sıvı seviye rölesi / liquid level controller · elektroliz olayının oluşmaması için...
TRANSCRIPT
FONKSİYON AÇIKLAMASIFONKSİYON TANIMI
LC3 sıvı seviye kontrol rölesi, elektrotlar(A ve B) arasındaki sıvı direncini ölçerek iletkensıvıların seviyesini kontrol eder. Ölçülen dirençdeğeri ön panelden ayarlanmış olan dirençdeğerinden küçükse, çıkış rölesi çeker.
Elektroliz olayının oluşmaması için sıvıya ACbir sinyal uygulanmaktadır.
Üç elektrodlu çalışma:Hazne içindeki sıvının seviyesi B elektrodunaulaştığı anda çıkış rölesi çeker, seviye Belektrodunun altına indiğinde röle konumunukorur. Çıkış rölesi, seviyenin A elektrodunun altınainmesiyle bırakır. Rölenin tekrar çekmesi için sıvıseviyesinin B elektroduna ulaşması gerekir.
İki elektrodlu çalışma:İki elektrodlu çalışma için A ve B elektrodukullanılmalıdır. Hazne içindeki sıvının seviyesiB elektroduna ulaştığı anda çıkış rölesi çeker.Seviye B elektrodunun altına inip, cıhazın önpanelindeki gecikme süresi ayar potu ileayarlanan süre kadar kalırsa çıkış rölesi bırakır.
min:
:
ON:
max:
TOFF
Un:
Elektrod(A - B) teması :
Elektrod(A - C) teması :
R:
> TOFF
A
B
C
A
B
tip sipariş no270 001LC3
A
B
CA
B
CA
B
CA
B
CA
B
CA
B
C
Çıkış rölesi kontakları:1-3
1-2
Çıkış rölesinin hazneiçindeki sıvının seviyesinebağlı değişimi:
Çalışma frekansı 35 .. 70Hz
Çıkış kontağı
Koruma sınıfı
Saklama sıcaklığı
Bağlantı şekli
Maksimum anahtarlama akımı
Çalışma sıcaklık aralığı
Maksimum anahtarlama gerilimi
Maksimum anahtarlama gücü
1 C/O
IP20
-40°C .. 75°C
Raya montaj
10A
-20°C .. 60°C
250V AC
1250VA
İşletme gerilimi 150 .. 500V AC
Hassasiyet ayar aralığı 5 .. 100KΩ
Histerisis %25
Gecikme süresi ayar aralığı 0.1 .. 10sn
Sıvı Seviye Rölesi /Liquid Level Controller
type order no270 001LC3
A
B
CA
B
CA
B
CA
B
CA
B
CA
B
C
Output relay contacts:1-3
1-2
The status change ofoutput relay with respectto liquid level:
FUNCTION STATEMENTFUNCTION ILLUSTRATION
LC3 controls levels of conductive liquids by measuringthe resistance of the liquid between probes. If measuredresistance is less than the value adjusted from the frontpanel, output relay will be activated.
To avoid electrolysis, an AC signal is applied to the liquid.
3 electrodes mode:When the level of liquid in the tank reaches toelectrode B, the output relay is activated and staysin this position even if the level drops below theelectrode B level. The output relay is deactivatedwhen the liquid level drops below electrode A level.Re-activation occurs when the level reaches to theelectrode B level.
2 electrode mode:For 2 electrodes mode of operation, A and B electrodesare used. When level of liquid in the tank reaches toelectrode B, output relay is activated. When the liquidlevel drops below electrode B and continually staysthere for the adjustable time delay (adjusted on the frontpanel knob); output relay will be de-energized.
min:
:
ON:
max:
TOFF
Un:
Probe (A - B)conduction :
Probe (A - C)conduction :
R:
> TOFF
A
B
C
A
B
Operating frequency 35 .. 70Hz
Output contact
Protection class
Storage temperature
Connection
Maximum switching current
Operating temperature
Maximum switching voltage
Maximum switching power
1 C/O
IP20
-40°C .. 75°C
Rail mounted
10A
-20°C .. 60°C
250V AC
1250VA
Operating voltage 150 .. 500V AC
Sensitivity adjustment range 5 .. 100KΩ
Hysteresis %25
Time delay adjustment range 0.1 .. 10sec
29.1mm
50.6mm57.5mm
45.5mm
62mm
90mm
36mm
* : In case of metal tank, terminal C can be directly connected to metal surface instead of using C electrode.
2
U2U1
1 3
150..500V ac
A B C
A
B
C
*
(Relay)
2
U2U1
1 3
150..500V ac
A B C
A
B
C
*
* : Haznenin metal olması durumunda C elektrodu kullanılmayıp kablo direkt olarak metal yüzeye bağlanabilir.
(Röle)
Rev
isio
n N
o: 29102015