toepassing van het benor-merk in de sector van de ... · het bijgevoegd technisch dossier (td)...
TRANSCRIPT
OCBS Vereniging zonder winstoogmerk
Ravensteinstraat 4 B 1000 BRUSSEL
www.ocab-ocbs.com
________________________________________________________________________________________________ © OCBS OCAB 2016
TECHNISCH DOSSIER DTD 592
Herz. 4 2016/3
DTD 592/4 2016
TOEPASSING VAN HET BENOR-MERK IN DE SECTOR VAN DE STAALPRODUCTEN VOOR BETON
CONTROLEMODALITEITEN TOEPASSELIJK OP DE "GEBRUIKERS VAN
HET MERK" - WALSERIJEN, DRAADTREKKERIJEN, PRODUCENTEN VAN GELASTE WAPENINGSNETTEN, VAN TOT VLAKKE PANELEN
SAMENGESTELDE WAPENINGEN OF VAN TRALIELIGGERS
TECHNISCH DOSSIER
HERZIENING 4
BENOR vzw
Goedgekeurd door de Raad van Bestuur op 11/03/2016
OCBS - document nr. 592/4 Pagina 1 van 4
- Voorgesteld door het Technisch Bureau 1 op 23 februari 2016 - Goedgekeurd door de Raad van Bestuur op 11 maart 2016
592-4n
TOEPASSING VAN HET BENOR-MERK IN DE
SECTOR VAN DE STAALPRODUCTEN VOOR BETON
CONTROLEMODALITEITEN TOEPASSELIJK OP DE
"GEBRUIKERS VAN HET MERK" – WALSERIJEN, DRAADTREKKERIJEN PRODUCENTEN VAN GELASTE WAPENINGSNETTEN,
VAN TOT VLAKKE PANELEN SAMENGESTELDE WAPENINGEN OF VAN TRALIELIGGERS
TECHNISCH DOSSIER
OCBS - document nr. 592/4 Pagina 2 van 4
STAVEN/DRADEN
WAPENINGSNETTEN/PANELEN
TRALIELIGGERS
(Bijlage: 1 dossier)
TECHNISCH DOSSIER
Deze nota vormt een leidraad voor de opstelling van een technisch dossier overeenkomstig document TRA 270, 271, 345, 346 en 413, en in het bijzonder paragraaf A.1.1 eruit. Het schema van dit dossier is in bijlage weergegeven. Enkel bladzijden 1 en 2 zijn verplicht: - de “A”-versie (bladzijden 1A en 2A) wordt gebruikt voor het oorspronkelijk technisch dossier; - de “B”-versie wordt gebruikt voor de jaarlijkse aanpassingen. Het controle-organisme moet ingelicht worden over elke wijziging.
Bladzijde van het TD
A. Titelblad met vermelding van: TD 1A - 1B
A.1. TECHNISCH DOSSIER WAPENINGSNET/PANEEL/TRALIELIGGER. A.2. Documenten waarnaar verwezen wordt: NBN A24-301/-302/-303/-304,
PTV 302/303/304/305/307/308 en TRA 270/271/345/346/413. A.3. Aantal bladzijden. A.4. Stand van het dossier: ontwerp, definitief. A.5. Controle-organisme: nazicht, akkoord, datum, stempel, handtekening. A.6. OCBS: nazicht, akkoord, datum, stempel, handtekening (enkel pag. TD 1A).
OCBS - document nr. 592/4 Pagina 3 van 4
A.7. Producent: naam en nummer bij het OCBS, datum, stempel, handtekening. A.8. Opmerkingen van het controle-organisme. A.9. Opmerkingen van de producent. A.10. Opmerkingen van het OCBS (enkel pag. 1A). A.11. Tabel met alle wijzigingen van het technisch dossier: herzieningsindex, aard van de
wijziging, betrokken bladzijde(n), datum van de wijziging (enkel pag. TD 1B).
B. Verklaring van de producent. TD 2A - 2B
C. Inhoudstafel. TD 3
D. Volledige benaming van het verkoopsorganisme (naam, volledig adres, tel., fax, e-mail,...) TD 4
E. E.Aanduiding van de verantwoordelijke(n) van de kwaliteitscontrole en zijn (hun) plaatsvervanger(s) (na
Een organogram van de maatschappij mag eventueel bijgevoegd worden TD 4
F. Voorstelling: TD 6
Beschrijving van zowel de administratieve als technische organisatie van de productie
G. Identificatie : TD 6
1. Markering (staven en draden)
Tekening waarop de geometrie voorkomt van elk ribveld evenals een dwarsdoorsnede van de staaf of draad.
2. Etiketten
Een model van elke type dat minstens de informatie van de § A.1.5 van de overeenkomstige TRA vermeldt.
OCBS - document nr. 592/4 Pagina 4 van 4
H. Leveringsborderel: TD 6
Model dat minstens vermeldt:
- het BENOR-logo met het onderscheidingsnummer van de gebruiker van het merk (x) Staven/draden/Netten Panelen Tralieliggers (x) (x) (x) NBN A 24-301 NBN A 24-301 + PTV 308 NBN A 24-301 + PTV 305
Opm : Voor staven, bij gebruik van een alternatief profiel "NBN A 24-301" is vervangen tegen "NBN A24-301 + PTV 307"
- naam van de producent; - stijgend volgnummer; - volledige kwalitatieve en kwantitatieve aanduiding van de levering; - leveringsdatum; - naam en adres van de klant en leveringsadres; - alle verwijzingen naar de bestelling door de klant.
I. Verwerkt staal
Aanduiding van de verschillende staalkwaliteiten, van de verschillende producenten, van alle aangewende diameters en van hun BENOR-kwaliteit, al dan niet. TD 7
J. Productie
Beschrijving van alle aangewende productiemiddelen. TD 8
K. Bemonsteringsplan
In overeenstemming met TRA 270/271/345/346/413 § B.1.2 moet het bemonsteringsplan de types en frequenties van bemonstering vastleggen, evenals de aard van de controles en hun registratie. Indien voor de berekening van fR gebruik wordt gemaakt van de vereenvoudigde formule fR=.h/c (volgens de modaliteiten beschreven in de van toepassing zijnde normatieve documenten); dient deze -waarde te worden vermeld in het TD en dient er een –door de certificeringsinstelling– goedgekeurd dossier beschikbaar te zijn. Staven / draden TD bijlage 1a Netten / vlakke panelen TD bijlage 1b Tralieliggers TD bijlage 1c
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
1
TD pagina 1A
OORSPRONKELIJK TECHNISCH DOSSIER Ontwerp □ Definitief □
Staven/Draden/Netten/Panelen/Tralieliggers (NBN A24-301/-302/-303/-304, PTV 302/303/304/305/308
en TRA 270/271/345/346/413) (*) Aantal pagina’s y
Controle organisme
OCBS Producent
Nagezien □ Nagezien □ Naam : Nummer : Akkoord □ Akkoord □
Datum Technisch Dossier
Datum :
Naam Paraaf
Stempel
Opmerkingen van het controle-organisme
Opmerkingen van de producent
Opmerkingen van het OCBS
(*) De onnodige vermeldingen doorhalen
OCAB - OCBS
Vereniging zonder winstoogmerkRavensteinstraat 4 B 1000 Brussel
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
2
DT pagina 1B
TECHNISCH DOSSIER : AANPASSING Ontwerp □ Definitief □
Staven/Draden/Netten/Panelen/Tralieliggers (NBN A24-301/-302/-303/-304, PTV 302/303/304/305/308
en TRA 270/271/345/346/413) (*) Aantal pagina’s y
Controle organisme
OCAB Producent
Nagezien □ Nagezien □ Naam : Nummer : Akkoord □ Akkoord □
Datum Technisch Dossier Datum
Naam Paraaf Stempel
Opmerkingen van het controle-organisme
Opmerkingen van de producent
Herzienings-index
Aard van de wijziging Betreffende pagina’s
Datum van de wijziging
(*) De onnodige vermeldingen doorhalen
OCAB-OCBS
Vereniging zonder winstoogmerkRavensteinstraat 4B 1000 Brussel
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
3
TD pagina 2A
Verklaring van de aanvrager
Het bijgevoegd Technisch Dossier (TD) maakt integraal deel uit van de aanvraag van de maatschappij:
Nr. producent bij OCBS : Naam : Straat en nr. : Postcode en plaats : Land : Tel. : Fax : E-mail :
voor machtiging tot gebruik van het BENOR-merk voor de productie van staven/draden /gelaste wapeningsnetten / tot vlakke panelen samengestelde wapeningen / tralieliggers(*) conform NBN A 24-301/-302/-303/-304 (*), TRA 270/271/345/346/413 (*) en PTV 302/303/304/305/307/308 (*) uitgevoerd op de productiezetel:
Naam : Straat en nr. : Postcode en plaats : Land : Tel. : Fax : E-mail :
De producent-aanvrager verklaart dat de inhoud van dit technisch dossier volledig overeenkomstig is met de reële situatie bij de productiezetel op datum van de handtekening.
Gedaan te
De
De producent-aanvrager, (*) De onnodige vermeldingen doorhalen
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
4
TD pagina 2B
Verklaring van de producent
Jaarlijkse aanpassing Het bijgevoegd Technisch Dossier (TD) maakt integraal deel uit van de overeenkomst van de maatschappij :
Nr. producent bij OCBS : Herzieningsindex van het TD : Naam : Straat en nr. : Postcode en plaats : Land : Tel. : Fax : E-mail :
voor machtiging tot gebruik van het BENOR-merk voor de productie van staven/draden/ gelaste wapeningsnetten / tot vlakke panelen samengestelde wapeningen / tralieliggers (*) conform NBN A 24-301/-302/-303/-304 (*), TRA 270/271/345/346/413 (*) en PTV 302/303/304/305/307/308 (*) uitgevoerd op de productiezetel:
Naam : Straat en nr. : Postcode en plaats : Land : Tel. : Fax : E-mail :
De producent-aanvrager verklaart dat de inhoud van dit technisch dossier volledig overeenkomstig is met de reële situatie bij de productiezetel op datum van de handtekening.
Gedaan te
De
De producent,
(*) De onnodige vermeldingen doorhalen
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
3
TD pagina 3
Inhoudstafel
Herzienings
index TD Titel Paginanr. Datum
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
4
TD pagina 4
Voorstelling
Het verkoopsorganisme
Naam :
Volledig adres : Straat nr.
Postcode Plaats
Land
Telefoon :
Fax :
E-mail :
Organogram van de producent
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
5
TD pagina 5
Personeel kwaliteit
Verantwoordelijke kwaliteitsdienst
Titularis Plaatsvervanger
Naam
Voornaam
Functie
Paraaf
Handtekening
Controlepersoneel
Naam et Voornaam Functie Paraaf Handtekening1
2
3
4
5
Extern labo dat gebruikt wordt door de producent, in het kader van zijn zelfcontrole, voor proeven die hij niet in zijn eigen labo kan uitvoeren of in het geval er zich in zijn labo een panne voordoet.
Naam Adres Telefoon Fax
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
6
TD pagina 6
Organisatie van de productie en van de verzending
Plan dat de inplanting van de machines en hun benaming weergeeft, de opslagruimtes, de beweging van het staal tijdens de productie, ...
Markering (elk veld en dwarsdoorsnede) (voor staven en draden)
Model van etiket (eventueel verschillende kleuren).
Model van leveringsborderel.
Geplooide netten of panelen, vervaardigd rond buigdoornen met een kleinere diameter dan in de norm voorgeschreven, worden buiten BENOR-merk geleverd. (*)
(*)De onnodige vermeldingen doorhalen
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
7
TD pagina 7
Gebruikt staal (staven/draden) BE 500 (E)(R)(T)S – DE 500 BS
Staalnr.
Aard bobijn,…
Kenmerken van de grondstoffen Oorsprong producent Re
min/max Rm
min/max Andere Diametergamma
A1
A2
BE 500 S
Staalnr.
Aard knuppels,…
Kenmerken van de grondstoffen Oorsprong producent
Afmetingen
B1
B2
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
8
TD pagina 8
Gebruikt staal (netten/vlakke panelen/tralieliggers)
Staal nr.
Aard : Staven, rollen
Kenmerken van de grondstoffen Herkomst :
producent + eventueel nr. OCBS
Staalsoort : BE 500 S, BE 500
(E)(R)(T)S, DE 500 BS Diametergamma
A1
A2
B1
B2
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
9
TD pagina 9
Productiemiddelen (staven/draden)
Machines /Wals
Beschrijving: merk, type, proces, bouwjaar,…
Nr. basisstaal (*)
Thermische behandeling
Afgewerkt product
Diameter gamma
Staaltype Vorm : staven,
bobijnen
M1
M2
(*) zie tabel "gebruikt staal"
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
10
TD pagina 10
Productiemiddelen (netten/vlakke panelen/tralieliggers)
Machine nr. Mi
Beschrijving : merk, type, process bouwjaar,…
Nr basisstaal (*)
Vorm : staven/ rollen
diameter gamma
Staaltype Thermische behandeling
M1
M2
(*) zie tabel "gebruikt staal"
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
11
TD Bijlage 1a
BEMONSTERINGSPLAN Staven/Draden
Gecontroleerde parameter
Controlemiddel Controlefrequentie
Scheikundige samenstelling
Conventionele dwarsdoorsnede
Mechanische eigenschappen
Heen- en terugbuig weerstand
Geometrie
…
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
12
TD Bijlage 1b
BEMONSTERINGSPLAN Netten/Vlakke panelen
Gecontroleerde parameter
Controlemiddel Controlefrequentie
Scheikundige samenstelling
Conventionele dwarsdoorsnede
Mechanische eigenschappen langsdraad
Mechanische eigenschappen dwarsdraad
Heen- en terugbuig weerstand op langsdraad
Heen- en terugbuig weerstand op dwarsdraad
Afschuifweerstand van de lassen
Geometrie van de draden
Afmetingen net/paneel
…
Stempel OCBS
Paraaf controle-organisme Paraaf producent Herziening nr. Datum Pagina
13
TD Bijlage 1c
BEMONSTERINGSPLAN Tralieliggers
Gecontroleerde parameter T
ype
1
Typ
e 2
Typ
e 3
Controlemiddel Controlefrequentie
Afmetingen tralieligger
x x x
Geometrie bovenste draad
x
Geometrie onderste draden
x
Heen – en terugbuig weerstand bovenste
draad x
Heen – en terugbuig weerstand onderste
draden x
Scheikundige samenstelling
bovenste draad x
Scheikundige samenstelling
onderste draden x
Mechanische eigenschappen bovenste draad
x
Mechanische eigenschappen onderste draden
x
Treksterkte van alle draden
(behalve voormelde) x x x
Conventionele dwarsdoorsnede van alle draden
x x x
Afschuifweerstand van de gelaste knopen
x x x
…
Document OCAB n° 592/4
• Proposed by the Technical Office N° 1 on February 23, 2016 • Approval by the Board of Directors on March 11, 2016 592-4e
APPLICATION OF BENOR MARK IN
SECTOR OF THE REINFORCING STEEL PRODUCTS
METHODS OF ASSESSMENT APPLICABLE TO
“USERS OF THE MARK” - ROLLERS, WIRE MAKERS, PRODUCERS OF WELDED MESHES, REINFORCEMENTS ASSEMBLED IN THE FORM OF
PLANE PANEL OR LATTICE GIRDERS
TECHNICAL DOSSIER
Document OCAB n° 592/4 Page2 of 19
BARS/WIRES
MESHES/PANELS
LATTICE GIRDERS
(Appendix: 1 file)
TECHNICAL DOSSIER
The present note constitutes a guide for the establishment of a technical dossier in accordance with documents TRA 270, 271, 345, 346 and 413 and their A.1.1 paragraph in particular. The groundwork of this file is given in appendix. Only pages 1 and 2 are imposed: - Version “A” (1A pages and 2A) is used for the initial technical dossier; - Version “B” is used for the annual updates. The inspection body must be informed of each modification.
Page of the DT
A. Flyleaf with mention of: DT 1A-1B
A.1. TECHNICAL DOSSIER MESH/PANEL/LATTICE GIRDER. A.2. Reference documents: NBN A 24-301/-302/-303/-304, PTV 302/303/304/305/307/308
and TRA 270/271/345/346/413. A.3. Number of pages. A.4. Statute of the file: project, final. A.5. Inspection body: checking, agreement, date, seal, signature.
Document OCAB n° 592/4 Page3 of 19
A.6. OCAB: checking, agreement, date, seal, signature (only p. DT 1A). A.7. Producer: name and producing number with the OCAB, date, seal, signature. A.8. Remarks inspection body. A.9. Remarks of producer.
A.10. Remarks of OCAB (only p. DT 1A).
A.11. Table taking again all the modifications of the technical dossier: object, revision number
of the modification, page(s) concerned(s), date of the modification (only p. DT 1B).
B. Declaration of the producer. DT 2A-2B
C. Contents. DT 3
D. Complete Designation of the organization of sale (name, compete address, n° Tel., n° fax, E-mail,…) DT 4
E. Nomination the persons in charge of the quality controls and their substitute (name and function). DT 5 A flow chart of the company can possibly be joined. DT 4
F. Presentation: DT 6
Description of the organization of the production as well from the administrative point of view as technical.
G. Identification: DT 6
1. Marking (bars and wires)
Drawing taking again the geometry of each field of rib and a transverse section in the bar or the wire.
2. Labels
A model of each type at least taking again the information included in the § A.1.5 of the corresponding TRA.
Document OCAB n° 592/4 Page4 of 19
H. Delivery Form: DT 6
Model with at least beginning:
- Initials BENOR with distinctive number of the user of the mark (X) Bars/Wire/Meshes Panels Lattice girders
(X) (X) (X)
NBN A 24-301 NBN A 24-301 + PTV 308 NBN A 24-301 + PTV 305
Remark: For the bars, if an alternative profile is used, mention “NBN A 24-301” is replaced
by “NBN A 24-301 + PTV 307”
- Name of the producer; - Increasing Sequence Number; - Qualitative and quantitative complete designation of the delivery; - Delivery Date; - Name and addresses of the customer and place of delivery; - All references of the customer order.
I. Steels used
Designation of various qualities of steel, the various producers, all the diameters used and their quality BENOR or not. DT 7
J. Production
Description of all the means of production used. DT 8 K. Sampling Design:
In agreement with the TRA 270/271/345/346/413 § B.1.2., the sampling design must define the types and frequencies of the sampling, check operations and recording of controls. In the case of the use, for the calculation of FR, of the simplified formula FR =g.h/c (according to the methods described in the normative documents of application), the validated value of G-value must be declared in the DT and a file of validation approved - by the inspection body - must be available.
Bars/wire DT appendix 1a Lattice/panels plans DT appendix 1b Lattice girders DT appendix 1c
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
1
DT page 1 A
OCAB - OCBSnon-profit-making association
Rue Ravensteinstraat, 4 B-1000 Brussels
INITIAL TECHNICAL DOSSIER Project □ Final □
Bars/Wire/Lattice/Panels/Lattice girders (NBN A 24-301/-302/-303/-304, PTV 302/303/304/305/308
and TRA 270/271/345/346/413) (*) Number of pages y
Inspection body
OCAB Producer
Checked □ Checked □ Name: Number: Agreement □ Agreement □
Date Technical Dossier
Date:
Name Initials
Seal
Remarks of the inspection body
Remarks of the producer
Remarks of the OCAB
(*) To Cross Out the useless mentions
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
2
DT page 1 B
TECHNICAL DOSSIER: UPDATE Project □ Final □
Bars/Wire/Lattice/Panels/Lattice girders (NBN A 24-301/-302/-303/-304, PTV 302/303/304/305/308
and TRA 270/271345/346/413) (*) Number of pages y
Inspection body
OCAB Producer
Checked □ Checked □ Name: Number: Agreement □ Agreement □
Date Technical Dossier Date
Name Initials
Seal
Remarks of the inspection body
Remarks of the producer
Revision Number
Object of the modification Page (S) concerned (S)
Date of the modification
(*) To Cross Out the useless mentions
OCAB - OCBSnon-profit-making association
Rue Ravensteinstraat, 4 B-1000 Brussels
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
3
DT page 2 A
Declaration of the applicant
The technical dossier (DT) herewith forms integral part of the request of the company:
Producer N° with the OCAB: Name: Street and n°: Postcode and locality: Country: Tel.: Fax: E-mail:
of authorization of use of BENOR MARK for the production of bars/wires/steel fabrics/reinforcements assembled in the form of plane panels/lattice girders (*) in accordance with NBN A 24-301/-302/-303/-304 (*), with the TRA 270/271/345/346/413 (*) and the PTV 302/303/304/305/307/308 (*) carried out in its seat of manufacturing:
Name: Street and n°: Postcode and locality: Country: Tel.: Fax: E-mail:
The petitioning producer declares that the contents of this technical dossier are entirely in conformity with the real situation with the seat of manufacturing at the date of the signature.
Done in
The petitioning producer, (*) To Cross Out the useless mentions
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
4
DT page 2 B
Declaration of the producer
Annual Update The technical dossier (DT) herewith formed integral part of the convention of the company:
Producer N° with the OCAB: Revision Number of the DT: Name: Street and n°: Postcode and locality: Country: Tel.: Fax: E-mail:
of authorization of use of BENOR MARK for the production of bars/wires/steel fabrics/reinforcements assembled in the form of plane panels/lattice girders (*) in accordance with NBN A 24-301/-302/-303/-304 (*), with the TRA 270/271/345/346/413 (*) and the PTV 302/303/304/305/307/308 (*) carried out in its seat of manufacturing:
Name: Street and n°: Postcode and locality: Country: Tel.: Fax: E-mail
The producer declares that the contents of this technical dossier are entirely in conformity with the real situation with the seat of manufacturing at the date of the signature.
Done in
The producer,
(*) To Cross Out the useless mentions
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
3
DT page3
Tables Of Content
Revision
Number DT Title N° page Date
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
4
DT page4
Presentation
The organization of sale
Name:
Complete Address: Street n°
Postcode Locality
Country
Telephone:
Telefax:
E-mail:
Flow Chart of the producer
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
5
DT page5
Staff quality
Responsible service quality
Manpower Substitute
Name
First Name
Function
Initials
Signature
Staff of control
Name and First Name Function Initials Signature
1
2
3
4
5
External Laboratories used by the producer, within the framework of its autocontrol, for tests which it cannot carry out in his own laboratory or in the event of failure of this one.
Name Addresses Telephone Telefax
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
6
DT page6
Organization of the production and forwarding
Plan taking again the machine installation of with their designation, sections storage, advance of steels during the production, …
Marking (each field and transverse section) (for the bars and wire)
Model of label (possibly various colours).
Model of delivery form.
Bent lattices/panels, carried out with mandrel diameters lower than the standard, will be provided without BENOR MARK. (*) (*) To Cross Out the useless mentions
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
7
DT page 7
Steels used (bars/wire) BE 500 (E)(R)(T)S - DE 500 BS
N° steel
Nature: coils,…
Characteristics of the raw materials Source:
producer Re min/max
Rm min/max
Others Range of diameters
A1
A2
BE 500 S
N° steel
Nature: billets,…
Characteristics of the raw materials Source:
producer Dimensions
B1
B2
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
8
DT page 8
Steels used (lattice/panels/lattice girders)
N° steel
Nature: Bars, coils Characteristics of the raw materials Source:
producer + possible n° OCAB Grade: BE 500 S, BE 500
(E)(R)(T)S, DE 500 BS Range of the diameters
A1
A2
B1
B2
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
9
DT page 9
Means of production (bars/wire)
N° of machine rolling mill Mi
Description: mark, standard, process, year of construction, …
N° steel of origin (*)
Heat Treatment
End product
Range of diameters
Type of steel
Form: reels/bars
M1
M2
(*) see table “steels used”
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
10
DT page 10
Means of production (lattice/panels/lattice girders)
N° of machine
Mi
Description: mark, standard, process year of construction, …
N° steel of origin (*)
Form: wind bars
Range of diameters
Type of steel Heat
Treatment
M1
M2
(*) to see table “steels used”
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
11
DT Annexe 1a
SAMPLING DESIGN Bars/Wire
Controlled Parameter Method of control Frequency of control
Chemical Composition
Conventional Section
Mechanical Properties
Resistance to the rebending
Geometry
…
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
12
DT Annexe 1b
SAMPLING DESIGN Meshes/Panels
Controlled Parameter Method of control Frequency of control
Chemical Composition
Conventional Section
Mechanical Properties of the longitudinal wire
Mechanical Properties of the transverse wire
Resistance to the rebending on the longitudinal wire
Resistance to the rebending on the transverse wire
Shear Strength of the welds
Geometry of the wires
Dimensions lattice/panel
…
Seal of the OCAB
Org Initials. of control Initials producing Revision n° Date Page
13
DT Annexe 1c
SAMPLING DESIGN Beams lattice
Controlled Parameter T
ype
1
Typ
e 2
Typ
e 3
Means of control
Frequency of control
Dimensions beam lattice X X X
Geometry higher wire X
Geometry lower wires X
Resistance to the rebending higher wire X
Resistance to the rebending lower wires X
Chemical Composition wire superiors X
Chemical Composition lower wires X
Mechanical Properties of the higher wire X
Mechanical Properties of the lower wires X
Tensile Strength of all the wires
(except those above) X X X
Conventional Section of all the wires X X X
Shear Strength of welded nodes X X X
…