vibe slick matrix micro amplifier manual

MATR IX

InstructionManual

Slick Stereo 2Model: SLICKSTEREO2-V1

Slick Stereo 4Model: SLICKSTEREO4-V1

Slick Channel 5Model: SLICKCH5-V1

Slick Bass 1Model: SLICKBASS1-V1

2

OWNERS MANUAL

WARNING

ATTENTION

3

LIMITED WARRANTY

www.vibeaudio.co.uk/warranty

WHAT IS NOT COVERED

INTERNATIONAL WARRANTY www.vibeaudio.co.uk/warranty

WARNING

COPYRIGHT

4

MOUNTING GUIDELINES

POWER CONNECTIONS

POWER CABLE

Chassis ground

Remote turn on

Fuse close to battery

Battery

5

CONNECTIONS

GROUND CABLE

REMOTE TURN ON CABLE

RCA CABLES

Length of Rung

Current demand 0 – 4 Ft 4 – 7 Ft 7 – 10 Ft 10 – 13 Ft 13 – 16 Ft 16 – 19 Ft 19 – 22 Ft 22 – 28 Ft

0–20 amps 14 12p 12 10 10 8 8 8

20–35 amps 12p 10 8 8 6 6 6 4

35–50 amps 10p 8 8 6 4 4 4 4

50–65 amps 8p 8 6 4 4 4 4 2

65–85 amps 6p 6 4 4 2 2 2 0

85–105 amps 6p 6 4 2 2 2 2 0

105–125 amps 4p 4 4 2 0 0 0 0

125–150 amps 2p 2 2 0 0 0 0 0

AWG to Metric and Imperial Conversion Chartcross sectional area

mmmmhcnIrebmuNGWAWW 2

5.3552.8523.004.2453.7982.016.3345.6852.027.6238.5922.031.1291.5402.048.6126.4281.053.3111.4261.065.0166.3441.0763.862.3821.0836.619.2411.0962.595.2201.001

4 – 7 Ft 7 – 10 Ft 10 – 13 Ft 13 – 16 Ft 16 – 19 Ft 19 – 22 Ft 22 – 28 F

6Slick Stereo 2

TERMINALS AND CONNECTIONS

1. Low level input

2. Low level output

3. Gain control

4. Crossover mode select switch

5. Crossover frequency control

6. Power / protect LED

7. Power terminals

8. Speaker terminals

1 3 5

2 4 6

8 7

STEREO WIRING CONFIGURATION

BRIDGED WIRING CONFIGURATION

7

2 OHM MINIMUM

4 OHM MINIMUM

Slick Stereo 2

8Slick Stereo 4


1. Low level input

2. Front gain control

3. Front crossover frequency control

4. Rear gain control

5. Rear crossover mode select switch



8. Power terminals


1 3 5

2 4 6

9 8 7

9Slick Stereo 4

4 CHANNEL WIRING CONFIGURATION

3 CHANNEL WIRING CONFIGURATION

2 OHM MINIMUM

2 OHM MINIMUM

2 OHM MINIMUM

4 OHM MINIMUM

10Slick Channel 5


1. Low level input

2. Front gain control

3. Front crossover frequency control

4. Rear gain control

5. Rear crossover mode select switch


7. SUM / SUB input

8. Subwoofer gain control


11. Remote control input socket

12. Power terminals


1 2 4

78

9

3 5

1011

1213 6

S

S

11Slick Channel 5

SINGLE SUBWOOFER WIRING CONFIGURATION

DUAL SUBWOOFER WIRING CONFIGURATION

4 OHM MINIMUM

4 OHM MINIMUM 2 OHM MINIMUM

4 OHM MINIMUM


4 OHM MINIMUM

12Slick Bass 1


1. Low level input

2. Remote control input socket

3. Gain control

4. Bass boost select switch



8. Power terminals


1

2

3 579 8

4 6

13Slick Bass 1

SINGLE SUBWOOFER WIRING CONFIGURATION

DUAL SUBWOOFER WIRING CONFIGURATION

2 OHM MINIMUM


14

SETUP GUIDE

following setup routine:

The setting of the crossover will depend on what kind of speaker you are installing.

Note: The smaller the speaker, the less bass it can handle.

Note: By using the crossovers correctly you will not only lengthen the life of your speakers butyou will also get better performance from them.

15

SPECIFICATIONS

UK TECHNICAL ENQUIRIES

INTERNATIONAL TECHNICAL ENQUIRIES

www.vibeaudio.co.uk/contact

Call 09067031420

2 Channel2.3” (58mm)7.9” (201mm)6.4” (163mm)2 x 75 watts2 x 100 watts1 x 200 watts

4 x 75 watts4 x 100 watts

N/AN/A

2 x 200 watts 1 x 400 wattsN/A N/A 1 x 600 watts

400 watts 800 watts 1200 watts

20Hz - 20kHz 20Hz - 20kHz 10Hz - 500Hz0.1% 0.1% 0.1%HPF/LPF/FLAT HPF/LPF/FLAT LPF/Subsonic

50Hz - 750Hz 50Hz - 750Hz 40Hz - 220Hz

2.3” (58mm)10.3” (261mm)6.4” (163mm)

2.3” (58mm)8.8” (218mm)6.4” (163mm)

4 Channel Mono Bass Amp

4 x 90 wattsN/A1 x 300 watts1 x 515 watts

1750 watts

20Hz - 20kHz20ARecommended fuse 40A 60A 80A

0.1%HPF/LPF/FLAT

50Hz - 200Hz

2.3” (58mm)16.5” (420mm)6.4” (163mm)

5 Channel

THD

Model: DELTABOXLC-V1

vibe slick matrix micro amplifier manual

Documents