unione i&c 시스템 기술지원 팀 sparc enterprise mx000 firmware upgrade
TRANSCRIPT
UniONE I&C
시스템 기술지원 팀
Sparc Enterprise Mx000 firmware upgrade
Sparc Enterprise Mx000 firmware upgrade
목차
1. Logging into the XSCF Shell
2. Initializing the XSCF (Network 설정 )
3. Downloading the firmware file
4. Connecting to xscf web console
5. Uploading the firmware file
6. Update the xscf firmware
1. Logging into the XSCF Shell
1-1. 1-1. 로그인 창이 출력되면 “로그인 창이 출력되면 “ default”default” 를 입력합니다를 입력합니다 ..
(dafault (dafault 유저는 시리얼포트에서만 사용가능유저는 시리얼포트에서만 사용가능 ))
1-2. 1-2. 화면에 모드스위치변경에 대한 메시지가 출력되면 아래와 같이 작업합니다화면에 모드스위치변경에 대한 메시지가 출력되면 아래와 같이 작업합니다 ..
모드스위치를 “모드스위치를 “ Locked”Locked” 로 변경 로 변경 -> return-> return 을 누름 을 누름 -> 5-> 5 초간 기다림 초간 기다림 -> -> 모드스위치를 “모드스위치를 “ Service”Service” 로 변경 로 변경 -> return-> return 을 누름을 누름
1-3. 1-3. 위 작업을 완료하면 아래와 같이 위 작업을 완료하면 아래와 같이 XSCF ShellXSCF Shell 이 출력됩니다이 출력됩니다 ..
XSCF> XSCF>
1-4. 1-4. 만약 모드스위치가 만약 모드스위치가 LockedLocked 로 되어 있는 경우에는 아래와 같이 작업합니로 되어 있는 경우에는 아래와 같이 작업합니다다 ..
모드스위치를 “모드스위치를 “ Service”Service” 로 변경 로 변경 -> return-> return 을 누름 을 누름 -> 5-> 5 초간 기다림 초간 기다림 -> -> 모드스위치를 “모드스위치를 “ Locked”Locked” 로 변경 로 변경 -> return-> return 을 누름을 누름
2. Initializing the XSCF (Network 설정 )
2-1. XSCF Shell2-1. XSCF Shell 에 로그인이 되면 유저를 생성합니다에 로그인이 되면 유저를 생성합니다 ..
XSCF> adduser XSCF> adduser xscf xscf XSCF> password XSCF> password xscf xscf 암호입력 암호입력 : : xscf xscf ( ( 예예 ))XSCF> setprivileges XSCF> setprivileges xscf xscf platadm useradm fieldeng platadm useradm fieldeng XSCF> showuser xscf XSCF> showuser xscf fkl fkl 유저의 설정값 확인유저의 설정값 확인
2-2. XSCF Shell2-2. XSCF Shell 로 재 로그인합니다로 재 로그인합니다 ..
XSCF> exitXSCF> exitLogin : Login : xscf xscf Password : Password : xscf xscf XSCF> showuser XSCF> showuser 현재 유저를 확인 현재 유저를 확인 (platadm, useradm, fieldeng (platadm, useradm, fieldeng 확인확인 ))
2-3. XSCF2-3. XSCF 의 네트워크를 설정합니다의 네트워크를 설정합니다 . (. ( 예예 ))
XSCF> setnetwork xscf#0-lan#0 –m 255.255.255.0 172.16.100.64 XSCF> setnetwork xscf#0-lan#0 –m 255.255.255.0 172.16.100.64 ( ( 유저 유저 IP)IP)XSCF> setnetwork xscf#0-lan#1 –m 255.255.255.0 192.168.1.2 XSCF> setnetwork xscf#0-lan#1 –m 255.255.255.0 192.168.1.2 (FE (FE 전용 전용 IP)IP)XSCF> setroute –c add –n 0.0.0.0 –g 172.16.100.254 xscf#0-lan#0 XSCF> setroute –c add –n 0.0.0.0 –g 172.16.100.254 xscf#0-lan#0 ( ( 유저 유저 G/W)G/W)XSCF> setroute –c add –n 192.168.1.0 –m 255.255.255.0 xscf#0-lan#1XSCF> setroute –c add –n 192.168.1.0 –m 255.255.255.0 xscf#0-lan#1XSCF> showroute –aXSCF> showroute –aDestination Gateway Netmask Flags Interface172.16.100.0 * 255.255.255.0 U xscf#0-lan#0192.168.1.0 * 255.255.255.0 U xscf#0-lan#1default 172.16.100.254default 172.16.100.254 0.0.0.0 UG xscf#0-lan#0
2. Initializing the XSCF (Network 설정 )
2-4. XSCF2-4. XSCF 의 네트워크 인터페이스의 정보를 확인합니다의 네트워크 인터페이스의 정보를 확인합니다 ..
XSCF> shownetwork –a XSCF> shownetwork –a 모든 인터페이스 정보확인모든 인터페이스 정보확인XSCF> shownetwork xscf#0-lan1 XSCF> shownetwork xscf#0-lan1 XSCFU#0 XSCFU#0 의 의 LAN1LAN1 의 정보를 확인의 정보를 확인xscf#0-lan#1xscf#0-lan#1 Link encap:Ethernet HWaddr 00:0A:48:09:C9:0E inet addr:192.168.1.2192.168.1.2 Bcast: 192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:54424 errors:0 dropped:0 overruns:0 frame:0 TX packets:14369 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:20241827 (19.3 MiB) TX bytes:2089769 (1.9 MiB) Base address:0xe000
2-5. Telnet2-5. Telnet 을 활성화합니다을 활성화합니다 ..
XSCF> settelnet –c enableXSCF> settelnet –c enableXSCF> showtelnet XSCF> showtelnet Telnet status: enabled
2-6. 2-6. 네트워크 설정값을 적용합니다네트워크 설정값을 적용합니다 ..
XSCF> applynetworkXSCF> applynetworkThe following network settings will be applied:xscf#0 hostname :xscf0DNS domain name :com~생략~The XSCF will be reset. Continue? [y|n] :y
2-7. XSCF WEB 2-7. XSCF WEB 접속을 위해 접속을 위해 httpshttps 설정을 합니다설정을 합니다 . .
XSCF> sethttps -c selfsign KR Seoul local FKL FEG scf_host [email protected]> sethttps -c selfsign KR Seoul local FKL FEG scf_host [email protected] key already exists. Do you still wish to update? [y|n] :yyEnter passphrase: xscf xscfVerifying - Enter passphrase: xscf xscf
XSCF> showhttpsXSCF> showhttpsHTTPS status: disabledServer key: installed in Jun 19 17:47:13 KST 2007CA key: installed in Jun 19 17:47:12 KST 2007CA cert: installed in Jun 19 17:47:12 KST 2007CSR:-----BEGIN CERTIFICATE REQUEST-----MIIBuzCCASQCAQAwezELMAkGA1UEBhMCS1IxDjAMBgNVBAgTBVNlb3VsMQowCAYD~~ 생략 ~~85iZQdOQdBZWhT5fu6jaJPzqzFiO5tXgMPCzfmAxvM2Ecqu7tZ9z5hAmdOXDOfDGScG6FKOW/kJTji1DOEsv-----END CERTIFICATE REQUEST-----
XSCF> sethttps -c enableXSCF> sethttps -c enableThe XSCF will be reset. Continue? [y|n] :y y
2. Initializing the XSCF (Network 설정 )
3. Downloading the firmware file
3-1. Fujitsu 3-1. Fujitsu 웹 사이트에서 웹 사이트에서 firmware filefirmware file 을 다운로드 받습니다을 다운로드 받습니다 ..
http://www.fujitsu.com/global/services/computing/server/sparcenterprise/http://www.fujitsu.com/global/services/computing/server/sparcenterprise/downloads/firmware/downloads/firmware/
4. Connecting to xscf web console
4-1. Internet explorer 4-1. Internet explorer 을 열고 을 열고 xscf web consolexscf web console 에 접속합니다에 접속합니다 ..
Ex) https://192.168.1.2 (xscf Lan-ip)Ex) https://192.168.1.2 (xscf Lan-ip)
4. Connecting to xscf web console
5. Uploading the firmware file
5-1. XCP Import Menu5-1. XCP Import Menu 를 통해서 를 통해서 firmware filefirmware file 을 을 xscfxscf 에 업로드 합니다에 업로드 합니다 ..
5. Uploading the firmware file
5-2. 5-2. 찾아보기 메뉴에서 찾아보기 메뉴에서 Fujitsu Fujitsu 웹사이트에서 다운로드한 웹사이트에서 다운로드한 firmware file firmware file 을 선택합니다을 선택합니다 ..
5. Uploading the firmware file
5-3. file5-3. file 을 선택하고 업로드를 합니다을 선택하고 업로드를 합니다 ..
5. Uploading the firmware file
5-4. file5-4. file 을 선택하고 업로드를 합니다을 선택하고 업로드를 합니다 ..
6. Update the xscf firmware
6-1. 6-1. 업로드가 끝나면 업로드가 끝나면 XCP Update XCP Update 메뉴로 메뉴로 firmware updatefirmware update 를 실행합니다를 실행합니다 ..
6. Update the xscf firmware
6-2. 6-2. 아래와 같은 메뉴가 나타나면 아래와 같은 메뉴가 나타나면 updateupdate 를 클릭합니다를 클릭합니다 ..
6. Update the xscf firmware
3-1. firmware update3-1. firmware update 가 완료되면 자동으로 가 완료되면 자동으로 xscfxscf 가 가 rebootreboot 됩니다됩니다 ..
Web consoleWeb console 에 재접속 후 에 재접속 후 firmware versionfirmware version 을 확인합니다을 확인합니다 ..
1717
Sparc Enterprise Mx000 firmware upgrade