5

請勿遮蓋產品以防止過熱。

當接駁電源後，請勿放置在插座附近。

布類

:

6

our

repair centre

- As short as possible (long cords coiled up can overheat, as

well as cause tripping accidents)

- No more than one appliance should be used in one power

Do not unplug heater by grasping plug and pulling it from the outlet.

2.9 This product is equipped with a rated current for 13 amp plug, must match the rated current is greater than or equal to 13 amp power socket to match. Or may be dangerous!

objects

7

Control button

Display panel

Air outlet

Front cover

Base

Oscillation

bracket

Back cover

Power switch

Handle position

Remote control

Figure 2Figure 1

Under standby state, press

(POWER) button or press

remote controller button to

enter into High.

Under High state, press

(POWER) button or press

remote controller button

once to enter into Low.

Under Low state, press

(POWER) button or press

remote controller button

once to enter into Energy

Saving ECO.

Under Energy Saving ECO state,

press (POWER) button or press

remote controller button once

to turn off the machine.

8

OPERATING INSTRUCTION

1. Power ON When power on for the first time, the buzzer makes a long sound and then enters into Standby state. Press (POWER) button (or press remote controller button) to turn on the product and enter into High state, the LCD displays the current room temperature.

2. Work Level

S/N Operation method Display Remarks

2000W warm air working.

1200W warm air working.

Environment temperature <set temperature 2000W warm air working. Set temperature environment temperature set temperature +21200W warm air working. Environment temperature >set temperature +2Stop working, the fan stops 15s later.

Fan stops 15s later, LCD displays the remained time of fan delay. Timing ON can not be set during countdown period.

1

2

3

4

Chassis Installation: Attached the chassis after its split (Figure 1), thenalign the screw holes of the fuselage and the screw holes in the chassisat the bottom (Figure 2) to make a complete fit, then insert the butterfly screw and twist clockwise to complete the installation!

3. Timing ON/OFF

Under ON/OFF state, press the (TIMER) button (or remote controller

button) to enter into the timing check interface, LCD displays the remained

time and flashes at 1Hz frequency (default: 0), exit the check interface if it is

not operated within 3s without changing the Set Time; press the or

button (or remote controller or button) under check state to change the

Set Time, and refresh the Set Time. Set Time setting range 0~24h, 1h each

time. Set Time precision:

±70s /h. Set Time reaches the ON/OFF, buzzer does not make sound, enter

into High/OFF mode.

4. Temperature Control

Under ON state, press (increase the set temperature) or (decrease

the set temperature) button to increase or decrease the set temperature Ts

(5~35

temperature Ts , it turns off the heating element and fan, display does not

temperature Ts-2 , it works at corresponding work level.

After power on and start the product for the first time, it does not identify the

temperature control, and then enter into the temperature control state 2min

later.

5. OSC. Function

Press the (OSC) button (or remote controller button) to turn on the

OSC function.

Under heating state, if it stops heating for temperature control and protection,

OSC will immediately stop.

The default is no OSC function after starting, the OSC function is not

memorized after turning off.

6. Temperature Sensor Short Circuit, Open Circuit Protection

Function

Under any mode, temperature sensor has short circuit protection, LCD flashes

E1 at 1Hz frequency, and it is invalid to operate any button.

Under any mode, temperature sensor has open circuit protection, LCD flashes

E2 at 1Hz frequency, and it is invalid to operate any button.

9

7. Safety Protection

Under ON state, all outputs will be turned off when indoor environment

temperature TH exceeds 50 , all LED indicators flashes for 75s at 1Hz

frequency, the product can not be started within 75s, and any button and

timing OFF are invalid, if the indoor environment temperature is <50 , it does

not exit the protection, the product will automatically exit protection state and

enter into standby state after power on again.

8. Dump Protection

Under any mode, if the product is dumped, the product will stop heating, the

fan stops 15s later, LCD flashes E3 at 1Hz frequency, and it is invalid to operate

any button.

a repair centre

10

Please repair the heater and replace parts by Midea customer centre.

and

11

burned when getting near heater.

Do not

Do not

Do not

do not

switch

to avoid any harzard

In order to avoid overheating, do not cover the heater.

Heater should not located immediately below a socket-outlet.

DISPOSAL:

Do not dispose of electrical appliances as unsorted municipal waste,

use separate collection facilities. Contact your local government for

information regarding the collection systems available. If electrical

appliances are disposed of in landfills or dumps, hazardous

substances can leak into the groundwater and get into the food chain,

damaging your health and well-being.

12