rx200 s4 config

PRIMERGY RX200 S4System configurator and order-information guide

Contents

InstructionsConfiguration diagramConfigurator

0 System softwareI Basic unitIII ProcessorIII MemoryIV Riser CardV GraphicsVI Accessible drivesVII Hard disk drivesVIII SCSI controllerIX Fibre-Channel controllerX Disk arrayXI Communication/NetworkXII System Management Products (RemoteView)XIII MiscellaneousXIV Country specific power cord

Change report

PRIMERGY Server

January 2009

System configurator and order-information guidePRIMERGY RX200 S4 Status 2008-12-17

Instructions

This document contains basic product and configuration information that will enable you to configure your system viaPC-/SystemArchitect.

Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system.

You can configure your individual PRIMERGY server in order to adjust your specific requirements.

The System configurator is divided into several chapters that are identical to the current price list and PC-/SystemArchitect.

Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through the configurator by following the lines from the top to the bottom.

Section III Memory

There are X memory slots which can be equipped with XXX MB.It is permissible to make up to X passes through the memory upgrade options.

S26361-XXX-XXX S26361-XXX-XXXMemory XXX MB Memory XXX MB

X times

max. X times per system max. X times per system

In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x

Please note that there are information symbols which indicate necessary information.

Further information in the internet see:

http://www.primergy.com (internet)

http://extranet.fujitsu-siemens.com/primergy (extranet)

Prices and availability see price list and PC-/SystemArchitect.Subject to change and errors excepted.

Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 2 of 20


Configuration diagram PRIMERGY RX200 S4

System unit ( I )

board front side

Branch 0 ( Channel A + B ) right

Bank 1 (2 Moduls)Bank 2 (2 Moduls)Bank 3 (2 Moduls) Air channel

Branch 1 ( Channel C + D ) Bay for 3,5"x 0,5" LocalView / CSS

Bank 1 (2 Moduls) Bay for 5,25"x 0,5" SATA-DVD Bank 2 (2 Moduls) Processor ( II )Bank 3 (2 Moduls) Xeon Dual-or Quad Core

CPU with 1066 or 1333 MHz Accessible drives ( V )Frontsidebus

Hard disk drives ( VI )rear side left side

1. PSU 2. PSU Double Fan3.5"x1" SAS or SATA

Redundant

power supply Redundant Fansoption

3.5"x1" SAS or SATA

RAID 1(E) supporton-board

left side

Extension slots for

SCSI Controller ( VIII ) 2.5"x1" SAS Disk Array ( X )Communication/Network ( XI )System Management ( XII )Miscellaneous ( X ) 2.5"x1" SAS

Slot 0: PCIe x4 ( internal only ) 2.5"x1" SAS For modular RAID-controller

Slot 1: PCIe x8 (low profile, half length) 2.5"x1" SAS ( 174mm incl. bracket )

Slot 2: PCIe x8 (1x standard hight, half length) ( 174mm incl. bracket )

Key:

Included in basic unit Option

One CPU ( first CPU ) and one memory ( first memory ) has to be selected for an orderable basic unit.

Xeon Dual-or Quad Core CPU incl. Heatsink

Xeon Dual-or Quad Core CPU incl. Heatsink

3.5"

HD

D b

ays

optio

n2.

5" H

DD

bay

s op

tion

riser

con

nect

or

Fujitsu Siemens ComputersEnterprise Products PRIMERGY Server 3 of 20

System configurator and order-information guideStart PRIMERGY RX200 S4 PRIMERGY RX200 S4 Status 2008-12-17

SW Configurator 32 bit

with OEM-Software without OEM-Software for PRIMERGY Server for PRIMERGY Server

OEM-SW is bound to HW andVMware-Software is not allowed to be ordered- VCMS VirtualCenter Management Server separately.- Virtual Infrastructure 3 Exception: VMware SW

For all SW products please refer to the corresponding software configurator accessible viathe Extranet under Configuration & Tools, -All configurations, -Software, URL see below.

Microsoft - Software: W **) PRIMECLUSTER *) - Windows Server 2003 R2, - Clustering Standard Edition - Load Balancing Enterprise Edition

! Web Edition, SP2/English - Additional loose Linux - Software **) Client-Access-Licenses (CALs) - Open Enterprise Server ***) (not for Web Edition) - SuSe Linux ES (OEM)

- SuSe Linux ES (support)- Red Hat EL (OEM): LO- Red Hat EL (Support): LS

DuplexDataManager & MultiPathW2K3; Linux (RedHat 4 / SLES 9)

Manageability Software: V**)- IRMC advanced Pack- RemoteDeploy- RemoteView SW Details eg. version numbers are published- Altiris Server Deployment in the separate SW-Configurator

*) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet underBackup-Software / http://extranet.fujitsu-siemens.com/primeclusterApplication-Software: U- ARCserve **) Pay attention to release and order information in PRINCE -> Operating System- openSM2 http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm

***) Supply over distribution or procurement from FSC VP BC Software

They find single software configurators and release lists (OS-matrix / system management / security) under following addresses:

for internal users: http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htmfor partners: http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm

Continue with PRIMERGYHW configurator



SW Configurator EM64T

with OEM-Software without OEM-Software for PRIMERGY Server for PRIMERGY Server

OEM-SW is bound to HW andVMware-Software is not allowed to be ordered- VCMS VirtualCenter Management Server separately.- Virtual Infrastructure 3 Exception: VMware SW

For all SW products please refer to the correspondingsoftware configurator accessible via the Extranet under"Configuration & Tools, -All configurations, -Software,URL see below.

Microsoft - Software: W Linux - Software *) **)

only - Windows Server 2003 R2, only - SuSe Linux ES (OEM)EM64T Standard x64 Edition EM64T - SuSe Linux ES (support)

Enterprise x64 Edition - Red Hat EL (OEM): LO - Additional loose - Red Hat EL (Support): LS Client-Access-Lizenzen (CALs)

only MultiPath, Duplex Data EM64T Manager (DDM)

Windows, Linux (W-DDM)

Details eg. version numbers are published Manageability Software: V**) in the separate SW-Configurator

only - RemoteDeployEM64T - RemoteView SW

- IRMC advanced Pack *) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet underhttp://extranet.fujitsu-siemens.com/primecluster

**) Pay attention to release and order information in PRINCE -> Operating System

You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:

for internal users: http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htmfor partners: http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm

Continue with PRIMERGYHW configurator

http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm



Section I Basic unit

System unit consisting of:* 1U Housing including

- hot plug Power supply unit with 1 PSU module and power cord rack 4m lenght (can be upgraded with one additional PSU module)

* Fans - Redundant and hot plug system fans (6x)

* Drives / Bays - 1 bay for 4x 2.5" SAS HDD or 2x 3.5" SAS / SATA HDD option - 1 bay SATA DVD-ROM 0,5" height (option) - 1 bay 0,5" height for optional CSS-modul ( Customer Self Service ) or LocalView

* Integrated ServerView Diagnostics Technology for indication of internal failed components Options:

* 2nd hot plug power supply module 650W (PSU) for redundancy* Two optional Rackmount kits RMK-F1_RX100-200-300 ( full extraction ) or RMK-ST_RX100-200 ( partial extraction with lower cost )

* 2x 3.5" HD backplane kit* 4x 2.5" HD backplane kit

* - Optional modular RAID 0/1/1e controller with IME (Integrated Mirroring Enhanced) support based on LSI 1064 chipset or as alternative - optional modular RAID 5 controller based on LSI 1078 chipset ( only for 2.5" HD`s )

* One 0,5" bay can be configured with an optional LC- display for LocalView in a drawer or with an optional CSS ( Customer Self Service ) modul for indication of a failed component via LED`s Simultaneously components are marked which can be replaced by the customer. This LEDs can be dispalyed during service even without mains connection. Systemboard D2671 with:* Xeon Dual- or Quad-Core CPU, supporting 64Bit EM64T and Intel VT / HT / DBS Technology. ( VT =Virtualisation Technology, HT = Hyper Threading, DBS = Demand Based Switching ) First CPU has to be selected for an orderable basic unit,* Chipset Intel 5000P (codenamed Blackford) * 3 PCIe slots

-1x PCIe x8 (standard and Low Profile cards) and 1x PCIe x8 (Low Profile cards only) -1x PCIe x4 internal for modular RAID controller only

* 12 memory slots for max. 48GB RAM ( Fully Buffered DIMM = FBD667 / PC2-5300F ) available - Memory is divided into two branches, driven by a memory controller each. - Each branch has 2 channels with 3 DIMM slots each (bank 1 and bank 2) - Max. 4GB modules per slot are possible First Memory ( two modules ) has to be selected for an orderable basic unit - Memory upgrade is possible per branch with modul pairs ( one pair / branch ) - Memory mirrroring is supported branch to branch for 2 identical module pairs each in the same same memory bank of branch 0 and branch 1 - Max. memory bandwidth and 4-way interleaving is supported with 2 identical memory pairs in one memory bank (one pair per branch) if mirroring is disabled - SDDC (Chipkill) is supported for memory modules,

* 2-port SATA controller on-board included in chipset ESB2-T for SATA Raid0/1 ( for 2x 3.5" HD`s only !! )* One SATA cport on-board for 1x DVD integrated in the Intel Southbridge ESB2-T

* 2x 1Gbit Ethernet LAN BroadCom 5708 with TOE support on-board* iRMC S2 (integrated Remote Management Controller) on-board server management controller with dedicated 10/100 Service LAN-port and integrated graphics controller. The Service LAN-port can be switched alternatively on standard Gbit LAN port 1

* Graphics Controller integrated in iRMC S2 (integrated Remote Management Controller): 1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 640x480x32bpp 85Hz (1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off)

A


System configurator and order-information guideA PRIMERGY RX200 S4 Status 2008-12-17

Interfaces at the rear:* 1x RS-232-C (serial, 9 pins) (usable for BMC or OS or shared)* 1x keyboard (PS/2)* 1x mouse (PS/2)* 1x VGA (15 pins)* 2x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup* 2x LAN RJ45, 1x Service-LAN RJ45

Interfaces on the front:* 2x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup

Interfaces internal:* 1x USB 2.0 ( UHCI ) with 480MBit/s for dongle funcionality, no USB wakeup

Cables:1. SATA cable for DVD.2. SAS cables for up to 4 internal hot plug HDDs3. Power cableSoftware: - ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates - Documentation engl. (multilingual on CD)

Mounting kits for PRIMERGY RX200 S4 - 1 pair of telescopic rails either full or partial extraction

with partial extraction server can not be fully pulled out, but lower cost version of RMK - 1 Vario carrier DC-PC-3rd party Rack

allows toolless adjustable in depth and easy mountingMounting kit for mounting of servers in FSC 19" PRIMECENTER- racks and all server racks conforming to EIA standard EIA-310-D for 19" racks. Therefore the mounting kit is variable in depth from 704-790mm

Cables included in basic unit

Connections Cable PRIMERGY RX200 S4 Key: SAS

1. SATA DVD SATA

2. SAS cables HDDs

3. Power cable

B


System configurator and order-information guideB PRIMERGY RX200 S4 Status 2008-12-17

Base unit without CPU and Memory S26361-K1167-V101Rack version for 19'' racks with1 hot plug power supply moduleNo Rack-mounting kit includedFor an orderable basic unit one CPU = first CPU,one memory = first memory as well as one of two possible rack-mount kit options has to be selected

S26113-F527-E12nd redundant PSU module For later conversion the following kit is available:for redundancy 1.) 1 power supply module hot plug S26113-F527-L1uses hot plug PSU slot incl. power cordmax. 1x per system

S26361-F2735-E101 S26361-F2735-E110 S26361-F2735-E111 RMK-F1_1-2U Server RMK-P_1-2U Server No Rackmount-Kit optiontelescopic rail, full extraction, telescopic rail, partial extraction Only for loose deliveries1-hand-mounting lower costs option No mounting in Racks possibleconsisting of consisting of max. 1x per system

- 1 pair of telescopic rails - 1 pair of telescopic rails

with easy-mounting-clips with partial extraction

- 1 bracket DC-PC-3rd-Rack - 1 bracket DC-PC-3rd-Rack1x per system 1x per system

S26361-F2735-E8 CCabel arm for 1U Server

- for FSC Primecenter / S26361-F2735-L101

Datacenter Racks S26361-F2735-L110

- for 3rd Party racks RMK_1U Server

1x per system for loose delivery

partial extraction is lower cost

version of RMK. Server could not

completly pulled out of the Rack

PRIMERGY PRIMECENTER-rack In case nor cable arm is ordered,Server must be prevent of beeing

pulled out.S26361-F1647-E302Installation ex works for one S26361-F2735-L8server or subsystem. Cabel arm for 1U ServerHereby the rack will be delivered for loose deliverycompletely pre-mounted andall wired connections are tested. S26361-F2735-L7With racks 12U, 24U, 38U: Cable management PC-RackSystems and components - for FSC Primecenterwill be delivered installed in the rack - one additional U is neededWith racks 46U: for cable routing at the sideSystems and componentswill be delivered separately PRIMERGY 42/23U rackTo be ordered only together with PRIMERGY Classic 19" rack is not supporteda PRIMERGY PRIMECENTER rack e.g.: "Rack-mounting ex factory"S26361-K826-V10x This service is to be ordered oncerefer configurator PC-Rack per installable server/storagemax. 1x per System subsystem, in order to get the

server/storage subsystemmounted into the PRIMERGY racks.

In case of the 46 U PRIMERGY Rack,this service has to be ordered,to get the mounting kits and the

cables installed.

C


System configurator and order-information guideC PRIMERGY RX200 S4 Status 2008-12-17

Section II Processor

There are 2 processor LGA771 sockets available.The first socket is always equipped with the first CPU It is also possible to upgrade a dual-processor system later on with a second CPU

A multi-processor operating system is required for a dual-processor system.

Max. two CPU`s can be selected per basic unitOne of following CPUs has to be selected as first CPUfor an orderable basic unitOptional second CPU has to be the same type like the first CPUDual-Core CPU`s- 1x 64-bit Intel Xeon DP (6MB shared SLC = Second Level Cache ) with 1066 or 1333MHz Frontside Bus and passive heat sink occupies socket for one CPUXeon DP E5205 (1.86GHz/6M/1066) / 65W S26361-F3881-E186Xeon DP X5260 (3.33GHz/6M/1333) / 80W S26361-F3881-E333Xeon DP X5270 (3.50GHz/6M/1333) / 80W S26361-F3881-E350Quad-Core CPU`s- 1x 64-bit Intel Xeon DP (2x6MB shared SLC = Second Level Cache ) with 1066 or 1333MHz Frontside Bus and passive heat sink occupies socket for one CPUXeon DP E5405 (2.00GHz/2x6M/1333) / 80W S26361-F3880-E200Xeon DP E5420 (2.50GHz/2x6M/1333) / 80W S26361-F3880-E250Xeon DP E5430 (2.66GHz/2x6M/1333) / 80W S26361-F3880-E266Xeon DP E5440 (2.83GHz/2x6M/1333) / 80W S26361-F3880-E283Xeon DP X5460 (3.16GHz/2x6M/1333) / 120W S26361-F3880-E316Xeon DP X5470 (3.33GHz/2x6M/1333) / 80W S26361-F3880-E333Low Voltage Dual-Core CPU`s- 1x 64-bit Intel Xeon DP (4MB shared SLC = Second Level Cache ) with 1066 or 1333MHz Frontside Bus and passive heat sink occupies socket for one CPUXeon LV DP 5148 (2.33GHz/4M/1333) / 40W S26361-F3865-E433 while stocks lastLow Voltage Dual-Core CPU`s- 1x 64-bit Intel Xeon DP (6MB shared SLC = Second Level Cache ) with 1066 or 1333MHz Frontside Bus and passive heat sink occupies socket for one CPUXeon LV DP L5240 (3.00GHz/6M/1333) / 40W S26361-F3881-E500Low Voltage Quad-Core CPU`s- 1x 64-bit Intel Xeon DP (2x4MB shared SLC = Second Level Cache ) with 1066 or 1333MHz Frontside Bus and passive heat sink occupies socket for one CPUXeon LV DP L5310 (1.60GHz/2x4M/1066) / 50W S26361-F3866-E460Xeon LV DP L5410 (2.33GHz 2x6M/1333) / 50W S26361-F3880-E533Xeon LV DP L5420 (2.50GHz 2x6M/1333) / 50W S26361-F3880-E550Xeon LV DP L5430 (2.66GHz 2x6M/1333) / 50W S26361-F3880-E566

D


System configurator and order-information guideD PRIMERGY RX200 S4 Status 2008-12-17

Section III Memory

- There are 12 memory slots for max. 48GB RAM ( Fully Buffered DIMM = FBD667 / PC2-5300F ) available ( For explanation of following terms refer to section "Memory Configurations" - The memory area is divided into 2 branches with 2 channels each and 2 slots per channel - The first slot of each channel belongs to memory bank 1, the second slot belongs to memory bank 2 the third slot belongs to memory bank 3 - Each slot can optionally be equipped with 512MB, 1GB, 2GB or 4GB FBDIMM modules No mix of modules within one memory branch of bank1 or bank2 allowed. - Memory upgrade is only possible per branch with modul pairs ( one pair per branch, max. two pairs / branch).

- For each basic unit bank 1 of the first branch has to be equipped with one memory pair, (either 2x512MB = 1GB, 2x1GB = 2GB, 2x2GB = 4GB or 2x4GB = 8GB) Additional memory extensions can still be configured up to five times

- For the function Memory Mirroring two identical memory module pairs regarding capacity are necessary in each branch of one memory bank. So following memory has to be ordered: 1.) Minimum one time the same capacity like already is preinstalled in the basic unit has to be ordered 2.) For additional memory 2x the same capacity has to be ordered - Hotspare Memory is supported per branch if the branch is fully populated

- 4-way memory interleave technology for maximum performance is possible with 2 memory module pairs in one memory bank (one pair per branch ) - ECC with SDDC (Chipkill) is standard for RX200 S4.

For a description of memory configurations refer to section "Memory Configurations"

Minimum one Memory ( two modules ) = first Memory has to be selected for an orderable basic unit

S26361-F3263-E521 S26361-F3263-E722 S26361-F3263-E723 S26361-F3263-E724Memory 1GB Memory 2GB Memory 4GB Memory 8GBFBD667 / PC2-5300F FBD667 / PC2-5300F FBD667 / PC2-5300F FBD667 / PC2-5300F

6x consisting of consisting of consisting of consisting of 2 single rank modules 2 dual rank modules 2 dual rank modules 2 dual rank modulesoccupies one branch occupies one branch occupies one branch occupies one branchMax. 6x per system Max. 6x per system Max. 6x per system Max. 6x per system

E


System configurator and order-information guideE PRIMERGY RX200 S4 Status 2008-12-17

For the Memory Mirroring mode two identical memory modules pairs (branch 0 & 1) are necessary. ( bank1 of branch 0 and 1 contain identical memory pairs )

Therefore the following upgrade memory has to be ordered additionally: 1.) Minimum one time the same capacity like the selected first Memory of the basic unit = 2.) For addtitional memory 2x the same capacity =

The function Memory Mirroring can be configured per BIOS setup.For mirrored memory configurations the following items have to be considered:

Capacity: 50% of the configured memory Availability: Maximum memory availability

After non-correctable errors or too many correctable errors the Mirror takes over immediately and the system remains online.

Performance: 2-way interleave only in mirror configurations, therefore potentially not max. performance

- Function Hot Spare Memory. - If three banks of one branch are equipped with memory pairs, the third bank can be defined as hot spare memory bank. The capacity of the hot spare memory has to be equal or bigger than the capacity of the biggest capacity installed in the lower bank numbers.

The function Hot Spare Memory can be configured per BIOS setup. For Hot Spare Memory configurations the following items have to be considered:

Capacity: 2/3 of the configured memory if the third bank is the hot spare bankand each bank is equipped with the same modul capacity.

Availability: Less memory availability. Correction of single bit memory errors posssible.After non-correctable errors / too many correctable errors the system shuts down and during next reboot faulty memory becomes disabled.

Performance: 4-way interleave possible in max. spare mode configuration with two memory pairs per memory bank.4-way interleave increases system performance to maximum

In general it is recommended to use identical capacities over the branches of bank 1 to bank 3

to ensure max. performance bandwidth. = = =

bank 3

bank 2

bank 1First

Memory

Section IV Graphics

Graphics Controller integrated in iRMC S2 (integrated Remote Management Controller):1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 640x480x32bpp 85Hz(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off)

F

Memory Controllers

FB-DIMM FB-DIMM FB-DIMM FB-DIMM


channel 0 channel 1 channel 0 channel 1

branch 0 branch 1



System configurator and order-information guideF PRIMERGY RX200 S4 Status 2008-12-17

Section V Accessible drives

Setup RX200 S4 by ServerStart is supported with following configurations:no Floppy, no DVD, no CD:

remote installation only ( PXE service & DHCP server required)built in CD/DVD or USB CD/DVD, no Floppy disk drive:

UNC Network share reachable or USB Floppy connectedUSB Floppy, no CD/DVD:

USB CD/DVD connected

If installation is done locally, make sure you have internalor external FDD available for driver installation.

Following USB Components are available1) USB DVD+-RW: S26391-F7119-L100 Super Multi DVD slim drive (USB cable included)2) FDD USB (external): S26391-F264-L226

external USB FDD (USB cable included)3) USB Keyboard: S26381-K340-V120

KBPC PX D, professional keyboard4) USB Mouse: S26381-K415-L100

Optical Wheel Mouse Tilt USB/PS25) USB Memorybird: Memorybird 2GB S26391-F6047-L102

S26361-F3268-E1 S26361-F3269-E1 S26361-F3531-E1CD-RW / DVD slim SATA DVD-RW supermulti slim SATA Blu-ray Combo slim SATA

1x 24x CD-R/RW/ROM 8x DVD all formats, DUAL/DL, DVD-RAM 6x BD-ROM, 16x DVD, 40x CDCD-RW only with W2K, W3K, Linux only W2K, W3K and Linux BD DL and all CD/DVD formats0.5 x 5.25", anthracite bezel 0.5 x 5.25", anthracite bezel 0.5 x 5.25", anthracite bezelmax. 1x per system max. 1x per system max. 1x per system

G HModular Disk Array + 3.5" HD`s Modular Disk Array + 2.5" HD`s


System configurator and order-information guideG PRIMERGY RX200 S4 Status 2008-12-17

Section G-VI Drive Bay for 3.5" HD Basic Unit

2x 3.5" HDD OptionDrive Bay with up to 2x 3.5" slots

Section G-VII Modular Raid 0/1, Raid5 and on-board Controller for 3.5" HD`s

S26361-F3257-E44 port SAS RAID Controller Modular Raid 0/1 controller with IME support for SAS-HDsLSI IME (Integrated Mirroring Enhanced) offers the RAID levels 0, 1, 1E MegaRAID SAS 1064 IME is a RAID 0, 1 implementation, whereby RAID 1 can operate no Cache, no BBU an odd number of hard disks. Up to 4 hard disks including one hot spare HD RAID 0, 1 & 1E are possible (limited by HHD slots in system). SAS 3Gb/sec Windows 2003 as well as SUSE and RedHat Linux are supported 4 internal ports The SAS IME solution supports 2 independent RAID volumes.PCIe x4, 160mm There is no support of any external storage by this RAID solution. max. 1x per system

Modular Raid 5 controller for SAS/SATA-HDs1x RAID levels 0, 1, 10, 5, 50, 6 and 60 are supported

There is no support of any external storage by this RAID solution.

S26361-F3257-E256 S26361-F3257-E512 on-board 2-port 8 port SAS RAID Controller 8 port SAS RAID Controller SATA Raid 0/1 controllerLSI LSI included in chipset ESB2-TMegaRAID SAS 1078 MegaRAID SAS 1078256MB Cache with ECC 512MB Cache with ECC optional BBU optional BBUSAS 3Gb/sec SAS 3Gb/sec8 internal ports 8 internal ports

PCIe x4, 160mm PCIe x4, 160mm

without bracket without bracket Only one BBU per Systemmax. 1x per system max. 1x per system possible, either for

MegaRAID SAS 8344 ELP

or for MegaRAID SAS 1078S26361-F3257-E55 S26361-F3257-E55

Cache Battery Backup Unit Cache Battery Backup Unit

with 55cm cable set with 55cm cable set for loose delivery please ordermax. 1x per System max. 1x per System S26361-F3257-L10

Section G-VIII 3.5" SAS Hard disk drives Section G- IX 3.5" SATA Hard disk drives

S26361-F3218-E160HD 160GB 7.2krpm 3.5"7200rpm,

System configurator and order-information guideG1 PRIMERGY RX200 S4 Status 2008-12-17

G2

S26361-F3204-E573 S26361-F3204-E514HD 73GB 15krpm 3.5" Hard disk 146GB 15krpm 3.5"15.000rpm,

System configurator and order-information guideH PRIMERGY RX200 S4 Status 2008-12-17

Section H-VI Drive Bay for 2.5" HD Basic Unit

4x 2.5" HDD OptionDrive Bay with up to 4x 2.5" slots

Section H-VII Modular Raid 0/1 and Raid5 Controller for 2.5" HD`s

S26361-F3257-E44 port SAS RAID Controller Modular Raid 0/1 controller with IME support for SAS-HDsLSI IME (Integrated Mirroring Enhanced) offers the RAID levels 0, 1, 1E MegaRAID SAS 1064 IME is a RAID 0, 1 implementation, whereby RAID 1 can operate no Cache, no BBU an odd number of hard disks. Up to 4 hard disks including one hot spare HD RAID 0, 1 & 1E are possible (limited by HHD slots in system). SAS 3Gb/sec Windows 2003 as well as SUSE and RedHat Linux are supported 4 internal ports The SAS IME solution supports 2 independent RAID volumes.PCIe x4, 160mm There is no support of any external storage by this RAID solution. max. 1x per system

1xModular Raid 5 controller for SAS/SATA-HDsRAID levels 0, 1, 10, 5, 50, 6 and 60 are supported There is no support of any external storage by this RAID solution.

S26361-F3257-E256 S26361-F3257-E5128 port SAS RAID Controller 8 port SAS RAID ControllerLSI LSIMegaRAID SAS 1078 MegaRAID SAS 1078256MB Cache with ECC 512MB Cache with ECC optional BBU optional BBUSAS 3Gb/sec SAS 3Gb/sec8 internal ports 8 internal ports


without bracket without bracketmax. 1x per system max. 1x per system

S26361-F3257-E55 S26361-F3257-E55 Only one BBU per SystemCache Battery Backup Unit Cache Battery Backup Unit possible, either for with 55cm cable set with 55cm cable set MegaRAID SAS 8344 ELPmax. 1x per System max. 1x per System or for MegaRAID SAS 1078

Section H-VIII 2.5" SAS Hard disk drives

Up to 4x 2.5" SAS hard disks can be configured.

S26361-F3208-E173 S26361-F3208-E114HD 73GB 10krpm 2.5" HD 146GB 10krpm 2.5" 10000rpm,

System configurator and order-information guideI PRIMERGY RX200 S4 Status 2008-12-17

Section X External SAS Disk Array or SCSI drives

External SAS-controller for external SAS Disk Array

S26361-F3215-E1 This Controller 8 port SAS RAID Controller requires a full hight PCI slot.LSI

MegaRAID SAS 8344 ELP

256MB Cache with ECC

RAID 0, 1, 10, 5, & 50

optional BBU

SAS 3Gb/sec

4 internal / 4 port external It is only a maximum cable

PCIe x4, 174mm length of 2m supported

full height bracketmax. 1x per system

S26361-F3257-E55 Only one BBU per SystemCache Battery Backup Unit possible, either for with 55cm cable set MegaRAID SAS 8344 ELPmax. 1x per System or for MegaRAID SAS 1078

S26361-F3890-E201 S26361-F3890-E210

8 port SAS RAID Controller 8 port SAS RAID Controller

LSI LSI

MegaRAID SAS8880E MegaRAID SAS8880E

512MB Cache with ECC 512MB Cache with ECC

RAID 0, 1, 10, 5, 50, 6 & 60 RAID 0, 1, 10, 5, 50, 6 & 60

without iBBU with iBBU

SAS 3Gb/sec SAS 3Gb/sec

8 port external 8 port external


low profile bracket low profile bracketmax. 1x per system max. 1x per system

SCSI-controller for external drives and peripheral devices

Only released forS26361-F3270-E201 SX10. All contr.SCSI U320 Controller for the connectionAdaptec SCSI Card 29320LPE of external storage

2x PCIe x1, systems areint: LVD HD68 delivered withoutext: VHDCI 68pin cables. For themax. 2x per system configuration of

external cabling

see configurator

SAS-controller for external backup drives

S26361-F3271-E201SAS Controller 3Gb/s 8 port LPLSI SAS3442E-R Low Profile

2x PCIe x4, int: 4 portext: 4 portmax. 2x per system

J


System configurator and order-information guideJ PRIMERGY RX200 S4 Status 2008-12-17

Section XI Fibre Channel

Fibre Channel Controller for external storage systems

S26361-F3306-E201 S26361-F3306-E202 S26361-F3483-E201 S26361-F3483-E2024GBit/s FC Controller 4GBit/s FC Controller 4GBit/s FC Controller 4GBit/s FC ControllerEmulex Emulex Qlogic QlogicLPe1150, Low Profile bracket LPe11002, Low Profile bracket QLE2460, Low Profile bracket QLE2462, Low Profile bracket1 channel 4GBit/sec FC Controller 2 channel 4GBit/sec FC Controller 1 channel 4GBit/sec FC Controller 2 channel 4GBit/sec FC ControllerLC Interface for 50m Fiber LC Interface for 50m Fiber LC Interface for 50m Fiber LC Interface for 50m FiberPCIe x4, 170mm PCIe x4, 170mm PCIe x4, 170mm PCIe x4, 170mmmax. 2x per system max. 2x per system max. 2x per system max. 2x per system

2x

No mix and match for different Fibre Channel controllers supportedexcept LPe1150 and LPe11002 Emulex PCI-Express Controller

S26361-F3864-E201 except QLE2460 and QLE2462 QLogic PCI-Express Controller 4GBit/s FC ControllerEmulexLPe111, Low profile bracket1 channel 4GBit/sec FC Controller All controllers for the connection of external storage systems are delivered without cables. LC Interface for 50m Fiber For the configuration of external cabling see the configurator for external storage systems.PCIe x4, 170mmmax. 2 per system For Fibre Channel SAN also other componets like switches, SFPs and optical wires are

orderable (for details see price liste)

Internal cables and adapter are included all in the basic unit or the components.

S26361-F3961-E201 S26361-F3961-E2028GBit/s FC Controller 8GBit/s FC ControllerEmulex EmulexLPe1250, low profile bracket LPe12002, low profile bracket1 channel 8GBit/sec FC Controller 2 channel 8GBit/sec FC ControllerLC Interface for 50m Fiber LC Interface for 50m FiberPCIe x4, 170mm PCIe x4, 170mmmax. 1x per system max. 1x per system

K


System configurator and order-information guideK PRIMERGY RX200 S4 Status 2008-12-17

Section XII Communication / Network

Two 1GBit on-board LAN Controllers Teaming: Failover, Load BalancingGigabit Ethernet Controller on-board The Intel LAN Controllers 1000TX and 1000SX2x 1GBit BroadCom 5708 can be used with the on-board controller in Teaming Mode. Server Adapter, BroadCom w. TOE With Broadcom on-board Gigabit Ethernet adapters ext: for RJ 45-connector for teaming the Broadcom drivers must be used. SW: AFT, VLAN, Fast Channel Two onboard LAN ports can likewise educate a team.

* iSCSI boot by system BIOS supported.

2 slots PCIe x8 ( wired x8 ) available A PCIe x1 or x4 card can also be plugged in a PCIe x8 slot

C) PCI-Express Adapter 1000TX/SX

S26361-F3241-E201 (Glyndon ) S26361-F3242-E201 (Sheepshead Bay) S26361-F3228-E201 ( Redwater )Gigabit Ethernet Contr. 1000TX LP Gigabit Ethernet Contr. 1000SX Gigabit Ethernet Controller Dual 1000TX LPEth Ctrl 1x1Gbit PCI-e Pro/1000PT Cu LP Eth Ctrl 1x1Gbit PCI-e Pro/1000PF LC LP Eth. Ctrl 2x1Gbit PCIe PRO/1000PT Cu LP

Intel PRO/1000 PT Server Adaptor Intel PRO/1000 PF Server Adapter Intel Pro/1000PT dual Server AdapterPCIe x1, Low Profile PCIe x4, Low Profile PCIe x4, Low Profileext: for RJ45-connector, Cat 5 ext:LC-connector ext: for RJ45-plug, Cat 5max.2x per system max.2x per system max.2x per system

S26361-F3516-E201(Shelter Island)

Gigabit Ethernet Controller 1000TX LP2x Eth Ctrl 1x1Gbit PCI-e Gigabit CT DT Cu LP

Intel Gigabit CT Desktop AdapterPCIe x1ext: for RJ45-connector, Cat 5max. 2x per system

D) Quad Port PCIe Adapter 1000TX

S26361-F3462-E201 ( Kirkwood 2 )Gigabit Ethernet Controller Quad 1000TX LPEth. Ctrl 4x1Gbit PCIe PRO/1000PT Cu LPIntel Pro/1000PT Quad Port Server AdapterPCIe x4, Low Profileext: for RJ45-plug, Cat 5max. 2x per system

L


System configurator and order-information guideL PRIMERGY RX200 S4 Status 2008-12-17

Section XIII System Management Products (RemoteView)

S26361-F1790-E241 iRMC S2 (integrated Remote Management Controller) onboard server management iRMC S2 advanced pack controller with dedicated 10/100 Service LAN-port and integrated graphics controller.integrated remote management controller The Service LAN-port can be switched alternatively on standard Gbit LAN port

activation key forgraphical console redirectionand remote media redirectionmax. 1x per system

S26361-F2557-E204 S26361-F2557-E104Local Service Panel incl. mount. kit Local Service Display Option KitCustomer Self Service LCD display with installation kitCSS module incl. mounting kit0.5" x 5.25" 0.5" x 5.25"max. 1x per system max. 1x per system

Section XIV Miscellaneous

Options and other peripheralsFor other options, refer to SystemArchitect and Pricelist.These options are supplied lose with the shipment.For suitable peripherals for this product, please refer to SystemArcitect.

Section XV Country specific power cord

Country specific power cords are not required for rack versions, except for USA&Canada.Power cords are shipped in a rack version with inlet connector for non-heating apparatus.Description in englisch. Both included in basic unit.(1x with Standard PSU, 2x with hot plug upgrade)

T26139-Y1742-E10 USA, CanadaFor shipments to USA&Canada, you have to orderone power cord (1,8m, grey) per power supply.

End PRIMERGY RX200 S4



Change Report

Date Order number Changes

2008-12-17 S26361-F1790-E221 RemoteView Software V5.0 - no longer available2008-11-27 S26361-F3204-E130 HD 300GB 10krpm 3.5" - no longer available2008-11-06 S26361-F3263-E524 Memory 8GB - changed to S26361-F3263-E7242008-11-06 S26361-F3263-E523 Memory 4GB - changed to S26361-F3263-E7232008-10-25 S26361-F3516-E201 Gigabit Ethernet Controller 1000TX LP- now available2008-09-30 S26361-F3881-E350 New X5270 3.50GHz CPU now available2008-09-30 S26361-F3880-E566 New L5430 2.66GHz CPU now available2008-09-30 S26361-F3880-E333 New X5470 3.33GHz CPU now available2008-09-30 S26361-F3265-E100 HD SATA 3Gb/s 1TB 7.2k hot plug 3.5" - as soon as available2008-09-27 S26361-F3961-E202 2 channel 8GBit/sec FC Controller now available2008-09-27 S26361-F3961-E201 1 channel 8GBit/sec FC Controller now available2008-09-01 S26361-F3531-E1 Blu-ray Combo drive HH SATA Low Profile now available2008-07-14 S26361-F3204-E545 HD 450GB 15krpm 3.5" - as soon as available2008-07-04 S26361-F3890-E210 new 8 port SAS RAID Controller with iBBU - as soon as available2008-07-04 S26361-F3890-E201 new 8 port SAS RAID Controller without iBBU - as soon as available2008-06-24 S26361-F3208-E136 HD 36GB 10krpm 2.5" no longer available2008-06-05 S26361-F3866-E400 Xeon LV DP L5335 no longer available2008-04-17 S26361-F3271-E201 new SAS Controller 3Gb/s 8 port 2008-04-14 S26361-F3881-E500 new Low Voltage Quad-Core CPU (3.00GHz/6M/1333) / 40W - as soon as available2008-03-11 S26361-F3204-E173 no longer available2008-03-11 S26361-F3204-E114 no longer available2008-02-27 S26361-F3880-E550 new Low Voltage Quad-Core CPU (2.50GHz 2x6M/1333) / 50W - as soon as available2008-02-27 S26361-F3880-E533 new Low Voltage Quad-Core CPU (2.33GHz 2x6M/1333) / 50W - as soon as available2007-11-28 First Release


rx200 s4 config

Documents