tzw803+ 8x1 vga/xga & audio switcher that the built-in led of key 1 on the front of the unit...

TZW803+ M 06/04/07

TZW803+ 8x1 VGA/XGA & AUDIO SWITCHER

ELPRO Video Labs s.r.l.St.da della Pronda, 45/B 10142 Torino ITALY Tel.+39 0117701583 – Fax +39 011703751

1

• Amplified output for SVGA 20mt cable

• Can be connected in cascade

• Autoswitching, autosequencing and mute

• 400 MHz bandwidth

• Remote control with dry contacts

• Tally

• RS232 by computer

• Internal power unit

INSTALLATION AND USE OF THE TZW 803+ UNIT

INDEX

1.0Overview2.0Power supply3.0Settings4.0Installation5.0Local control6.0Control by dry contacts and tally7.0Ancillary functions8.0Control from computer9.0CASCADE option and settings10.0Technical data11.0Notes

Please read this manual carefully before installing the TZW 803+.

The manufacturers shall not be answerable for damage resulting from the use, proper or otherwise, of their products. Product data and specifications are subject to change without prior notice.



2

1.0 OVERVIEW Thank you for choosing this product. Check that the following items are included in the packaging:


− The TZW803+ unit

The TZW803+ unit is an 8X1 Switcher for VGA/XGA signals with associated stereo audio. Excellent technical characteristics and generously scaled components make this unit particularly suited for harsh, continuous use. The main areas of application include showrooms, airports, museums, large department stores and hotels.

− The mains cable

- IR control

- sub-D 15v.m. vol. conn. with boot code ADP 010

- This handbook and the conformity certificate



4

TZW803+ CONNECTION – 6 SOURCES 1 DESTINATION

2.0 POWER SUPPLY

The TZW803+ unit must be powered at 230 Vac 50Hz using the cable provided. The cable must be fitted in the related panel plug on the left at the back of the unit.The panel plug is equipped with a fuse-holder for 5X20 fuses. In the event of fuse burnout, the replacement fuse must be of the same value, as specified on the back of the unit (T 0.5A).

ATTENTIONAll operations must be performed by specialized personnel

who must be made aware of electric shock hazards.

In some countries the current plug must be adapted to comply with local standard types. Wires can be identified according to the following code:

-Brown PHASE (Marked with the letter L, may be red)-Blue NEUTRAL (Marked with the letter N, may be black )-Yellow/Green GROUND (Marked with the letter E, may be green)

ATTENTIONGrounding is compulsory

The TZW803+ can be ordered for powering at 115Vac 60Hz. The setting is made in factory and cannot be modified by the customer.


3.0 SETTINGS

The TZW 803+ switcher has a set of 6 dip-switches, accessible from the back of the unit, that can be used to set and customize the unit. Five dip-switches are used to set CASCADE functioning while the sixth enables or not the external IR remote control.In pos. ON, default factory-set, it enables the IR remote control.

Refer to chapter 9.0 for a description of the settings.

4.0 INSTALLATION

a) Make sure that the switch on the back of the TZW803+ is set to OFF (O). Power the device as indicated in chapter 2.0.

b) Connect the 8 sources to the sub-D 15 p. f. HD connectors with good quality VGA m/m cables.

c) Connect the destination to the sub-D 15 p. f. HD conn. with a VGA cable with a length of not more than 20 meters.

ATTENTIONFor more than 20mt cables, it is advisable to insert

an Elpro INBOX/4 type booster

Use of Elpro cables is recommended in order to exploitthe characteristics of the compensation circuit to the full.

d) Connect the stereo audio in output from the 8 sources to the 8 RCA sockets ( AUDIO IN).

e) Tap the stereo audio in output from the RCA socket (AUDIO OUT) and / or from the balanced audio output (BALANCED) and connect it to a sound amplification and broadcast system.

f) Set the switch on the back of the unit to ON (I). Check that the built-in led of key 1 on the front of the unit switches on.



6

5.0 LOCAL CONTROL

The TZW803+ switcher can be controlled using the 8 keys on the front panel of the unit.

Switching on of the built-in led of the button indicates which source is switched to the output.

At power-on, source 1 is switched automatically.

6.0 CONTROL BY DRY CONTACTS AND TALLY

The TZW803+ is controlled using 8 dry contacts connected to the sub-D 25 v.f. REMOTE connector on the back of the machine.Eight external signals are provided to light on the 8 tally leds connected as indicated in the figure below.


1 TALLY 1 14 INPUT 12 TALLY 2 15 INPUT 23 TALLY 3 16 INPUT 34 TALLY 4 17 INPUT 45 TALLY 5 18 INPUT 56 TALLY 6 19 INPUT 67 TALLY 7 20 INPUT 78 TALLY 8 21 INPUT 89 22 TIME

10 23 AUTOSW11 AUTOSEQ 24 +5 VDC12 RS232RX 25 GND13 MUTE - -

HIGH EFFICIENCY

LEDS

The correspondence between the code sent by the computer and the function activated on the TZW803+ is given in the table below.

Pin #12Sub-D FUNCTION

31h INPUT 132h INPUT 233h INPUT 334h INPUT 435h INPUT 536h INPUT 637h INPUT 738h INPUT 8

Pin #12Sub-D FUNCTION NOTE

52h autosequence control active only for single unit

53h autoswitching control active for single unit and in cascade

54h mute video control active for single unit and in cascade

55h mute audio control active for single unit and in cascade

56h mute audio+video control active for single unit and in cascade

The AUTOSEQUENCING, AUTOSWITCHING and MUTE commands are de-activated repeating the commands or sending the code of another command.The AUTOSEQUENCING AUTOSWITCHING, and MUTE commands are de-activated pressing a key on the built-in keyboard.In this case, the input of the key pressed will be switched on the output.



10

7.0 ANCILLARY FUNCTIONSThe TZW803+ switcher features three ancillary functions that are activated with 3 dry contacts connected to the sub-D 25 v. f. REMOTE connector on the back of the machine.The function remains active as long as the related pin is at ground (pin 25).

7.1 AUTOSEQUENCINGAll 8 sources are switched on the output at a rate of 4 or 10 seconds each.The time of 4 or 10 seconds is established by pin 22 (TIME) of the sub-D 25 v. f. REMOTE conn. on the back of the machine.Contact open is for 4 sec. timeIf an input is selected during autosequencing (using the keyboard, remote control or PC), the input selected is connected and the autosequencing function restarts from that input.

7.2 AUTOSWITCHINGThe active source is routed on the VGA/XGA output.If more than one source is active, source 1 has the highest priority followed by source 2 and so on.If an input is selected during autoswitching (using the keyboard, remote control or PC), the input selected is connected and the autoswitching function is interrupted.

7.3 RGB MUTENo source is switched on the output.This capability is particularly useful when the images to be displayed on the computer are to be prepared between one switching and the next.

ATTENTIONAUTOSEQUENCING, AUTOSWITCHING and RGB MUTE

are mutually exclusive. Priority is as follows:RGB MUTEAUTOSWITCHINGAUTOSEQUENCING

With the CASCADE option active, the three ancillary functions controlled by dry contacts are excluded.

However, Autoswitching and Mute can be controlled from the computer.



8

8.0 COMPUTER CONTROL

The TZW803+ switcher can be computer controlled as regards all the functions described, simply by sending a hexadecimal character

Transmission is RS 232, 8 bits,1 stop bit , no parity.Baud rate is 9600.The character must be sent to pin #12 of the sub-D 25 v. f. REMOTE conn. connected on the back of the machine. The ground is pin #25.


1 TALLY 1 14 INPUT 1








9 22 TIME

10 23 AUTOSW

11 AUTOSEQ 24 +5 VDC

12 RS232RX 25 GND

13 MUTE - -

Pin # 22Sub - D

TIME

1 (free) 4 sec.0 (GND) 10 sec

9.1 COMMANDS IN CASCADEIn CASCADE functioning, the source to be switched on the output can be selected using the built-in keyboard of each unit or using the computer.

ATTENTIONIn CASCADE functioning, pins 12 (RS232) and 25 (GND) of the

REMOTE connectors must be joined together and connected to thetransmitted signal of the host computer

Pin #12

Sub-DFUNCTION

Pin #12Sub-D FUNCTION Pin #12

Sub-D FUNCTION

31h INPUT 1 3Bh INPUT 11 45h INPUT 2132h INPUT 2 3Ch INPUT 12 46h INPUT 2233h INPUT 3 3Dh INPUT 13 47h INPUT 2334h INPUT 4 3Eh INPUT 14 48h INPUT 2435h INPUT 5 3Fh INPUT 15 49h INPUT 2536h INPUT 6 40h INPUT 16 4Ah INPUT 2637h INPUT 7 41h INPUT 17 4Bh INPUT 2738h INPUT 8 42h INPUT 18 4Ch INPUT 2839h INPUT 9 43h INPUT 19 4Dh INPUT 293Ah INPUT 10 44h INPUT 20Pin #12

Sub-DFUNCTION NOTE

52h autosequence control active only for single unit53h autoswitching control active for single unit and in cascade54h mute video control active for single unit and in cascade55h mute audio control active for single unit and in cascade56h mute audio+video control active for single unit and in cascade



12

9.0 CASCADE OPTION AND SETTINGS

The TZW803+ switcher features a CASCADE option that permits connection in series of 4 units to establish a 29x1 selector.

ATTENTIONIn the CASCADE connection, band and technical

characteristics are no longer guaranteed.In the case of CASCADE connection, the output of the first TZW803+ must be connected to input 1 of the second TZW803+ and so on.Using cables terminated with RCA plugs, connect together the LINK connectors present on the back of the unit.

CASCADE functioning is activated by setting a switch that is accessible from the back of the unit as indicated in the figure below (ENABLE CASCADE).Each unit must also be customized according to its position in the chain with the setting of another switch as indicated in the figure below.

ATTENTIONWith the CASCADE option active, the three ancillary functions are

excluded except for RGB MUTE and computer-controlled AUTOSWITCHING.

ATTENTIONThe last dip-switch (pos. 6), if set to

OFF, makes it possible to

disable reception of

the commands from the IR

remote control.


10.0 TECHNICAL DATA

Video:

Inputs :analog 700 mVpp with HDD 15p.f. Coupling :DC Crosstalk(worst case) :50 dB at 40 MHz Outputs :one, precompensated with HDD 15p.f. Bandwidth :400 MHz SYNCHRONISM :H+V separated, TTL level, high Z OTHER SIGNALS :ST, TTL level, high Z :SDA,SCL,TTL level, high Z, bidirectional

Audio:

Input Coupling :AC, unbalanced Input Impedance :47 KΩ Input level :+11 dBm Max. Gain :-0.5 dB, +6 dB on the bal. outpou Frequency response :-1 dB from 40Hz to 20 KHz Crosstalk :60 dB at 5 KHz Distortion :<0.03% at 0 dBm with 10K load Output load :10K nominal, 600 Ohm minimum Output impedance :100 Ohm Audio inputs/outputs :stereo RCA sockets

Main input :230Vac 50HzPower consumption :6VASize (WXDXH) :483X210X88Weight :2.5Kg

Operating temp. range:0÷45°Safety :according to EN60065EMC :according to EN55103-1 and EN55103-2

CE Mark



13

11.0 NOTES

This product is guaranteed for 2 years from the date of purchase.

The guarantee does not cover damage to the product causedby improper use or operations effected by third parties

For the duration of guarantee Elpro shall repair faulty units free of charge.

Faulty units must be sent with a standard waybill and CARRIAGE PAID to Elpro’s Turin works.

Repaired units shall be returned CARRIAGE FORWARD to the consignee.

Faulty units that are no longer covered by guarantee shall be repaired by Elpro EX WORKS Turin and the work shall be charged to the customer.

For any problems regarding installation of theTZW 803+call the Elpro hot line .+39 0117701583

or send an E-mail to: [email protected]



14

tzw803+ 8x1 vga/xga & audio switcher that the built-in led of key 1 on the front of the unit...

Documents