sizing adeni
TRANSCRIPT
-
8/11/2019 Sizing Adeni
1/7
1. Gas Turbine
In This Process, a gas turbine is used as utility to produce electricity and supply
power to for generator. For the utility and sizing we leave it to the vendor
Equipment Specification
Equipment Name Gas Turbine
Type Solar Titan 250
3-Stage , Axial
Full Tilting-Pad Thrust Bearing
Equipment Code GT-101
Function Decreasing the gas pressure andproduce electricity
Quantity 1
Equipment Type Gas Turbine
Material Carbon Steel
Operating Condition
Flow rate (m3/jam) 7.53212
Max Speed 7000 rpm
Pressure Ratio 2,416x104
Inlet Pressure (kPa) 2662
Outlet Pressure (kPa) 0.6432
Power (MW) 210
Exhaust Flow (kg/hr) 245 660
Exhaust Temperature 465
2. Pump
P-101 Natura GasPower Plant
P-01
Function Pumping water from water tank to HRSG
Type Single Stage Centrifugal Pump
Impeller Francis Vane
Material Stainless Steel
Pressure ratio 15.2
-
8/11/2019 Sizing Adeni
2/7
Flow (m3/s) 0.0266
Efficiency 75%
Suction Pressure (kPa) 6.895
Discharge Pressure (kPa) 104.8Head 32.709 ft
BHP 4.6 HP
1. Determining the type of pump and Material
The pump used is a type of centrifugal pumps and the material is stainless steel
2. Calculation
14.2 psi
Mass Flow = 9.566 x 104kg/h
Flowrate = 95.39 m3/h = 419.98 GPM
Efficiency = 75%
1800 rpm
()()
[()]
-
8/11/2019 Sizing Adeni
3/7
From Figure above, it can be seen thay type of impeller for this pump is the
Francis Vane.
Pump Horsepower
BHP = 4.638 hp
WHP = 3.479 hp
-
8/11/2019 Sizing Adeni
4/7
P-02 Acid Plant
P-01
Function Pumping water
Type Single Stage Centrifugal PumpImpeller Francis Vane
Material Stainless Steel
Quantity (m3/s) 0.0068
Efficiency 75%
Suction Pressure (kPa) 100
Discharge Pressure (kPa) 200
Head 15.255 ftBHP 1,22 Hp
1. Determining the type of pump and Material
The pump used is a type of centrifugal pumps and the material is stainless steel
2. Calculation
14.5 psi
Mass Flow = 3.603 x 104kg/h
Flowrate = 16.41 m3/h = 72.25 GPM
Efficiency = 75%
1800 rpm
()()
[()]
-
8/11/2019 Sizing Adeni
5/7
From Figure above, it can be seen thay type of impeller for this pump is the
Francis Vane.
Pump Horsepower
BHP = 0.815 hp
WHP = 0.611 hp
P-03 Acid Pant
P-02
-
8/11/2019 Sizing Adeni
6/7
Function Pumping water
Type Single Stage Centrifugal Pump
Impeller Radial Vane
Material Cast IronQuantity (m3/s) 0.0074
Efficiency 75%
Suction Pressure (kPa) 100
Discharge Pressure (kPa) 200
Head 33.597 ft
BHP 1,323 Hp
1. Determining the type of pump and Material
The pump used is a type of centrifugal pumps and the material is stainless steel
2. Calculation
14.5 psi
Mass Flow = 1.634 x 104kg/h
Flowrate =16.39 m3/h = 72.16 GPM
Efficiency = 75%
1800 rpm
()()[()]
-
8/11/2019 Sizing Adeni
7/7
From Figure above, it can be seen thay type of impeller for this pump is the
Radial Vane.
Pump Horsepower
BHP = 0.814 hp
WHP = 0.61 hp