setting ip cctv
DESCRIPTION
Setting Ip CctvTRANSCRIPT
A. Setting Camera1. Siapakan Power Supply untuk kamera2. Siapkan PC atau Laptop dan kabel UTP (cross/straight),hub switch3. Masukkan Kabel UTP ke port yang ad dikamera4. Selanjutnya buka IE (internet Explorer)5. Gunakan aplikasi IP scan/IP tool bawaan camera6. Setelah didapat IP default kamera7. Rubah IP default sesuai IP yang akan dipakai
B. Setting Switch
1.Siapkan Power Supply untuk Switch (core, distribution dan Access )
2. Siapkan PC atau Laptop dan kabel console (bawaan dari Switch)
3. Masukkan kabel console ke switch
4. selanjutnya di PC atau Laptop buka
I.1. Setting terminal parameters.- Start PC dan jalankan program Hyperterminal- Klik START > Programs > Accessories > communications >
Hyperterminal
Gambar 1.1
Gambar 1.2
II. Memberikan IP pada interface MGMT
Mis. Ip address : 192.168.0.1NetMask : 255.255.255.0
<H3C>System view[H3C] interface M-Ethernet0/0/0[H3C-interface M-Ethernet0/0/0]ip address 192.168.0.1 255.255.255.0[H3C-Interface M-Ethernet0/0/0]quit[H3C]
III. Vlan
III.1. Membuat VlanMis.Vlan ID : 10Name : PerangkatTipe : byportPort : ge-4/0/1
<H3C>System View[H3C]vlan 10 name Perangkat[H3C#]vlan 10[H3C-Vlan10]interface ge-4/0/1
III.2. Menghapus Vlan
<H3C>System View
[H3C]undo vlan 10
III.3. Memberi IP pada VlanMis.Vlan ID : 10Ip Address : 192.168.1.1 / 24
<H3C>System View[H3C#]interface vlan-interface 10[H3C-Vlan-interface10] ip address 192.168.1.1 255.255.255.0
III.4. Menghapus IP Vlan
<H3C>system View[H3C]interface vlan-interface 10[H3C-Vlan-Interface10]undo ip address
III.5. Menambah port member VlanMis.Vlan ID : 10Port : ge-4/0/2
<H3C>System view[H3C]vlan 10 port member ge-4/0/2
IV. MembuatPort Trunk
Mis.Port : ge-4/0/48
<H3C>System View[H3C]interface ge-4/0/48[H3C-Gigabitethernet4/0/48]port mode trunk[H3C-Gigabitethernet4/0/48]port trunk allowed vlan all
V. Membuat Link Aggregation Mis. Port : Ge-4/0/48 dan Ge-4/0/47Allowed Vlan : Vlan 10Group : 1
<H3C> system View[H3C]interface bridge-aggregation 1[H3C-Bridge-Aggregation1] port access vlan 10[H3C-Bridge-Aggregation1]quit
[H3C]interface gigabitethernet 4/0/48[H3C-Gigabitethernet4/0/48]port link-aggregation group 1[H3C-Gigabitethernet4/0/48]port access vlan 10
Warning: This port is a member of the link aggregation group. If configuration of the whole
group is required to be modified, please configure it under the aggregation interface view.
Otherwise, this operation may interrupt network traffic.Continue?[Y/N]: y
[H3C-Gigabitethernet4/0/48]quit[H3C]interface gigabitethernet 4/0/47[H3C-Gigabitethernet4/0/47]port link-aggregation group 1[H3C-Gigabitethernet4/0/47]port Access vlan 10
Warning: This port is a member of the link aggregation group. If configuration of the whole
group is required to be modified, please configure it under the aggregation interface view.
Otherwise, this operation may interrupt network traffic.Continue?[Y/N]: y
[H3C-Gigabitehternet4/0/47]quit[H3C]
VI. Membuat Static RoutingMis.Destination : 192.168.7.0Mask : 255.255.255.0Next Hope : 192.168.100.254
<H3C>system view[H3C]ip route-static 192.168.7.0 255.255.255.0 192.168.100.254
VII. Mengaktifkan Telnet<H3C>system view[H3C]telnet server enable[H3C]user-interface vty 0 4[H3C-ui-vty1]authentication-mode password[H3C-ui-vty0-4]set authentication password chipper 12345678
C. Setting Server 1. Siapkan power supply untuk server2. Install server dengan OS sesuai spek3. Selanjutnya install aplikasi kamera CCTV sebagai master4. Dan install managemant storage
D. Setting Client1. Siapkan power supply untuk client2. Install client dengan OS sesuai spek3. Selanjutnya install aplikasi kamera CCTV sebagai master
E. Setting Storage1. Menjalankan Command view atau web module(navigator module)2. Menginisialisasi Storage system3. Membuat LUN4. Membuat disk group5. Menambah Host ke storage
6. Menambah port ke storage7. Menbuat virtual disk