technical sheet – photo-frames and porcelain photo for tombstones
TRANSCRIPT
REAL VOTIVA STORE Online funeral articles shop www.realvotivastore.com [email protected]
Pag. 1 di 4
Technical Sheet – Photo‐frames and porcelain photo Features, size and mounting methods
General features
One of the main elements of an headstone is the portrait
photo‐frame that makes it precious the image of the dear
departed. Real Votiva produces headstone picture frames in
bronze (created with die casting or lost wax techniques),
porcelain (with a wide range of colors in marble or hand‐
decorated) and steel.
The photo‐frames can have oval or rectangular shape and are
produced in various formats, including the most widely used
9x12 cm and 11x15 cm. Typically, they are fixed through two
back pins directly to the surface of the tombstones but there
are also different models applicable to the ground, ideal for
cemetery monuments or horizontal graves.
The frames have standard formats perfectly adaptable to the
photos in porcelain which can be produced on demand.
The frames are covered with a special coating that ensures
weatherproof and are very useful especially for graves planted outdoors.
Photo‐frame sizes
The frames sizes indicated in the catalogue refer to the inner edges. The dimensions are always indicated in
cm L x H, where L represents the width and H is the height.
REAL VOTIVA STORE Online funeral articles shop www.realvotivastore.com [email protected]
Pag. 2 di 4
Porcelain photo sizes
Porcelain photo sizes available in our catalogue vary from 4x6 cm up to large sizes like 50x70 cm. They are
available in oval or horizontal shape and can be used in combination with photo‐frames.
Size matching between photo‐frame and porcelain photo
Usually porcelain photos are used in combination with photo‐frames of the same size so it’s important to
be sure that the relative sizes are corresponding. Actually, between the size of the inner edge of the frame
and the size of the porcelain photo exists a slight difference of a few millimeters so that the overlapping
frame can serve as support to the porcelain photo.
Conventionally, the catalogue sizes of frames and porcelain photo are standardized, so that ordering a
photo‐frame and a porcelain photo of the same nominal dimensions assures the perfect correspondence
between the two elements.
REAL VOTIVA STORE Online funeral articles shop www.realvotivastore.com [email protected]
Pag. 3 di 4
How to apply the frame on the porcelain photo.
Before fixing the photo‐frame on the tombstone surface, the porcelain photo is secured to the frame by
means of two flexible steel fins placed in the back of the frame.
How to mount the photo‐frame
Photo‐frames can be mounted by means of two pin in the back. The application requires to carry out two
small holes in correspondence of the pins. The frame is fixed with mastic for marble or other type of
adhesive depending on the application surface. It is advisable to drill the holes using a drill bit with a
diameter slightly greater than the pins diameter in order to allow the application of the mastic into the
holes. At the end blow into the holes to remove residual powder inside.
REAL VOTIVA STORE Online funeral articles shop www.realvotivastore.com [email protected]
Pag. 4 di 4
Preparation of the mastic. To facilitate the application of mastic inside the holes, it is recommend using a
liquid but viscous mastic. Using clean tools, take out from the tin the amount of mastic to use and add the
right amount of catalyst paste (according to the quantities indicated on the package, e.g. from 1 to 3 grams
of hardener per 100 grams of product); mix the two components by means of a spatula. Note that the
curing time will shorten with temperatures above 25° C and will be longer with lower temperatures.
Photo‐frames with base for floor mounting.
As an alternative to the vertical application frame (P), are available various photo‐frame models with
ground attack (T) i.e. on a horizontal surface, suitable to be mounted on monuments or tombs on the
ground. In this case the frame is applied onto a tilted L‐shaped base which is fixed by means of two pins at
the base (see figures).
REAL VOTIVA STORE ‐ Online funeral articles shop Contrada Pozzo, 73040 ‐ Melissano ‐ LECCE (Italy) www.realvotivastore.com [email protected]