injected through the drill's hollow body to the cutting face. They are used for deep drillinga depth-to-diameter ratio of 100:1 or more is possibley Penggurdi sekop: adalah penggurdi yang digunakan

    untuk membuat lubang dengan diameter yang besar(35-380mm) pada sebuah benda kerja berbentukpelat.

  • Prestasi PenggurdiTerdapat beberapa parameter yang menentukandari sebuah proses drilling (prestasi gurdi) yaitu:y Sudut mata (Point angle).y Sudut Heliks (Helix angle)y Tepi potong (cutting edge)y Fluida Pendingin (coolant)y Kecepatan Potong (CS)y Hantaran (Feed)

  • 7Twist drill bit

  • 11

    Drilling

    The body of a twist drill has two spiral flutes which usually have a 30 helical angle. These flutes act as a passageway for chip extraction from the hole and for coolant to enter the hole.Process:The twist drill is fed into the workpiece while rotating and the relative motion between the cutting edges of the drill and the workpiece results in material removal and, hence, chip formation.

  • 12

    Machining I : Drilling

    The flutes provide enough clearance to allow the chips to be extracted. During drilling, however, friction between the chip and cutting surface (rake face) as well as between the outer diameter of the drill and workpiece generates a large amount of heat and, thus, the temperature of the workpiece and drill increases dramatically.

  • Machining I DrillingTo solve the temperature rise problem, the following is common: Peck drilling: the drill is periodically withdrawn from the

    hole to clear chips Some drills have internal holes in the drill body through

    which cutting fluid is delivered to the cutting interface.Increasing flute size makes it easier to clear chips from the hole

    13

  • 14

    Prior to drilling, centering (or center drilling) is used to create a starter hole (using a center drill). This is used to:

    Define the location of the hole. Solve the Walking or Wandering problem which

    happens because of drill deflection before the chisel penetrates the workpiece.

  • 15

    Machining I DrillingThe following operations are all related to drilling and can be performed once a hole has been created:Reaming: a reamer (usually with multiple straight flutes) is used to ream a hole, i.e., slightly enlarge a hole and improve its surface finish and provide tighter tolerances.Tapping: a tap is used to create internal screw threads on an existing hole. Counterboring generates a stepped hole, i.e., a larger diameter hole is created over a smaller diameter hole. This process is used to seat bolt heads below the surface of a workpiece or flush with the surface.

  • Machining I Drilling

    Operations related to drilling (continued)

    y Countersinking is similar to counterboring, but the hole step is conical and is used for flat head screws. Countersinking is used also for deburring.y Spotfacing is similar to milling. This process is used

    to provide a flat surface on the workpiece.

    16

  • 17

    Machining I Drilling

    The figure below illustrates the various operations related to drilling.

    (a) Reaming(b) Tapping(c) Counterboring(d) Countersinking(e) Center drilling(f) Spot facing

  • y Reaming: proses memperhalus lubang yg sudahdibuat.y Boring: proses memperbesar lubang yg sudah

    aday Counterboring: proses memperbesar ujung

    lubang bisanya untuk baut dan sekrup.y Stepdrill: pembuatan lubang dengan diameter

    bertingkaty Countersinking: Operasi pembuatan taper atau

    bentuk kerucut diakhir lubangy Tapping: proses membuat ulir dalam.

  • Peluas Lubang (Reamer)y Peluas lubang adalah perkakas yang

    menyelesaikan (memperhalus) lubang yang telahdigurdi atau dibor.y Jenis-jenis peluas lubang:1. Peluas lubang tangan: 2. Peluas lubang pencekam3. Peluas lubang cangkang4. Peluas lubang pena tirus5. Peluas Lubang Ekspansi.

  • Jenis-Jenis Mesin Gurdiy Mesin Penggurdi Portable

    Mesin Penggurdi Tegaky Mesin Penggurdi Radialy Mesin Penggurdi turety Mesin Penggurdi Spindel Jamak (gang)y Mesin Penggurdi Otomatis

  • Bagian Utama Mesin Drilly Spindel: Bagian yang menggerakan mata bor.y Drill Head: Bagian yg menopang mekanisme

    pengerak dan menghantarkan kebenda kerja.y Column.y Lengan Radial: bagian dari mesin bor radial yg

    dapat bergerak naik turun maupun putar dimanamotor penggerak dan dril head terpasang kuat.y Meja/Base: bagian yg menopang seluruh bagian-

    bagian mesin dril terbuat dari besi cor

  • Spesifikasi mesin drilly Kecepatan rotasiy Maksimum dan minimum ukuran mata drill yg

    dapat digunakan.y Daya motory Jarak spindel naik dan turuny Jarak maksimum spindel dan mejay Jarak maksimum column ke pusat spindel.

  • 25

    Head

    Forward/Reverse lever

    Column

    Speed adjustment

    Spindle

    Table

  • TUGAS PRESENTASI KELOMPOKy Kelompok I : PROSES DAN MESIN KETAM dan Mesin Serut

    (SHAPER & Planer)(05015,05063,06029,07009,07010,07016,08320)(26/10)

    y Kelompok II:) PROSES DAN MESIN FRIS (MILLING).(08332,09006,09007,09104,09262,09263,09264)(2/11)

    y Kelompok III: PROSES DAN MESIN SAWING(09265,09265,09272,09274,09279,09282,09283)(9/11)

    y Kelompok IV: PROSES DAN MESIN GERINDA.(09286,09287,09290,09291,09301,09302,09303)(16/11)

    y Kelompok V: PROSES DAN MESIN PEMBUATAN RODA GIGI(09310,09311,09316,09317,09318,09321,09322)(23/11)

    y Kelompok VI: PROSES DAN MESIN KEMPA(09324,09326,09332,09334,09336,09337,09338)(30/11)

    Bagi Kelompok yg tidak presentasi pada jadwal ygditentukan tidak memperoleh nilai PRESENTASI(Maks25%)

    DRILLING (Proses Gurdi)DefenisiDrillingSlide Number 4Slide Number 5Prestasi PenggurdiSlide Number 7Slide Number 8Slide Number 9Slide Number 10DrillingMachining I : DrillingMachining I DrillingSlide Number 14Machining I DrillingMachining I DrillingMachining I DrillingSlide Number 18Slide Number 19Peluas Lubang (Reamer)Jenis-Jenis Mesin GurdiBagian Utama Mesin DrillSpesifikasi mesin drillSlide Number 24Slide Number 25TUGAS PRESENTASI KELOMPOK