quickrwall - guía de usuario
TRANSCRIPT
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 1/51
QuickRWall
User’s Guide
Retaining Wall Design Software
Version 3.0
Copyright (c) 2003-12 Ensoltech, Inc. All rights reserved.
QuickRWall is a proprietary computer program of Ensoltech, Inc. Although every effort has been made to
ensure the accuracy of this program and its documentation, neither Ensoltech nor Integrated Engineering
Software shall be held liable for any mistake, error, or misrepresentation in, or as a result of the usage of,
this program and/or its documentation. The results obtained from this program should not be substituted
for sound engineering judgment.
SALES /SUPPORT
Integrated Engineering Software
519 E. Babcock St.
Bozeman, MT 59715
406-586-8988 (sales)
www.iesweb.com
1
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 2/51
QuickRWall 3.0 User’s Guide CONTENTS
Contents
1 Overview 51.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.6 Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.7 Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Menu Commands 82.1 File Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1.1 New . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1.2 Open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1.3 Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.4 Save As... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.5 Print Report... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.6 Print Full Page Drawing... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.7 Preview Report... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.8 Preview Full Page Drawing... . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.9 Print Setup... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.10 Create DXF File... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.11 [Recent Files] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.12 Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2 View Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2.1 Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2.2 Status Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3 Project Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3.1 Add Load Case... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3.2 Remove Load Case... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3.3 Project Information... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3.4 Set Defaults... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112.3.5 Stored Walls... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4 Design Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4.1 Choose Footing Reinforcement . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4.2 Choose Stem Reinforcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4.3 Position Key To Embed Stem Bars . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4.4 Set All Embedment Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4.5 Set All Lap Splice Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4.6 Set Bar Cutoff Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 3/51
QuickRWall 3.0 User’s Guide CONTENTS
2.4.7 Design Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.5 Options Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.5.1 Units... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5.2 Preferences... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5.3 Concrete Load Combinations... . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5.4 Masonry Load Combinations... . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5.5 Stability Load Combinations... . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.6 Help Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.6.1 Help Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.6.2 Update QuickRWall 2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.6.3 FAQ Answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.6.4 Technical Support Information... . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.6.5 Email ’[email protected]’... . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.6.6 Software License... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.6.7 About QuickRWall 2.0... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3 User Inputs 153.1 Criteria Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.1.1 Design Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.1.2 Assumptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.1.3 Stability Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.1.4 Geotechnical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2 Load Case Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.2 Backfill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.3 Water in Backfill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2.4 Passive Pressure @ Toe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2.5 Surcharge (Uniform) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2.6 Surcharge (Line/Strip) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233.2.7 Uniform Lateral Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.2.8 Stem Axial Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.2.9 Seismic Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.3 Wall (Footing/Stem) Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.3.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.3.2 Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.3.3 Footing Geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.3.4 Heel Reinforcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.3.5 Toe Reinforcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.3.6 Transverse Reinf. (S&T) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.3.7 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.3.8 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.3.9 Geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323.3.10 Reinforcement (Flexural) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.3.11 Reinforcement (S&T) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.3.12 Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.4 Stem Section Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.4.2 Masonry Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.4.3 Reinforcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 4/51
QuickRWall 3.0 User’s Guide CONTENTS
4 Forces on the Wall 384.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.1.1 Forces Used for Stem Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.1.2 Multiple Load Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.2 Backfill Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.3 Water Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.4 Passive Pressure @ Toe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.5 Uniform Surcharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.6 Line/Strip Surcharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.7 Seismic Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.8 Wall Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.9 Soil Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.10 Bearing Reaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.11 Friction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5 Checks 425.1 Stability Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.1.1 General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.1.2 Checks Performed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.2 Stem Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
5.2.1 General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
5.2.2 Checks Performed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.3 Toe Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
5.3.1 General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
5.3.2 Checks Performed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
5.4 Heel Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.4.1 General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.4.2 Checks Performed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 5/51
Chapter 1
Overview
1.1 Introduction
Thank you for choosing QuickRWall. This software package has been created to assist the engineer in the
design of retaining walls. Use of this program can save countless hours in the calculations and documenta-
tion associated with retaining wall design. The software has been designed so that you may quickly become
productive with very little training, but by reading through this manual and other associated documentation
you should be able to resolve any questions that may arise during program use.
1.2 License
Use of this software program is strictly governed by the license agreement that is displayed during the install
process. This program is the copyrighted property of Ensoltech, Inc. and is provided for the exclusive use of
each licensee. Additional licenses may be obtained exclusively through Integrated Engineering Software.
You may copy the program for backup purposes and you may install it on any computer allowed in the
license agreement. Distributing the program to coworkers, friends, or duplicating it for other distribution
violates the copyright laws of the United States. Future enhancements and technical support for this product
depend on your cooperation in this regard.
1.3 Disclaimer
With any technical software package, there will be concerns about possible errors. We have worked very
hard to ensure that this software is as accurate and robust as possible.
Despite our best efforts, errors in software can and do occur. It is very important to manually inspect the
results and ensure that they are consistent with sound engineering practice and judgement. This program
has been designed with that end in mind, exposing calculations wherever possible so they are available
for examination. It is the responsibility of the engineer to ensure the final design produced is reasonable
and constitutes sound engineering practice. In no event shall Integrated Engineering Software, Inc. or
Ensoltech, Inc. be liable for any direct or indirect damages resulting from the use of this software or its
related documentation.
5
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 6/51
QuickRWall 3.0 User’s Guide CHAPTER 1. OVERVIEW
1.4 Requirements
The software has relatively minimal system and hardware requirements:
• Windows XP/Vista/7
• 20 MB of hard disk space
• 512 MB of RAM
• 1024x768 screen resolution
1.5 Installation
To install, simply run the install program that comes on the CD or that you have downloaded from the IES
website. The step-by-step wizard will guide you through the installation process.
1.6 Technical Support
Before you contact IES for support, please make sure you have taken full advantage of the readily available
resources that are included with the software:
• Carefully read through this users guide
• Refer to the numerous help screens built into the software
• If you have a question about a result displayed in a summary, be sure to check the full calculations
that are displayed in the program and in the report.
• Check the resources on the IES website. These can be accessed easily by going to the Help menu and
choosing Technical Support Information.You should also make sure that you have the latest maintenance update for the software. These updates are
free and can be obtained automatically by going to the Help menu, then choosing Update QuickRWall. In
this manner you can make sure that the issue you have a question about has not already been resolved.
Integrated Engineering Software provides technical support for this program via email. The best way to
send an email is to go to the Help menu, then choose Email IES Technical Support.
1.7 Limitations
Following are situations that the program does not address in its current release. Please let us know if any
of the items on this list (or not on this list) are of critical importance to you. Customer feedback is the #1
criteria in determining which features are added to future versions.
• Segmental / MSE walls
• Multi-level basement walls (multiple lateral supports)
• Soldier pile walls
• Rock anchors
• Walls without footings
• Walls on pile foundations
• Counterfort walls
6
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 7/51
QuickRWall 3.0 User’s Guide CHAPTER 1. OVERVIEW
• Buttress walls
• Strength design of masonry walls (currently only ASD)
• Sheet pile walls
• Multiple soil layers (other than a saturated layer beneath the water table)
• Water above the backfill surface
• Support bilinear backfill slope (e.g. levels off)
• Perform strength checks on the key beneath the footing
7
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 8/51
Chapter 2
Menu Commands
2.1 File Menu
These are the commands available on the File Menu.
2.1.1 New
Creates a new file without any projects.
2.1.2 Open
Opens an existing project file.
8
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 9/51
QuickRWall 3.0 User’s Guide CHAPTER 2. MENU COMMANDS
2.1.3 Save
Saves the current project file. If the file has not been previously saved and does not yet have a file name, a
dialog will prompt for the file name.
2.1.4 Save As...
Saves the current project file, always prompting for a file name.
2.1.5 Print Report...
Prints a report containing a summary and/or details of the design calculations. A dialog appears first to
allow you to specify which items are to be included in the report.
2.1.6 Print Full Page Drawing...
Prints a full page drawing of the wall.
2.1.7 Preview Report...
Previews a report containing a summary and/or details of the design calculations. A dialog appears first to
allow you to specify which items are to be included in the report.
2.1.8 Preview Full Page Drawing...
Displays a preview of a full page drawing of the wall.
2.1.9 Print Setup...
Selects a printer and printer connection. Also allows you to choose portrait or landscape page orientation.
This option is there because this is a standard dialog from Microsoft, but you should not select the landscape
option. The report pages are not designed for it and will look funny.
2.1.10 Create DXF File...
Creates a DXF file that contains a fully dimensioned drawing of the wall. A dialog box will appear to allowyou to specify the name and location of the file.
2.1.11 [Recent Files]
Opens the recently used project file with the displayed name.
9
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 10/51
QuickRWall 3.0 User’s Guide CHAPTER 2. MENU COMMANDS
2.1.12 Exit
Exits the program.
2.2 View Menu
These are the commands available on the View Menu.
2.2.1 Toolbar
Shows/hides the toolbar.
2.2.2 Status Bar
Shows/hides the status bar.
2.3 Project Menu
These are the commands available on the Project Menu.
2.3.1 Add Load Case...
Adds an additional load case to the project. Note that multiple load cases in this program are simply a way
of applying a different set of unrelated, non-combinable loads. There is no support for combining different
cases with various factors etc.; only loads within a single load case will be combined and factored. The
multiple load case feature simply offers a way to consider different loading scenarios. Most projects willnot require more than one load case.
2.3.2 Remove Load Case...
Brings up a dialog that allows you to remove a load case. You can only use this command when there is
more than one load case, since it is required that there be at least one load case at all times.
10
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 11/51
QuickRWall 3.0 User’s Guide CHAPTER 2. MENU COMMANDS
2.3.3 Project Information...
Brings up a dialog that allows you to enter information for this specific project. This information is dis-
played in the header area of reports.
2.3.4 Set Defaults...
This command allows you to indicate that the current inputs are to be recorded as the default settings for
future projects. A dialog will appear to allow you to specify which groups of inputs are to be saved.
2.3.5 Stored Walls...
This allows access to previously created and stored walls.
2.4 Design Menu
These are the commands available on the Design Menu.
2.4.1 Choose Footing Reinforcement
This command will choose reinforcement for both the heel and the toe. It is best used after the width and
thickness of the footing have already been set. The bars chosen will be governed by the current design
preferences (see the Design Preferences command).
2.4.2 Choose Stem Reinforcement
This command will choose reinforcement for the stem. It is best used after the stem thickness has already
been set. Currently this command only does basic sizing of bars at the base of the stem and does not dealwith some of the more complicated scenarios, in particular the specification of bars for a multi-piece stem,
restrained stem, or masonry stem. We are planning to improve this command considerably in a future
version (please let us know if this is important to you). The bars chosen will be governed by the current
design preferences (see the Design Preferences command).
11
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 12/51
QuickRWall 3.0 User’s Guide CHAPTER 2. MENU COMMANDS
2.4.3 Position Key To Embed Stem Bars
Creates a key (if there isn’t one already there) and positions it such that it provides development for the
stem reinforcement, if it extends below the footing. The key is also positioned such that the bars can act as
reinforcement for the key in case it is required (although the program does not perform calculations to test
the adequacy of key reinforcement).
2.4.4 Set All Embedment Lengths
Calculates the required embedment lengths for the stem, heel, and toe bars, and lengthens the bars if they are
too short. Note that in the case where the stem bars are hooked into the footing, this may cause the footing to
be thickened in order to achieve the necessary development length for the hook (Ldh). Otherwise, the stem
bars are allowed to stick out of the bottom of the footing, and it is left as a separate step for the engineer to
either position a key to contain them (recommend the ’Position Key to Embed Stem Bars’ command above)
or to hook them into the footing.
2.4.5 Set All Lap Splice Lengths
Calculates the required lap length for all lap spliced bars and extends the lap length if required. Note that
in some situations where there are no lapped bars, but potentially could be, the program will prompt you
asking whether to lap the bars, and then set the proper length.
2.4.6 Set Bar Cutoff Lengths
Ensures that all bar cutoffs occur a sufficient distance past the point where the bars are required for flexure,
and that cutoffs in a tension zone meet the applicable ACI requirements. Lengthens the cutoff bars if
necessary. Note that in some situations where there are no cutoff bars, but potentially could be, the program
will prompt you asking whether to cut off alternate bars, and then set them to the proper length.
2.4.7 Design Preferences
This brings up a dialog that lets you specify some settings such as available bars sizes and preferred bar
spacings. This helps to make the automatic design results as practical as possible.
2.5 Options Menu
These are the commands available on the Options Menu.
12
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 13/51
QuickRWall 3.0 User’s Guide CHAPTER 2. MENU COMMANDS
2.5.1 Units...
Brings up a dialog allowing to modify the units used for various different quantities.
2.5.2 Preferences...
Brings up a dialog that allows use control of various aspects of program behavior.
2.5.3 Concrete Load Combinations...
Brings up a dialog allowing you to add, modify, or remove load combinations or groups of load combina-
tions used for concrete design. This is the command that allows adding custom load factors/combinations.
Note that you should not change the factors for the built-in, code-defined load combinations. The program
will load its own built-in values for these at startup every time and overwrite your changes. If you would
like to have a modified copy of one of these built-in combination sets, change its name (e.g. change ’IBC2003’ to ’IBC 2003 (a)’). In this example, the program will load up a ’fresh’ copy of ’IBC 2003’ at startup
and also leave your modified version (’IBC 2003 (a)’).
2.5.4 Masonry Load Combinations...
Brings up a dialog allowing you to add, modify, or remove load combinations or groups of load combina-
tions used for masonry design. You should avoid modifying the built-in combinations; see the ’Concrete
Load Combinations’ topic for guidelines regarding this issue.
2.5.5 Stability Load Combinations...
Brings up a dialog allowing you to add, modify, or remove load combinations used for stability checks
(sliding & overturning). You should avoid modifying the built-in combination(s); see the ’Concrete Load
Combinations’ topic for guidelines regarding this issue.
2.6 Help Menu
These are the commands available on the Help Menu.
13
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 14/51
QuickRWall 3.0 User’s Guide CHAPTER 2. MENU COMMANDS
2.6.1 Help Contents
Brings up the help dialog, which presents a tree-style display of the available help topics.
2.6.2 Update QuickRWall 2.0
Initiates the process of checking for an update and, if necessary, automatically updates the program from
the IES website. Note that you must be connected to the Internet for this feature to work properly.
2.6.3 FAQ Answers
Opens a web browser window with the IES Frequently Asked Questions (FAQ) web page.
2.6.4 Technical Support Information...
Opens a web browser window with the Technical Support Information web page. This location provides
access to several problem-solving resources.
2.6.5 Email ’[email protected]’...
Creates a new email message, addressed to IES tech support, and attaches certain useful system information
that helps IES diagnose the source of potential problems. This is the best way to contact IES regarding
technical support issues.
2.6.6 Software License...
Brings up a dialog where current license information can be viewed, or new license information can be
entered.
2.6.7 About QuickRWall 2.0...
Displays a dialog with version number, copyright, and other related information.
14
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 15/51
Chapter 3
User Inputs
3.1 Criteria Inputs
3.1.1 Design Code
These are definitions of the inputs in the ’Design Code’ group.
15
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 16/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Building Code
The governing building code for code checks.
Use ASD for Masonry Design
This option causes masonry checks to be performed using ASD provisions, rather than strength design
provisions.
Concrete Load Combs
The source of the load combinations that will be considered when performing checks on the concrete com-
ponents of the wall. The abbrevation ’Str’ indicates ’Strength’ (combinations for strength as opposed to
allowable stress design).
Masonry Load Combs
The source of the load combinations that will be considered when performing checks on a masonry stem.
If the stem is constructed entirely of concrete this setting has no effect. The abbrevation ’ASD’ indicates
’Allowable Stress Design’ (as opposed to strength design combinations).
Stability Load Comb
The source of the load combinations that will be considered when performing stability checks on the wall.
3.1.2 Assumptions
These are definitions of the inputs in the ’Assumptions’ group.
Restrained Against Sliding
Check this option if there is an external restraint, such as a slab, that prevents the wall from sliding. This
will cause the program to skip the sliding stability check.
Neglect Bearing At Heel
This causes the bearing pressure beneath the heel to be ignored when computing the critical moment and
shear for the heel check. Checking this is conservative, but can sometimes lead to unrealistically high design
forces.
Use Vert. Comp. for OT
Causes the vertical component of the backfill force to be included in the overturning check. This force helps
to resist overturning.
16
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 17/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Use Vert. Comp. for Sliding
Causes the vertical component of the backfill force to be included in the sliding check. The contribution
shows up indirectly via an increased friction force. This force helps to resist sliding.
Use Vert. Comp. for Bearing
Causes the vertical component of the backfill force to be included in the bearing pressure calculation. This
will increase the total bearing reaction, but can decrease the maximum pressure by evening out the pressure
distribution.
Use Surcharge for Sliding & OT
Causes the applied surcharge over the backfill to help resist sliding and overturning.
Use Surcharge for Bearing
Causes the applied surcharge over the backfill to contribute to the bearing pressure. This will increase
the average bearing pressure, but can sometimes decrease the maximum value by evening out the overall
distribution. Note that this will also affect the toe and (possibly) heel design, since the bearing pressure
influences the design shear and moment for those components.
Neglect Soil Over Toe
Causes the weight of the soil over the toe to be neglected for strength design of the toe. This setting does
not affect stability checks.
Neglect Backfill Wt. for Coulomb
Causes the weight of the backfill to be neglected when the Coulomb earth pressure theory is used. This
option is provided to be consistent with the recommendations of some textbooks, but is not appropriate in
many situations and should be used with caution.
Factor Soil Weight As Dead
Causes soil weight to be given the dead load factor rather than the earth load factor.
Use Passive Force for OT
Causes the resultant force force from passive pressure (if there is one) to be excluded from the overturning
check. This may or may not be conservative based on the location of the resultant.
17
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 18/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Assume Pressure To Top
When the Rankine method is used to calculate the lateral pressure from a cohesive (c = nonzero) soil, it can
happen that the theoretical pressure distribution goes into tension towards the top of the wall. The programs
normal response in this case is to simply assume zero pressure in that region, but this option allows you
to specify (conservatively) that the pressure distribution is taken as extending all the way to the top of the
wall. Note that this feature is meaningless when either the Coulomb pressure theory is selected or when the
soil is non-cohesive (c=0).
Extend Backfill Pressure To Key Bottom
For walls that have a key beneath the footing, this option causes the various lateral pressures from the
backfill side to extend to the bottom of the key, rather than just to the bottom of the footing.
Use Toe Passive Pressure for Bearing
Whether to include the passive pressure at the toe when determining bearing pressure. See the Bear-
ing/Friction tab in the Force Calcs View for an illustration of the effects of this option. This option will tend
to lessen the overturning effect and hence ’even out’ the bearing pressure for common loading scenarios, so
is often unconservative. Consider carefully before using this option.
3.1.3 Stability Criteria
These are definitions of the inputs in the ’Stability Criteria’ group.
Required F.S. for OT
The required factor of safety for overturning. If the option to specify different safety factors for seismic
loading is chosen, then this factor will be used only for an overturning moment based on non-seismic loads.
Required F.S. for Sliding
The required factor of safety for sliding. If the option to specify different safety factors for seismic loading
is chosen, then this factor will be used only for a sliding force based on non-seismic loads.
Has Different Safety Factors for Seismic
Allows you to specify different factors of safety (for sliding and overturning) that are used with seismicloading. If this option is chosen, the factors of safety will be separately calculated and checked for the
seismic case and for the non-seismic case.
Seismic F.S. for OT
The required factor of safety for overturning, where the overturning moment includes seismic loads.
18
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 19/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Seismic F.S. for Sliding
The required factor of safety for sliding, where the sliding force includes seismic loads
Allowable Bearing Pressure
The maximum allowable bearing pressure.
Req’d Bearing Location
The required position of the bearing pressure resultant beneath the footing.
3.1.4 Geotechnical
These are definitions of the inputs in the ’Geotechnical’ group.
Wall Friction Angle
The wall friction angle is a measure of the friction between the wall and the mass of retained soil. It is only
used if the lateral backfill pressure is calculated via the Coulomb method.
Friction Coefficent
This coefficent is a measure of the friction beneath the bottom of the footing and the soil below. It is the
ratio of the maximum friction force over the total vertical force.
Soil Modulus
The modulus of subgrade reaction for the soil beneath the footing. This value is used in calculating how
much the rotation of the footing due to settlement contributes to the displacement at the wall. This value is
typically provided by a geotechnical engineer.
3.2 Load Case Inputs
19
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 20/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
3.2.1 General
These are definitions of the inputs in the ’General’ group.
Name
The name of this load case.
3.2.2 Backfill
These are definitions of the inputs in the ’Backfill’ group.
Backfill Depth
The height of the backfill surface, measured from the point where it contacts the wall stem down to either
the subgrade surface (over the toe), the footing top, or the footing bottom, depending on the setting of the
’Measured From’ field.
20
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 21/51
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 22/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Water Table Depth
The depth of the water table, measured from the top of the footing.
Water Unit Weight
The unit weight of the water in the backfill.
Saturated phi-sat
The saturated internal friction angle (phi) of the backfill beneath the water table. Note you will not see this
option in the event that you have chosen the option to use equivalent fluid density; it is not needed in that
case.
Saturated Weight gamma-sat
The saturated unit weight or density of the portion of the backfill beneath the water table.
3.2.4 Passive Pressure @ Toe
These are definitions of the inputs in the ’Passive Pressure @ Toe’ group.
Analysis Type
Specifies the method that will be used to calculate the lateral passive pressure from the soil in front of the
toe. The Rankine and Coulomb methods are earth pressure theories that account for internal soil friction,whereas Equivalent Fluid Pressure (EFP) simply treats the soil as a fluid with a specified density. You can
also neglect this pressure entirely.
Friction Angle (phi)
The internal friction angle (phi) of the soil in front of the toe. Note you will not see this option in the event
that you have chosen the option to use equivalent fluid density; it is not needed in that case.
Cohesion (c)
The cohesion of the soil in front of the toe. Note you will not see this option in the event that you have
chosen the option to use equivalent fluid density; it is not needed in that case.
Equiv. Fluid Density
The equivalent fluid density of the soil in front of the toe. Note you will only see this option in the event
that you have chosen the option to use equivalent fluid density; it is not needed otherwise.
22
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 23/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Unit Weight (gamma)
The unit weight or density of the soil in front of the toe.
Apply Only To Key
Whether to apply passive pressure only to the key. Otherwise the pressure will be applied to the entire burial
depth, less that which has been ignored.
Soil Depth To Ignore
The depth of material over the toe to ignore when calculating the passive pressure. This must be less than
or equal to the burial depth of the footing, or to the depth of the key bottom if there is a key. A higher value
is more conservative.
3.2.5 Surcharge (Uniform)
These are definitions of the inputs in the ’Surcharge (Uniform)’ group.
Surcharge Type
Specifies whether there is a uniform surcharge over the backfill, and whether that surcharge is specified
directly as a pressure, or as additional depth of backfill.
Surcharge Pressure
The surcharge pressure on top of the backfill.
Add’l Backfill Depth
The specified additional depth of backfill from which the surcharge pressure will be calculated.
3.2.6 Surcharge (Line/Strip)
These are definitions of the inputs in the ’Surcharge (Line/Strip)’ group.
Type
Choose either a line or a strip surcharge on the backfill. A line surcharge is applied at a specified distance
from the wall and has units of force per unit length of the wall. A strip surcharge is applied over a finite
width at a specified distance from the wall and has pressure units.
23
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 24/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Depth
The depth below the backfill surface at which the line or strip surcharge is applied. This is useful, for
example, if there is a buried footing in the backfill. This depth is measured from the backfill surface at the
point where it contacts the wall, not the sloped surface (if the the backfill is sloped).
Distance From Stem
If a line surcharge is applied, this is the lateral distance from the point where the backfill surface contacts the
stem to the point at which the line load is applied. If a strip surcharge is applied, this is the lateral distance
from the point where the backfill surface contacts the stem to the start of the strip surcharge pressure.
Width
This is the width of the strip surcharge pressure. This input is not available for a line surcharge.
Pressure
The magnitude of the strip surcharge (pressure).
Force
The magnitude of the line surcharge (linear force).
3.2.7 Uniform Lateral Load
These are definitions of the inputs in the ’Uniform Lateral Load’ group.
Apply Lateral Pressure To Stem
Choose this option if you would like to manually specify a lateral pressure on the stem.
Magnitude
The magnitude of the manually specified lateral pressure on the stem. The pressure acts in the same direc-
tion as the backfill pressure, as indicated on the diagram.
Top Bound
The distance from the top of the stem to the top of the lateral pressure distribution.
Bottom Bound
The distance from the top of the stem to the bottom of the lateral pressure distribution.
24
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 25/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Load Source
The load source for the uniform lateral pressure.
3.2.8 Stem Axial Load
These are definitions of the inputs in the ’Stem Axial Load’ group.
Has Axial Load on Stem
This option allows you to specify a vertical, downward force on the top of the stem, with an optional
eccentricity.
Dead LoadThe magnitude of the dead load component of the axial force.
Live Load
The magnitude of the live load component of the axial force.
Eccentricity
Enter the eccentricity of the stem load. Only positive eccentricities are allowed (move the load out towards
the end of the toe). The eccentricity is measured from the center of the top of the stem.
3.2.9 Seismic Loading
These are definitions of the inputs in the ’Seismic Loading’ group.
Has Backfill Seismic Load
This option applies a lateral force from the mass of backfill due to earthquake effects.
Kh
The horizontal seismic coefficient, which is the horizontal earthquake acceleration component divided by
the acceleration due to gravity.
Kv
The vertical seismic coefficient, which is the vertical earthquake acceleration component divided by the
acceleration due to gravity.
25
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 26/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Friction Angle (phi)
The internal friction angle (phi) of the backfill soil, as used in seismic calculations. This is usually specified
in the ’Backfill’ inputs and cannot be modified here, but if the backfill pressure is calculated via EFP
(Equivalent Fluid Pressure) or at-rest, then phi must be entered here.
3.3 Wall (Footing/Stem) Inputs
Name
The name of this wall. It is useful to give walls meaningful names to distinguish them from other stored
walls.
26
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 27/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
3.3.1 General
These are definitions of the inputs in the ’General’ group.
Burial Depth
The distance from the lower grade surface to the bottom of the footing.
3.3.2 Material
These are definitions of the inputs in the ’Material’ group.
Rebar Fy
The specified yield stress of the reinforcing bars. This value will also be used for the stem unless the option
’Material Properties Different Than Footing’ is chosen for the stem.
Concrete f’c
The specified compressive strength of the concrete. This value will also be used for the stem unless the
option ’Material Properties Different Than Footing’ is chosen for the stem.
Unit Weight
The density, or unit weight, of the material (concrete) used to construct the footing. This value will also be
used for the stem unless the option ’Material Properties Different Than Footing’ is chosen for the stem.
3.3.3 Footing Geometry
These are definitions of the inputs in the ’Footing Geometry’ group.
Footing Thickness
The thickness of the footing (heel and toe).
Heel Length
The length of the heel as measured from the base of the stem.
Toe Length
The length of the toe as measured from the base of the stem.
27
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 28/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Link Footing Bar Spacing to Stem
Synchronizes the spacing of the footing reinforcement to the spacing of the stem reinforcement.
3.3.4 Heel Reinforcement
These are definitions of the inputs in the ’Heel Reinforcement’ group.
Has Heel Reinforcement
You can uncheck this box to specify that there is no reinforcement for the heel, for example when the heel
is extremely short.
Embedment TypeThe manner in which the heel reinforcement is embedded in the rest of the wall. The bars with either extend
straight the full width of the footing, extend straight a specified distance past the junction with the stem, or
will hook downward. The hook option can be necessary when the toe is too short for the heel bars to be
developed by extending straight into the toe. Note that in practice, it may be necessary to tilt these bars,
since the footing may not be thick enough to accommodate the required hook extension.
Heel Bar Size
The size of the heel reinforcing bars.
Heel Bar Spacing
The center to center spacing of the heel reinforcing bars. If ’Link Footing Bar Spacing to Stem’ is selected,
this reinforcement spacing will be controlled by the stem reinforcement spacing.
Heel Bar Ld
The distance that the heel bars extend into the footing past the base of the stem (the critical section for
flexure).
Heel Bar Cover
The clear cover between the heel bars and the top of the heel.
3.3.5 Toe Reinforcement
These are definitions of the inputs in the ’Toe Reinforcement’ group.
28
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 29/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Has Toe Reinforcement
You can uncheck this box to specify that there is no reinforcement for the toe, for example when the toe is
extremely short.
Embedment Type
The manner in which the toe reinforcement is embedded in the rest of the wall. The bars with either extend
straight the full width of the footing, extend straight a specified distance past the junction with the stem, or
will hook up to become stem reinforcement. If the hook option is chosen, there will be no separate inputs
for specifying the toe bars; they will be consistent with the bars at the base of the stem.
Toe Bar Size
The size of the toe reinforcing bars.
Toe Bar Spacing
The center to center spacing of the toe reinforcing bars. If ’Link Footing Bar Spacing to Stem’ is selected,
this reinforcement spacing will be controlled by the stem reinforcement spacing.
Toe Bar Ld
The distance that the toe bars extend into the footing past the base of the stem (the critical section for
flexure).
Toe Bar Cover
The clear cover between the toe bars and the bottom of the toe.
3.3.6 Transverse Reinf. (S&T)
These are definitions of the inputs in the ’Transverse Reinf. (S&T)’ group.
Footing Has Transverse (S&T) Bars
Whether or not the footing has transverse (shrinkage temperature) reinforcement, top and bottom.
Transverse Bar Size
The size of the footing transverse (shrinkage temperature) reinforcing bars.
29
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 30/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Transverse Bar Spacing
The maximum center to center spacing of the footing transverse (shrinkage temperature) reinforcing bars.
The actual detailed bar spacing may be slightly less, as the program will evenly distribute the bars over the
footing width.
3.3.7 Key
These are definitions of the inputs in the ’Key’ group.
Has Key
Use this option to indicate that the wall has a shear key in order to help with sliding resistance.
Key Depth
The depth of the shear key, measured from the bottom of the footing to the bottom of the key.
Key Width
The width of the shear key.
Key Position
The position of the shear key beneath the footing. If ’Encase Bars’ is chosen, the key is positioned hori-
zontally such that the stem bars will extend down into it, and such that they will also tend to reinforce thekey.
Key Location
The manually specified location of the shear key, measured from the left edge (toe) of the footing to the left
edge of the key. This entry is only available if ’Key Position’ is set to ’Specified’.
3.3.8 General
These are definitions of the inputs in the ’General’ group.
Stem Type
Whether the stem will be composed of multiple pieces of differing thicknesses.
30
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 31/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Height
This governs the height of the stem, measured from either the footing bottom, footing top, the backfill
surface, depending on the setting of the ’Measured From’ field.
Measured From
Specifies how the stem height will be specified. The ’Backfill Surface’ option will cause the same behavior
used in QuickRWall 1.5, where the stem height is always set relative to the backfill depth.
Bars Developed @ Top
By checking this option you indicate that the bars that extend to the top of the stem are developed by some
external means that is not directly specified in the program. This is necessary when there is an eccentric
axial load applied to the top of the stem, since there will in that case be a moment at the top of the stem.Without development of the bars at the top, there would be no moment capacity there, and so the stem
would be considered inadequate.
Has Lateral Support (Restrained Wall)
This option allows you to specify a lateral support on the stem. This is frequently used to model the
’basement wall’ or ’restrained wall’ condition. Choosing this option changes the available inputs for rein-
forcement, since the different applied moment caused by the support will require reinforcement at different
locations.
Support Top Offset
Specifies the position of the lateral support, as measured from the top of the wall. Leave this value at zero
to have the support at the top.
Stem Base Is Pinned
When there is a lateral support, you have the option of treating the stem-footing connection as pinned.
Material Properties Different Than Footing
Check this box to enter different concrete material properties for the stem than for the footing. If this box
is not checked, the properties entered for the footing will also be used for the stem.
Rebar Fy
The specified yield stress of the reinforcing bars in the stem.
31
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 32/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Concrete f’c
The specified compressive strength of the concrete in the stem.
Unit Weight
The density, or unit weight, of the material (reinforced concrete/masonry) used to construct the stem.
3.3.9 Geometry
These are definitions of the inputs in the ’Geometry’ group.
Stem Top Thickness
The thickness of the stem at its top. If the wall is not tapered, this will be the constant thickness from top to
bottom.
Tapered
Check this box to taper the stem.
Extra Thickness @ Toe
The amount by which the bottom of the stem is thicker than the top on the toe side. This will be zero if the
stem is not tapered on the toe side.
Extra Thickness @ Heel
The amount by which the bottom of the stem is thicker than the top on the heel side. This will be zero if the
stem is not tapered on the heel side.
3.3.10 Reinforcement (Flexural)
These are definitions of the inputs in the ’Reinforcement (Flexural)’ group.
Reinforcement Layout
This setting determines whether there will be one or two curtains of reinforcement in the stem, and the
position for cases where there is just one curtain.
Vertical Bar Size
The size of the main vertical reinforcing bars.
32
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 33/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Vertical Bar Spacing
The center to center spacing of the vertical reinforcing bars.
Vertical Bar Embedment
The manner in which the stem reinforcement is embedded in the footing. The bars can either extend straight
down into the footing (and possibly into the shear key, if there is one), or hook into the heel, or hook into
the toe, in which case they also serve as toe reinforcement.
Vertical Bar Ld
The distance the main vertical bars in the stem extend into the footing (when they aren’t hooked).
Cut Off Alternate Bars
Choose this option to specify that every other bar is cut off and hence does not extend all the way to the top
of the stem. If the lapped bar option is also chosen, this means that the (alternate) cutoff bars will not be
lapped but will consist of the dowels extending up to the cutoff point.
Cutoff Length
The distance from the base of the stem to the cutoff point for the cutoff bars.
Lap With Dowels
Use this option to have the stem dowels lapped with other bars at the base of the stem. This might be every
bar or every other bar depending on whether the ’cut off alternate bars’ option is chosen.
Lap Length
The distance over which the bars are lapped. This is measured starting at the base of the stem.
Dowel Bar Size
The size of the dowels that lap with the main vertical reinforcing bars.
Cover (backfill side)
The clear cover between the stem bars and the outer surface of the stem on the backfill side.
33
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 34/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Cover (toe side)
The clear cover between the stem bars and the outer surface of the stem on the toe side (side opposite the
backfill).
2nd Layer Bar Size
The size of the vertical reinforcing bars in the second layer. The second layer is the one near the face of the
wall furthest from the backfill (on the ’toe side’).
2nd Layer Bar Spacing
The center to center spacing of the vertical reinforcing bars in the second layer.
2nd Layer Bar Embedment
The manner in which the 2nd layer stem reinforcement is embedded in the footing. The bars can either
extend straight down into the footing (and possibly into the shear key, if there is one), or hook into the heel,
or hook into the toe.
2nd Layer Bar Ld
The distance the 2nd layer vertical bars in the stem extend into the footing (when they aren’t hooked). It
is conceivable that this value will often be left at zero, since most loading configurations will not require
positive moment capacity at the stem base.
3.3.11 Reinforcement (S&T)
These are definitions of the inputs in the ’Reinforcement (S&T)’ group.
Has Horizontal (S&T) Bars
Whether or not the stem has horizontal (shrinkage & temperature) reinforcement.
Horizontal Bar Size
The size of the stem horizontal (shrinkage & temperature) reinforcing bars.
Horizontal Bar Spacing
The center to center spacing of the stem horizontal (shrinkage & temperature) reinforcing bars.
34
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 35/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Same For Both Layers
Whether or not the size and spacing of the horizontal reinforcement in the stem is the same for both layers
of bars. De-select this option to specify separate bar size & spacing for the 2nd layer.
2nd Layer Horz Bar Size
The size of the stem horizontal (shrinkage & temperature) reinforcing bars in the second layer.
2nd Layer Horz Bar Spacing
The center to center spacing of the stem horizontal (shrinkage & temperature) reinforcing bars in the second
layer.
3.3.12 Sections
These are definitions of the inputs in the ’Sections’ group.
Number of Stem Sections
Specify the number of sections that make up the stem. Each section may have its own thickness and
reinforcement.
3.4 Stem Section Inputs
3.4.1 General
These are definitions of the inputs in the ’General’ group.
Type
This entry specifies whether this section of the stem will be constructed of concrete or masonry.
35
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 36/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Height
The height of this section of the stem.
Thickness
The thickness of this section of the stem.
3.4.2 Masonry Block
These are definitions of the inputs in the ’Masonry Block’ group.
Masonry f’m
The specified compressive strength of the masonry.
Block Thickness
Thickness of the masonry block used in this section.
3.4.3 Reinforcement
These are definitions of the inputs in the ’Reinforcement’ group.
Bar Fs
The allowable tensile or compressive stress in the reinforcement.
Bar Size
The size of the reinforcing bars in this section of the stem.
Bar Spacing
The center to center spacing of the reinforcing bars in this section of the stem.
Bar Position
The bar position relative to the outer faces of the wall.
36
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 37/51
QuickRWall 3.0 User’s Guide CHAPTER 3. USER INPUTS
Bar Cover
The clear cover between the bar and the nearest face. This input is not meaningful or visible if the bars are
centered in the wall.
Embedment Above
Distance the bars from this section extend into the section above. This input is not available for the top
section.
Embedment Below
Distance the bars from this section extend into the section below.
Base Embedment Type
Determines the manner in which the bars that extend down from the bottom section are embedded into the
footing.
37
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 38/51
Chapter 4
Forces on the Wall
4.1 Overview
The software allows loading the wall via the following sources:
• Lateral pressure from the backfill
• Lateral pressure from water in the backfill
• Passive lateral pressure at the toe
• Surcharge on the backfill (uniform)
• Surcharge on the backfill (line/strip)
• Manually specified lateral pressure (e.g. from wind)
• Lateral pressure due to seismic loads
• Axial load on stem
• Weight of the wall
• Weight of the soil (backfill & soil above toe)
• Bearing reaction beneath the footing
• Friction between the footing and soil
4.1.1 Forces Used for Stem Design
For most of these loading types, the calculations will show a second set of results on the stem only, in
addition to the initial set on the full wall. These stem-only forces are used for calculating the internal shears
and moments for stem design.
4.1.2 Multiple Load Cases
If there are multiple load cases then there will be multiple sets of results for each of these loading types.
When viewing the results (on the ’Force Calcs View’ tab), you can switch between load cases using the
drop-down list at the bottom of the screen.
4.2 Backfill Pressure
38
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 39/51
QuickRWall 3.0 User’s Guide CHAPTER 4. FORCES ON THE WALL
The retained backfill will exert a horizontal pressure on the wall. The backfill pressure can be arrived at in
one of two ways:
• Specified directly as an equivalent fluid pressure (EFP)• Calculated by the program using active earth pressure theory (Rankine or Coulomb) or at-rest earth
pressure theory.
When you specify an equivalent fluid pressure (EFP) you are telling the program directly what the pressure
per unit depth is. This information might come from a geotechnical engineer or a soils report. This is a
very simple calculation where the lateral pressure is calculated as if the backfill was a fluid with the given
density gamma-EFP. The resulting distribution varies linearly from a maximum value of gamma-EFPH x H
at the bottom of the footing up to zero at the top.
When the program calculates the backfill pressure itself, it employs either Rankine active, Coulomb active,
or at-rest earth pressure theory. Active earth pressure is most reasonable for a cantilever wall due to its
tendency to displace somewhat in response to loading, hence allowing the backfill’s internal friction to
engage in helping to restrain any further movement. Restrained walls are usually designed using at-rest
pressure.
If there is water in the backfill, the buoyant effect of the water will reduce the lateral pressure from the
portion of the backfill that is below the water surface. The total lateral force over that portion, however, will
increase when the pressure due to the water itself is considered (see following section).
4.3 Water Pressure
If there is water in the backfill, it will exert a lateral pressure on the wall. The magnitude of the pressure is
determined by a simple hydrostatic calculation (pressure = depth multiplied by the unit weight of water).
The unit weight of water defaults to 64 pcf but can be manually overridden by the user.
4.4 Passive Pressure @ Toe
The soil that is in front of the wall (over and in front of the toe) can also exert a pressure on the wall. The
extent of this pressure will vary based on how much overburden you choose to neglect, whether a shear key
is present, and on whether you opt to neglect the portion of the pressure above the bottom of the footing.
This passive pressure contributes to sliding and (possibly) overturning resistance and can play an important
role in ensuring the stability of the wall. Sometimes the fact that the soil in front of the toe gets disturbed
during excavation, or other concerns, will cause concern over whether including a passive pressure contri-
bution from that soil is reasonable. For this reason the program allows you to indicate that such pressure is
to be excluded from the calculations.
The passive pressure can either be calculated via Rankine passive theory, specified directly with an equiva-
lent fluid density value, or neglected completely.
4.5 Uniform Surcharge
The program allows you to specify a uniform surcharge in one of two ways:
39
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 40/51
QuickRWall 3.0 User’s Guide CHAPTER 4. FORCES ON THE WALL
• Specify a fictitious additional depth of backfill
• Specify a uniform pressure on the backfill
If an additional depth of backfill is specified, it is converted to a pressure internally and then lateral forcecalculations proceed using that pressure.
The surcharge pressure results in a uniform lateral pressure on the wall, which is the vertical (surcharge)
pressure multiplied by the lateral pressure coefficient. If Rankine or Coulomb active pressure was used
for determining backfill pressure, K is the calculated Ka value for active pressure (similarly Ko for at-rest
pressure). If EFP was used for backfill pressure, K is determined by dividing the weight of the backfill
(gamma) by the specified equivalent fluid density.
4.6 Line/Strip Surcharge
You may apply either a line or strip surcharge on the wall. The corresponding lateral pressures are calculated
using the methods outlined in the text Principles of Foundation Engineering by Braja M. Das, 3rd Edition.
The exact equation used for a given loading is displayed in the output.
This loading requires particularly complicated mathematical routines that can cause a noticeable delay in
the software. If you notice such a delay after changing a parameter that affects the pressure (e.g. the retained
height of backfill), this is normal.
4.7 Seismic Loading
The program applies a seismic load due to the weight of the backfill based on the Mononobe-Okabe method.
The equations used to calculate the exact force are displayed in the program output.
Take note when examining the pressure distribution on the stem. The theory gives two constraints: That the
shape of the pressure distribution is an inverted triangle, and that the resultant acts at 0.6H from the bottom
of the wall. Since these two conditions are mutually exclusive (resultant for a perfect triangular distribution
would be at 2/3 or 0.667H from bottom) the program slightly modifies the distribution, increasing the
bottom magnitude from zero such that the resultant drops to 0.6H. This is the pressure that is used when
calculating stem moments.
4.8 Wall Weights
The wall weights are determined by dividing the wall into simple geometric pieces and calculating the
weight for each piece. Each piece’s weight (per unit length of wall) is the area of the piece multiplied by
the unit weight of the wall material.
4.9 Soil Weights
The soil weights are determined by dividing the backfill into simple geometric pieces and calculating the
weight for each piece. Each piece’s weight (per unit length of wall) is the area of the piece multiplied by
40
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 41/51
QuickRWall 3.0 User’s Guide CHAPTER 4. FORCES ON THE WALL
the unit weight of the soil. This includes both the backfill behind the wall and the soil in front of the wall
over the toe. The weight of the soil over the toe can be neglected if desired.
4.10 Bearing Reaction
The upward force (R) exerted by the soil against the footing is in reaction to the sum of all downward
forces that act on the wall. The calculations displayed in the software show exactly what the various
downward forces are. Note that the software also tabulates what contribution each load source (e.g. dead,
live, etc.) makes to the total bearing reaction. This information may be of general interest, and also becomes
important when factoring the bearing pressure and determining the sliding resistance due to friction, which
is a function of this bearing resultant.
The horizontal position at which R acts is determined by calculating the net moment of all the forces on the
wall and dividing by R. See the program output for sample equations. Note that for a restrained wall the
contribution of lateral forces to the overall moment is not added in directly; rather, their effect is reflectedin the moment that is transferred to the footing at the base of the stem (Mstem).
Knowing R and dR it is then possible to calculate the left and right bearing pressures beneath the footing.
The formula used for this will vary based on whether the resultant R is located inside the middle third (full
bearing) or outside the middle third (partial bearing). Again, the best illustration of this is to look at the
program output.
4.11 Friction
The friction between the footing and the soil below is calculated by multiplying a user-specified coefficient
by the total bearing reaction force. This is a fairly straightforward calculation, but there are complicating
adjustments made when some portion of the bearing pressure was in reaction to certain load sources that
should not be allowed to contribute to frictional resistance. These sources are:
• Any live loads
• Applied surcharge force (vertical) - (optional based on user setting)
• Vertical component of backfill force - (optional based on user setting)
If the bearing reaction contains contributions from any of these three sources, it will be reduced for the
purposes of calculating friction. The printed report details how the calculations are adjusted to reflect this
reduction.
41
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 42/51
Chapter 5
Checks
5.1 Stability Checks
5.1.1 General Notes
The following general notes apply to all stability checks:
• The applied forces (calculated on the overall wall plus the backfill over the heel) used in stability
checks are factored according the the load combination specified by the ’Stability Load Comb’ input
on the Criteria tab of the Input View. The default combination has all factors set to 1.0 (unfactored).
• Several of the options on the Criteria tab (Input View) under the ’Assumptions’ group affect stability
checks. Make sure to examine these settings and ensure that they are correct for your particularproject.
• The results displayed by the software (Checks View, Stability tab) thoroughly illustrate the details of
how the checks are performed. Refer to this output for a better understanding of the internal workings
of these checks.
• In the sliding check, the lateral support reaction (visible for restained walls) will be calculated based
on the load combination used for stability checks (as selected on the Criteria tab). This is not neces-
sarily the same as any of the strength combinations, so you should not expect the value shown to be
the same as that displayed for strength design of the stem.
5.1.2 Checks Performed
These are the checks that are made to ensure stability.
42
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 43/51
QuickRWall 3.0 User’s Guide CHAPTER 5. CHECKS
Overturning
Code References:
• IBC 2003 1806.1
• IBC 2006 1806.1
• IBC 2009 1807.2
Checks that the factor of safety against overturning is greater than or equal to the specified minimum
allowable.
Sliding
Code References:
• IBC 2003 1806.1
•
IBC 2006 1806.1• IBC 2009 1807.2
Checks that the factor of safety against sliding is greater than or equal to the specified minimum allowable.
Bearing Pressure
Code References:
• IBC 2003 1806.1
• IBC 2006 1806.1
• IBC 2009 1807.2
Checks that the maximum bearing pressure (gross pressure) beneath the footing is less than or equal to the
specified minimum allowable.
Bearing Eccentricity
Code References:
• IBC 2003 1806.1
• IBC 2006 1806.1
• IBC 2009 1807.2
Checks that the bearing pressure resultant eccentricity (distance from footing center) does not exceed the
allowable.
5.2 Stem Checks
5.2.1 General Notes
The following general notes apply to the stem checks:
43
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 44/51
QuickRWall 3.0 User’s Guide CHAPTER 5. CHECKS
• The applied forces (e.g. backfill pressure) used to calculate the internal forces in the stem are illus-
trated on the Stem Forces tab of the Checks View. These forces are calculated independently from
the forces on the overall wall; take note of the ’stem-only’ set of calculations on the Backfill tab and
other tabs of the Analysis View.
• The forces used in stem design are factored by the strength load combinations selected on the Criteria
tab of the Input View, specifically the ’Concrete Load Combs’ and/or ’Masonry Load Combs’ inputs.
• When viewing stem check results. note that most of the tabs in the Checks View display information
for the selected load case, which is chosen by a drop-down list at the bottom of the window. If the
stem contains both concrete and masonry, the window will show both the concrete load combination
and best-matched masonry combination, and internal force graphs (moment/shear) will plot results
for both combinations.
• If the stem is unreinforced, ACI’s ’structural plain concrete’ provisions are used for design (ACI-318
Ch. 22).
5.2.2 Checks Performed
Specific code checks associated with the stem.
Moment
Code References:
• ACI 318-02 10.2, 10.3
• ACI 318-05 10.2, 10.3
• ACI 318-08 10.2, 10.3
• CSA-A23.3-94 Ch 10
• CSA-A23.3-04 Ch 10
Checks the stem for flexural failure according to the selected design code. This check is performed at
multiple critical locations along the height of the stem, depending on configuration and loading.
Shear
Code References:
• ACI 318-02 11.1.1, 11.3.1
• ACI 318-05 11.1.1, 11.3.1
• ACI 318-08 11.1.1, 11.2.1
• CSA-A23.3-94 11.3
44
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 45/51
QuickRWall 3.0 User’s Guide CHAPTER 5. CHECKS
• CSA-A23.3-04 11.3
Checks the stem for shear failure according to the selected design code. This check is performed at multiple
critical locations along the height of the stem, depending on configuration and loading.
Max Steel
Code References:
• ACI 318-02 10.3.5
• ACI 318-05 10.3.5
• ACI 318-08 10.3.5
Checks the stem for sufficient tensile strain at nominal strength. This is a ductility requirement that guards
against over-reinforcement.
Min Steel
Code References:
• ACI 318-02 10.5.1
• ACI 318-05 10.5.1
• ACI 318-08 10.5.1
• CSA-A23.3-94 10.5.1
• CSA-A23.3-04 10.5.1
Checks the toe for sufficient area of flexural reinforcement.
Base Development
Code References:
• ACI 318-02 12.2.3, 12.12
• ACI 318-05 12.2.3, 12.12
• ACI 318-08 12.2.3, 12.12
• CSA-A23.3-94 Ch 12
• CSA-A23.3-04 Ch 12
Checks that the stem bars are sufficiently developed into the footing.
Lap Splice Length
Code References:
• ACI 318-02 12.15.1, 12.15.2
• ACI 318-05 12.15.1, 12.15.2
• ACI 318-08 12.15.1, 12.15.2
• CSA-A23.3-94 Ch 12
• CSA-A23.3-04 Ch 12
Checks that the bar lap splices in the stem are long enough.
45
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 46/51
QuickRWall 3.0 User’s Guide CHAPTER 5. CHECKS
Lap Splice Spacing
Code References:
• ACI 318-02 12.14.2.3
• ACI 318-05 12.14.2.3
• ACI 318-08 12.14.2.3
• CSA-A23.3-94 Ch 12
• CSA-A23.3-04 Ch 12
Checks that the transverse spacing between lapped bars does not exceed the limit (for noncontact lap
splices).
Bar Cutoff Extension
Code References:
• ACI 318-02 12.10.3
• ACI 318-05 12.10.3
• ACI 318-08 12.10.3
• CSA-A23.3-94 12.10.3
• CSA-A23.3-04 12.10.3
Checks that cutoff bars extend a sufficient distance past where they are no longer needed for flexure.
Bar Cutoff Shear
Code References:
• ACI 318-02 12.10.5
• ACI 318-05 12.10.5
• ACI 318-08 12.10.5
• CSA-A23.3-94 12.10.5
• CSA-A23.3-04 12.10.5
For cutoff bars, checks that the shear does not exceed the allowable limit when bars are cut off in a tension
zone.
Horz Bar Rho
Code References:
• ACI 318-02 14.3.3
• ACI 318-05 14.3.3• ACI 318-08 14.3.3
Checks that the horizontal bars in the wall meet the minimum reinforcement percentage (rho).
Horz Min Steel
Code References:
46
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 47/51
QuickRWall 3.0 User’s Guide CHAPTER 5. CHECKS
• CSA-A23.3-94 14.1.8.6
• CSA-A23.3-04 14.1.8.6
Checks that the horizontal bars in the wall meet the minimum area.
Horz Bar Spacing
Code References:
• ACI 318-02 14.3.5
• ACI 318-05 14.3.5
• ACI 318-08 14.3.5
• CSA-A23.3-94 14.1.8.4
• CSA-A23.3-04 14.1.8.4
Checks that the horizontal bars in the wall do not exceed the maximum spacing.
5.3 Toe Checks
5.3.1 General Notes
The following general notes apply to the toe checks:
• The design shear force used for the toe is taken at a distance ’d’ from the base of the stem.
• The design moment for the toe is not taken greater than the design moment at the base of the stem.
• If the toe is unreinforced, ACI’s ’structural plain concrete’ provisions are used for design (ACI-318
Ch. 22).
• When factoring the bearing pressure for heel and toe checks, the program calculates an average load
factor based on the percentage contribution of each load source to the total bearing reaction.
5.3.2 Checks Performed
Specific code checks associated with the toe.
Shear
Code References:
• ACI 318-02 11.1.1, 11.3.1
• ACI 318-05 11.1.1, 11.3.1
47
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 48/51
QuickRWall 3.0 User’s Guide CHAPTER 5. CHECKS
• ACI 318-08 11.1.1, 11.2.1
• CSA-A23.3-94 11.3
• CSA-A23.3-04 11.3
Checks the toe for shear failure according to the selected design code.
Moment
Code References:
• ACI 318-02 10.2, 10.3
• ACI 318-05 10.2, 10.3
• ACI 318-08 10.2, 10.3
• CSA-A23.3-94 Ch 10
• CSA-A23.3-04 Ch 10
Checks the toe for flexural failure according to the selected design code.
Min Strain
Code References:
• ACI 318-02 10.3.5
• ACI 318-05 10.3.5
• ACI 318-08 10.3.5
Checks the toe for sufficient tensile strain at nominal strength. This is a ductility requirement that guards
against over-reinforcement.
Min Steel
Code References:
• ACI 318-02 10.5.1
• ACI 318-05 10.5.1
• ACI 318-08 10.5.1
• CSA-A23.3-94 10.5.1
• CSA-A23.3-04 10.5.1
Checks the toe for sufficient area of flexural reinforcement.
Development
Code References:
• ACI 318-02 12.2.3, 12.12
• ACI 318-05 12.2.3, 12.12
• ACI 318-08 12.2.3, 12.12
• CSA-A23.3-94 Ch 12
• CSA-A23.3-04 Ch 12
Checks that the toe bars are sufficiently developed into the rest of the wall.
48
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 49/51
QuickRWall 3.0 User’s Guide CHAPTER 5. CHECKS
S&T Max Spacing
Code References:
• ACI 318-02 7.12.2.2
• ACI 318-05 7.12.2.2
• ACI 318-08 7.12.2.2
• CSA-A23.3-94 7.8.3
• CSA-A23.3-04 7.8.3
Checks that the shrinkage and temperature (transverse) steel spacing does not exceed the allowable limit.
S&T Min Rho
Code References:
•
ACI 318-02 7.12.2.1• ACI 318-05 7.12.2.1
• ACI 318-08 7.12.2.1
Checks that the shrinkage and temperature (transverse) steel rho meets the minimum limit.
S&T Min Steel
Code References:
• CSA-A23.3-94 7.8.1
• CSA-A23.3-04 7.8.1
Checks that the shrinkage and temperature (transverse) steel area meets the minimum limit.
5.4 Heel Checks
5.4.1 General Notes
The following general notes apply to the heel checks:
• The design moment for the heel is not taken greater than the design moment at the base of the stem.
• If the heel is unreinforced, ACI’s ’structural plain concrete’ provisions are used for design (ACI-318
Ch. 22).
• When factoring the bearing pressure for heel and toe checks, the program calculates an average loadfactor based on the percentage contribution of each load source to the total bearing reaction.
5.4.2 Checks Performed
Specific code checks associated with the heel.
49
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 50/51
QuickRWall 3.0 User’s Guide CHAPTER 5. CHECKS
Shear
Code References:
• ACI 318-02 11.1.1, 11.3.1
• ACI 318-05 11.1.1, 11.3.1
• ACI 318-08 11.1.1, 11.2.1
• CSA-A23.3-94 11.3
• CSA-A23.3-04 11.3
Checks the heel for shear failure according to the selected design code.
Moment
Code References:
• ACI 318-02 10.2, 10.3
• ACI 318-05 10.2, 10.3
• ACI 318-08 10.2, 10.3
• CSA-A23.3-94 Ch 10
• CSA-A23.3-04 Ch 10
Checks the heel for flexural failure according to the selected design code.
Min Strain
Code References:
• ACI 318-02 10.3.5
• ACI 318-05 10.3.5
• ACI 318-08 10.3.5
Checks the heel for sufficient tensile strain at nominal strength. This is a ductility requirement that guards
against over-reinforcement.
Min Steel
Code References:
• ACI 318-02 10.5.1
• ACI 318-05 10.5.1
• ACI 318-08 10.5.1
• CSA-A23.3-94 10.5.1
• CSA-A23.3-04 10.5.1
50
7/24/2019 QuickRWall - Guía de Usuario
http://slidepdf.com/reader/full/quickrwall-guia-de-usuario 51/51
QuickRWall 3.0 User’s Guide CHAPTER 5. CHECKS
Checks the heel for sufficient area of flexural reinforcement.
Development
Code References:
• ACI 318-02 12.2.3, 12.12
• ACI 318-05 12.2.3, 12.12
• ACI 318-08 12.2.3, 12.12
• CSA-A23.3-94 Ch 12
• CSA-A23.3-04 Ch 12
Checks that the heel bars are sufficiently developed into the rest of the wall.
S&T Max Spacing
Code References:
• ACI 318-02 7.12.2.2
• ACI 318-05 7.12.2.2
• ACI 318-08 7.12.2.2
• CSA-A23.3-94 7.8.3
• CSA-A23.3-04 7.8.3
Checks that the shrinkage and temperature (transverse) steel spacing does not exceed the allowable limit.
S&T Min Rho
Code References:
• ACI 318-02 7.12.2.1
• ACI 318-05 7.12.2.1
• ACI 318-08 7.12.2.1
Checks that the shrinkage and temperature (transverse) steel rho meets the minimum limit.
S&T Min Steel
Code References:
• CSA-A23.3-94 7.8.1
• CSA-A23.3-04 7.8.1
Checks that the shrinkage and temperature (transverse) steel area meets the minimum limit.