pt6a engine testing
DESCRIPTION
training modeTRANSCRIPT
PT6A SERIES ENGINE TESTING
2
TABLE OF CONTENT
1. ENGINE TEST FLOW CHART …………………………………………………………………. 3
2. TEST REQUIREMENT AND PROCEDURE MATRIX …………………….……………………. 5
3. LIST OF PT6A PARAMETER AND SYMBOL …………………….……………………. 6
4. TEST PROCEDURE SEQUENCE …………………….……………………. 7
5. ENGINE TEST OPERATING CONDITION LIMIT …………………….……………………. 9
6. ENGINE MOTORING, STARTING AND SHUT DOWN …………………….……………………. 10
7. RUN IN PROCEDURE …………………….……………………. 12
8. ACCESSORIES GEARBOX (AGB) VIBRATION SURVEY …………………….……………………. 13
9. REDUCTION GEARBOX (RGB) VIBRATION CHECK …………………….……………………. 15
10. ACCELERATION AND BODIE CHECK …………………….……………………. 16
11. TT5 TRIM DETERMINATION …………………….……………………. 21
12. ACCEPTANCE CHECK (PERFORMANCE) …………………….……………………. 26
13. CONTROL SETTING : MAXIMUM NG ADJUSTMENT …………………….……………………. 56
14. CONTROL SETTING : MINIMUM FUEL FLOW CHECK …………………….……………………. 60
15. POST TEST RUN CHECK …………………….……………………. 64
16. UNUSUAL OIL CONDITION …………………….……………………. 66
PT6A series engine testing
INSPEKSI VISUAL DAN CEK KELENGKAPAN
DOKUMEN
START
PREPARASI ENGINE & FASILITAS
QI TC17-002
QI TC17-002 danOVERHAUL MANUAL
CHECK ENGINE & FASILITAS TEST :• CEK KEWAJARAN NILAI ZERO
READING PARAMETER• CEK SISTEM PROTEKSI• CEK FUNGSI KONTROL DYNO
TEST ENGINEQI TC17-002 danOVERHAUL MANUAL
ENGINE TEST PROCESS FLOW CHART
ENGINE & DOKUMEN KOMPLIT
KONTAK PPC
TIDAK
YA
FASILITAS TEST
NORMAL
KONTAK FUNGSI
ETS
TIDAK
YA
EVALUASI HASIL TEST
A
QI TC17-002 danOVERHAUL MANUAL
QI TC17-002 danOVERHAUL MANUAL
3
PT6A series engine testing
BELLMOUTH & EXHAUST CHECK
A
DE-PREPARASI ENGINE
LENGKAPI DOKUMEN TEST
KONTAK PPC
FINISH
QI TC17-002 danOVERHAUL MANUAL
QI TC17-002 danOVERHAUL MANUAL
QI TC17-002 danOVERHAUL MANUAL
ENGINE TEST PROCESS FLOW CHART
4
PT6A series engine testing
TEST REQUIREMENT & PROCEDURE MATRIX
PARAGRAF NO.
PROCEDURE ENGINEGAS
GENERATOR
POWER SECTIO
N
1 General X X X
2 Consumable material X X X
3 Special tools X X X
4 Fixtures, equipment and supplier tools X X X
5 Engine test equipment X X X
7 Symbols X X X
8 Preparation for test X X X
9 Engine motoring, starting & shut down X X X
10A LIMITS X X X
10D Preliminary check X X X
10E AGB vibration survey X X
10G Acceleration and Bodie check X X
10H TT5 trim determination X X
10I Acceptance check / performance check X X
10J Acceptance Value X X
11A Control setting : Minimum Governor check X X
11BControl setting : Propeller Governor maximum speed X X
11CControl setting : Underspeed fuel governing check X X
11D Control setting : Maximum NG adjustment X X
11E Control setting : Minimum Fuel Flow Check X X
12 Post test run check X X
13 Unusual oil condition X
14 Preservation X X
15 Removal of test equipment X X X
18 Final check X X X
19 Power section run – in XNote : The vibration survey requirement applies only to engine being tested following overhaul or repair requiring balancing of the compressor rotor assembly
5
PT6A series engine testing
LIST OF PT6A PARAMETER AND SYMBOL
During static condition / engine not running / zero reading ,the normal reading for parameters are listed below:
SYMBOLSPARAMETER NAME
NORMAL VALUE @ ZERO READING
COMPUTER OHM VALUE UNIT DYNOSP Dyno speed 0 rpmWFPPH Wf Fuel flow 0 pphNGPER Gas generator speed in percent 0 %
NG Ng Gas generator speed in radian per minute 0 rpmNFPER Power turbine speed in percent 0 %
NF Nf Power turbine speed in radian per minute 0 rpmTT11 Engine inlet temperature no 1 70 - 87 deg fTT12 Engine inlet temperature no 2 70 - 87 deg fTT13 Engine inlet temperature no 3 70 - 87 deg fTT14 Engine inlet temperature no 4 70 - 87 deg fTT1A Tt1 Engine inlet temperature average 70 - 87 deg fTT5 Tt5 Interturbine temperature 70 - 87 deg f
TT71 Engine exhaust nozzle temperature no. 1 70 - 87 deg fTT72 Engine exhaust nozzle temperature no. 2 70 - 87 deg fTT73 Engine exhaust nozzle temperature no. 3 70 - 87 deg fTT74 Engine exhaust nozzle temperature no. 4 70 - 87 deg fTT75 Engine exhaust nozzle temperature no. 5 70 - 87 deg fTT76 Engine exhaust nozzle temperature no. 6 70 - 87 deg fTT77 Engine exhaust nozzle temperature no. 7 70 - 87 deg fTT78 Engine exhaust nozzle temperature no. 8 70 - 87 deg f
TT7A Tt7 Engine exhaust nozzle temperature average 70 - 87 deg fTFUEL Tf Fuel temperature 70 - 87 deg fTOILIN Oil temperature 70 - 87 deg fTOILSC Scavenge Oil temperature 70 - 87 deg fPBARO Pam Ambient Barometric Pressure 13.3 - 13.5 psia
PS1 Psn Test cell static pressure same with pbaro psiaPS3 Ps3 Compressure discharge static pressure 0 psig
PGEAR Prgb Reduction Gearbox Static Pressure 0 psigMOP Main Oil Pressure 0 psig
POILSC Scavenge Oil pressure 0 psigTORQ2 Engine Torquemeter Pressure 0 psig
TORQ2S Pam Engine Torquemeter Static Pressure 0 psig
DELP ∂P Delta TORQ2 - TORQ2S TORQ2 - TORQ2S psigVBGEA Gearbox vibration 0 G'sTORQ1 Dyno torque 0 ft lbsTHETA TH THETA 0.92 - 1.053
THETAR RTH Ѵ THETA (AKAR THETA) 1.01 - 1.03DELTA DEL DELTA (PBARO (inHg)/29.921) 0.905 - 0.918
6
PT6A series engine testing
ENGINE MOTORING, STARTING & SHUTDOWN
RUN-IN PROCEDURE
PRELIMINARY CHECK :1. OBTAIN NF/RTH = 33000 RPM2. PERFORM 2 FEATHERING OPERATION3. OIL PRESSURE CHECK
AGB VIBRATION SURVEY
IF ASSUMED THAT ENGINE TREATED AS OVERHAUL AND COMPRESSOR ROTOR HAVEBEEN BALANCING, THEN TEST PROCEDURE SEQUENCE IS:
START
RGB VIBRATION CHECK
ACCELERATION & BODIE CHECK
TT5 TRIM DETERMINATION
A
7
PT6A series engine testing
ACCEPTANCE CHECK / PERFORMANCE
MINIMUM GOVERNOR CHECK
PROPELLER GOVERNOR MAXIMUM SPEED
IF ASSUMED THAT ENGINE TREATED AS OVERHAUL AND COMPRESSOR ROTOR HAVEBEEN BALANCING, THEN TEST PROCEDURE SEQUENCE IS:
UNDERSPEED FUEL GOVERNING CHECK
MAXIMUM NG ADJUSTMENT
MINIMUM FUEL FLOW CHECK
A
POST TEST RUN CHECK
FINISH
PRESERVATION
8
PT6A series engine testing
ENGINE TEST OPERATING CONDITION LIMIT
PARAMETER
MAXIMUM OPERATINGCONDITION
LIMIT
PT6A-21 PT6A-27/28 PT6A-25
NG (rpm)Steady State
38,100 (101.7%)
38,100 (101.7%)
38,100 (101.7%)
Acceleration38,500
(102.75%)38,500
(102.75%)38,500
(102.75%)
NF (rpm)Steady State
34,200 (103.6%)
34,200 (102.9%)
34,200 (103.6%)
Acceleration*36,300 (110%)
36300 (109.2%)
36,300 (110%)
TT5 (deg F)
Start 1350 1440 1350
Steady State (trimmed) 1283 1380 1283
Steady State (untrimmed) 1325 1400 1325
delP (inHg)Steady State 92 125 94
Acceleration* 94 127 94
NOTE : Rundown time on the compressor from ground-idle must not be < 20 seconds
*2 second time limit
SUPPLEMENTARY LIMITATION
PARAMETER LIMIT
Fuel pressure @ engine inlet all time including transient 5 - 20 psig
Oil temperature for all running except transient 140 - 160 deg F
Scavenge oil b ack pressure @ engine outlet 20 - 50 psigMaximum permitted difference between individual inlet temp. indication 8:F
Maximum permitted difference between average Tt7 thermocouple reading between each exhaust nozzle assembly 60:F
Maximum permitted difference between thermocouple within a given nozzle 100:F
Maximum operating vibration limit 100 G's
Maximum acceptance vibration limit 70 G's
9
PT6A series engine testing
ENGINE MOTORING, STARTING & SHUT DOWN
WET MOTORING RUN
IF FIRE CONDITIONS OCCURS WITHIN ENGINE DURING MOTORING RUN , IMMEDIATELY CLOSE FUEL SHUTOFF VALVE
AND CONTINUE MOTORING ENGINE
ALLOW SUFFICIENT STARTER COOLING PERIOD BETWEENMOTORING CYCLES AND ENGINE START; REFER TO STARTERMANUFACTURERS LIMITS AND RECOMMENDATIONS.
DRY MOTORING RUN
This procedure is used to remove internally trapped fuel and fuel vapor, or ifthere is evidence of fire within the engine. Air passing through the engineserves to purge fuel/fuel vapor from the combustion section, power turbine andexhaust system.
ENGINE STARTING
ALLOW SUFFICIENT STARTER COOLING PERIOD BETWEENMOTORING CYCLES AND ENGINE START; REFER TO STARTERMANUFACTURERS LIMITS AND RECOMMENDATIONS.
THE ENGINE MUST START AND REACH IDLE WITHIN 35 SECONDS OF INITIATION OF THE START. THE FIRST START OF THE DAY CAN SOMETIMES TAKE LONGER; THEREFORE, THE START TIME MUST BE CORRECTED TO COMPENSATE FOR LONG TIME TO LIGHT. FOR TTL GREATER THAN 3 SECONDS: TTI MODIFIED = TTI RECORDED - (TTL – 3 SECONDS). IF THIS REQUIREMENT IS NOT ACHIEVED, check the FCU pneumatic system for leaks. If no leaks are found, replace the FCU.
IF Tt5 OBSERVED EXCEEDS 1440°F OR CONTINUOUS FLAME ISSUESFROM EXHAUST, SHUT OFF START CONTROL LEVER IMMEDIATELY.DO NOT ATTEMPT TO RELIGHT ON RUNDOWN; WAIT UNTIL THEENGINE COMES TO REST, THEN IMPLEMENT A DRY MOTORING CYCLETO COOL THE ENGINE
10
PT6A series engine testing
ENGINE MOTORING, STARTING & SHUT DOWN
SHUT DOWN
IF A FIRE OCCURS IN THE ENGINE AFTER SHUTDOWN, DO A DRYMOTORING RUN IMMEDIATELY
For normal shut down, allow engine to run at ground idle for at least one minute to stabilize at minimum running temperatures.
11
PT6A series engine testing
RUN-IN PROCEDURE
NOTE : This procedure is to be done after scheduled or unscheduled overhaul/repair has been completed.
1) Do a wet motoring run followed with a dry motoring run.
2) Start the engine and run at ground-idle 19750 ± 500 rpm Ng (propeller testing) or rotate dynamometer controller to obtain 5000 rpm Nf or maximum available (dynamometer testing) for 5 minutes.
3) Record Ng, Nf, Tt1, Tt5, del P, oil pressures and oil temperatures.
12
PT6A series engine testing
AGB VIBRATION SURVEY
NOTE: 1. The vibration survey requirement applies only to engines being tested following overhaul or repair requiring balancing of the compressor rotor assembly.
1) Select ‘‘Acceleration Survey’’ from the menu on the analyzer.
2) Set power control lever to GROUND-IDLE.
3) Set propeller control lever to 33000 rpm Nf.
NOTE: 2. Do the vibration survey using the following procedures and the ACES Operator’s Manual. Personnel must be familiar with the Analyzer prior to performing these operations.
CAUTION: DO NOT EXCEED ENGINE OPERATING LIMITS. ENGINEOPERATING LIMITS SUPERSEDE ANY INSTRUCTION IN ACESANALYZER PROCEDURE.
ACCELERATION SURVEY
4) Ng Sweep:
a) Press ‘‘Enter’’ on the analyzer to start recording.
b) Accelerate slowly at a rate of 5000 rpm/min from GROUND-IDLE to max available Ng without exceeding any operating limits. Reduce to GROUND-IDLE.
c) Press ‘‘Enter’’ on the analyzer to stop recording.
13
PT6A series engine testing
AGB VIBRATION SURVEY
1) Select ‘‘shutdown Survey’’ from the menu on the analyzer.
2) Press ‘‘Enter’’ on the ACES Analyzer to start recording. Shut down engine from idle.
SHUTDOWN SURVEY
3) End vibration survey after engine reaches 0 rpm and a sync error appears on the ACES Analyzer; then press ‘‘Enter’’ on the ACES Analyzer to stop recording.
1ENg VIBRATION ACCEPTANCE LIMIT
a. From the plots produced above, ensure that 1ENg vibration level does not exceed the following limits:GROUND-IDLE to max Ng ; 0.5 cm/secShutdown from GROUND-IDLE to 5000 rpm Ng; 0.5 cm/sec
14
PT6A series engine testing
RGB VIBRATION CHECK
1) Set Nf to 33000 +100/-0 rpm.
2) Carry out a slow acceleration (4,000 rpm/min.) from ground idle to maximum attainable Ng, do not exceed any operating limit.
NG SWEEP
3) Carry out a slow deceleration (4,000 rpm/min.) from maximum attainable Ng to ground idle.
4) Record Ng, Nf, torque and vibrations at the highest vibration peak from steps (2) and (3).
NF SWEEP
1) Set Nf to 33000 +100/-0 rpm.
2) Increase power to a torque of 80 ± 3 in. Hg
3) Carry out a slow deceleration (4,000 rpm/min.) from 33000 +100/-0 rpm to 24,500 rpm. Engine torque must be kept at 80 ± 3 in. Hg during deceleration.
4) Carry out a slow acceleration (4,000 rpm/min.) from 24,500 rpm to 33000 +100/-0 rpm. Engine torque must be kept at 80 ± 3 in. Hg during acceleration.
5) Record Ng, Nf, torque and vibrations at the highest vibration peak from steps(3) and (4).
15
PT6A series engine testing
ACCELERATION & BODIE CHECK
1) If engine response is sluggish, or acceleration rate is too slow, check P3 and fuel system pneumatic control tubes and connectors for leakage or obstruction, before any fuel control adjustments are made
2) Position power control lever maximum stop on console to limit torque to 86.3 in.Hg.(PT6A-21 engines) or 108.6 in.Hg. (PT6A-27/-28 engines) or maximum obtainable without exceeding engine operating limits. Lock stop on console.
3) Rotate dynamometer controller to give 32000 rpm Nf (97% for PT6A-25, 96% for PT6A-27/28).
4) Record Ng, Nf, Tt1 and δP.
5) Decrease power control lever to flight-idle 23600 ± 100 rpm Ng.
6) Slam accelerate from flight-idle to T.O. timed to 97.5% of take-off Ng. Slam decelerate to ground-idle (19750 ± 500).
NOTE: The time taken to move power control lever in checks (5) through (6) must not exceed 1.0 second, engine should respond smoothly during acceleration and deceleration.
ACCELERATION CHECK
16
PT6A series engine testing
ACCELERATION & BODIE CHECK
7) Acceleration time must fall within range specified
NOTE: The time taken to move power control lever in checks (5) through (6) must not exceed 1.0 second, engine should respond smoothly during acceleration and deceleration.
8) If necessary, adjust engine acceleration by rotating FCU acceleration dome one detent at a time, using minimum number to obtain satisfactory acceleration. Rotate dome clockwise to decrease (faster acceleration) and counterclockwise to increase (slower acceleration) acceleration time.
CAUTION: MAXIMUM ADJUSTMENT ON FCU ACCELERATION DOME TO MEET ACCELERATION TIME IS THREE CLICKS CLOCKWISE ORCOUNTERCLOCKWISE.
17
PT6A series engine testing
ACCELERATION & BODIE CHECK
9) For example, the inlet screen temp. (TT1) during the day is 80: F, then the acceleration time limits are :low limit = 2.42 + 0.35 = 2.77 secondshi limit = 3.44 + 0.35 = 3.79 seconds
18
PT6A series engine testing
ACCELERATION & BODIE CHECK
1) Rotate FCU acceleration dome three detents clockwise to increase fuel flow.
2) Run engine for not less than one minute at maximum stop without exceeding operation limit (Ref. step (2) preceding) to achieve stabilization.
BODIE CHECK
3) Slam decelerate to 32000 Ng (85%), then without dwelling at lower speed, slam accelerate to maximum stop. Repeat to 26000 Ng (70%); again slam to maximum stop. Reduce Ng to GI.
4) If engine is stall and surge free on completion of bodie checks, reset acceleration dome to original position (three detents counterclockwise).
5) If engine stall or surge is experienced during checks, rotate acceleration dome one detent counterclockwise and repeat bodiecheck.
6) If surge is still evident, check compressor bleed valve operation..
7) If bleed valve is functioning correctly, the dome may be reset a further twodetents, a bodie check being implemented after each detent adjustment..
19
PT6A series engine testing
ACCELERATION & BODIE CHECK
8) When surge is eliminated, reset dome three detents counter clockwise from surge-free setting.
9) After satisfactory completion of bodie check following adjustment, recheck acceleration time (Ref. steps (5) and (6) ACCELERATION CHECK preceding).
BODIE CHECK continued
10) Following acceptable acceleration and bodie checks, if scribe marks do not align, remove seal and lockwire on FCU acceleration dome. Holding adjusting screw with an Allen wrench, loosen adjuster locknut. Turn dome to re-align scribe marks, then tighten locknut, lockwire and seal. lockwire dome tab.
20
PT6A series engine testing
TT5 TRIM DETERMINATION
1) Start engine, and advance power control and propeller control levers (propeller testing) or rotate dynamometer controller until engine is operating at observed power of 550 ± 10 SHPCEG (PT6A-21 engines) or 680 ± 10 SHPCEG (PT6A-27/-28 engines) or maximum power obtainable without exceeding engine operating limits and at an NFC equal to 33000 rpm but not to exceed 34200 rpm (NF observed).
2) Run engine for 5 minutes at this power setting to obtain stabilization. Annotate log sheet; Tt5 Trim Determination and record set of readings.Nf, Ng, Pam or Baro, Psn or P1000, Ps3, Δp, SG, Tf, Tsg, Tt1, Tt5, Tt7
3) Determine trim value from readings in step (2), preceding. Process Data with Program PWC83020.
4) With results obtained in step (3) preceding, calculate trim to suppress TT5/TH to a value T5D/TH - 60° ± 10 F° (PT6A-21/-27/-28 engines) or T5D/TH - 65° ± 5 F° (PT6A-28 Piper engines only).Tt5 Trim Determination (example):TT5/TH = 1753°RT5D/TH = 1733°RT5D/TH - 60° = 1733 - 60 = 1673°Rdel T5/TH trim = 1753 – 1673 = 80°
5) Trim value obtained in step (a) preceding is for a 59°F day. To trim engine, this value should be denormalized as follows:
del T5/TH x TH = del T5.
21
PT6A series engine testing
TT5 TRIM DETERMINATION continued
6) Select appropriate class of trim harness (P/N 3013604 or P/N 3031417) (Ref. Table703).
7) Install selected trim harness (Ref. Final Assembly), and record class in log sheet.
8) Start engine and run at take-off power (Ref. step (1), preceding).
9) After allowing for stabilization of readings, make sure that selected trim reduces Tt5 by the required value. If you are using program PWC83020, check the T5 trim check box and the output screen will state if the trim is good or not. Should it be necessary, install another class of trim and recheck.
22
PT6A series engine testing
TT5 TRIM DETERMINATION continued
TABLE 703, Trim Harness Classification
3031417 ± 5% @ 70°F Approx. Ohms Approx. Range F° 3013604
Class 10 3.75 to 3.95 -208 to -200 -
Class 11 3.95 to 4.20 -200 to -190 -
Class 12 4.20 to 4.45 -190 to -180 -
Class 13 4.45 to 4.75 -180 to -171 -
Class 14 4.75 to 5.10 -171 to -161 -
Class 15 5.10 to 5.50 -161 to -151 -
Class 16 5.50 to 5.90 -151 to -142 -
Class 17 5.90 to 6.40 -142 to -132 -
Class 18 6.40 to 6.90 -132 to -123 -
Class 19 6.90 to 7.66 -123 to -114 -
Class 20 8 -114 to -104 -
Class 25 9 -104 to - 91 Class 1
Class 30 10.5 - 91 to - 80 Class 2
Class 35 12 - 80 to - 71 Class 3
Class 40 14 - 71 to - 61 Class 5
Class 45 16 - 61 to - 51 Class 7
Class 50 19 - 48 to - 45 Class 10
Class 55 24 - 40 to - 35 Class 20
Class 60 30 - 34 to - 28 Class 30
Class 65 43 - 25 to - 20 Class 40
Class 70 72 - 15 to - 10 Class 50
Class 75 110 - 9 to - 6 Class 60
23
PT6A series engine testing
TT5 TRIM DETERMINATION continued
FLOW CHART OF TT5 TRIM DETERMINATION
1. Run engine to maximum power obtainable, NFC =
33000 rpm, don't exceed operating limit.
2. Stabilize for 5 minutes.
3. Take fullset reading
START
TSG, SG, LHV, Ng, Nf, Pbaro,
Psn, P3, Tt5, Torq1, delP,
Wf,Tfuel, Tt1, Tt7
Input to and process
with Program Drp
PWC83020
TT5TH AND T5DTHNOTE :
TH = (Tt1+459.688)/518.688
delT5TH = TT5TH - (T5DTH - 60)
delT5 = delT5TH x TH
delT5
LOOKUP TABLE 703
TRIM
CLASS
install trim harness
1. Run engine to TAKEOFF or maximum power
obtainable, NFC = 33000 rpm, don't exceed
operating limit.
2. Make sure that selected trim reduces Tt5 by the
required value.
SELESAI
example :
TH = 1.05,
TT5TH = 1753 R,
T5DTH = 1733 R,
delT5TH = 1753 - (1733 - 60) = 80,
delT5 = 80 x 1.05 = 84,
lookup table 703, p/n : 3031417
trim class = class 30, -91 to -80
24
PT6A series engine testing
TT5 TRIM DETERMINATION continued
EXAMPLE OF TT5 TRIM DETERMINATION
The data from left column above, taken from fullset @ takeoff. The data will process with DRP program PWC83020.
The output from program are :THETA = (ENGINE INLET TEMP + 459.688)/518.688
= (85.93 + 459.688)/518.688 = 1.05T5D/THETA = 1723.8 deg RCORR.TT5 (TT5/THETA) = 1752.4 deg R
With refer to flow chart, then :(T5D/THETA ) - 60 = 1723.8 – 60 = 1663.8DELTA TT5/ THETA TRIM = CORR.TT5 (TT5/THETA) – (T5D/THETA) – 60
= 1752.4 – 1663.8 = 88.6DELTA TT5 DENORMALIZE = DELTA TT5/ THETA TRIM X THETA
= 88.6 X 1.05 = 93.03 = 93LOOKUP TO TABLE 703 → 93 → CLASS 25 OR CLASS 30
25
PT6A series engine testing
ACCEPTANCE CHECK (PERFORMANCE)
Before we move deeply to Acceptance Check, better if we have a goodunderstanding on several important parameter which were used fordetermine the result of acceptance check .
The parameter which mentioned above are SHPCEG, NGC, WFC, SFC andTT5C.
26
PT6A series engine testing
ACCEPTANCE CHECK (PERFORMANCE)
SHPCEG BLOCK DIAGRAM
TT5
(interturbine temp)deg FTT5 DEG R
(tt5 + 459.688)
TT5C or TT5TH
(TT5 DEG R / THETA )
TT1 AVG
(engine inlet temp)deg F
THETA
(tt1 avg + 459.688 / 518.688)
TT5C or TT5TH BLOCK DIAGRAM
TORQ3
(static torq press) psig
TORQ2
(torqmeter press)psig
NF
(power turbine speed)rpm
KONSTAN
PT6A-27 = 5272
PT6A-25 = 5183
PBAR
(ambient press)
standard press
(14.696 psi)
TT1 avg
(engine inlet temp)deg F
del P
(torq2 - torq3 x 2.036)
SHP
(del P x NF / KONSTAN)
psia
DELTA
(pbar / standard press)
THETA
(tt1 avg + 459.688) / 518.688
sq root THETA
(theta ̂0.5)
SHPCEG
(SHP / DELTA / sqroot THETA)
27
PT6A series engine testing
ACCEPTANCE CHECK (PERFORMANCE)
WFC BLOCK DIAGRAM
SFCC BLOCK DIAGRAM
FTSAMP
(fuel sample temp) deg F
SPGRAV
(fuel spec. gravity) psig
WFGPM
(fuel flow)gpm
PBAR
(ambient press)
standard press
(14.696 psi)
TT1 avg
(engine inlet temp)deg F
CORR SPGRAV
(spgrav-1.2875)/(ftsamp+1164)x(tfuel-ftsamf)+spgrav
psia
DELTA
(pbar / standard press)
THETA
(tt1 avg + 459.688) / 518.688
sq root THETA
(theta ̂0.5)
WFC
(wfpph / DELTA x sqroot THETA)
TFUEL
(fuel temp)deg F
WFPPH
(wfgpm x 499.68 x corr spgrav)
SHPCEG
(corr shp engine)
WFC
(corr WF)
hp
SFCC
(shpceg / wfc)
pph
28
PT6A series engine testing
ACCEPTANCE CHECK (PERFORMANCE)
NGC BLOCK DIAGRAM
TT7C BLOCK DIAGRAM
TT1 avg
(engine inlet temp)deg FTHETA
(tt1 avg + 459.688) / 518.688
sq root THETA
(theta ̂0.5)
NGC
(ng / sqroot THETA)
NG
(gas producer speed)rpm
TT1 avg
(engine inlet temp)deg FTHETA
(tt1 avg + 459.688) / 518.688
TT7AC
(TT7A DEG R / THETA)
TT7 AVG
(engine exhaust nozzle temp)deg F
TT7A DEG R
(tt7 avg + 459.688)
PBAR
(ambient press)
standard press
(14.696 psi)
PS3
(compressor discharge press)psig
psia
DELTA
(pbar / standard press)
PS3C
(PS3 / DELTA )
PS3C BLOCK DIAGRAM
29
PT6A series engine testing
ACCEPTANCE CHECK (PERFORMANCE)
PROCEDURE
CAUTION : DO NOT EXCEED ENGINE OPERATING LIMITS
1) Run to following powers at Nf/RTH equal to 33000 rpm, but not to exceed 34200 rpm (observed).
2) Record readings for each of the power setting points :
3) PT6A-21 or PT6A -25 engines: :
a) 550 SHP/DELRTH or maximum power obtainable.
a) 495 SHP/DELRTH.
4) PT6A-27/28 engines: :
a) 680 SHP/DELRTH or maximum power obtainable.
a) 620 SHP/DELRTH.
5) From readings obtained in steps (3) or (4) preceding, process data with program PWC83020. Plot the best straight line across the normalized values of Wf, Tt5 and Ng against shp on engine performance graph. (Ref. Fig. 711).
30
PT6A series engine testing
ACCEPTANCE CHECK (PERFORMANCE)
ACCEPTANCE VALUE
1) Enter curve at 550 shp (PT6A-21 engines) or 680 shp (PT6A-27/-28 engines) and record corresponding values for SFC, Tt5 and Ng for take-off power in corrected engine performance block.
2) Check parameters determined in step (1) against required parameters (Ref. Table 704).
32
PT6A series engine testing
ACCEPTANCE CHECK (PERFORMANCE)
ACCEPTANCE CHECK – performance calculation example
42