rpms - images-na.ssl-images- · pdf filethe rpms are so low that the friction from the floor...

Poolvergnuegen PoolCleaner Troubleshooting.

1

RPMS

The most common problem (95% of the time)is that the unit is not getting enough suction or getting

way too much. You cannot see the difference between fast and slow with the naked eye! Often the

Previous cleaner didn’t work due to lack of suction or it was so worn they had to crank up the suction.

When we look at the unit we always look at the unit from behind. As if it is a car driving AWAY from us.

We always count the RPMs (Revolutions per minute… how many times the wheel turns around in one

minute ) on the right front wheel (looking from behind). The reason for this is that the left front wheel

has the steering system and it alternates between forward and backwards. So any counting of the

alternating turns does not result in any number that is measureable. In other words count the wheel

that only goes one direction!

SYMPTOMS

Very High RPMS

Cleaner is falling on its side (this can also be floats on leader hose missing).

Cleaner is doing wheelies and tipping backward.

Cleaner is slipping a little because it can’t pull the hose fast enough.

Climbs out and sucks air constantly (this can also be worn tires).

Cleaner is not covering pool. The Cam is made to work in the proper range of RPMS. So it will

seem like it is turning a lot. Key here is that it turns BUT goes straight in between. If it is just

turning never going straight there is something wrong with the steering.

Very low RPMS

Cleaner is not covering pool.

Cleaner gets stuck in corners. Or hung up on things.

Cleaner is falling on its side (this can also be floats on leader hose missing).

Cleaner stutters. Stop Go Stop Go. The rpms are so low that the friction from the floor stops the

cleaner. (They say it works when the wiggle hose. Or if it isn’t touching floor. You can hold the

cleaner 2 ft under the water and jump start the right front wheel and it will turn and you get

something ridiculous like 3 to 5 rpms.)

Hoses coil (this can also be the swivel on the head is dirty).

Cleaner won’t climb.


2

NOTE: Here is a trick that we do on the phone when checking RPMS with the customer. During

the discussion we typically mention the RPMS should be between 11 and 14. Since homeowners

and pool guys alike tend to lie about the actual RPMS when we check it on the phone with them

we time them to only 30 seconds and have them count the RPMS. So whatever the result is, you

multiply by 2 for the actual RPMS. If they say 14 or whatever they are typically lying. So we

explain that we can’t help them unless they actually do it. They are usually surprised that we

caught them and will then actually count the RPMS with us on the phone and it is always

something super low.

2 Wheel PoolCleaner vs 4 Wheel PoolCleaner when to use which one?

We typically use this example to illustrate which cleaner.

An easy way to determine if you need a 2 Wheel Suction PoolCleaner or a 4 Wheel Suction PoolCleaner

is to imagine a 40 ft long pool. If the suction port or skimmer is half way (most newer pools) approx 20 ft

from one end, then the 2 Wheel Model will be the right one.

If however the suction port is all the way at one end AND you have a very deep end (diving pools) the 4

Wheel PoolCleaner would be better suited for your pool.

The best way to describe it is that the 4 Wheel model can drag more hose.

The 2 Wheel unit comes with about (10 meters= 9 vacuum and one leader hose) 33 ft of hose. You can

safely add two; max 3 lengths of hoses to it and then the hoses will outweigh the cleaner and pull it

back. The 2 Wheel has a steering cam (program) that makes it turn 5 times in a cycle. So it turns more

often to cover an average sized pool

The 4 Wheel unit comes with about (12 meters = 11 vacuum and one leader) 40 ft of hose. You can add

quite a few lengths to it but at some point there will be two problems. One that the hoses will outweigh

the cleaner and two that the more hoses you add there more suction is lost to the head. Max lengths of

hose you can add depends on the suction of the system. The 4 Wheel has a cam that has only three cut

outs so that the unit goes straight longer in order to cover a larger pool.

What happens if you use the wrong cleaner in the wrong pool? If say you place a 4 Wheel unit into a

small pool( like a swim spa ) the 4 Wheel will never have enough leverage to climb the walls so it will go

to a wall and stay there with the wheels turning until the steering finally comes in and pulls it away. If

you place a 2 Wheel into a huge pool and you add a whole bunch of hoses to compensate the cleaner

will not cover the whole pool, it will favour either the shallow end or the deep‐end.

SOLUTION: Often if they have a 2 Wheel but need more straight run you can replace the 2 Wheel Cam

(896584000‐235) with a 4 Wheel Cam (896584000‐242). You can make that 2 Wheel go straight longer

but you cant really add weight so if they have added a whole bunch of hoses it won’t have enough

power even with a 4 Wheel Cam.


3

Cleaner function CHECK

To check the function of the cleaner you can take it with the sticker facing away from you. Turn the right

front wheel forward. This action tells you many things. Whether there is an obstruction, if something is

worn or broken.

If the unit has something stuck in it you will not be able to turn the right front wheel forward. It will be

stuck. If you can turn it but it ratchets then something is worn or broken. Possible parts that need to be

inspected are the wheel hub (896584000‐051) gear shaft into the wheel hubs ( right drive 896584000‐

112 and steering slide 896584000‐136), large drive gear 896584000‐457. If the right wheel spins freely

the wheel hub (896584000‐051) is super‐duper worn! If the right wheel is stuck then there is an

obstruction that needs to be cleared. See above figure for details.

Note: One should never turn the left front because depending on where it is in the cycle on the cam, the

left wheel will either turn (forward cycle steering slide is on the outside diameter of the cam), ratchet

(backward cycle and steering slide is in one of the cut outs of the cam) or spin freely (limbo and the

steering slide is between forward and backward motion).


4

THE POOLCLEANER DOES NOT MOVE

Possible Cause

Solution

Cleaner moving too slow Check Wheel RPM

The pump may be turned off or on low speed. Make sure the pump is ON.

The three way valve may be in the wrong position. If you have a designated suction port, divert suction away from your skimmers or main‐drains to the suction port. If you are using the skimmer divert suction away from the main‐drain to the skimmer.

The system may be dirty. The filter may be dirty, and or the skimmer baskets over packed with debris.

The pump may not be primed Make sure the pump is primed.

You may have a suction leak. Check for leaks in the system. (Bubbles in the returning water). Fix the leak. Usually O‐ring on pump lid, water level too low or plumbing leak (use shaving cream trick).

There could be a problem or obstruction somewhere in the system.

Clean and backwash the filter, clean the pump basket, make sure the vacuum hose is free from debris and leaks, check if pump impeller is blocked (see pump manual (impeller blockage is common in areas with pine needles).

Obstruction in the PoolCleaner itself.

To determine if there is an obstruction, take the cleaner out of the pool hold it in your hand with the sticker facing AWAY from you now turn the right front wheel forward (right is where your right hand is). If the cleaner moves smoothly, you don't have an obstruction (check the system its not the cleaner). If it wont move you will have to clear the obstruction

Turbine vanes in the wrong direction. Make sure the turbine vanes are in the right direction. See Below.


5

THE POOLCLEANER MOVES TOO SLOW (less than 11 RPM)

Possible Cause

Solution

There could be a problem or obstruction somewhere in the system.

Clean and backwash the filter, clean the pump basket, make sure the vacuum hose is free from debris and leaks, check if pump impeller is blocked (see pump manual).

Low wheel RPM (insufficient flow) (See the manual to adjust RPM) After adjusting, if it is still below 7 RPM your pump is not strong enough (the PoolCleaner™ will still move and clean but wont go up the wall). At such low flow most other cleaners won’t work at all. Designated line may be blocked have them hook to skimmer line to see if there is a difference in RPMs.

Obstruction in the PoolCleaner itself. Clear the obstruction. Click here to see how.

See also the solutions for the cleaner "does not move" above.

THE RIGHT WHEEL WILL NOT TURN WHEN ROTATED BY HAND

Possible Cause

Solution

There could be a problem or obstruction in the PoolCleaner.

Either in the turbine vanes or the gearing. Clear the obstruction. (there could be something in the turbine chamber or something stuck in the wheel hub)

Turbine vanes could be worn. Replace turbine vanes.

THE RIGHT WHEEL SKIPS WHEN ROTATED BY HAND

Possible Cause

Solution

There is a problem in the PoolCleaner. Wheel hub (896584000‐051)and or right drive gear (896584000‐112)worn or damaged


6

THE LOOPS IN THE HOSES WONT COME OUT

Possible Cause

Solution

The hoses must have been stored in a coiled position.

Lay them straight in the sunlight. If that doesn't work, replace that section of hose. Next time store them straight! You can get a PoolCleaner Keeper to solve this problem.

Dirt in the swivel cone. (Swivel on the head of the cleaner).

Although the swivel is self‐cleaning there may be excessive debris. Remove any debris. It is helpful to place the swivel under a running tap while twisting to clean.

Leaf Canister in wrong place. If using a leaf canister it may be in the wrong place or not floating.

Leader hose is kinked. If the cleaner was put on the deck with the hoses attached to it, then the leader hose may have a kink in it.

THE POOLCLEANER TURNS IN CIRCLES, IT WONT GO STRAIGHT AT ALL.

Possible Cause

Solution

There is a problem in the PoolCleaner. Wheel hub (896584000‐051)and or large drive gear (896584000‐457) and or steering slide (896584000‐136) and or right drive gear (896584000‐112)worn or damaged

THE POOLCLEANER DOES NOT CLEAN THE ENTIRE POOL.

Possible Cause

Solution

The vacuum hose is too short. The hoses must be one to two lengths longer than the farthest point from attachment.(See manual)

The float may be in the wrong position. The Float(s) should be 22‐24” (60 cm) from the gray cuff ( head of the cleaner) (See manual)

The hose cone swivel may be blocked. Although the swivel is self‐cleaning there may be excessive debris. Remove any debris. It is helpful to place the swivel under a running tap while twisting to clean.

Returns pushing cleaner. Pool return fittings may be pushing the


7

PoolCleaner hoses away. Make sure return fittings are pointed DOWN. (See manual)

The vacuum hose is too short. The hoses must be one to two lengths longer than the farthest point from attachment.(See manual)

THE POOLCLEANER WONT CLIMB THE WALL.

Possible Cause

Solution

See “moves too slow” and “doesn’t clean entire pool” (See above)

The float position may need to be adjusted. For the most part make sure the Float is 24” (60 cm) away from gray cuff (See manual). But it may be necessary to adjust it by twisting the Float away from the gray cuff to improve climbing. Other factors may be at work like water too shallow, return fittings not pointed down, hoses too short.

Pool surface too slick. If the pool surface is say tile or spray on fiberglass then you will need tile tires as the normal ones may slip.

Not enough Suction. Too little suction or flow. Increase the RPMS

Note: It is NOT imperative for a cleaner to go up the wall as there is no dirt or very little dirt on the walls.

WHEELS ARE WOBBLY

Possible Cause

Solution

Wheel hub bushing is worn. DO NOT OVER TIGHTEN. It is a shoulder bolt! Wheel hubs are worn please replace.

PUMP TURNS OFF AND CLEANER POPS OUT OF SKIMMER OR SUCTION INLET (another symptom is

cleaner is floating)

Possible Cause

Solution

Air in System. Air in system. When the pump shuts off the air goes the path of least resistance and pops out the hose. Fix the air leak. Usually O‐ring on pump lid, plumbing leak (use shaving cream trick).


8

THE POOLCLEANER CLIMBS THE WALL TOO MUCH OR IT CLIMBS OUT.

Possible Cause

Solution

Too much suction (flow). Decrease the suction to the cleaner. Lower the RPMS

Tires may be worn. The tire treads may be worn and/or the skirts may be worn, hence increasing the suction under the machine. See below for how to check tire wear.

Need to regulate flow. May need a bypass valve or need to adjust auto skim plate.

THE POOLCLEANER FALLS ON ITS SIDE AND TAKES TOO LONG TO RECOVER.

Possible Cause

Solution

The vacuum hose is too short. The hoses must be one to two lengths longer than the farthest point from attachment. (See manual)

The float may be in the wrong position. Adjust float to be 24” (60 cm) from the gray cuff.

Return fittings pushing cleaner. Return fittings are not pointed down. Point them down.

Unit doesn’t have enough suction. Check Wheel RPM and adjust accordingly.

TURBINE VANES/BLADES POP OUT OF TURBINE

Possible Cause

Solution

Vanes in the wrong way. Wrong side of vane in the turbine hub. Large elliptical side should be in turbine.

Turbine Hub worn Replace turbine .

ALWAYS TURN OFF THE SYSTEM BEFORE PERFORMING ANY REPAIRS.

PROBLEM SOLUTION

The PoolCleaner does not move.

The PoolCleaner moves too slow.

The right wheel will not turn when rotated by hand.

The right wheel skips teeth when rotatedforward by hand.

The loops in the hoses won’t come out.

The PoolCleaner turns in circles, itwont go straight at all.

The PoolCleaner does not clean the entire pool.

The PoolCleaner climbs the wall toomuch or climbs out.

The PoolCleaner won’t climb the wall.

When the pump turns off the hoses popout of the skimmer or suction inlet.

Check wheel RPM.Obstruction in the PoolCleaner itself. If there was an obstruction make sure vanes are replaced correctlyThe pump may be turned off or on low speed.The pump may not be primed. Check for leaks in thesystem (symptoms--bubbles from the returns ?) Possible otherproblem or obstruction in the system. Pump impeller blocked? Filter needs backwashing. Clean pump basket, skimmers.Turbine vanes/blades in wrong direction and/or wrong side.

Problem or obstruction in the system. Obstruction in the PoolCleaner itself.Low wheel RPM (insufficient flow).

Obstruction in the PoolCleaner itself.

(see also “does not move” above)

(looking from behind)

(looking from behind)

(see also “moves too slow” above)

Wheel hub or right drive gear worn/damaged.

The hoses have been stored in a coiled position. Lay them straight in the sunlight.Clean swivel on cleaner head by running it under a tap. If using a leafcanister it may be in wrong place or not floating.

Wheel hub and/or large drive gear and/or steering slideassembly and/or right drive gear are worn or damaged.

The hose is too short.The float(s) may be in the wrong position. Should be 22-24” from cleaner head.The Hose Cone Swivel (on the turbine cover) may be dirty. The return fittings may be pushing the PoolCleanerhoses away. Point them down.

The tire treads and skirts may be worn down.Too much suction or flow. You are not using the Bypass Valve (if hook up is in skimmer).Auto skim plate/vac plate needs adjustment.

Too little suction or flow.Float may be in the wrong position.

Wheels are wobbly. DO NOT OVER TIGHTEN. Wheel hubs are worn please replace.

The PoolCleaner falls on its sideand takes too long to recover.

The float(s) may be in the wrong position or missing. The hose is too short. The return fittings may be pushing the PoolCleaner hoses away. Check wheel RPM.

Turbine vanes /blades pop out ofturbine.

Wrong side of vane in the turbine hub. Large eliptical side should be in turbine.Turbine hub possibly worn.

Make sure hose cone is properly placed into inlet/port/watergate.Air in system. When pump shuts off air goes path of leastresistance and pops out the hose. Fix air leak.

TROU

BLESHO

OTIN

G YO

UR PO

OLCLEAN

ERTRO

UBLESH

OO

TING

YOU

R POO

LCLEANER

(another symptom of air is a cleaner floating )

POOLCLEANER OBSTRUCTION

TURBINE VANES/BLADES

RPMS

TIRES

1. Rotate the right front wheel forward (the grill is the front) . If it wont move there is an obstruction. 2. Remove the three screws that hold the Shroud ( Top Cover ). 3. Remove the Shroud. 4. Remove the turbine cover ( wiggle it up and off ).5. Visually inspect the cleaner. Remove any debris found in the turbine, reduction gears, wheel hubs etc.. If you removethe turbine vanes/blades please be sure to replace them correctly (see below). Replace the turbine cover and repeatstep one before placing the shroud back on, drop 3 screws into slots and secure.

TROU

BLESHO

OTIN

G YO

UR PO

OLCLEAN

ERTRO

UBLESH

OO

TING

YOU

R POO

LCLEANER

FRONT

FRONT

BACK

1 2 3 4 5

The turbine vanes have to be placed in the turbine hub a certain direction. We use the following mnemonic “ The turbine vanes are like a wave breaking on the grill”. In the front of the unit the vanes are convex ( like a mountain ) in the back they are concave ( like a valley ). NOTE: The large elliptical end of the vanes is placed into the turbine.

GRILL

round

larger elliptical

Count RPM here at the hump on the RIGHT FRONT WHEEL

While the POOLCLEANER™ is running take it by the leader hose so that the POOLCLEANER™ is just below the water. (KEEP THE CLEANER BELOW THE WATER LEVEL or else it will suck air). Now count the number of revolutions made per minute by the RIGHT FRONT WHEEL by using the hump (raised knob) as your marker. It should be between 11 and 14 RPM

The tires must be replaced when they are worn down to the tread wear indicators. Note: if you cant see them you are worn past them.

Please note: in order to replace back tires you will first have to remove the shroud, then remove the wheeland only then can you take the tires off the wheel hub.

RPM=revolutions per minute

R

L

FRONT

BACK

wear marks

www.thepoolcleaner.com Tel 707 566 0400

To Change the Turbine Hub of the PoolCleaner

1. Remove the two front wheels. 2. Remove shroud with Phillips (3 self tapping screws)

B

R L

F

3. Remove Upper body assembly. 4. Remove steering slide assembly with shaft and 2 springs (Front Left) The machine is marked R and L on side wall)

5.Remove ¼” S/S shaft from left to right 6. Remove turbine hub and replace with new turbine hub using a smaller shaft or Philips screw driver and vanes (Make sure vanes point forward!!!) (Smaller than ¼” otherwise the hole will be destroyed).

R L

7. Insert shaft from right to left, first 8. Insert steering slide assembly with through the turbine hub, then through two springs and shaft (Make sure it bottoms out the 2 gears and then through the cam and does NOT push the drive gear assembly out) all the way into the left side body. Flush (Bearing to be flush with outside of right lower with the outside of the left side. body). (Remove the elastic band)

R L

9. Place upper body assembly back on 10. CHECK THE FREE SPINNING AND lower body. FREE ROTATING OF GEARS, VANES AND DRIVE GEAR ASSEMBLY. By rotating Front drive gear shaft forward.

11. Replace the Shroud with 3 screws 12. Replace the 2 wheel assemblies. Make sure

the shoulder bolt is hand tight. CHECK THE FREE SPINNING AND FREE ROTATING OF GEARS, VANES AND DRIVE GEAR ASSEMBLY BY ROTATING THE RIGHT FRONT WHEEL FORWARD.

2 Wheel PoolCleaner 896584000-013

Item Key Description Cleaners that use it MFG # / SKU

1 Top Shroud Screw Kit (3 Screws per Kit) 2X/4X/2XLE/4XLE 896584000-2042 Top Shroud Kit (shroud + 3 screws) 2X/4X 896584000-1813 Upper Body Assemb (turbine cover) 2X/4X 896584000-0684 Turbine Vane Kit (6 per kit) suction 2X/4X/2XLE/4XLE 896584000-1675 Wheel Hub Assemb 2X/4X/PC 896584000-051

6a. Front Tires with Super Humps Blue(2 per kit) for concrete 2X/4X/PC 896584000-1436b. Front Tires with Hump Blue (2 per kit) for vinyl and fiberglass 2X/4X/PC 896584000-0756c. Solid Front Tires Blue (2 per kit) for Tile pools 2X/4X/PC 896584000-334

6d.Front Tires with Super Super Humps Blue(2 per kit) for BIG obstacles 2X/4X/PC 896584000-679

7 Wheel Bolt Kit (2 per kit) 2X/4X/2XLE/4XLE/PC 896584000-1988 Steering Slide Assembly 2X/4X/2XLE/4XLE/PC 896584000-1369 Turbine Hub and Vane Kit (hub + 6 vanes) 2X/4X/2XLE/4XLE 896584000-36510 Large Drive Gear 2X/4X/2XLE/4XLE/PC 896584000-45711 Front Right Drive Gear Assemb 2X/4X/2XLE/4XLE/PC 896584000-11212 Bracket for Skirts (4 per kit) 2X/4X 896584000-41913 Front Skirts with Rollers (4 per kit) 2X/4X 896584000-25914 Skirt Kit A (4 per kit) for back of 2 wheel 2X 896584000-09915 Small Drive Gear 2X/4X/2XLE/4XLE/PC 896584000-46416 2X Steering Cam 2X 896584000-23517 Reduction Gear 2X/4X/2XLE/4XLE/PC 896584000-47118 Bypass Valve Replacement Kit (Valve + Hose Cone) 2X/4X 896584000-95219 Hose Cone 2X/4X 896584000-17220 Water Gate (Suction Port Door) White 2X/4X 896584000-48821 2 Wheel Tune Up Kit (2 tires, 6 vanes, 4/4 skirts) 2X 896584000-42622 Leader Hose 2X/4X 896584000-21123 Vacuum Hose 2X/4X 896584000-22824 2X Hose Pack (9 vacuum hose + 1 leader hose) 2X 896584000-38925 2 Wheel Lower Body 2X 896584000-79226 Universal PoolCleaner Float 2X/4X/PC 896584000-28027 PoolCleaner Keeper 2X/4X/PC 896584000-501

First Generation (older)

143

143051

051

198 198

204

181

068167

365

952

172

488 471

235

792

464

112 457 136

426

280 259419 099

211 228

501389

NEXT GEN

143

143051B

051B

204

181

068167

365

952

172

488

471

235

792B

464

112 457 136

426

280 259419 099

211 228

501389

976 976

on back of shroud handle

983

990

983

2 Wheel PoolCleaner NEXT GEN 896584000-013


1 Top Shroud Screw Kit (3 Screws per Kit) 2X/4X/2XLE/4XLE 896584000-2042 Top Shroud Kit (shroud + 3 screws) 2X/4X 896584000-1813 Upper Body Assemb (turbine cover) 2X/4X 896584000-0684 Turbine Vane Kit (6 per kit) suction 2X/4X/2XLE/4XLE 896584000-1675 Wheel Hub Assemb 2X/4X/PC 896584000-051B

6a.Front Tires with Super Humps Blue(2 per kit) for concrete 2X/4X/PC 896584000-143

6b.Front Tires with Hump Blue (2 per kit) for vinyl and fiberglass 2X/4X/PC 896584000-075

6c. Solid Front Tires Blue (2 per kit) for Tile pools 2X/4X/PC 896584000-334


7 Wheel Bearing 2X/4X/2XLE/4XLE/PC 896584000-9768 Steering Slide Assembly 2X/4X/2XLE/4XLE/PC 896584000-1369 Turbine Hub and Vane Kit (hub + 6 vanes) 2X/4X/2XLE/4XLE 896584000-36510 Large Drive Gear 2X/4X/2XLE/4XLE/PC 896584000-45711 Front Right Drive Gear Assemb 2X/4X/2XLE/4XLE/PC 896584000-11212 Bracket for Skirts (4 per kit) 2X/4X 896584000-41913 Front Skirts with Rollers (4 per kit) 2X/4X 896584000-25914 Skirt Kit A (4 per kit) for back of 2 wheel 2X 896584000-09915 Small Drive Gear 2X/4X/2XLE/4XLE/PC 896584000-46416 2X Steering Cam 2X 896584000-23517 Reduction Gear 2X/4X/2XLE/4XLE/PC 896584000-471

18Bypass Valve Replacement Kit (Valve + Hose Cone) 2X/4X 896584000-952

19 Hose Cone 2X/4X 896584000-17220 Water Gate (Suction Port Door) White 2X/4X 896584000-48821 2 Wheel Tune Up Kit (2 tires, 6 vanes, 4/4 skirts) 2X 896584000-42622 Leader Hose 2X/4X 896584000-21123 Vacuum Hose 2X/4X 896584000-22824 2X Hose Pack (9 vacuum hose + 1 leader hose) 2X 896584000-38925 2 Wheel Lower Body NEXT GEN 2X 896584000-792B26 Universal PoolCleaner Float 2X/4X/PC 896584000-28027 PoolCleaner Keeper 2X/4X/PC 896584000-50128 Wheel Clip 2X/4X/PC 896584000-98329 Suction inlet 2X/4X 896584000-990

952

172

204

181 280

082143

167488 068

365471

464

143

808051

198

129

242

198

457 136

259 419105

051

211 228

112

501

First Generation (older)4 Wheel PoolCleaner 896584000-020


1 Top Shroud Screw Kit (3 Screws per Kit) 2X/4X/2XLE/4XLE 896584000-2042 Top Shroud Kit (shroud + 3 screws) 2X/4X 896584000-1813 Upper Body Assemb (turbine cover) 2X/4X 896584000-0684 Turbine Vane Kit (6 per kit) suction 2X/4X/2XLE/4XLE 896584000-1675 Wheel Hub Assemb 2X/4X/PC 896584000-051





7 Wheel Bolt Kit (2 per kit) 2X/4X/2XLE/4XLE/PC 896584000-1988 Steering Slide Assembly 2X/4X/2XLE/4XLE/PC 896584000-1369 Turbine Hub and Vane Kit (hub + 6 vanes) 2X/4X/2XLE/4XLE 896584000-36510 Large Drive Gear 2X/4X/2XLE/4XLE/PC 896584000-45711 Front Right Drive Gear Assemb 2X/4X/2XLE/4XLE/PC 896584000-11212 Bracket for Skirts (4 per kit) 2X/4X 896584000-41913 Front Skirts with Rollers (4 per kit) 2X/4X 896584000-25914 Skirt Kit B (4 per kit (2+2)) for back of 4 wheel 4X 896584000-10515 Small Drive Gear 2X/4X/2XLE/4XLE/PC 896584000-46416 4X Steering Cam 4X 896584000-24217 Reduction Gear 2X/4X/2XLE/4XLE/PC 896584000-47118 Bypass Valve Replacement Kit (Valve + Hose Cone) 2X/4X 896584000-95219 Hose Cone 2X/4X 896584000-17220 Water Gate (Suction Port Door) White 2X/4X 896584000-488

21a. Back TiresBlue (2 per kit) No Hump 4X/XP 896584000-082

21b.Solid Back Tires Blue (2 per kit) for Tile pools No Hump 4X/XP 896584000-372

22 Leader Hose 2X/4X 896584000-21123 Vacuum Hose 2X/4X 896584000-22824 4X Hose Pack (10 vacuum hose + 1 leader hose) 4X 896584000-39625 4 Wheel Lower Body 4X 896584000-80826 Rear Wheel Bearing and Shaft Kit 4X/PC 896584000-12927 Universal PoolCleaner Float 2X/4X/PC 896584000-28028 PoolCleaner Keeper 2X/4X/PC 896584000-501

952

172

204

181 280

082

167

488

068

365471

464129

242

457 136

259 419105

211 228

112

501

143

051B

808B976

983

143

051B

976983

on back of shroud handle

NEXT GEN 4 Wheel PoolCleaner 896584000-020


1 Top Shroud Screw Kit (3 Screws per Kit) 2X/4X/2XLE/4XLE 896584000-2042 Top Shroud Kit (shroud + 3 screws) 2X/4X 896584000-1813 Upper Body Assemb (turbine cover) 2X/4X 896584000-0684 Turbine Vane Kit (6 per kit) suction 2X/4X/2XLE/4XLE 896584000-1675 Wheel Hub Assemb 2X/4X/PC 896584000-051B





7 Wheel Bearing 2X/4X/2XLE/4XLE/PC896584000-9768 Steering Slide Assembly 2X/4X/2XLE/4XLE/PC 896584000-1369 Turbine Hub and Vane Kit (hub + 6 vanes) 2X/4X/2XLE/4XLE 896584000-36510 Large Drive Gear 2X/4X/2XLE/4XLE/PC 896584000-45711 Front Right Drive Gear Assemb 2X/4X/2XLE/4XLE/PC 896584000-11212 Bracket for Skirts (4 per kit) 2X/4X 896584000-41913 Front Skirts with Rollers (4 per kit) 2X/4X 896584000-25914 Skirt Kit B (4 per kit (2+2)) for back of 4 wheel 4X 896584000-10515 Small Drive Gear 2X/4X/2XLE/4XLE/PC 896584000-46416 4X Steering Cam 4X 896584000-24217 Reduction Gear 2X/4X/2XLE/4XLE/PC 896584000-47118 Bypass Valve Replacement Kit (Valve + Hose Cone) 2X/4X 896584000-95219 Hose Cone 2X/4X 896584000-17220 Water Gate (Suction Port Door) White 2X/4X 896584000-488

21a. Back TiresBlue (2 per kit) No Hump 4X/XP 896584000-082

21b.Solid Back Tires Blue (2 per kit) for Tile pools No Hump 4X/XP 896584000-372

22 Leader Hose 2X/4X 896584000-21123 Vacuum Hose 2X/4X 896584000-22824 4X Hose Pack (10 vacuum hose + 1 leader hose) 4X 896584000-39625 4 Wheel Lower Body 4X 896584000-808B26 Rear Wheel Bearing and Shaft Kit 4X/PC 896584000-12927 Universal PoolCleaner Float 2X/4X/PC 896584000-28028 PoolCleaner Keeper 2X/4X/PC 896584000-50129 Wheel Clip 2X/4X/PC 896584000-983

rpms - images-na.ssl-images- · pdf filethe rpms are so low that the friction from the floor...

Documents