rotaciÓn de la hÉlice
TRANSCRIPT
LIN
EA A
XIA
L - H
ÉLIC
ES A
XIA
LES
Casa central: Rosario de Santa Fe 298Tel (03564) 421022 / 420619 San Francisco (2400) - [email protected]
Suc. Buenos Aires: Independencia 998Tel (011) 4300-0607 / 0421Capital Federal - Bs [email protected]. Rosario: Salta 2998Tel (0341) 4354452 Rosario (2002) - Santa [email protected]
V E N T I L A C I Ó N
www.gattisa.com.ar F:/Gattisa T:/Gattisa
GENERALIDADES GENERALITIS
Pag. 2
Este diseño permite variar la cantidad de álabes, el ángulo y el diámetro de los mismos. Pueden ser armadas con flujos de aire motor/hélice, hélice/motor, o reversibles, es decir con álabes en los dos sentidos, permitiendo variar el senti-do del flujo automáticamente.
ÁLABES: Se fabrican en polipropileno y fibra de vidrio (PPG), y a pedido en poliamida y fibra de vidrio (PAG), materiales con excelentes propie-dades físicoquímicas. Todas las hélices presentan un perfecto balance, ya que poseen baja densidad, alta rigidez, bajo nivel de ruido, buena resistencia química y excelente performance frente al calor. También se fabrica un modelo en aluminio (AL), material que soporta temperaturas muy eleva-das, puede trabajar con aire filamentoso y tiene mayor vida útil.MASA: Se fabrican en PPG y a pedido algunos modelos en aluminio.
Cabinas de pintura, secaderos de madera, venti-lación industrial y agrícola, refrigeradores, eva-poradores, atomizadores para el campo, secado-ras de grano, aireación de silos, torres de enfria-miento, etc. Por curvas de performance solicite el software de selección.
Painting and drying rooms, industrial and agri-cultural ventilation, evaporators and refrigera-tors, atomizers, cereal drying, aeration of silos, cooling towers, etc.
To see performance curves ask for the impe-ller´s selection software.
BLADES: They are made in polypropylene and fibreglass (PPG) and if asked in polyamide and fibreglass (PAG), materials with excelent physical and chemical properties, with low density, high rigidness, heat resistance and low sound level.
There is also one model made of silumin (AL), material with greater heat - resistance and duration.
HUB: They are made of PPG or silumin if asked.
In all models it is possible to change blades number, material, position, inclination grades and to adjust diameter. They can be assembled with three different air flows: motor/blade,blade/motor and reversible, that is to say with blades in both senses.
APLICACIONES APPLICATIONS
ROTACIÓN DE LA HÉLICE Sentido: HorarioGiro: Derecho
Sentido: Anti horarioGiro: Izquierdo
D I
Dirección del flujo del aire
NOTA 1: cuando la hélice sea de chapa las posiciones 3,4,5 y 6 quedarán vacías.NOTA 2: las hélices de aluminio de ángulo variable son todas P (pesadas)
DETALLES CONSTRUCTIVOS CONSTRUCTIVE FEATURES
Pag. 3
COMO LEER LA CODIFICACIÓN
DATOS TÉCNICOS TECHNICAL DATA
1 7 82 3 654
KPP 242 8 / CP 850 / 45º / HM / E / I 9 10 11
1- TIPO ÁLABES: K (axial); W (helicoidal)2- MATERIAL DEL ÁLABE: P (PPG o polipropileno y fibra de vidrio); A (aluminio); L (poliamida y fibra de vidrio); C (chapa)3- TAMAÑO ÁLABE: L (liviana) ; P (pesada)4- TAMAÑO DE LA MASA: LIVIANA: 108, 134 y 242; PESADA: 140, 242 y 3305- CANTIDAD DE ÁLABES: - PARA HÉLICES AXIALES: LIVIANA: masa 108: 3 ; masa 134: 4 y 8; masa 242: 7 y 14 PESADA: masa 140: 3 ; masa 242: 4 y 8; masa 330: 2,3,4,6,8,9 y 12 PARA HÉLICES HELICOIDALES: LIVIANA: masa 108: 3; masa 134: 4; masa 242: 7 PESADA: masa 140: 3; masa 242: 4; masa 330: 4 y 66- MATERIAL DEL CENTRO: (CP) centro de polipropileno y fibra de vidrio; (CA) centro de aluminio; (CB) centro de polipropileno y fibra de vidrio con buje de aluminio.7- DIÁMETRO DE LA HÉLICE: en mm8- ÁNGULO DE INCLINACIÓN: de 25º a 50 º9- FLUJO DE AIRE: HM (hélice/motor); MH (motor/hélice)10- DIÁMETRO DEL EJE: en mm11- ROTACIÓN: IZQUIERDA (I); DERECHA (D) (solo para hélices KPP)
Diámetro álabesBlades diameter
(mm)
Material álabesBlades material
Tamaño álabesBlades size
Material MasaHub material
Ángulo Inclinación
Setting angle
Flujo del aireAir flow
Material bujeShaft supply
material
Tipo héliceBlades type
Perfil de álabesBlades profile
Tamaño MasaHub Size
Helicoidal
PPG
livianalight
350a / to630
Plano
2 y/and
4
PPG
25ºa / to45º
MHHM
PPGAL
132
Número álabesBlades number
300 a / to690
PPG
livianalight
PPG
25ºa / to 50º
Ax ial
Air- Foil
MHHM
PPGAL
132
4 y/and
8
Axial
PPG
livianalight
400a / to800
Air- Foil
PPG
25ºa / to 50º
MHHM
PPGAL
242
7 y/and
14
Axial
PPG
pesadaheavy
500a / to1130
Air- Foil
PPG
20ºa / to 50º
MHHM
PPGAL
242
4 y/and
8
Axial
PPG
pesadaheavy
600a / to1220
Air- Foil
PPG
20ºa / to50º
MHHM
PPGAL
330
3/4/6/9/12
Helicoidal
PPG
livianalight
Plano
400a / to740
PPG
25ºa / to45º
MHHM
PPGAL
242
7
Helicoidal
PPG
pesadaheavy
Plano
850a / to1410
20ºa / to 45º
PPG
MHHM
PPGAL
330
3y/and
6
242 242 330 242/330 132 242 242 330140 108 140
700a / to1320
20ºa / to 45º
PPGAL
242
4
Helicoidal
PPG
pesadaheavy
Plano
MHHM
PPG
PPG
livianalight
Axial
108
PPG
MHHM
PPG
Air- Foil
250a / to646
3
25ºa / to50º
3
140
Axial
PPG
pesadaheavy
PPG
400a / to1010
PPG
MHHM
15ºa / to50º
Air- Foil
Helicoidal
PPG
livianalight
108
3
PPG
PPG
25ºa / to 45º
MHHM
Plano
300a / to590
Helicoidal
PPG
pesadaheavy
Plano
PPG
MHHM
140
3
PPG
580a / to1200
15ºa / to45º
108
Axial
AL
pesadaheavy
Air- Foil
AL
MHHM
600a / to1220
242 330
3/4/6/
9/12
4y/
and8
15ºa / to45º
AL
480
Axial
PPG
pesadaheavy
1100a / to1360
Air- Foil
AL
25ºa / to 45º
MHHM
AL
480
4/8/12/16
480
Axial
AL
pesadaheavy
1100a / to1360
Air- Foil
AL
25ºa / to 45º
MHHM
AL
480
4/8/12/16
480
PPG
pesadaheavy
1200a / to1560
Plano
AL
25ºa / to 45º
MHHM
AL
480
4 y/and
8
Helicoidal