technical catalogue - پتروشیمی جمex5) ... technical catalogue 2018 8 ... component...
TRANSCRIPT
TECHNICALCATALOGUE
2 0 1 8V e r 3 . 0
About JPC
index:
7
12
22
26
76
42
90
OlefinChemical & Olefin Plants:
Polyolefin Plants:
Butadiene, Butene-1
HDPE
Polypropylene
LLDPE
ABS-Rubber
About JPCAbout JPC .................................................................... 7Vision, Mission, Values, Goals................................... 8-9JPC in the Global Markets........................................... 11
Olefin ProductsProducts Capacity of Olefin plant............................... 14Ethylene...................................................................... 15Propylene................................................................... 16Pyrolysis gasoline........................................................ 17C4 cut.......................................................................... 18Fuel oil........................................................................ 19Hydrogen.................................................................... 20Methane..................................................................... 21
BD - B1 ProductsButadiene................................................................... 24Butene-1..................................................................... 25
HDPE ProductsProduct s Capacity of HDPE plant.............................. 28HF4760(BL3)............................................................... 30HM8355(BL4) ............................................................. 32HM5010T2N (EX3) ..................................................... 34HMCRP 100 N(PE100)................................................. 36HMCRP 100 (Black)..................................................... 38HM9450F(EX5)............................................................ 40
LLDPE ProductsProducts Capacity of LLDPE plant................................ 44LL22502AA/22502KJ ................................................... 47LL22501AA/22501KJ ................................................... 48HPLL18XF5/N .............................................................. 50HD5000s ...................................................................... 52HD60505/UV ............................................................... 54HD60507/UV................................................................ 56CC52501...................................................................... 58CC52502...................................................................... 60CC52502SU.................................................................. 62HD52505/UV................................................................ 64HD52511/UV................................................................ 66HD52518..................................................................... 68LL32604UV................................................................... 70MD38504UV ................................................................ 72HD60511/UV................................................................ 74
Polypropylene ProductsHP525J ......................................................................... 78HP550J ......................................................................... 79HP510L ........................................................................ 80HP552R ........................................................................ 81HP564S ........................................................................ 82EP440G ........................................................................ 83EP440L ......................................................................... 84EP3130UV.................................................................... 85EP548R ........................................................................ 86EP548T ........................................................................ 87RP345S ........................................................................ 88
ABS-Rubber ProductsF332 ............................................................................. 92E332 ............................................................................ 93L322............................................................................. 94F232 ............................................................................. 95B432/E......................................................................... 96B532/E......................................................................... 97B732/E......................................................................... 98D232/M3..................................................................... 99C442.......................................................................... 100SOLT6302................................................................... 102SOLT161B..................................................................103SOLT6306................................................................... 104SOLTB183.................................................................. 105InteneP30.................................................................. 106BR245........................................................................ 107BR277........................................................................ 108
Innovations in the products of JAM Petrochemical Company are shown with the this symbol.
JAM Petrochemical CompanyTechnical Catalogue 20186
JAM Petrochemical CompanyTechnical Catalogue 2018 7
About JPCJAM Petrochemical Company (Public stock) has been founded in order to achieve country’s macro plans in petrochemical industry for the purpose of operation of south pars gas field with the registered No 32285, in 2000.This large industrial complex, with the total area of 77 hectares is located in Asaluyeh special economic zone, in the Boushehr province. JAM Petrochemical Company (JPC) after almost a decade of operation and including of Olefin, HDPE, LLDPE, Butadiene and Butene-1 production units, still is one of the largest Olefin producers all over the world, and also polymer based products in Iran.JPC is the most prominent complex in south Pars special economic zone by production and supply various grades of petrochemical products in domestic and global market and move forward on development and promotion is one of the important complexes of petrochemical industry in economic arena.
JAM Petrochemical CompanyTechnical Catalogue 20188
JAM Petrochemical Company intends to make twice its own production, by the year of 2021, in compare with of the year of 2016.
As a market-oriented company and as a leader in petrochemical industry and supplier of diversified products in olefin chain, JAM Petrochemical Company seeks to achieve maximum value through development of value chain and enhance permanent competitive advantages on an international scale. This company, is committed to meet the expectations of the stakeholders, safe and sustainable production, accepting social responsibilities and improve the environment based on valuable human capital and using unique position of Iran, as one of the largest olefin production complex in Iran and over the world.
Vision
Mission
JAM Petrochemical CompanyTechnical Catalogue 2018 9
1. Preserving and protecting of shareholders rights and other beneficiaries is one of company’s fundamental values.
2. Legalism, international and national laws administration which is related to mission of company is another fundamental value of company.
3. Making alignment and coordination between company goals and employees’ private goals for create a balance between work and family life. It has moral value to improve satisfaction of employees and their families.
4. Continuous excellence of the performance in all organizational aspects, increase quality and sustainability of products, increase customer satisfaction and also concern for human dignity is a value for JAM Petrochemical Company.
5. Human resource and capital efficiency and moral and spiritual and financial capital maintenance are of value in petrochemical Jam Company.
6. Development of learning culture, being innovative and creative, continuous improvement, group work, group participation, being knowledge-based, being responsible and having customer oriented strategy is sentimental values for JAM Petrochemical Company.
1. Increase production capacity through promotion of productivity and systems improvement.2. Perform project execution for development for the purpose of make completion of polymer
products value chain. 3. Increase the quality, production identical basket of goods and suitable innovative for the purpose
to increase benefit.
Values
Goals
JPC in theGlobal MarketsJPC is among one of the largest exporters of Iranian polymer products. JPC continues to be ranked first for the export of high density polyethylene products. 66 percentage of production was exported to more than 40 countries around the world in 2016.At the moment, China, Turkey, India, CIS, the Far East, European ports and neighboring countries serve as the entryway of JPC products to international markets. JPC endeavors to enhance its share of target markets and at the same time places great emphasis on potential markets. Africa and South America are another potential markets which are expected to allocated themselves a considerable part of JPC export. According to the strategic policy of JAM Petrochemical Company, for integrated marketing and selling of all products of Jam petrochemical group, the task of exporting JAM Petrochemical Company and Jam Propylene products has been delegated to Topco company from February 2017.
New ProductsDevelopmentin JPC Delivering a commercially successful product to market begins with identification of the needs of the target market and focusing on fulfilling those needs through production.Relying on the principle of competitiveness at the national and international level and supplying the needs of the market and the customers, Jam Petrochemical Company has paid special attention to variety of its products and their upgrade and development. The research and technology unit of this company has identified intended products according to the existing needs and is implementing required scientific and technical investigations in order to produce these materials. It also designs and produces its intended products through interaction with labs, universities, research centers and industrial and operational units and also through attending exhibitions and taking part in domestic and international seminars. This company also performs consistent activities and projects concerning technology development and improvement of the properties and performance of the products.
Innovations in the products of JAM Petrochemical Company are shown with the this symbol.
1
Olefin Unit Under the license of Technip, with its annual capacity of producing 1,320,000 tons of ethylene and 306,000 tons of propylene as well as a total annual capacity of 2,359,000 tons of products, JPC Petrochemical Company’s olefin unit is considered as one of the largest olefin units both globally and nationwide. Olefin unit has been constructed with the help of modern technologies and its capacities have been determined by taking into consideration the global scale. 1. Compared to other similar units, unique characteristics of JPC Petrochemical olefin unit include its high production capacity and possibility of utilizing (flexible) dual purpose furnaces which allow this unit to make use of both liquid and gas feed. 2. Feed diversity, capacity to produce a wide range of products, and relationship with other important units, in the South Pars Zone, of gas and petrochemistry can be regarded as other strategic features of JPC’s olefin unit.Ethylene, propylene, Hydrogen, dry pyrolysis gasoline, furnace fuel oil (CFO) and C4 compounds.
OlefinProducts
JAM Petrochemical CompanyTechnical Catalogue 201814
Applications Nominal Capacity1000 T/YProducts
Polyethylenee, PVC1345Ethylene
Polypropylene305Propylene
Feed for downstream plant265C4cut
To Aromatic Plant216Pyrolysis gasoline
Feed for downstream plant38Fuel Oil
For hydrogenation1.5Hydrogen
Fuel 3.9Methane
2174.4Total
Products Capacity of Olefin plant
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 15
SPECIFICATIONCOMPONENT
vol % min99.9Ethylene
ppm vol max1000Methane + Ethane
ppm vol max500Ethane
ppm vol max5Acetylene
ppm vol max10C3 & Higher
ppm vol max2Carbon Monoxide
ppm vol max5Carbon Dioxide
ppm vol max10Water
ppm vol max5Oxygen
ppm vol max10Hydrogen
ppm vol max100Nitrogen
ppm vol max10Oxygenated Compounds
ppm vol max1 Basic Nitrogen CompoundeCaloulated as NH3
mg/kg max2Total sulphur
ppm vol max0.5Methanol
ppm vol max0.2Total Combined Nitrogen
ppm vol max0.02COS
ppm vol max0.3Mercaptans
Olefin made via Techinp Tecnology
Ethylene Is a simple olefin, the chemical formula is C2H4 has a prominent role in the petrochemical industry. It is colorless flamable gas.
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201816
Olefin made via Techinp Tecnology
Propylene Also called propane, a colorless, flamable, gaseous hydrocarbon, C3H6, obtained from low molecular weight constituents of petroleum.
SPECIFICATIONUnitCOMPONENTmin 99.8% volPropylene
max 0.2 %% volPropanemax 5ppm volHydrogenmax 1ppm volEthylenemax 1ppm volButenesmax 1ppm volPentenes
max 20ppm volNon-condensablesmax 20ppm volEthanemax 10ppm volButane-pentanesmax 1ppm volC6-C12 Hydrocarbonsmax 1ppm volAcetylenemax 1ppm volMethyl-acetylenemax 1ppm volPropadiene
max 10ppm volButadienemax 2ppm volOxygen
max 0.03ppm volCarbon Monoxidemax 2ppm volCarbon Dioxide
max 0.02ppm volCOSmax 1ppm wtTotal sulphurmax 5ppm volMethanolmax 5ppm volIsopropanolmax 2ppm wtWater
max 0.01ppm volArsinemax 0.01ppm volPhosphine
max 1ppm wtAmmoniamax 0.05ppm volCyclopentadiene
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 17
Olefin made via Techinp Tecnology
Pyrolysisgasoline
Pyrolysis gasoline, is a naphtha-range product with a high aromatics content used either for gasoline blending or as a feed stock for aromatics plants.
Analysis MethodSpec.UnitSPECIFICATIONmax 50 wt%Aromaticsmax 30wt%Benzene.………wt%Toluene
ASTM D40520.8-0.84gr/cm3Density at 15.6CASTM D86max 225.cFBPASTM D86min 33.cIBP
ASTM D637840-65kpaR.V.Pmax 21wt%Paraffinesmax 21wt%Isoparaffinesmax 2wt%Naphtenes
max 20wt%OlefinsASTM D5453350mg/kgTotal Sulfur
max 50 mg/100mlGum Contentmax 30ppbLead Content
ASTM E203.………Water Content.………wt%Unknown
ASTM D86.………wt%ResidueASTM D86min 45.c%5RecoveryASTM D86.……….c10%RecoveryASTM D86.……….c20%RecoveryASTM D86.……….c30%RecoveryASTM D86.……….c40%RecoveryASTM D86.……… .c50%RecoveryASTM D86.……….c60%RecoveryASTM D86.……….c70%RecoveryASTM D86.……….c80%RecoveryASTM D86min 175.c90%RecoveryASTM D86.……….cRecovery
-16Color Sybolt
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201818
C4 Cut produced in Ethylene production planets by steam cracking of naphtha. It is a mixture of C4 hydrocarbons mainly 1,3- butadiens, Iso Butene, Butane.
Olefin made via Techinp Tecnology
C4 Cut
SPECITICATIONCOMPONENT45.1 %wt1,3-Butadiene0.12 %wtMethyl-Acetylene0.02 %wtPropadiene0.1 %wtPropylene
0.03 %wtPropane1.13 %wtVinyl-Acetylene19.2 %wti-Butene9.16 %wt1 Butene1.86 %wtCis2-Butene2.58 %wtTrans2-Butene3.94 %wti-Butane
16.56 %wtn-Butane0.06 %wtC5-diolefins0.1 %wtPentenes
0.02 %wtPentanes0.03 %wt2-methyl-butene
100.01 %wtTotal
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 19
Olefin made via Techinp Tecnology
Fuel Oil Fuel oil product is a heavy hydrocarbon cut rich (poly) aromatic components.
VALUETEST/COMPOSITION
>60°CFlash point
approx. >40 cP at 80°CViscosity
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201820
In addition to the guaranteed hydrogen purity, exported hydrogen for use in polyethylene plant will be made available having a non contractual target value for CO content of 30 ppb vol.. This is not a design case. Only facilities have been provided to produce this quality.
Olefin made via Techinp Tecnology
Hydrogen
Composition (contractual)99.99 vol %H2
1 ppm vol maxCO + CO2
0.01 vol % maxCH4 + N2
1 ppm v maxC2H4
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 21
Olefin made via Techinp Tecnology
Methane High pressure Methane is used by EO/EG plant
Compositionmin 93 % volMethanemax 0.5 % volCO/CO2
max 0.05 % volC2H6
max 20 mg/kgC3 and heaviermax 10 mg/kgMethanol andother Oxygenated organic
max 3 % volHydrogen2 mg/kg maxSulphur
max 5.0 ppm volAcetylene
2
BUTADIENEHaving been constructed under BASF license of Germany and assisted by LURGI’s basic engineering and Namvaran’s detail engineering, Butadiene Unit of JAM Petrochemical Company with its annual production capacity of 115,000 tons serves as a brilliant unit nationwide in terms of production, purity grade and product quality. This unit operates as one of JPC’s invaluable production units.
BUTENE-1JPC BUTENE-1 UNIT under AXENS license possessing and assisted by Nargan Co. an annual production capacity of 100,000 tons is honored to serve as the largest Butene production unit nationwide. Besides satisfying the needs of its downstream units in JPC Complex, this unit is also capable of supplying the needs of other polyolefin companies in the country. A major portion of the products generated by this unit is considered to be exported to foreign consumer countries.
BD, B1Products
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201824
Butadiene 1,3-Butadiene is a simple diene with the formula C4H6 . It is an important industrial chemical used as a monomer in the production of synthetic rubber.Annual production 115,000 tons
Butadiene made via BASF Tecnology
Analysis MethodSpecificationUnitAnalysis
ASTM D 2593Min. 99.4wt %1,3 - Butadiene
ASTM D 2593Max. 100wt ppm1,2 - Butadiene
ASTM D 2593Max. 0.5wt %Total Butenes
ASTM D 2593Max. 60wt ppmTotal Acetylenes
BASF's method50-200wt ppmTBC
ASTM D 2426Max. 0.1wt %Dimer (VCH)
BASF's methodMax. 5wt ppmPeroxides
BASF's methodMax. 0.1wt %Non Volatile Residue
ASTM D 5453Max. 5wt ppmTotal SulfurPORTABLE TRACE OXYGEN
ANALYZERMax. 0.2mol % Oxygen in Vapor Phase
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 25
Butene-1 is a linear alpha-olefin with the formula C4H8 and used as a co-monomer for the production of HDPE & LLDPE and manufacturing of polybutene.Annual production 100,000 tons
Butene-1
Butene-1 made via Axense Tecnology
Analysis MethodSpecificationUnitAnalysis
ASTM D 4424Min. 99.5wt %Butene-1
ASTM D 4424Max. 100wt ppmC6+
ASTM D 4424Max. 0.5wt %C4s (Butenes + Butanes)
ASTM D 4424Max. 500wt ppmEthylene
ASTM D 4424Max. 100wt ppmEthane
ASTM D 4424Max. 15wt ppmAcetylenes
ASTM D 4424Max. 20wt ppm1,3-Butadiene
ISO 6381-1981Max. 1wt ppmCarbon monoxide
ISO 6381-1981Max. 1wt ppmCarbon dioxide
ASTM D 2029Max. 15wt ppmWater
ASTM D 5453Max. 1wt ppmTotal Sulphur
3
HDPE Products
High Density Polyethylene Unit Having been established under the license of LYONDELL BASELL Co. and assisted by KRUPP UHDE’s basic engineering, JPC HDPE Unit producing 300,000 tons of products a year is one of the largest polymer units in Iran. In addition to its capability of producing 26 main grades, this unit produces black, oranage, yellow, blue and normal grades. These capabilities of JPC HDPE Unit are unique nationwide and rare in the world.JPC HDPE Unit is the first producer of (pipe) CRP 100 black in Iran.The grades produced by JPC HDPE Unit can be classified as follows:BLOW MOLDING - PIPE PE100/PE80 (NATURAL/COLOR) - FILM - INJECTION MOLDINGSTRETCHED TAPE - MONOFILAMENTIn comparison with other units, some unique features of JPC HDPE Unit are:1. Highly diverse range of products owing to the diverse grades produced;2. A high production capacity; and 3. Capability of producing colored grades and possessing two extruder and packaging lines.
JAM Petrochemical CompanyTechnical Catalogue 201828
DensityMFR(190°C/5 kg)PROPERTY
GRADES g/cm3(g/10 min).UNITISO 1183D 1238ASTM METHOD
17066INTERNAL METHOD1. INJECTION MOLDING
0.960±0.002
0.954±0.002
23±3
11±2
• For transport and stacking bottle crates,particularty bottle creates
• For thick walled highly stressed transport container,e.g. refuse bins and fish crates
HC 7260
HD 7255
2. SMALL BLOW MOLDING
0.944±0.002
0.954±0.002
0.959±0.002
1.1±0.3
1.2±0.3
1.5±0.3
• For disinfectant bottles up to 2 liters, tubes for cosmetics, containers up to 10 liters and petrol cans up to 5 liters
• For container with capacites ranging from a few ml up to 10liters, alsofor production of sheets for thermoforming
• For hollow articles where high stress cracking resistance is not demanded,such as bottles and caisters up to 10 liters,e.g. for fabric softeners
HF 4750
HF4760 (BL3)
HH 4765
3. LARGE BLOW MOLDING
0.951±0.0020.35±0.06• General-purpose grade for large containersHM8355 (BL4)
4. STRETCHED TAPE (RAFFIA)
0.944±0.002
0.944±0.002
1.8±0.3
1.8±0.3
• Stretched films and tapes for production of high-strength knitted and woven
• Tapes to be used for agricultural packagings and as protective cover
HF 7740 F
HF 7740 F2
5. MONOFILAMENT
0.956±0.0020.956±0.002
2.5±0.33.3±0.3
• Production of monofilaments with high tensile strength• Monofilaments for fishing notes , geo textiles and civil
engineering
HF 7750 MHF 7750 M2
Available
Available
Products Capacity of HDPE plant
JAM Petrochemical CompanyTechnical Catalogue 2018 29
DensityMFR(190°C/5kg)PROPERTY
GRADES g/cm3(g/10 min).UNITISO 1183D 1238ASTM METHOD
17066INTERNAL METHOD
6. CABLE
0.946±0.0023.5±0.5cable insulationHF 4750 K
7. PIPE(NATURAL/COLOR)
0.945±0.002
0.944±0.002
0.954±0.002
0.948±0.002
0.957±0.002
0.948±0.002
0.949±0.002
0.45±0.06
0.43±0.03
0.43±0.03
0.22±0.03
0.22±0.02
0.22±0.02
0.22±0.02
• Pressure pipes, e.g. drinking-water and gas pipes,waste pipes and sewer pipes,their fittings and also sheets(UV stabilization and pigments during processing)
• High-quality PE 80 pressure pipes for gas and water transportation(UV stabilization and pigments during processing)
• High-quality PE 80 pressure pipes for gas and water transportation(UV stabilization and pigments during processing)
• Top quality PE 100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE 80 (UV stabilization and/or pigments during precessing)
• Top quality PE 100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE 80 (UV stabilization and/or pigments during precessing)
• Top quality PE 100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE 80 (UV stabilization and/or pigments during precessing)
• Top quality PE 100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE 80 (UV stabilization and/or pigments during precessing)
HM 5010 T2N (EX3)
HM 5010 T3 N
HM 5010 T3 Black
HM CRP100N(PE100)
HM CRP 100 (Black)
HM CRP 100 Blue
HM CRP 100 O/Y
8. FILM
0.956±0.002
0.949±0.002
0.950±0.002
0.957±0.002
0.944±0.002
0.28±0.05
0.28±0.05
0.22±0.05
0.22±0.05
0.18±0.03
• For blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing
• For blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing
• For blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing and sealability
• For blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing
• For blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing
HM 9455 F
HM 9450 F (EX5)
HM 9450 F1
HM 9455 F1
HM 9445 HT
Available
Available
Available
Available
Products Capacity of HDPE plant
JAM Petrochemical CompanyTechnical Catalogue 201830
Product data sheet
HDPE: HF-4760(BL3) MFR 190/5: 0.9-1.5
CharacteristicProperties
• High density and Stiffness, good flowability and impact Strength and
good Stress Cracking resistance.
Main Applications
• For container with capacities
ranging from a few ml up to 10 liters,
also for production of sheets for
thermoforming.
Additives
• Antioxidant/Process
stabilizer
• Lubricant/ acid scavenger
HDPE made via Hostalen Process
HF4760(BL3)
Material properties (This data are typical values and are not to be construed as product specifications.)
Test MethodTypical ValueUnitResin PropertiesISO 113323(g/10 min)Melt Index(21.6)ISO 11331.2(g/10 min)Melt Index(5)
19 FRR (21.6/5)ISO 11830.954g/cm³Density
Test MethodTypical ValueUnitMoulded PropertiesISO 179/ 1 eA9mJ/mm²Notched Impact @ 23 °C
Density: 0.952-0.956 g/cm3
HF-4760 (BL3) is a blow molding grade resin with high density polyethylene with 1-Butene as co monomer which is manufactured by the suspension polymerization of ethylene monomer. Stiffness, good ESCR are it’s spetial properties. High rigidity and good flowablity which made it proper for usage in bottles and small blow molding goods.
31
JAM Petrochemical CompanyTechnical Catalogue 2018 31
Shear-Viscosity @ 190 °C
- On compression moulded according to ASTM D1928CProcessing ConditionsRecommended barrel tempratures range between 190 °C and 280 °C.
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
JAM Petrochemical CompanyTechnical Catalogue 201832
Product data sheet
HM-8355(BL4) is a Blow molding grade resin which is manufactured by suspension polymerization of ethylene monomer. HM-8355 (BL4) is a bi-modal high density polyethylene with Butene-1 as co monomer with general purpose of large container.
Density: 0.949-0.953 g/cm3HDPE: HM-8355(BL4) MFR 190/5: 0.29-0.41
CharacteristicProperties
• High molar mass, easily
processable high stiffness Strength,
good stress Cracking resistance and
very good molding surface finish.
Main Applications
• General purpose grade for large
container.
Additives
• Antioxidant/Process
stabilizer
• Lubricant/ acid scavenger
HDPE made via Hostalen Process
HM8355(BL4)
Material properties (This data are typical values and are not to be construed as product specifications.)
Test MethodTypical ValueUnitResin PropertiesISO 11339.5(g/10 min)Melt Index(21.6)ISO 11330.35(g/10 min)Melt Index(5)
27 FRR (21.6/5)ISO 11830.951g/cm³Density
110%Swell RatioTest MethodTypical ValueUnitMoulded PropertiesISO 179/ 1 eA10mJ/mm²Notched Impact @ 23 °C
33
JAM Petrochemical CompanyTechnical Catalogue 2018 33
Shear-Viscosity @ 190 °C
- On compression moulded according to ASTM D1928CProcessing ConditionsRecommended barrel tempratures range between 190 °C and 280 °C.
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
JAM Petrochemical CompanyTechnical Catalogue 201834
Product data sheet
HM-5010T2N (EX3) is a pipe grade resin which is manufactured by suspension polymerization of ethylene monomer. HM-5010T2N (EX3) is a bi-model high density polyethylene with 1-Butene as co monomer.
Density: 0.943-0.947 g/cm3HDPE: HM-5010T2N (EX3) MFR 190/5: 0.39-0.51
CharacteristicProperties
• Tough and rigid pipe resin.
Main Applications
• Pressure pipes, e.g. drinking-water and gas pipes, waste pipes and sewer pipes, their fittings and also sheets (UV stabilization and pigments during processing)
Additives
• Antioxidant/Process
stabilizer
• Lubricant (processing aid)
/acid scavenger
HDPE made via Hostalen Process
HM5010T2N(EX3)
Material properties (This data are typical values and are not to be construed as product specifications.)
Test MethodTypical ValueUnitResin PropertiesISO 113312(g/10 min)Melt Index (21.6)ISO 11330.45(g/10 min)Melt Index (5)
27 FRR (21.6/5)ISO 11830.945g/cm³Density
Test MethodTypical ValueUnitMoulded PropertiesISO 179/ 1 eA12mJ/mm²Notched Impact @ 23 °CTest MethodTypical ValueUnitMechanical Properties
ISO 1167(4.0 N/mm²) 1000hHydrostatic Strength (80 ºC)
35
JAM Petrochemical CompanyTechnical Catalogue 2018 35
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
Shear-Viscosity @ 190 °C
- On compression moulded according to ASTM D1928CProcessing ConditionsRecommended barrel tempratures range between 190 °C and 280 °C.
JAM Petrochemical CompanyTechnical Catalogue 201836
Product data sheet
HM-CRP100N (PE100) is a natural pipe grade resin which is manufactured by suspension polymerization of ethylen monomer, HM-CRP100N )PE100) is a bi-model high density polyethylene with 1-Butene as co monomer.
Density: 0.946-0.950 g/cm3HDPE: HMCRP 100 N (PE100) MFR 190/5: 0.19-0.25
CharacteristicProperties
• Natural PE100 pipe resin.
Main Applications
• Top quality PE100 pressure
• Pipes for gas and water
transportaion at higher pressures
or with thinner walls as PE80 (UV
stabilization and/ or pigments during
precessing)
Additives
• Antioxidant/Process stabilizer
• Lubricant (processing aid)/ acid
scavenger
HDPE made via Hostalen Process
HMCRP 100N(PE100)
Material properties (This data are typical values and are not to be construed as product specifications.)
- Test specimen from compression moulded sheet at 23°C.- FRR values are statistical and calculated by dividing MFR values.- Notch Impact Test specimen from compressed moulded sheet 23°C and The data quoted are average values .
ASTM MethodUnitTypical ValueTest/CompositionISO1183g/ml30.948Density
28FRR 21.6/5ISO1167h5000 (4.5N/mm2)Hydrostatic Strength (80°c)ISO1133(g/10 min)6.2MFR190°/21.6ISO1133(g/10 min)0.22MFR190°/5
ISO179/1eAmJ/mm224Notched Impact (23°c)
37
JAM Petrochemical CompanyTechnical Catalogue 2018 37
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
Shear-Viscosity @ 190 °C
- On compression moulded according to ASTM D1928CProcessing ConditionsRecommended barrel tempratures range between 190 °C and 280 °C.
PE100-N
1.00E+04
1.00E+05
1.00E+06
1.00E+02
1.00E+03
1.00E+04
1.00E+05
1.00E+00 1.00E+01 1.00E+02 1.00E+031.00E+04
TAU
ap 1
[Pa
];
ETAa
p 1
[Pa*
s];
ETAap 1 [Pa*s]; Ser.: 1; TAUap 1 [Pa]; Ser.: 1;
JAM Petrochemical CompanyTechnical Catalogue 201838
Product data sheet
HM-CRP100 Black is a black pipe grade resin (PE100) which is manufactured by suspension polymerization of ethylene monomer. HM-CRP100 Blue is a bi-model high density polyethylene with 1-Butene as co monomer.
Density: 0.955-0.959 g/cm3HDPE: HM CRP 100 Black(PE100 Black) MFR 190/5: 0.20-0.24
CharacteristicProperties
• Black PE100 resin
Main Applications
• Top quality PE100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE80
Additives
• Antioxidant/Process stabilizer
• Lubricant (processing aid)/
acid scavenger
• Carton Black
HDPE made via Hostalen Process
HMCRP 100 (Black)
Material properties (This data are typical values and are not to be construed as product specifications.)
- Test specimen from compression moulded sheet at 23°C.- FRR values are statistical and calculated by dividing MFR values- Test specimen from compressed moulded sheet 23 C sheet 23 ºC - The data quoted are average values - The data quoted are average values
ASTM MethodUnitTypical ValueTest/CompositionISO1183g/cm30.957Density
28FRR 21.6/5ISO1167h5000 (4.5N/mm2)Hydrostatic Strength (80°c)ISO1133(g/10 min)6.2MFR190°/21.6ISO1133(g/10 min)0.22MFR190°/5
ISO179/1eAmJ/mm224Notched Impact (23°c)
39
JAM Petrochemical CompanyTechnical Catalogue 2018 39
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
Shear-Viscosity @ 190 °C
- On compression moulded according to ASTM D1928CProcessing ConditionsRecommended barrel tempratures range between 190 °C and 280 °C.
PE-100-B
1.00E+04
1.00E+05
1.00E+06
1.00E+02
1.00E+03
1.00E+04
1.00E+05
1.00E+00 1.00E+01 1.00E+02 1.00E+031.00E+04
TAU
ap 1
[Pa
];
ETAa
p 1
[Pa*
s];
ETAap 1 [Pa*s]; Ser.: 1; TAUap 1 [Pa]; Ser.: 1;
JAM Petrochemical CompanyTechnical Catalogue 201840
Product data sheet
HM-9450F (EX5) is blown film grade resin which is manufactured by suspension polymerization of ethylene monomer. HM-9450F (EX5) is a bi-model high density polyethylene with 1-Butene as co monomer.
- Test specimen from compression moulded sheet at 23°C.- FRR values are statistical and calculated by dividing MFR values.- Notch Impact Test specimen from compressed moulded sheet 23°C and The data quoted are average values
Density: 0.947-0.951 g/cm3HDPE: HM9450F (EX5) MFR 190/5: 0.23-0.33
CharacteristicProperties
• High molar mass film grade, good
stiffness and tenacity
Main Applications
• For blown films with paperlike
quality, sutable for counter bags,
carrier bags and wrapping films,
excellent processing.
Additives
• Antioxidant/Process stabilizer
• Lubricant (processing aid)/ acid
scavenge
HDPE made via Hostalen Process
HM9450F(EX5)
Material properties (This data are typical values and are not to be construed as product specifications.)
Test/Composition Typical Value Unit MethodDensity 0.949 g/cm3 ISO1183Fish Eye Note ≤3 note InternalFRR 21.6/5 29MFR 190°/21.6 8.0 g/10min ISO1133MFR190°/5 0.28 g/10min ISO1133
41
JAM Petrochemical CompanyTechnical Catalogue 2018 41
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
1.00E+04
1.00E+05
1.00E+06
1.00E+01
1.00E+02
1.00E+03
1.00E+04
1.00E+05
1.00E+00 1.00E+01 1.00E+02 1.00E+03 1.00E+04 1.00E+05
TAU
1 [P
a*s]
ETA
1 [P
a*s]
GAMMA 1 [1/s]
4
LLDPE Products
Low Density Polyethylene Unit Under the license of BASELL, JAM Petrochemical Company’s LLDPE Unit has been designed and established with TECNIMONT’s basic engineering and SPHERILENE technology. Able to produce 300,000 tons of products per year, JPC (LLDPE) Unit is one of the greatest polymer production units in Iran which enjoys the capacity of producing both high density and linear low density polyethylene. capacity of The guarantee of extruder in this unit is 42 to 48 tons per hour proportionate to grade type and the unit can produce more than 54 different grades for such varying applications as the following:FILM - INJECTION MOLDING -STRETCHED TAPE - MONOFILAMENT ROTOMOLDING - YARN - CAPS & CLOSURESThe products made by this unit can be utilized in various industries such as packaging industries, home appliances manufacture industries, textile industry, agricultural industry, and automobile manufacture industries.
JAM Petrochemical CompanyTechnical Catalogue 201844
Products Capacity of LLDPE plant
DensityMFR
(190°C/2.16 kg)
PROPERTY
GRADES g/l(g/10 min).UNITD 1505D 1238ASTM METHOD1700417066INTERNAL METHOD
1- LLDPE Butene
922 - 925918 ± 2923 ± 1923 ± 1918 ± 2
916 - 919
0.70 ± 0.10.95 ± 0.11.80 ± 0.20.95 ± 0.12.00 ± 0.23.00 ± 0.3
• Lamination• Liner• General Purpose• High Stiffness• Cast & general Purpose• Cast
235F71650122502/ AA/ 22502 KJ22501/ AA/ 22501 KJ1650216503
2- Terpolymer - HP-LLDPE SPECIALITY PRODUCTS
914 ± 2914 ± 2
914 - 917914 - 917914 ± 2915 ± 1912 ± 1910 ± 1921 ± 1920 ± 2
0.60 ± 0.100.6
0.75 ± 0.100.90 ± 0.100.95 ± 0.100.95 ± 0.102.00 ± 0.202.20 ± 0.202.50 ± 0.200.50 ± 0.10
• High Performance• Shrink• Easy Processability• Lamination• Superbutene• High Stiffness• General Purpose• Stretch cast• Bread bags• High performance
12XF612HF614ZF814XF912X0114X0111X0209X0220X0218XF5 N
3- Quattropolymer'' HP-LLDPE SPECIALTTY PRODUCTS (HP HEXENE TYPE)
918 - 921918 - 921914 ± 2916 ± 1
911 - 914915 ± 1911 ± 1
0.30 ± 0.050.55 ± 0.100.60 ± 0.100.60 ± 0.100.60 ± 0.101.00 ± 0.102.20 ± 0.20
• Shrink film, high perform.• High Stiffness/ Shrink• Liner• Heavy duty• Lamination high clarity• Thin film• High Pre-Stretch cast
18YF318YF512YF615YF611YF614Y0110Y02
4- VLDPE (butene) film grades SPECLALITY GRADES
911 ± 1911 ± 1
2.50 ± 0.302.50 ± 0.30
• Lamination• Cast- Co-extrusion(*)
1050110502
(*) This product is used as adhesive layer in a multilayer co-extruded film.
Available
Available
Available
Innovations in the products of JAM Petrochemical Company are shown with the this symbol.
JAM Petrochemical CompanyTechnical Catalogue 2018 45
Products Capacity of LLDPE plant
DensityMFR
(190°C/2.16 kg)
PROPERTY
GRADES g/l(g/10 min).UNITD 1505D 1238ASTM METHOD1700417066INTERNAL METHOD
5- HP-VLDPE SPECIALITY PRODUCTS
902 ± 1903 ± 1
0.90 ± 0.101.80 ± 0.20
• Co-extrusion• Geomembranes, Bumpers, Soft Nets
01X0102X026- HDPE - Medium MWD - Stretched
954 ± 1942 ± 1953 ± 1950 ± 2
0.80 ± 0.100.50 ± 0.100.70 ± 0.101.00 ± 0.10
• Monofilament• Raffia (Textile grade)• Monofilament, high tenacity• Monofilament
Jamlene HD-5000s424F5534F750401
7- HP-HDPE (@) SPECIALITY PRODUCTS
936 ± 1943 ± 1941 ± 1
0.60 ± 0.101.00 ± 0.101.20 ± 0.10
• Raffia for ropes• Monofilament• Cast flat yarn (Raffia)
36XF643X0141X01
8- HDPE Narrow MWD - Homopolymer injection moulding grades
958 ± 2958 ± 2958 ± 2958 ± 2958 ± 2
5.50 ± 1.007.50 ± 1.0011.00 ± 2.0018.00 ± 2.0035.00 ± 5.00
• Crates• Crates• Houseware• Fast cycle• Thin walled
60505 / 60505 UV60507 / 60507 UV60511 / 60511 UV6051860535
9- HDPE Narrow MWD - Copolymer injection moulding grades
952 ± 2952 ± 2952 ± 2952 ± 2952 ± 2952 ± 2952 ± 2
0.90 ± 0.102.00 ± 0.102.00 ± 0.105.00 ± 1.0011.00 ± 2.0018.00 ± 2.0028.00 ± 4.00
• Caps and closures (CSD)• Caps and closures (Mineral water, CSD)• Caps and closures (CSD)• Containers• Houseware• Houseware, High fluidity• Caps, Thin walled
CC 52501CC 52502CC 52502SU52505 / 52505 UV52511 / 52611 UV5251852528
10- LLDPE (butene) Injection moulding grades
922 ± 1922 ± 1925 ± 1926 ± 1
5.00 ± 1.0016.00 ± 2.0025.00 ± 3.0060.00 ± 5.00
• General purpose• General purpose• Lids• Fast Cycle
20505205162552526560
Available
Available
Available
Available
Available
Available
Available
Available
Available
Available
JAM Petrochemical CompanyTechnical Catalogue 201846
Products Capacity of LLDPE plant
DensityMFR(190°C/2.16 kg)PROPERTY
GRADES g/l(g/10 min).UNITD 1505D 1238ASTM METHOD1700417066INTERNAL METHOD
11- LLDPE (butene) Extrusion coating
923 ± 17.00 ± 1.00• Extrusion coating23507
12- LLDPE Rotomoulding
932 ± 1930 ± 1938 ± 2
932
4.00 ±1.005.00 ± 1.004.00 ± 1.00
5
• Rotomoulding, high-ESCR• Rotomoulding, high-ESCR• Rotomoulding, high-ESCR• Rotomoulding, high-ESCR
32604 UV30505 UV38504 UV32505 UV
13- HP LLDPE SPECIALTTY PRODUCTS
930 ± 14.00 ± 1.00• Rotomoutding & Stiff Cast30Y04
14- BWMD HDPE for Blow moulding
952952952
0.120.250.25
• Blow moulding containers, high impact• Blow moulding small containers, high ESCR• Blow moulding small containers
526F1BX(*)
526F2BX524F2(*)
15- BWMD HDPE for pipes
9480.2(1)• Pipes486H2(*)
16- BWMD HDPE for Blown film
952948952948
0.15(1)
0.25(1)
0.15(1)
0.25(1)
• Blow film, high Stiffness• Blow film, high mechanicals• Blow film, high Stiffness• Blow film, general purposes
526H1(*)
486H2(*)
524H1FX(*)
484H2(*)
(*) Grade under final development, to be Industrialised.
(1) Melt Flow rate (190° C/5kg).
Available
Available
Innovations in the products of JAM Petrochemical Company are shown with the this symbol.
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 47
22502 is a LLDPE blown film grade designed for applications requiring ease of processing and good optical properties even at low extrusion temperature. This resin is well suited for blending with LDPE and for general purpose uses, including agricultural applications.
Density: 0.922-0.924LLDPE: 22502AA/22502KJ MFI: 1.6-2
CharacteristicProperties
• ease of processing• good optical properties• low extrusion temperature• suited for blending with LDPE
Main Applications
• Blown film grade• General purpose• agricultural applications.
LL22502AALL22502KJ
Material properties (This data are typical values and are not to be construed as product specifications.)
LLDPE made via Spherilene Gas-Phase Technology
ASTM MethodTypical ValueUnitResin PropertiesD12381.80(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.9220g/mlDensity
Film properties @D170967(g)Dart ImpactD1922127/332MD/TD(g)Elmendorf TearD88212/12MD/TD(MPa)Tensile Strength at yieldD88237/32MD/TD(MPa)Tensile Strength at breakD882783/888MD/TD(%)Ultimate elongation
D100348(%)HazeD245710Gloss 45°
@ 25 micron film obtained on Collin 25, B.u.R. 2.5: 1, Temp. profile 155 190°C.Recommended processing conditions
190-230(°C)Melt Temperature2.0-3.0Blow up ratio2.0-2.5(mm)Die Gap15-150(micron)Thickness
Additives
• 22502AA:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)• 22502KJ:•Thermal Antioxidant (Process Stabilizer)• Antiblocking Agent• Slip Agent• Catalyst neutralizer (acid scavenger, lubricant)
JAM Petrochemical CompanyTechnical Catalogue 201848
Product data sheet
22501 is a LLDPE blown film grade designed for applications requiring good optical properties even at low extrusion temperature. This resin combines ease of processing with low gels and it is well suited for blending with LDPE and for general purpose applications.
Density: 0.922-0.924 LLDPE: 22501AA/22501KJ MFI: 0.85-1.05
CharacteristicProperties
• High stiffness• good optical properties• low extrusion temperature• ease of processing• low gels• suited for blending with LDPE
Main Applications
• Blown film grade• General Purpose opplications
Additives
• 22501AA:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)• 22501KJ:•Thermal Antioxidant (Process Stabilizer)• Antiblocking Agent• Slip Agent• Catalyst neutralizer (acid scavenger, lubricant)
LL22501AALL22501KJ
Material properties (This data are typical values and are not to be construed as product specifications.)
LLDPE made via Spherilene Gas-Phase Technology
ASTM MethodTypical ValueUnitResin PropertiesD12380.95(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.9230g/mlDensity
Film properties @D170970(g)Dart ImpactD1922105/436MD/TD(g)Elmendorf TearD88211/12MD/TD(MPa)Tensile Strength at yieldD88241/31MD/TD(MPa)Tensile Strength at breakD882648/780MD/TD(%)Ultimate elongation
D100348(%)HazeD245710Gloss 45°
@ 25 micron film obtained on Collin 25, B.u.R. 2.5: 1, Temp. profile 155 190°C.Recommended processing conditions
190-230(°C)Melt Temperature2.0-3.0Blow up ratio2.0-2.5(mm)Die Gap15-150(micron)Thickness
49
JAM Petrochemical CompanyTechnical Catalogue 2018 49
Shear-Viscosity @ 190 °C
- On compression moulded according to ASTM D1928CProcessing ConditionsRecommended barrel tempratures range between 190 °C and 280 °C.
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
JAM Petrochemical CompanyTechnical Catalogue 201850
Product data sheet
HP-LL18XF5 N is a termopolymer of ethylene, propylene and butene-1 for high Strength application especially heavy duty shipping sacks, ice bag, frozen food bags, potato bags and agriculture films which have good sealability and excellent puncture resistance. Goods produced from this grade have outstanding toughness, excellent puncture resistance, good heat sealing behavior and excellent machinability on conversion lines. HP-LLDPE's process is easier than conventional LLDPEs and have low gel. HP-LL18XF5 N is a grade without slip additives.
Density: 0.918-0.922HP-LLDPE: HP-LL18XF5N MFI: 0.4-0.6
CharacteristicProperties
• Exellent punctuer resistance.
• Exellent machinability on conver-
sion lines.
Main Applications
• T-bags and other bags, Food Packag-
ing for frozen products, Agricultural
film, Heat seal film, Food Packaging
Additives
•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)• Antiblocking Agent
HPLL18XF5N
Material properties (This data are typical values and are not to be construed as product specifications.)
Test MethodTypical Value UnitResin PropertiesD12380.5 (g/10 min)Melt Index (190°C/ 2.16Kg)D15050.918 g/cm³Density
Film Properties @ D 1709125 g Dart ImpactD1525127 °CVicat Softening PointD638 11/10(MD/TD)MpaTensile Strength at YieldD63840/35(MD/TD)MpaTensile Strength at BreakD638600/750(MD/TD)% Ultimate Elongation
D1922240/400(MD/TD)gElmendorf TearD100330 %HazeD245725 Gloss 45°
@ on 25 micron film obtained on Collin 25, B.u.R 2.5: 1, Temp. profile 155 190°C: melt 200°C
HP-LLDPE made via Spherilene Gas-Phase Technology
51
JAM Petrochemical CompanyTechnical Catalogue 2018 51
Shear-Viscosity @ 190 °C
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
JAM Petrochemical CompanyTechnical Catalogue 201852
Product data sheet
Jamlene: HD5000S
Typical Applications
• Fishing net, Rope, Agricultural net, Tar-
paulin, Woven sack.
HDPE for Monofilament
HD5000S
Resin Properties Unit Value Test MethodMelt Index g/10 min 0.8 D1238Density g/cm³ 0.954 D1505Thermal Properties Unit Value Test MethodVicat Softening Point °C 125 D1525Molded Properties Unit Value Test MethodFlectural Modulus Mpa 1100 D790Tensile Strength at Yield Mpa 24 D790Tensile Strength at Break Mpa 39 D638H.D.T °C 75 D648Notched Izod Impact @ 23 °C J/m 400 D256/A
- On compression molded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range is between 160 °C and 190 °C
Density: 0.954 ± 1 MFI: 0.8 ± 0.1
HD-5000S is a HDPE grade specially designed for monofilament applications, which combines good processability with high tenacity. This grade has good balance of mechanical strength and high production rates. HD-5000S is also well suited for multiply applications, like ropes and stretched filaments.
CharacteristicProperties
good processability with high
tenacity, good balance of
mechanical strength and high
production rates
Additives
Antioxidants/Acid scavengerAntiblock/Processing aid
53
JAM Petrochemical CompanyTechnical Catalogue 2018 53
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
HD-5000S
1.00E+04
1.00E+05
1.00E+06
1.00E+02
1.00E+03
1.00E+04
1.00E+00 1.00E+01 1.00E+02 1.00E+03
1.00E+04
TAU
ap 1
[Pa
];
ETAa
p 1
[Pa*
s];
ETAap 1 [Pa*s]; Ser.: 1; TAUap 1 [Pa]; Ser.: 1;
JAM Petrochemical CompanyTechnical Catalogue 201854
Product data sheet
60505 is a HDPE injection molding grade which combines high stiffness with good physical properties.This resin is well suited for crates and toys applications.
Density: 0.956-0.960HDPE: 60505/60505UV MFI: 4.5-6.5
CharacteristicProperties
• High stiffness with good physical properties.
Main Applications
• injection molding grade
• Crates
• toys applications
Additives• 60505:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)• 60505UV:• Catalyst neutralizer (acid scavenger, lubricant)• UV Stabilizer•Thermal Antioxidant
(Process Stabilizer)
HD60505HD60505UV
Material properties (This data are typical values and are not to be construed as product specifications.)
HDPE made via Spherilene Gas-Phase Technology
ASTM MethodTypical ValueUnitResin PropertiesD12385.5(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.9570g/mlDensity
Physical properties @D7901460(MPa)Flexural modulus
D256/A30(J/m)Notched Izod impact at 23°CD1525125(°C)Vicat softening point
@ on compression moulded specimen obtained according to ASTM D 1928°CFabrication conditions for injection mouldingRecommended barrel temperatures range between 190 and 280°C
55
JAM Petrochemical CompanyTechnical Catalogue 2018 55
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
HD-60505
1.00E+04
1.00E+05
1.00E+06
1.00E+02
1.00E+03
1.00E+04
1.00E+00 1.00E+01 1.00E+02 1.00E+031.00E+04
TAU
ap 1
[Pa
];
ETAa
p 1
[Pa*
s];
time
ETAap 1 [Pa*s]; Ser.: 1; TAUap 1 [Pa]; Ser.: 1;
JAM Petrochemical CompanyTechnical Catalogue 201856
Product data sheet
60507 is a HDPE homopolymer which is manufactured in gas phase process for injection molding grade which combines good flowability with balanced physical properties. This resin is well suited for general purpose application requiring high stiffness.
Density: 0.956-0.960HDPE: HD-60507/HD-60507UV MFI: 6.5-8.5
CharacteristicProperties
• Good flowability with balanced
phisycal properties.
Main Applications
• Crates
Injection molding grade
Additives
• HD-60507:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)• HD-60507UV:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)• UV Stabilizer
HD60507HD60507UV
Material properties (This data are typical values and are not to be construed as product specifications.)
HDPE made via Spherilene Gas-Phase Technology
Test MethodTypical ValueUnitResin PropertiesD12387.5(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.958g/mlDensity
Test MethodTypical ValueUnit Resin Properties @D1525126.5(°C)Vicat Softening Point
Test MethodTypical ValueUnitMoulded Properties @D7901450(MPa)Flexural Modulus
D256/A24(J/m)Notched Izod Impact @ 23 °C
57
JAM Petrochemical CompanyTechnical Catalogue 2018 57
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
HD-60507
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+02
1.00E+03
1.00E+04
1.00E+00 1.00E+01 1.00E+02 1.00E+031.00E+04
TAU
ap 1
[Pa
];
ETAa
p 1
[Pa*
s];
ETAap 1 [Pa*s]; Ser.: 1; TAUap 1 [Pa]; Ser.: 1;
JAM Petrochemical CompanyTechnical Catalogue 201858
Product data sheet
HDPE: CC52501
Typical Applications
• Caps and closures for beverage bottles of
sparkling water, hot-filled and carbonated
soft drinks.
Caps and closures (CSD)
CC52501
Resin Properties Unit Value Test MethodMelt Index g/10 min 0.9 D1238Density g/cm³ 0.952 D1505Thermal Properties Unit Value Test MethodVicat Softening Point °C 123 D1525Molded Properties Unit Value Test MethodFlectural Modulus Mpa 800 D790Tensile Strength at Yield Mpa 25 D790Tensile Strength at Break Mpa 36 D638H.D.T °C 78 D648Notched Izod Impact @ 23 °C J/m 80 D256/A
CC52501 is a Narrow MWD HDPE specially designed for beverage bottles of sparkling water, hot-filled and carbonated soft drinks. This grade has excellent organoleptic properties which prevent unpleasant odor and taste from cap or closure to transfer to water. It has good gas permeability characteristics, superior processability and excellent mechanical strength. HDPE CC52501 does not contain slip agent.
- On compression molded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range is between 160 °C and 190 °C
CharacteristicProperties
Narrow MWD HDPE, excellent
environmental stress crack
resistance and organoleptic
property, good gas permeability
characteristics
Additives
Antioxidants/Acid scavenger
Density: 0.952 ± 2 MFI: 0.9 ± 0.1
59
JAM Petrochemical CompanyTechnical Catalogue 2018 59
Storage and HandlingPolyethylene products (in pelletized or
powder form) should not be stored in
direct sunshine and/or heat radiation. The
Storage area should be dry and preferably
don’t exceed 50 °C. JPC would not
responsible about quality diminishing such
as color change, bad smell or est. which
caused by bad storage conditions. It is
better to process PE resin within 6 months
after delivery.
The technical information sug-gested uses and application pre-sented are belived to be accurated and reliable, however JPC makes no warranties either express or implied concerning the information herein or the use of our materials.
JAM Petrochemical CompanyTechnical Catalogue 201860
Product data sheet
HDPE: CC52502
Typical Applications
• Caps and closures for mineral water bot-
tles,Caps for sparkling water and carbonat-
ed soft drinks, beverage caps.
Caps and closures (Mineral water, CSD)
CC52502
Resin Properties Unit Value Test MethodMelt Index g/10 min 2 D1238Density g/cm³ 0.952 D1505Thermal Properties Unit Value Test MethodVicat Softening Point °C 124 D1525Molded Properties Unit Value Test MethodFlectural Modulus Mpa 1000 D790Tensile Strength at Yield Mpa 25 D790Tensile Strength at Break Mpa 38 D638H.D.T °C 78 D648Notched Izod Impact @ 23 °C J/m 180 D256/A
CC52502 is a Narrow MWD HDPE specially designed for mineral water bottles and beverage caps. This grade has excellent organoleptic properties which prevent unpleasant odor and taste from cap or closure to transfer to water. It has good gas permeability characteristics, superior processability and excellent mechanical strength. HDPE CC52502 does not contain slip agent.
- On compression molded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range is between 160 °C and 190 °C
CharacteristicProperties
Narrow MWD HDPE, excellent
organoleptic property, superior
processability and excellent
mechanical strength, good gas
permeability characteristics
Additives
Antioxidants/Acid scavenger
Density: 0.952 ± 2 MFI: 2 ± 0.1
61
JAM Petrochemical CompanyTechnical Catalogue 2018 61
Storage and HandlingPolyethylene products (in pelletized or
powder form) should not be stored in
direct sunshine and/or heat radiation. The
Storage area should be dry and preferably
don’t exceed 50 °C. JPC would not
responsible about quality diminishing such
as color change, bad smell or est. which
caused by bad storage conditions. It is
better to process PE resin within 6 months
after delivery.
The technical information sug-gested uses and application pre-sented are belived to be accurated and reliable, however JPC makes no warranties either express or implied concerning the information herein or the use of our materials.
JAM Petrochemical CompanyTechnical Catalogue 201862
Product data sheet
HDPE: CC52501
Typical Applications
• Caps and closures for mineral water
bottles, Caps for sparkling water and car-
bonated soft drinks, beverage caps.
Caps and closures (CSD)
CC52502SU
Resin Properties Unit Value Test MethodMelt Index g/10 min 2 D1238Density g/cm³ 0.952 D1505Thermal Properties Unit Value Test MethodVicat Softening Point °C 124 D1525Molded Properties Unit Value Test MethodFlectural Modulus Mpa 1000 D790Tensile Strength at Yield Mpa 25 D790Tensile Strength at Break Mpa 38 D638H.D.T °C 78 D648Notched Izod Impact @ 23 °C J/m 180 D256/A
CC52502 is a Narrow MWD HDPE specially designed for mineral water bottles and beverage caps. This grade has excellent organoleptic properties which prevent unpleasant odor and taste from cap or closure to transfer to water. It has good gas permeability characteristics, superior processability and excellent mechanical strength. HDPE CC52502SU does contain slip agent and stabilized against UV light.
- On compression molded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range is between 160 °C and 190 °C
CharacteristicProperties
Narrow MWD HDPE, excellent
organoleptic property, superior
processability and excellent
mechanical strength, good gas
permeability characteristics
Additives
Antioxidants/Acid scavenger
UV stabilizer/Slip agent
Density: 0.952 ± 2 MFI: 2 ± 0.1
63
JAM Petrochemical CompanyTechnical Catalogue 2018 63
Storage and HandlingPolyethylene products (in pelletized or
powder form) should not be stored in
direct sunshine and/or heat radiation. The
Storage area should be dry and preferably
don’t exceed 50 °C. JPC would not
responsible about quality diminishing such
as color change, bad smell or est. which
caused by bad storage conditions. It is
better to process PE resin within 6 months
after delivery.
The technical information sug-gested uses and application pre-sented are belived to be accurated and reliable, however JPC makes no warranties either express or implied concerning the information herein or the use of our materials.
JAM Petrochemical CompanyTechnical Catalogue 201864
Product data sheet
52505 is a HDPE copolymer which is manufactured in gas phase process. This grade is an injection molding grade for applications requiring a good physical property even at low temperatures, like pails, containers and technical moldings.
Density: 0.950-0.954HDPE: 52505/52505UV MFI: 4-6
CharacteristicProperties
• Good physical property even at
low temperatures.
Main Applications
• Containers.
HD52505HD52505UV
Material properties (This data are typical values and are not to be construed as product specifications.)
Additives
HD-52505:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)HD-52505 UV:•Thermal Antioxidant (Process Stabilizer)• Antiblocking Agent• Catalyst neutralizer (acid scavenger, lubricant)• UV Stabilizer
HDPE made via Spherilene Gas-Phase Technology
Test MethodTypical ValueUnitResin PropertiesD12385(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.952g/mlDensity
Test MethodTypical ValueUnit Thermal Properties @D1525124(°C)Vicat Softening Point
Test MethodTypical ValueUnitMoulded Properties @D7901200(MPa)Flexural ModulusD63827(MPa)Tensile Strength at yieldD63813(MPa)Tensile Strength at breakD64867(°C)H.D.T
D256/A29(J/m)Notched Izod Impact @ 23 °C
65
JAM Petrochemical CompanyTechnical Catalogue 2018 65
Shear-Viscosity @ 190 °C
@ On compression moulded according to ASTM D1928CProcessing Conditions:Recommended barrel tempratures range between 190 °C and 280 °C.
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
JAM Petrochemical CompanyTechnical Catalogue 201866
Product data sheet
52511 is a HDPE copolymer injection molding grade for applications requiring a good balance between physical properties and flowability, like housewares and toys.
Density: 0.950-0.954HDPE: 52511/52511UV MFI: 9-13
CharacteristicProperties
• Good balance between physical properties and flowability,
Main Applications
• injection molding grade
• Houseware
HD52511HD52511UV
Material properties (This data are typical values and are not to be construed as product specifications.)
Additives
52511:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)52511 UV:•Thermal Antioxidant (Process Stabilizer)• Antiblocking Agent• Catalyst neutralizer (acid scavenger, lubricant)• UV Stabilizer
HDPE made via Spherilene Gas-Phase Technology
ASTM MethodTypical ValueUnitResin PropertiesD123811(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.9520g/mlDensity
Physical properties @D7091200(MPa)Flexural modulus
D256/A22(J/m)Notched Izod impact at 23°CD1525122(°C)Vicat softening point
@ on compression moulded specimen obtained according to ASTM D 1928°CFabrication conditions for injection mouldingRecommended barrel temperatures range between 190 and 280°C
67
JAM Petrochemical CompanyTechnical Catalogue 2018 67
Shear-Viscosity @ T190 °C
@ On compression moulded according to ASTM D 1928 C
Processing Conditions:Melt Temperature (°C): 190 -280
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
JAM Petrochemical CompanyTechnical Catalogue 201868
Product data sheet
52518 is a HDPE copolymer for Injection Moulding for applications requiring a good balance between easy of processability and flowability and mechanical properties.
Density: 0.950-0.954HDPE: HD-52518 MFI: 16-20
CharacteristicProperties
• Good balance between easy of
processability and flowability
Main Applications
• Housewares
• High fluidity
• Injection moulding grade
Additives
•Thermal Antioxidant (Process
Stabilizer)
• Catalyst neutralizer (acid
scavenger, lubricant)
HD52518
Material properties (This data are typical values and are not to be construed as product specifications.)
Test MethodTypical ValueUnitResin PropertiesD123818(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.952g/mlDensity
Test MethodTypical ValueUnit Thermal Properties @D1525121(°C)Vicat Softening Point
Test MethodTypical ValueUnitMoulded Properties @D7901200(MPa)Flexural Modulus
D256/A19(J/m)Notched Izod Impact @ 23 °C@ on compression moulded specimen, according to ASTM D 1928°C
HDPE made via Spherilene Gas-Phase Technology
69
JAM Petrochemical CompanyTechnical Catalogue 2018 69
Shear-Viscosity @ 190 °C
@ On compression moulded according to ASTM D1928CProcessing Conditions:Recommended barrel tempratures range between 190 °C and 280 °C.
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handling and Health SafetyMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
JAM Petrochemical CompanyTechnical Catalogue 201870
Product data sheet
32604 is a LLDPE for rotomolding which manufactured by gas phase process. This grade is suitable for all applications which need a good balance among moldability and mechanical properties together with an exceptional stress cracking resistance.
Density: 0.932LLDPE: LL-32604/UV MFI: 4
Features
• Exellent ESCR.
Applications
• High ESCR rotomolded items
Chemical containers.
Additives
• LL-32604:Thermal Antioxidant• LL-32604UV:Thermal AntioxidantUV Stabilizer
LLDPE made via Spherilene Process
LL32604LL32604 UV
Material properties (This data are typical values and are not to be construed as product specifications.)
Test MethodTypical ValueUnitResin Properties
D12384g/10 minMelt Index
D15050.932g/cm³Density
Test MethodTypical ValueUnitPhysical Properties
D7901350MpaFlectural Modulus
D256/ANBJ/mNotched Izod Impact @ 23 °C
D1693>1000hE.S.C.R
71
JAM Petrochemical CompanyTechnical Catalogue 2018 71
Shear-Viscosity @ 190 °C
- On compression molded according to ASTM D1928CProcessing ConditionsRecommended barrel tempratures range between 190 °C and 280 °C.
The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.
Handellling and Health SafetysMolten polymers could be injured skin or eye so safety
glasses and appropriate gloves are suggested to prevent
possible thermal injuries. Also appropriate ventilation is
suggested in working by melt polymer.
Accumulation of fines or dust particles that are in this grade
is not suitable because of explosion hazard probability.
So adequated filters and grounding exists at all time are
recommended.
Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ultraviolet cause a change in the material properties.The Storage area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. . JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.
packagingJam Polymers Polyolefin resins are supplied in pllet form packed in 25kg bags. Alternative packaging modes are avalable for selected grades.
JAM Petrochemical CompanyTechnical Catalogue 201872
Product data sheet
MD-38504 is a UV stabilized linear medium density polyethylenee grade with a narrow molecular weight distribution. It is suitable for rotational molding and some injection molding application such as technical parts and closures. Characteristics include: good impact Strength, excellent external and internal surface finish, and is UV stabilized.
Density: 0.936-0.940MDPE: 38504 UV MFI: 3-5
CharacteristicProperties
• Good impact Strength
• High ESCR
Main Applications
• Rotomolding
Additives
•Thermal Antioxidant (Pro-
cess Stabilizer)
• Catalyst neutralizer (acid
scavenger, lubricant)
• UV Stabilizer
MD38504UV
Material properties (This data are typical values and are not to be construed as product specifications.)
ASTM MethodTypical ValueUnitResin PropertiesD12384(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.938g/mlDensity
Physical properties @D790650(MPa)Flexural ModulusD63815(MPa)Tensile Strength at yieldD638800(%)Tensile Strength at breakD25625KJ/m2Charpy Unnotched impact Strength
D1525115(°C)Vicat Softening TemperatureD224060Shore DDurometer Hardness
@ on compression moulded specimen obtained according to ASTM D 1928°C
MDPE made via Spherilene Gas-Phase Technology
73
JAM Petrochemical CompanyTechnical Catalogue 2018 73
Storage and HandlingPolyethylene products (in pelletized or
powder form) should not be stored in
direct sunshine and/or heat radiation. The
Storage area should be dry and preferably
don’t exceed 50 °C. JPC would not
responsible about quality diminishing such
as color change, bad smell or est. which
caused by bad storage conditions. It is
better to process PE resin within 6 months
after delivery.
The technical information sug-gested uses and application pre-sented are belived to be accurated and reliable, however JPC makes no warranties either express or implied concerning the information herein or the use of our materials.
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201874
60511 is a HDPE injection molding grade which combines excellent flowability with high stiffness.This resin is well suited for housewares and toys applications.
Density: 0.956-0.960HDPE: 60511/60511UV MFI: 9-13
CharacteristicProperties
• Excellent flowability with high stiffness.
Main Applications
• injection molding grade
• Houseware
• toys
Additives60511:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)60511UV:• Catalyst neutralizer (acid scavenger, lubricant)• UV Stabilizer•Thermal Antioxidant (Process Stabilizer)
HD60511HD60511UV
Material properties (This data are typical values and are not to be construed as product specifications.)
HDPE made via Spherilene Gas-Phase Technology
ASTM MethodTypical ValueUnitResin PropertiesD123811(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.960g/mlDensity
Physical properties @D7901450(MPa)Flexural modulus
D256/A21(J/m)Notched Izod impact at 23°CD1525125(°C)Vicat softening point
@ on compression moulded specimen obtained according to ASTM D 1928°CFabrication conditions for injection mouldingRecommended barrel temperatures range between 190 and 280°C
5
PolypropyleneProductsPolypropylene productsJAM Polypropylene Co. (JPPC) was established in 2004 in Pars Free Energy Zone in Asaluyeh on the northern shores of the Persian Gulf. Thus, Jam Polypropylene Co. is in a unique position to contribute to the global petrochemical downstream markets while respecting all quality standards. To achieve this goal, Jam Polypropylene Co. enjoys some significant logistic advantages including availability of low-cost, gas-based feedstock, prominent production capacity, strategic location and proximity to port Asaluyeh that expedites the export operation and timely delivery of products. JPPC has acquired the unique state-of-the art Spheripol technology from LyondellBasell, as the world leading technology for the production of a very wide range of polypropylene (PP) grades.
MissionWe are committed to create sustainable value for all beneficiaries through steady development of Polypropylene production and sales based on innovation, products diversification and ceaseless quality improvement while complying with regulations.
JPPC is capable of producing a wide range of Polypropylene grades under the name of “Jampilen” with premium quality.
• HomopolymerThermoformingExtrusion (film, BOPP, cast, yarn, monofilament, sheet, CF, BCF, staple, nonwoven)Injection molding
• Random copolymer & TerpolymerExtrusion (film, sheet, BOPP, pipe)Injection molding
• Heterophasic copolymerInjection moldingThermoformingExtrusion (sheet, pipe, profile)Blow molding
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201878
″Jampilen HP525J″ is a medium flow homopolymer with bimodal molecular weight distribution and good clarity intended for BOPP films. The product is suitable for metallizable film, both as monolayer and in coextruded structures. It contains a standard processing stabilisation but does not contain any slip, antiblocking agents and is calcium stearate free. ″Jampilen HP525J″ offers good optical properties, easy processing and very stable film profile. Typical applications are BOPP packaging films and Solid Phase Thermoforming sheets.″Jampilen HP525J″ is suitable for food contact
Density: 0.9Jampilen HP525J MFI: 3
Characteristic Properties
• Good optical properties, easy processing and very stable film profile
Main Applications
• High quality packaging film for food
• Lamination to other films
• Metalizable film
• Medical packaging
• Thermoformed food containers
• BOPP Film
Additives
• Antioxidant package
HP525J
MethodUnitValueTypical Properties Physical
ASTM D1238g/10min3.0Melt Flow Rate (230 oC, 2.16kg)ASTM D1505g/cm30.9Density
Mechanical
ASTM D790MPa1400Flexural ModulusASTM D638MPa32Tensile Strength at YieldASTM D638%9Tensile Elongation at Yield
ASTM D256J/m55Izod Impact Strength(notched)at 23oC
Thermal
ASTM D1525oC152Vicat softening point (10N)ASTM D648oC84H.D.T. (0.46 MPa)
ASTM D3012hours500Accelerated oven ageing in air at 150oC
Optical
ASTM D1003%0.5Haze (20μm)
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 79
″Jampilen HP550J″ is a polypropylene homopolymer particularly suitable for the extrusion of sheet for thermoforming, film yarn and monofilament. This grade combines suitable processability with good mechanical properties.″Jampilen HP550J″ is designed for the production of films that can be converted into stretched tapes for weaving applications. Textile film yarns with a denier count of not more than 1100 to 1200 are used for the production of carpet backings, bags, industrial fabrics, mats and artificial grass. Film yarn with a denier count ranging from 3000 to 28000 is used for baler twines, packaging twines and ropes.″Jampilen HP550J″ is suitable for food contact.
Density: 0.9Jampilen HP550J MFI: 3.2
Characteristic Properties
• Good processability, good mechanical properties
Main Applications
• Stiff sheet for high quality thermoformings such as vending cups, packaging for dairy products and trays for fruit, biscuits and chocolates• Film yarn, raffia, tapes, strapping• Carpet backings, bags, industrial fabrics, mats• Artificial grass• Baler twines, packaging twines and ropes• Brush and broom filling and technical applications• Nets for various purposes
Additives
• Antioxidant package
HP550J
MethodUnitValueTypical Properties Physical
ASTM D1238g/10min3.2Melt Flow Rate (230 oC, 2.16kg)ASTM D1505g/cm30.9Density
Mechanical
ASTM D790MPa1400Flexural ModulusASTM D638MPa32Tensile Strength at YieldASTM D638%9Tensile Elongation at Yield
ASTM D256J/m50Izod Impact Strength(notched)at 23oC
Thermal
ASTM D1525oC152Vicat softening point (10N)ASTM D648oC84H.D.T. (0.46 MPa)
ASTM D3012hours360Accelerated oven ageing in air at 150oC
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201880
Jampilen HP510L″ is a polypropylene homopolymer with good flow properties and is particularly suitable for the extrusion of film yarn, monofilament, cast film and sheet.
Density: 0.9Jampilen HP510L MFI: 6
Characteristic Properties
• Outstanding processability, Good mechanical properties
Main Applications
• Fiber extrusion (Sheet, film yarn,
monofilament), Cast film; Baler
twines, packaging twines and ropes;
Brush and broom filling and technical
applications; Coextruded film for
packaging; Thin sheet for stationery
folders; Sheet for thermoforming;
Gunny sacks
Additives
• Antioxidant package
HP510L
MethodUnitValueTypical Properties Physical
ASTM D1238g/10min6.0Melt Flow Rate (230 oC, 2.16kg)ASTM D1505g/cm30.9Density
Mechanical
ASTM D790MPa1400Flexural ModulusASTM D638MPa32Tensile Strength at YieldASTM D638%8Tensile Elongation at Yield
ASTM D256J/m40Izod Impact Strength(notched)at 23oC
Thermal
ASTM D1525oC152Vicat softening point (10N)ASTM D648oC84H.D.T. (0.46 MPa)
ASTM D3012hours360Accelerated oven ageing in air at 150oC
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 81
″Jampilen HP552R″ is a high melt flow homopolymer for the production of CF, BCF and fine denier staple fibers at medium to high spinning speeds and exhibits excellent antigasfading properties.″Jampilen HP552R″ is suitable for nonwoven fabrics for diapers, medical-sanitary applications and wipes. Another typical application is high tenacity continuous filament for straps for backpacks, sport bags, bulk bags and safety belts. Continuous filament with medium tenacity is used for upholstery and sportswear. ″Jampilen HP552R″ is also suited for the production of bulked continuous filament for carpets.″Jampilen HP552R″ is suitable for food contact.
Density: 0.9Jampilen HP552R MFI: 25
Characteristic Properties
• High melt flow; Excellent antigas-
fading properties; Good processa-
bility
Main Applications
• Wipes and tissues• Straps for backpacks, sport bags, bulk bags and for safety belts• Upholstery and sportswear• Bulk continuous filament for carpets• Nonwoven staple fiber• Injection molded articles, housewares, etc
Additives
• Antioxidant package
HP552R
MethodUnitValueTypical Properties Physical
ASTM D1238g/10min25Melt Flow Rate (230 oC, 2.16kg)ASTM D1505g/cm30.9Density
Mechanical
ASTM D790MPa1400Flexural ModulusASTM D638MPa32Tensile Strength at YieldASTM D638%8Tensile Elongation at Yield
ASTM D256J/m30Izod Impact Strength(notched)at 23oC
Thermal
ASTM D1525oC152Vicat softening point (10N)ASTM D648oC84H.D.T. (0.46 MPa)
ASTM D3012hours150Accelerated oven ageing in air at 150oC
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201882
″Jampilen HP564S″ is a high melt flow rate homopolymer with a narrow molecular weight distribution for the high speed production of low denier continuous filament for spunbonded, nonwoven fabrics with an excellent balance of mechanical properties and softness. This grade is formulated with an anti-gasfading stabilization package and characterized by consistent high speed and low nonwoven weights. The major applications for spunbonded fabrics made of ″Jampilen HP564S″ are diapers, medical and sanitary tissues, protective fabrics for agricultural, industrial and medical applications, backings and linings for the furniture and carpet industries. This grade can also be used for the production of partially oriented yarn and bulked continuous filament. ″Jampilen HP564S″ is suitable for food contact.
Density: 0.9Jampilen HP564S MFI: 42
Characteristic Properties
• High melt flow; Narrow molecular weight distribution; Easy processability; Gasfading resistant
Main Applications
• Spunbonded, nonwoven fabrics• Fabrics for diapers, feminine care, medical and sanitary tissues• Protective fabrics for agricultural, industrial and medical applications• Backings and linings for the furni-ture and carpet industries• Oriented yarn and bulked continu-ous filament• Wipe and Tissues
Additives
• Antioxidant package,
Antistatic agent
HP564S
MethodUnitValueTypical Properties Physical
ASTM D1238g/10min42Melt Flow Rate (230 oC, 2.16kg)ASTM D1505g/cm30.9Density
Mechanical
ASTM D790MPa1400Flexural ModulusASTM D638MPa32Tensile Strength at YieldASTM D638%8Tensile Elongation at Yield
ASTM D256J/m30Izod Impact Strength(notched)at 23oC
Thermal
ASTM D1525oC152Vicat softening point (10N)ASTM D648oC84H.D.T. (0.46 MPa)
ASTM D3012hours360Accelerated oven ageing in air at 150oC
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 83
″Jampilen EP440G″ is a nucleated heterophasic copolymer especially developed for extrusion applications. In comparison with standard polypropylene copolymers with the same fluidity, ″Jampilen EP440G″ exhibits higher stiffness, superior impact properties at room and sub-zero temperatures, very high dimensional stability and excellent creep and deforming resistance. The main applications of ″Jampilen EP440G″ are thermoforming, corrugated board and extrusion low molding.
Density: 0.9Jampilen EP440G MFI: 1.3
Characteristic Properties
• Very high impact resistance; High stiffness; Very high dimensional stability; Excellent creep and deforming resistance
Main Applications
• Corrugated board, panels, profiles and crates• Corrugated pipes for automotive and machine construction• Conduit pipes and fittings for electrical distribution and cable protection• Blow molded bottles and containers• Pipe fittings
Additives
• Antioxidant package,
Nucleating agent
EP440G
MethodUnitValueTypical Properties Physical
ASTM D1238g/10min1.3Melt Flow Rate (230 oC, 2.16kg)ASTM D1505g/cm30.9Density
Mechanical
ASTM D790MPa1300Flexural ModulusASTM D638MPa25Tensile Strength at YieldASTM D638%6Tensile Elongation at Yield
ASTM D256J/m500Izod Impact Strength(notched)at 23oC
ASTM D256J/m70Izod Impact Strength(notched)at -20oC
Thermal
ASTM D1525oC150Vicat softening point (10N)ASTM D648oC92H.D.T. (0.46 MPa)
ASTM D3012hours360Accelerated oven ageing in air at 150oC
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201884
″Jampilen EP440L″ is a medium flow heterophasic polypropylene copolymer with improved balance of mechanical properties. The product features high stiffness and outstanding impact strength at low temperatures and is specifically designed for injection molding applications. In comparison with conventional copolymers with the same MFR and same rigidity, ″Jampilen EP440L″, exhibits 35 % higher toughness.″Jampilen EP440L″ is suitable for a wide range of applications in the packaging, automotive and consumer goods industries. Typical applications include luggage, paint pails, buckets, containers, crates, batteries and large toys.
Density: 0.9Jampilen EP440L MFI: 6
Characteristic Properties
• High impact strength; High
stiffness
Main Applications
• Packaging, automotive and consumer goods industries• Luggage, paint pails, buckets• Containers, crates, batteries and large toys
Additives
• Antioxidant package,
Nucleating agent
EP440L
MethodUnitValueTypical Properties Physical
ASTM D1238g/10min6.0Melt Flow Rate (230 oC, 2.16kg)ASTM D1505g/cm30.9Density
Mechanical
ASTM D790MPa1300Flexural ModulusASTM D638MPa25Tensile Strength at YieldASTM D638%6Tensile Elongation at Yield
ASTM D256J/m200Izod Impact Strength(notched)at 23oC
ASTM D256J/m60Izod Impact Strength(notched)at -20oC
Thermal
ASTM D1525oC150Vicat softening point (10N)ASTM D648oC90H.D.T. (0.46 MPa)
ASTM D3012hours360Accelerated oven ageing in air at 150oC
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 85
″Jampilen EP3130UV″ is a non-filled polypropylene copolymer for injection molding with very high impact strength. The product has good U.V. resistance designed for outdoor applications. This grade is used for production of automotive parts, such as bumpers, and compounding.
Density: 0.9Jampilen EP3130UV MFI: 10
Characteristic Properties
• Very high impact strength especially at low temperatures; Good U.V. resistance; Good processability
Main Applications
• Automotive parts• Outdoor applications• Technical articles
Processing Method:Injection molding Compounding
Additives
• Antioxidant package,
Nucleating agent, UV stabilizer
EP3130UV
MethodUnitValueTypical Properties Physical
ASTM D1238g/10min10Melt Flow Rate (230 oC, 2.16kg)ASTM D1505g/cm30.9Density
Mechanical
ASTM D790MPa850Flexural ModulusASTM D638MPa18Tensile Strength at YieldASTM D638%6Tensile Elongation at Yield
ASTM D256J/m500Izod Impact Strength(notched)at 23oC
ASTM D256J/m100Izod Impact Strength(notched)at -20oC
Thermal
ASTM D1525oC135Vicat softening point (10N)ASTM D648oC75H.D.T. (0.46 MPa)
ASTM D3012hours360Accelerated oven ageing in air at 150oC
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201886
″Jampilen EP548R″ is a nucleated, antistatic formulated, high fluidity heterophasic copolymer used for thin-walled injection molding. Items made with ″Jampilen EP548R″ exhibit high stiffness, relatively good impact resistance and excellent antistatic properties. Due to its excellent moldability and short cycle times, ″Jampilen EP548R″ allows high productivity rates. The finished items show good mechanical properties, and high dimensional stability.″Jampilen EP548R″ is very well suited for the production of thin-wall articles or articles with long flow paths such as flower pots, containers, housewares, filters, filter housings and appliance components.″Jampilen EP548R″ is suitable for food contact.
Density: 0.9Jampilen EP548R MFI: 21
Characteristic Properties
• Good impact strength; High
stiffness; Excellent antistatic
properties; Excellent moldability
and short cycle times
Main Applications
• Thin-wall articles• Articles with long flow paths such as flower pots, containers, housewares, filters, filter housings and appliance components• Sports, Leisure and toys
Additives
• Antistatic agent,
Antioxidant package,
Nucleating agent
EP548R
MethodUnitValueTypical Properties Physical
ASTM D1238g/10min21Melt Flow Rate (230 oC, 2.16kg)ASTM D1505g/cm30.9Density
Mechanical
ASTM D790MPa1500Flexural ModulusASTM D638MPa26Tensile Strength at YieldASTM D638%6Tensile Elongation at Yield
ASTM D256J/m90Izod Impact Strength(notched)at 23oC
ASTM D256J/m40Izod Impact Strength(notched)at -20oC
Thermal
ASTM D1525oC150Vicat softening point (10N)ASTM D648oC110H.D.T. (0.46 MPa)
ASTM D3012hours360Accelerated oven ageing in air at 150oC
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 87
″Jampilen EP548T″ is a high melt flow rate, nucleated heterophasic copolymer with a special antistatic additivation used for thin-wall injection molding, IML and houseware applications. The product features improved balance of mechanical properties. The use of ″Jampilen EPX-548T″ allows high productivity due to the easy mold filling and short cycle times.In comparison with conventional copolymers with the same MFR and the same toughness, ″Jampilen EP548T″ exhibits 15% higher rigidity.″Jampilen EP548T″ is suitable for food contact.
Density: 0.9Jampilen EP548T MFI: 50
Characteristic Properties
• High fluidity; Easy mold filling and short cycle times; Desirable impact/ stiffness balance; Good dimensional stability; Unspecified antistatic properties
Main Applications
• TWIM/IML food containers (Marga-rine tubs, yoghurt pots, pots for soft cheese, pudding, etc.)• Housewares• Caps and closures• Flower pots and cool boxes• Sports, leisure and toys
Additives
• Antistatic agent, Antioxidant package, Nucleating agent
EP548T
MethodUnitValueTypical Properties Physical
ASTM D1238g/10min50Melt Flow Rate (230 oC, 2.16kg)ASTM D1505g/cm30.9Density
Mechanical
ASTM D790MPa1450Flexural ModulusASTM D638MPa26Tensile Strength at YieldASTM D638%5Tensile Elongation at Yield
ASTM D256J/m65Izod Impact Strength(notched)at 23oC
ASTM D256J/m45Izod Impact Strength(notched)at -20oC
Thermal
ASTM D1525oC155Vicat softening point (10N)ASTM D648oC105H.D.T. (0.46 MPa)
ASTM D3012hours360Accelerated oven ageing in air at 150oC
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201888
″Jampilen RP345S″ is a polypropylene random copolymer with high fluidity and outstanding transparency and optical properties.″Jampilen RP345S″ is the material of choice for applications where transparency and aesthetics are primary requirements. This grade is designed for injection molding and injection stretch blow molding (ISBM) applications. Thanks to its high fluidity, one can experience reduced cycle times and energy savings compared to conventional grades.″Jampilen RP345S″ is suitable for the packaging of non-oxygen sensitive products; hence, it counts as an effective alternative for PVC and PET in ISBM.
Density: 0.9Jampilen RP345S MFI: 40
Characteristic Properties
• High fluidity; Excellent Optical
properties; Unspecified antistatic
properties; Suitable organoleptic
properties; Excellent processability
and reduced cycle times
Main Applications
• Household containers, housewares• Packaging for food, cosmetics and pharmaceutical products• TWIM• Lids, caps and closures• Medical sector such as syringes, test tubes and vials• Sports, leisure and toys• CD and DVD boxes• Bottles and containers produced with ISBM
Additives
• Antistatic agent,
Antioxidant package, Clarifier
RP345S
MethodUnitValueTypical Properties Physical
ASTM D1238g/10min40Melt Flow Rate (230 oC, 2.16kg)ASTM D1505g/cm30.9Density
Mechanical
ASTM D790MPa1100Flexural ModulusASTM D638MPa28Tensile Strength at YieldASTM D638%9Tensile Elongation at Yield
ASTM D256J/m55Izod Impact Strength(notched)at 23oC
Thermal
ASTM D1525oC128Vicat softening point (10N)ASTM D648oC82H.D.T. (0.46 MPa)
ASTM D3012hours360Accelerated oven ageing in air at 150oC
Optical
ASTM D1003%11Haze (1 mm)ASTM D2457----90Gloss
6
ABS-RubberProducts
Rubber PlantThe Rubber production plant of PadJam Petrochemical Complex is the first and only manufacturer of three products SBS, SB and LCBR in 7 popular grades based on market demand. The capacity of the Plant is 60,000 metric ton per year. The license of the plant is based on the state-of-the-art technical know-how of one of the European best reputed companies, Versalis-Eni S.p.A (Polimeri-Europa). The basic design engineering has been performed by Tecnimont, Italy. The factory is designed and manufactured in accordance with the Batch process to produce a wide range of grades, and is expected to be on operation by the beginning of the 2019. About half of the produced rubber in the Rubber Plant is used as a feed in ABS Plant in order to adjust physical and mechanical properties of ABS, and the remaining rubber could be supplied to market. The feeds of this complex, including Styrene, account for 12,000 tons per year through the pipeline from Pars Petrochemical Complex, 1, 3 butadiene, account for 54,000 thousand tons per year through pipeline from JAM Petrochemical.
ABS PlantThe ABS production plant of PadJam Petrochemical Complex is the first and only manufacturer ABS products with Continuous Mass technology in 9 popular grades based on market demand. Licensing the license of the plant is based on the state-of-the-art technical know-how of one of the European best reputed companies, Versalis-Eni S.p.A (Polimeri-Europa). The basic design engineering has been performed by Tecnimont, Italy. The plant is expected to be on operation in the middle of the 2018. The feeds of this complex, including Styrene, accounts for 140,000 tons per year which is supplied through the pipeline from Pars Petrochemical Complex and Acrylonitrile accounts for 47,000 thousand tons per year which is imported.
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201892
GeneralDensityWater AbsorptionRheologicalMelt Flow Rate (MFR)MechanicalTensile StrengthStrain at breakFlexural StrengthFlexural ModulusIzod Impact Strength Notched
Charpy Impact Strength, NotchedUnnotchedUnnotchedRockwell HardnessThermalVicat Softening Tempreture
Deflection temp. under load (annealed)Ceofficient of linear thermal expansionThermal Conductivity Moulding ShrinkageFlammabilityFlame behaviourGlow wire testElectricalSurface resistivityVolume resistivityDielectric strengthDielectric constant (relative permittivity)Dissipation factor
Properties Test Condition Test Methods Units
Density: 1.04F332
Main Features
• General purpose,
self-coloring
Main Applications
• Households • Small Appliances and white goods Vacuum Cleaners • Electrical components for civil and industrial applications
Keys: Packaged product should be protected from the atmosferic agents and stored out of direct sunlight NB: No Break /M: Matt - Digit following letter/M indicates increasing values of mattness
F332
Injection Moulding Grades
ISO 1183ASTM D 570
ISO 1133
ASTM D 638ASTM D 638ASTM D 790ASTM D 790ISO 180/4AISO 180/4AISO 180/4AISO 180/4AISO 180/1AISO 180/1ADIN 53453DIN 53453DIN 53453ISO 2039/2
ISO 306/A120ISO 306/B120ASTM D 648ASTM D 696ASTM C 177ISO 294.4
UL 94IEC 60695-2-1
IEC 60093IEC 60093IEC 60243IEC 60250IEC 60250
50 mm/min50 mm/min2 mm/min2 mm/min+23°C - thickness 3.2 mm0°C - thickness 3.2 mm- 20°C - thickness 3.2 mm- 40°C - thickness 3.2 mm+23°C - thickness 4 mm- 40°C - thickness 4 mm+23°C+23°C- 40°Cscale R
10 N - 120°C/h50 N - 120°C/h1.8 MPa - 120°C/h
thickness 1.5 mmthickness 3 mm
drydrydry1000 Hz - dry1000 Hz - dry
g/cm3%
g/10min
MPa%MPaMPaJ/mJ/mJ/mJ/mkJ/m²kJ/m²kJ/m²kJ/m²kJ/m²kJ/m²
ºCºCºC10 -5/ºCW/(Km)%
classºC
ohmohm*cmkV/mm
1.040.3
14
42606022501901251009014813NBNBR110
10710210190.170.4-0.6
HB650
10+1410+15303.115*10-³
Product data sheet
GeneralDensityWater AbsorptionRheologicalMelt Flow Rate (MFR)MechanicalTensile StrengthStrain at breakFlexural StrengthFlexural ModulusIzod Impact Strength Notched
Charpy Impact Strength, NotchedUnnotchedUnnotchedRockwell HardnessThermalVicat Softening Tempreture
Deflection temp. under load (annealed)Ceofficient of linear thermal expansionThermal Conductivity Moulding ShrinkageFlammabilityFlame behaviourGlow wire testElectricalSurface resistivityVolume resistivityDielectric strengthDielectric constant (relative permittivity)Dissipation factor
JAM Petrochemical CompanyTechnical Catalogue2018 93
Properties Test Condition Test Methods Units
Density: 1.04E332
Main Features
• Medium heat
resistance,goo flow,
good impact strength
Main Applications
• Automative Interior (Trim parts) • tiles • forms
Keys: Packaged product should be protected from the atmosferic agents and stored out of direct sunlight NB: No Break /M: Matt - Digit following letter/M indicates increasing values of mattness
E332
Injection Moulding Grades
ISO 1183ASTM D 570
ISO 1133
ASTM D 638ASTM D 638ASTM D 790ASTM D 790ISO 180/4AISO 180/4AISO 180/4AISO 180/4AISO 180/1AISO 180/1ADIN 53453DIN 53453DIN 53453ISO 2039/2
ISO 306/A120ISO 306/B120ASTM D 648ASTM D 696ASTM C 177ISO 294.4
UL 94IEC 60695-2-1
IEC 60093IEC 60093IEC 60243IEC 60250IEC 60250
50 mm/min50 mm/min2 mm/min2 mm/min+23°C - thickness 3.2 mm0°C - thickness 3.2 mm- 20°C - thickness 3.2 mm- 40°C - thickness 3.2 mm+23°C - thickness 4 mm- 40°C - thickness 4 mm+23°C+23°C- 40°Cscale R
10 N - 120°C/h50 N - 120°C/h1.8 MPa - 120°C/h
thickness 1.5 mmthickness 3 mm
drydrydry1000 Hz - dry1000 Hz - dry
g/cm3%
g/10min
MPa%MPaMPaJ/mJ/mJ/mJ/mkJ/m²kJ/m²kJ/m²kJ/m²kJ/m²kJ/m²
ºCºCºC10 -5/ºCW/(Km)%
classºC
ohmohm*cmkV/mm
1.040.3
10
4075622200190115908515812NBNBR111
10910410390.170.4-0.6
HB650
10+1410+15303.115*10-³
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201894
GeneralDensityWater AbsorptionRheologicalMelt Flow Rate (MFR)MechanicalTensile StrengthStrain at breakFlexural StrengthFlexural ModulusIzod Impact Strength Notched
Charpy Impact Strength, NotchedUnnotchedUnnotchedRockwell HardnessThermalVicat Softening Tempreture
Deflection temp. under load (annealed)Ceofficient of linear thermal expansionThermal Conductivity Moulding ShrinkageFlammabilityFlame behaviourGlow wire testElectricalSurface resistivityVolume resistivityDielectric strengthDielectric constant (relative permittivity)Dissipation factor
Properties Test Condition Test Methods Units
Density: 1.04L322
Main Features
• Medium heat injection
moulding, high flow,
good thermal
stability during processing
Main Applications
• Domestic appliances thermal resistant items (front panels, frames etc.) Electrical sector
Keys: Packaged product should be protected from the atmosferic agents and stored out of direct sunlight NB: No Break /M: Matt - Digit following letter/M indicates increasing values of mattness
L322
Injection Moulding Grades
ISO 1183ASTM D 570
ISO 1133
ASTM D 638ASTM D 638ASTM D 790ASTM D 790ISO 180/4AISO 180/4AISO 180/4AISO 180/4AISO 180/1AISO 180/1ADIN 53453DIN 53453DIN 53453ISO 2039/2
ISO 306/A120ISO 306/B120ASTM D 648ASTM D 696ASTM C 177ISO 294.4
UL 94IEC 60695-2-1
IEC 60093IEC 60093IEC 60243IEC 60250IEC 60250
50 mm/min50 mm/min2 mm/min2 mm/min+23°C - thickness 3.2 mm0°C - thickness 3.2 mm- 20°C - thickness 3.2 mm- 40°C - thickness 3.2 mm+23°C - thickness 4 mm- 40°C - thickness 4 mm+23°C+23°C- 40°Cscale R
10 N - 120°C/h50 N - 120°C/h1.8 MPa - 120°C/h
thickness 1.5 mmthickness 3 mm
drydrydry1000 Hz - dry1000 Hz - dry
g/cm3%
g/10min
MPa%MPaMPaJ/mJ/mJ/mJ/mkJ/m²kJ/m²kJ/m²kJ/m²kJ/m²kJ/m²
ºCºCºC10 -5/ºCW/(Km)%
classºC
ohmohm*cmkV/mm
1.040.3
23
4520692350170100705013610NBNBR109
99969690.170.4-0.6
HB650
10+1410+15303.115*10-³
Product data sheet
GeneralDensityWater AbsorptionRheologicalMelt Flow Rate (MFR)MechanicalTensile StrengthStrain at breakFlexural StrengthFlexural ModulusIzod Impact Strength Notched
Charpy Impact Strength, NotchedUnnotchedUnnotchedRockwell HardnessThermalVicat Softening Tempreture
Deflection temp. under load (annealed)Ceofficient of linear thermal expansionThermal Conductivity Moulding ShrinkageFlammabilityFlame behaviourGlow wire testElectricalSurface resistivityVolume resistivityDielectric strengthDielectric constant (relative permittivity)Dissipation factor
JAM Petrochemical CompanyTechnical Catalogue2018 95
Properties Test Condition Test Methods Units
Density: 1.04F232
Main Features
• General purpose,
high flow injection moulding
grade, good impact
resistance, excellent gloss
Main Applications
• Small and large • household appliances• vacuum cleaners• toys• telephones and consumer electronics
Keys: Packaged product should be protected from the atmosferic agents and stored out of direct sunlight NB: No Break /M: Matt - Digit following letter/M indicates increasing values of mattness
F232
Injection Moulding Grades
ISO 1183ASTM D 570
ISO 1133
ASTM D 638ASTM D 638ASTM D 790ASTM D 790ISO 180/4AISO 180/4AISO 180/4AISO 180/4AISO 180/1AISO 180/1ADIN 53453DIN 53453DIN 53453ISO 2039/2
ISO 306/A120ISO 306/B120ASTM D 648ASTM D 696ASTM C 177ISO 294.4
UL 94IEC 60695-2-1
IEC 60093IEC 60093IEC 60243IEC 60250IEC 60250
50 mm/min50 mm/min2 mm/min2 mm/min+23°C - thickness 3.2 mm0°C - thickness 3.2 mm- 20°C - thickness 3.2 mm- 40°C - thickness 3.2 mm+23°C - thickness 4 mm- 40°C - thickness 4 mm+23°C+23°C- 40°Cscale R
10 N - 120°C/h50 N - 120°C/h1.8 MPa - 120°C/h
thickness 1.5 mmthickness 3 mm
drydrydry1000 Hz - dry1000 Hz - dry
g/cm3%
g/10min
MPa%MPaMPaJ/mJ/mJ/mJ/mkJ/m²kJ/m²kJ/m²kJ/m²kJ/m²kJ/m²
ºCºCºC10 -5/ºCW/(Km)%
classºC
ohmohm*cmkV/mm
1.040.3
14
4520692350170100705013610NBNBR109
10710110290.170.4-0.6
HB650
10+1410+15303.115*10-³
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201896
GeneralDensityWater AbsorptionRheologicalMelt Flow Rate (MFR)MechanicalTensile StrengthStrain at breakFlexural StrengthFlexural ModulusIzod Impact Strength Notched
Charpy Impact Strength, NotchedUnnotchedUnnotchedRockwell HardnessThermalVicat Softening Tempreture
Deflection temp. under load (annealed)Ceofficient of linear thermal expansionThermal Conductivity Moulding ShrinkageFlammabilityFlame behaviourGlow wire testElectricalSurface resistivityVolume resistivityDielectric strengthDielectric constant (relative permittivity)Dissipation factor
Properties Test Condition Test Methods Units
Density: 1.04B432/E
Main Features
• Sheets and
profile Medium
impact strength
Main Applications
• Plain or coextruded with high draw ratios for refrigeration, sanitary, automotive, packaging, housholding (profiles)
Keys: Packaged product should be protected from the atmosferic agents and stored out of direct sunlight NB: No Break /M: Matt - Digit following letter/M indicates increasing values of mattness
B432/E
Extrusion Moulding Grades
ISO 1183ASTM D 570
ISO 1133
ASTM D 638ASTM D 638ASTM D 790ASTM D 790ISO 180/4AISO 180/4AISO 180/4AISO 180/4AISO 180/1AISO 180/1ADIN 53453DIN 53453DIN 53453ISO 2039/2
ISO 306/A120ISO 306/B120ASTM D 648ASTM D 696ASTM C 177ISO 294.4
UL 94IEC 60695-2-1
IEC 60093IEC 60093IEC 60243IEC 60250IEC 60250
50 mm/min50 mm/min2 mm/min2 mm/min+23°C - thickness 3.2 mm0°C - thickness 3.2 mm- 20°C - thickness 3.2 mm- 40°C - thickness 3.2 mm+23°C - thickness 4 mm- 40°C - thickness 4 mm+23°C+23°C- 40°Cscale R
10 N - 120°C/h50 N - 120°C/h1.8 MPa - 120°C/h
thickness 1.5 mmthickness 3 mm
drydrydry1000 Hz - dry1000 Hz - dry
g/cm3%
g/10min
MPa%MPaMPaJ/mJ/mJ/mJ/mkJ/m²kJ/m²kJ/m²kJ/m²kJ/m²kJ/m²
ºCºCºC10 -5/ºCW/(Km)%
classºC
ohmohm*cmkV/mm
1.040.3
4
454568230022016512510017912NBNBR110
10910410490.170.4-0.6
HB650
10+1410+15303.115*10-³
Product data sheet
GeneralDensityWater AbsorptionRheologicalMelt Flow Rate (MFR)MechanicalTensile StrengthStrain at breakFlexural StrengthFlexural ModulusIzod Impact Strength Notched
Charpy Impact Strength, NotchedUnnotchedUnnotchedRockwell HardnessThermalVicat Softening Tempreture
Deflection temp. under load (annealed)Ceofficient of linear thermal expansionThermal Conductivity Moulding ShrinkageFlammabilityFlame behaviourGlow wire testElectricalSurface resistivityVolume resistivityDielectric strengthDielectric constant (relative permittivity)Dissipation factor
JAM Petrochemical CompanyTechnical Catalogue2018 97
Properties Test Condition Test Methods Units
Density: 1.04B532/E
Main Features
• Sheets and profile.
Good impact strength,
high toughness
Main Applications
• Plain or coextruded with high draw ratios for refrigeration, sanitary, automotive, packaging, housholding (profiles)
Keys: Packaged product should be protected from the atmosferic agents and stored out of direct sunlight NB: No Break /M: Matt - Digit following letter/M indicates increasing values of mattness
B532/E
Extrusion Moulding Grades
ISO 1183ASTM D 570
ISO 1133
ASTM D 638ASTM D 638ASTM D 790ASTM D 790ISO 180/4AISO 180/4AISO 180/4AISO 180/4AISO 180/1AISO 180/1ADIN 53453DIN 53453DIN 53453ISO 2039/2
ISO 306/A120ISO 306/B120ASTM D 648ASTM D 696ASTM C 177ISO 294.4
UL 94IEC 60695-2-1
IEC 60093IEC 60093IEC 60243IEC 60250IEC 60250
50 mm/min50 mm/min2 mm/min2 mm/min+23°C - thickness 3.2 mm0°C - thickness 3.2 mm- 20°C - thickness 3.2 mm- 40°C - thickness 3.2 mm+23°C - thickness 4 mm- 40°C - thickness 4 mm+23°C+23°C- 40°Cscale R
10 N - 120°C/h50 N - 120°C/h1.8 MPa - 120°C/h
thickness 1.5 mmthickness 3 mm
drydrydry1000 Hz - dry1000 Hz - dry
g/cm3%
g/10min
MPa%MPaMPaJ/mJ/mJ/mJ/mkJ/m²kJ/m²kJ/m²kJ/m²kJ/m²kJ/m²
ºCºCºC10 -5/ºCW/(Km)%
classºC
ohmohm*cmkV/mm
1.040.3
5
3545682300280190150125201016NBNBR110
10810410490.170.4-0.6
HB650
10+1410+15303.115*10-³
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 201898
GeneralDensityWater AbsorptionRheologicalMelt Flow Rate (MFR)MechanicalTensile StrengthStrain at breakFlexural StrengthFlexural ModulusIzod Impact Strength Notched
Charpy Impact Strength, NotchedUnnotchedUnnotchedRockwell HardnessThermalVicat Softening Tempreture
Deflection temp. under load (annealed)Ceofficient of linear thermal expansionThermal Conductivity Moulding ShrinkageFlammabilityFlame behaviourGlow wire testElectricalSurface resistivityVolume resistivityDielectric strengthDielectric constant (relative permittivity)Dissipation factor
Properties Test Condition Test Methods Units
Density: 1.04B732/E
Main Features
• Very high
impact strength
Main Applications
• Extrusion of thick sheets for sanitary and automotive applications
Keys: Packaged product should be protected from the atmosferic agents and stored out of direct sunlight NB: No Break /M: Matt - Digit following letter/M indicates increasing values of mattness
B732/E
Extrusion Moulding Grades
ISO 1183ASTM D 570
ISO 1133
ASTM D 638ASTM D 638ASTM D 790ASTM D 790ISO 180/4AISO 180/4AISO 180/4AISO 180/4AISO 180/1AISO 180/1ADIN 53453DIN 53453DIN 53453ISO 2039/2
ISO 306/A120ISO 306/B120ASTM D 648ASTM D 696ASTM C 177ISO 294.4
UL 94IEC 60695-2-1
IEC 60093IEC 60093IEC 60243IEC 60250IEC 60250
50 mm/min50 mm/min2 mm/min2 mm/min+23°C - thickness 3.2 mm0°C - thickness 3.2 mm- 20°C - thickness 3.2 mm- 40°C - thickness 3.2 mm+23°C - thickness 4 mm- 40°C - thickness 4 mm+23°C+23°C- 40°Cscale R
10 N - 120°C/h50 N - 120°C/h1.8 MPa - 120°C/h
thickness 1.5 mmthickness 3 mm
drydrydry1000 Hz - dry1000 Hz - dry
g/cm3%
g/10min
MPa%MPaMPaJ/mJ/mJ/mJ/mkJ/m²kJ/m²kJ/m²kJ/m²kJ/m²kJ/m²
ºCºCºC10 -5/ºCW/(Km)%
classºC
ohmohm*cmkV/mm
1.040.3
4.5
4545602200350300200140281220NBNBR103
10910410090.170.4-0.6
HB650
10+1410+15303.115*10-³
Product data sheet
GeneralDensityWater AbsorptionRheologicalMelt Flow Rate (MFR)MechanicalTensile StrengthStrain at breakFlexural StrengthFlexural ModulusIzod Impact Strength Notched
Charpy Impact Strength, NotchedUnnotchedUnnotchedRockwell HardnessThermalVicat Softening Tempreture
Deflection temp. under load (annealed)Ceofficient of linear thermal expansionThermal Conductivity Moulding ShrinkageFlammabilityFlame behaviourGlow wire testElectricalSurface resistivityVolume resistivityDielectric strengthDielectric constant (relative permittivity)Dissipation factor
JAM Petrochemical CompanyTechnical Catalogue2018 99
Properties Test Condition Test Methods Units
Density: 1.04D232/M3
Main Features
• Low gloss, extrusion
Main Applications
• Extrusion/ coextrusion of sheets with matt surface, household profiles
Keys: Packaged product should be protected from the atmosferic agents and stored out of direct sunlight NB: No Break /M: Matt - Digit following letter/M indicates increasing values of mattness
D232/M3
Extrusion Moulding Grades
ISO 1183ASTM D 570
ISO 1133
ASTM D 638ASTM D 638ASTM D 790ASTM D 790ISO 180/4AISO 180/4AISO 180/4AISO 180/4AISO 180/1AISO 180/1ADIN 53453DIN 53453DIN 53453ISO 2039/2
ISO 306/A120ISO 306/B120ASTM D 648ASTM D 696ASTM C 177ISO 294.4
UL 94IEC 60695-2-1
IEC 60093IEC 60093IEC 60243IEC 60250IEC 60250
50 mm/min50 mm/min2 mm/min2 mm/min+23°C - thickness 3.2 mm0°C - thickness 3.2 mm- 20°C - thickness 3.2 mm- 40°C - thickness 3.2 mm+23°C - thickness 4 mm- 40°C - thickness 4 mm+23°C+23°C- 40°Cscale R
10 N - 120°C/h50 N - 120°C/h1.8 MPa - 120°C/h
thickness 1.5 mmthickness 3 mm
drydrydry1000 Hz - dry1000 Hz - dry
g/cm3%
g/10min
MPa%MPaMPaJ/mJ/mJ/mJ/mkJ/m²kJ/m²kJ/m²kJ/m²kJ/m²kJ/m²
ºCºCºC10 -5/ºCW/(Km)%
classºC
ohmohm*cmkV/mm
1.040.3
8
271004015501109080759.579NBNBR97
10610110190.170.4-0.6
HB650
10+1410+15303.115*10-³
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 2018100
GeneralDensityWater AbsorptionRheologicalMelt Flow Rate (MFR)MechanicalTensile StrengthStrain at breakFlexural StrengthFlexural ModulusIzod Impact Strength Notched
Charpy Impact Strength, NotchedUnnotchedUnnotchedRockwell HardnessThermalVicat Softening Tempreture
Deflection temp. under load (annealed)Ceofficient of linear thermal expansionThermal Conductivity Moulding ShrinkageFlammabilityFlame behaviourGlow wire testElectricalSurface resistivityVolume resistivityDielectric strengthDielectric constant (relative permittivity)Dissipation factor
Properties Test Condition Test Methods Units
Density: 1.04C442
Main Features
• Heat resistance,
good flow and good
impact strength
Main Applications
• Automotive interior (extruded profiles, interior trim), exterior (grilles, mirrors)
Keys: Packaged product should be protected from the atmosferic agents and stored out of direct sunlight NB: No Break /M: Matt - Digit following letter/M indicates increasing values of mattness
C442
Extrusion Moulding Grades
ISO 1183ASTM D 570
ISO 1133
ASTM D 638ASTM D 638ASTM D 790ASTM D 790ISO 180/4AISO 180/4AISO 180/4AISO 180/4AISO 180/1AISO 180/1ADIN 53453DIN 53453DIN 53453ISO 2039/2
ISO 306/A120ISO 306/B120ASTM D 648ASTM D 696ASTM C 177ISO 294.4
UL 94IEC 60695-2-1
IEC 60093IEC 60093IEC 60243IEC 60250IEC 60250
50 mm/min50 mm/min2 mm/min2 mm/min+23°C - thickness 3.2 mm0°C - thickness 3.2 mm- 20°C - thickness 3.2 mm- 40°C - thickness 3.2 mm+23°C - thickness 4 mm- 40°C - thickness 4 mm+23°C+23°C- 40°Cscale R
10 N - 120°C/h50 N - 120°C/h1.8 MPa - 120°C/h
thickness 1.5 mmthickness 3 mm
drydrydry1000 Hz - dry1000 Hz - dry
g/cm3%
g/10min
MPa%MPaMPaJ/mJ/mJ/mJ/mkJ/m²kJ/m²kJ/m²kJ/m²kJ/m²kJ/m²
ºCºCºC10 -5/ºCW/(Km)%
classºC
ohmohm*cmkV/mm
1.040.3
6
434565230020016512510017912NBNBR110
11410810890.170.4-0.6
HB650
10+1410+15303.115*10-³
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 101
Properties Test Methods Analytical Manual Units GeneralMooney ViscosityBound StyreneBlock styreneSolution viscosity*Gel contentMolecular weightCoupling efficiencyVolatile matter contentResidual solventColourSolution color (Pt/Co)Vinyl contentAsh contentSolvent extractablesPhysical Form
Packaging
MPP16MPP5-MPP6MPP8MPP9MPP12MPP1MPP1MPP10MPP18MPP13
MPP5-MPP6MPP15MPP11
ASTM D1646ASTM D5775ASTM D3314ASTM D5774
ASTM D5668
ASTM E313ASTM D1209
ASTM D5667ASTM D5774
ML1+4 @ 100°Cwt %wt %cPsarbitraryKDalton%wt %ppmYellow indexarbitrarywt % on butadienewt %wt %
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 2018102
Properties Test Methods Analytical Manual Units GeneralMooney ViscosityBound StyreneBlock styreneSolution viscosity*Gel contentMolecular weightCoupling efficiencyVolatile matter contentResidual solventColourSolution color (Pt/Co)Vinyl contentAsh contentSolvent extractablesPhysical Form
Packaging
MPP16MPP5-MPP6MPP8MPP9MPP12MPP1MPP1MPP10MPP18MPP13
MPP5-MPP6MPP15MPP11
ASTM D1646ASTM D5775ASTM D3314ASTM D5774
ASTM D5668
ASTM E313ASTM D1209
ASTM D5667ASTM D5774
ML1+4 @ 100°Cwt %wt %cPsarbitraryKDalton%wt %ppmYellow indexarbitrarywt % on butadienewt %wt %
SBS - SOL T6302
Main Applications
• Bitumen modification, particularly in road paving applications, in compounding fpr both footwear and technical goods, and in adhesive applications
Key Features
• Linear block copolymer, providing excellent mechanical properties, high strength and elasticity, combined with good dispersability and processability.
SOL T6302
Europrene
Pellet form
Bags on Pallet, Big bags and wooden crates
N/A29 – 33100N/AN/A95 - 12584 min1 max< 1010 maxN/A10.0 – 14.0N/AN/A
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 103
Properties Test Methods Analytical Manual Units GeneralMooney ViscosityBound StyreneBlock styreneSolution viscosity*Gel contentMolecular weightCoupling efficiencyVolatile matter contentResidual solventColourSolution color (Pt/Co)Vinyl contentAsh contentSolvent extractablesPhysical Form
Packaging
MPP16MPP5-MPP6MPP8MPP9MPP12MPP1MPP1MPP10MPP18MPP13
MPP5-MPP6MPP15MPP11
ASTM D1646ASTM D5775ASTM D3314ASTM D5774
ASTM D5668
ASTM E313ASTM D1209
ASTM D5667ASTM D5774
ML1+4 @ 100°Cwt %wt %cPsarbitraryKDalton%wt %ppmYellow indexarbitrarywt % on butadienewt %wt %
SBS - SOL T161B
Main Applications
• Bitumen modification for waterproofing membranes used in roofing and bridge insulation, road paving & pipe coating
Key Features
• block copolymer with radial moleculare structureexcellent mechanical properties, high strength and elasticity in a wide range of formulated products
SOL T161B
Europrene
Pellet form, Powder form
Bags on Pallet, Big bags and wooden crates
N/A29 - 33100N/AN/A220 - 26084 min1.0 max< 1010 maxN/A10.0 – 14.0N/AN/A
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 2018104
Properties Test Methods Analytical Manual Units GeneralMooney ViscosityBound StyreneBlock styreneSolution viscosity*Gel contentMolecular weightCoupling efficiencyVolatile matter contentResidual solventColourSolution color (Pt/Co)Vinyl contentAsh contentSolvent extractablesPhysical Form
Packaging
MPP16MPP5-MPP6MPP8MPP9MPP12MPP1MPP1MPP10MPP18MPP13
MPP5-MPP6MPP15MPP11
ASTM D1646ASTM D5775ASTM D3314ASTM D5774
ASTM D5668
ASTM E313ASTM D1209
ASTM D5667ASTM D5774
ML1+4 @ 100°Cwt %wt %cPsarbitraryKDalton%wt %ppmYellow indexarbitrarywt % on butadienewt %wt %
SBS - SOL T6306
Main Applications
• Bitumen modification in waterproofing systems, formulated compounds for shoe soles and technical goods
Key Features
• block copolymer designed for bitumen modification in waterproofing membranes applications. The grade imparts exellent mechanical properties and elasticity to the modified bitumen. The radial structure and the high styrene block content assures outstanding performance under service condition, particularly in the high temprature range
SOL T6306
Europrene
Pellet form, Powder form
Bags on Pallet, Big bags and wooden crates
N/A34 - 38100N/AN/A245 - 27585 min1 max< 1015 maxN/A10.0 – 14.0N/AN/A
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 105
Properties Test Methods Analytical Manual Units GeneralMooney ViscosityBound StyreneBlock styreneSolution viscosity*Gel contentMolecular weightCoupling efficiencyVolatile matter contentResidual solventColourSolution color (Pt/Co)Vinyl contentAsh contentSolvent extractablesPhysical Form
Packaging
MPP16MPP5-MPP6MPP8MPP9MPP12MPP1MPP1MPP10MPP18MPP13
MPP5-MPP6MPP15MPP11
ASTM D1646ASTM D5775ASTM D3314ASTM D5774
ASTM D5668
ASTM E313ASTM D1209
ASTM D5667ASTM D5774
ML1+4 @ 100°Cwt %wt %cPsarbitraryKDalton%wt %ppmYellow indexarbitrarywt % on butadienewt %wt %
SB - SOL B183
Main Applications
• SOL 183 is mainly used in plastic material (PS, ABS) modification.
Key Features
• Europrene SOL 183 is a dry solution styrene butadiene tapered block copolymer, polymerized using alkyl lithium catalyst. Its typical styrene content is 11% and vinyl (1,2 butadiene) content is 10%. The block styrene content is typically 5%. The polymer contains a non-staining antioxidant. It is produced in a batch polymerization process
SOL B183
Europrene
Bale (25Kg)
30-36 Bales in wooden crates
60 – 809.0 – 11.04 – 6N/AN/AN/AN/A0.75 maxN/AN/AN/A9.0 – 11.00.2 maxN/A
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 2018106
Properties Test Methods Analytical Manual Units GeneralMooney ViscosityBound StyreneBlock styreneSolution viscosity*Gel contentMolecular weightCoupling efficiencyVolatile matter contentResidual solventColourSolution color (Pt/Co)Vinyl contentAsh contentSolvent extractablesPhysical Form
Packaging
MPP16MPP5-MPP6MPP8MPP9MPP12MPP1MPP1MPP10MPP18MPP13
MPP5-MPP6MPP15MPP11
ASTM D1646ASTM D5775ASTM D3314ASTM D5774
ASTM D5668
ASTM E313ASTM D1209
ASTM D5667ASTM D5774
ML1+4 @ 100°Cwt %wt %cPsarbitraryKDalton%wt %ppmYellow indexarbitrarywt % on butadienewt %wt %
LCBR - Intene P30
Main Applications• Mainly used in bulk and suspension ABS process where low-cis polybutadiene (4-15%wt on the final product) with a low viscosity is required. The ability of the rubber domains to promote craze formation and shear yielding accounts for improved impact properties; crazing and shear yielding function as energy-dissipating processes that can inhibit the formation of a crack that would otherwise produce catastrophic failure. The star like structure of P30 guarantees a low value in viscosity and, contemporary, a molecular weight sufficiently high. The high capacity of loading carbon black and good extrudibility made this grade suitable for abrasion strips construction in tire building.
Key Features
• The star like structure of P30 guarantees value in viscosity and, contemporary, a molecular weight sufficiently high.the high capacity of loading carbon black and good extrudibility made this grade suita abrasion strips construction in tire building.
Intene P30
Bale (25Kg)
30-36 Bales in wooden crates
45 – 55N/AN/A35 - 504 maxN/AN/A0.75 maxN/AN/A10 max11 – 130.2 maxN/A
Intene
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue2018 107
Properties Test Methods Analytical Manual Units GeneralMooney ViscosityBound StyreneBlock styreneSolution viscosity*Gel contentMolecular weightCoupling efficiencyVolatile matter contentResidual solventColourSolution color (Pt/Co)Vinyl contentAsh contentSolvent extractablesPhysical Form
Packaging
MPP16MPP5-MPP6MPP8MPP9MPP12MPP1MPP1MPP10MPP18MPP13
MPP5-MPP6MPP15MPP11
ASTM D1646ASTM D5775ASTM D3314ASTM D5774
ASTM D5668
ASTM E313ASTM D1209
ASTM D5667ASTM D5774
ML1+4 @ 100°Cwt %wt %cPsarbitraryKDalton%wt %ppmYellow indexarbitrarywt % on butadienewt %wt %
LCBR - BR245
Main Applications• BR 245 polybutadiene is used in tire compounds and in some mechanical good compounds. Good hysteresis properties of BR 245 allow it to be blended with natural rubber to produce enhanced properties in truck tire treads. The addition of polybutadiene low cis to natural rubber upgrades abrasion and cracking resistance, maintains good resilience and also provides better resistance to overcure and degradation during aging. BR 245 and SOL R 1204 were tried in blends with natural rubber in large size passengers tyre reducing groove cracking compared to natural rubber.Key Features• BR245 rubber is a solution polymerized low cis star branched, low coupled, dry polybutadiene produced using alkyl lithium initiator in batch reactors.
Key Features
• BR245 rubber is a solution polymerized low cis star branched, low coupled, dry polybutadiene produced using alkyl lithium initiator in batch reactors.
BR245
Bale (25Kg)
30-36 Bales in wooden crates
50 – 60N/AN/AN/AN/AN/AN/A0.6 maxN/AN/AN/A11 – 130.08N/A
Europrene
Product data sheet
JAM Petrochemical CompanyTechnical Catalogue 2018108
Properties Test Methods Analytical Manual Units GeneralMooney ViscosityBound StyreneBlock styreneSolution viscosity*Gel contentMolecular weightCoupling efficiencyVolatile matter contentResidual solventColourSolution color (Pt/Co)Vinyl contentAsh contentSolvent extractablesPhysical Form
Packaging
MPP16MPP5-MPP6MPP8MPP9MPP12MPP1MPP1MPP10MPP18MPP13
MPP5-MPP6MPP15MPP11
ASTM D1646ASTM D5775ASTM D3314ASTM D5774
ASTM D5668
ASTM E313ASTM D1209
ASTM D5667ASTM D5774
ML1+4 @ 100°Cwt %wt %cPsarbitraryKDalton%wt %ppmYellow indexarbitrarywt % on butadienewt %wt %
LCBR - BR 277
Main Applications
• BR 277 oil extended polybutadiene is used in tire compounds and in some mechanical good compounds.
Key Features
• BR277 rubber is a solution polymerized low cis star branched, low efficiency coupled, oil extended polybutadiene produced using alkyl lithium initiator in batch reactors.
BR 277
Bale (25Kg)
30-36 Bales in wooden crates
37 – 47N/AN/AN/AN/AN/AN/A0.3 maxN/AN/AN/A11 – 130.0426.3–29.3
Europrene