アイド縫合針-1308new - マニー株式会社 mani · me60 cutting edge 60㎜1.18
TRANSCRIPT
SE - MH 28 LL
SE
M
Example
Eye shape
Spring Eye NE Normal Eye FE French Eye(Double Eye)
*Additional code to be added only for specific items
F=Fine L=Thick LL=Extra thick
1
1 2 3 4 5
Point shape2
Curvature3
Number4
Additional information*5
Cutting edge(Inside cutting edge)
W Reverse trapezoid spatula
S Straight
E 3/8 circle 135
F 5/8 circle 225
K 1/4 circle 90
G 7/16 circle 158
J 4/5 curved
I 5/16 circle 113
H 1/2 circle 180
L 1/2 curved
T Taper point
※
※
Z Trapezoid spatula
B Blunt point N Reverse cutting(Outside cutting edge)
R Trocar
This code to be used onlyfor length smaller than 13mm
※Available for limited items only.
1
Cutting Edge
Suture-entrance avoidssuture-cutting.
Rounded edge for avoidingtissue-damage.
Sharp edge for good penetration.Safe bladish point.
Cross-lapped polishing(except small sizes) forgood penetration.
Pressed faces for smoothpenetration.
Spring Eye
Taper Point
Rounded peak eliminates unnecessarydamage by needle-holder.
Taper point minimizespenetration resistance.
Strong raw-material foranti-bending.
Smooth surface.
Suture-groove for avoidingtissue-dragging.
Smooth eye for avoidingsuture-damage.
Eye Edge
Taper Point
If the portion close to the spring eye or the needlepoint is held with a needle-holder, the quality may deteriorate such as needle or thread breakage, etc. Make sure to hold it from one-third to one-half the distance from the end of the thread held to the needlepoint.
Length
Diameter
Point shape
Eye shape
MANI SPRING EYED NEEDLES prevent tissue-damage and tissue-dragging by rounded eye-edge and suture-groove.Additionally, reduce damage of sutures by smoothsuture-entrance of spring eye.
Succeeded in producing 18-8 stainless steel surgical needles for the first time in the world.
2
3
CurvatureOrder Code Specification
Note Ref. CurvatureOrder Code Specification
Note Ref.Eye Type Shape Length Diameter Eye
Type Shape Length Diameter
1/2Circle(180°)
SE-NE-FE-
MH13 Cutting edge 13 ㎜ 0.53 ㎜
1
5/8Circle(225°)
SE-NE-FE-
MF28LL Cutting edge 28 ㎜ 0.98 ㎜ Extra thick
6
MH15 Cutting edge 15 ㎜ 0.53 ㎜ MF32LL Cutting edge 32 ㎜ 0.98 ㎜ Extra thickMH18 Cutting edge 17.5 ㎜ 0.58 ㎜ MF36LL Cutting edge 36 ㎜ 1.18 ㎜ Extra thickMH21 Cutting edge 21 ㎜ 0.68 ㎜ MF40LL Cutting edge 40 ㎜ 1.28 ㎜ Extra thickMH24 Cutting edge 24 ㎜ 0.68 ㎜ MF45LL Cutting edge 45 ㎜ 1.28 ㎜ Extra thickMH28 Cutting edge 28.5 ㎜ 0.78 ㎜ MF50LL Cutting edge 50 ㎜ 1.28 ㎜ Extra thickMH32 Cutting edge 32.5 ㎜ 0.78 ㎜ MF55LL Cutting edge 55 ㎜ 1.28 ㎜ Extra thickMH36 Cutting edge 36.5 ㎜ 0.88 ㎜ MF60LL Cutting edge 60 ㎜ 1.38 ㎜ Extra thickMH41 Cutting edge 41 ㎜ 0.98 ㎜ MF65LL Cutting edge 65 ㎜ 1.38 ㎜ Extra thickMH45 Cutting edge 45 ㎜ 1.08 ㎜
StraightSE-NE-FE-
MS13 Cutting edge 13 ㎜ 0.53 ㎜
7
MH50 Cutting edge 50 ㎜ 1.08 ㎜ MS15 Cutting edge 15 ㎜ 0.53 ㎜MH55 Cutting edge 55 ㎜ 1.08 ㎜ MS18 Cutting edge 17.5 ㎜ 0.58 ㎜MH60 Cutting edge 60 ㎜ 1.18 ㎜ MS21 Cutting edge 21 ㎜ 0.68 ㎜MH65 Cutting edge 65 ㎜ 1.18 ㎜ MS24 Cutting edge 24 ㎜ 0.68 ㎜MH70 Cutting edge 70 ㎜ 1.28 ㎜ MS28 Cutting edge 28.5 ㎜ 0.78 ㎜
1/2Circle(180°)
SE-NE-FE-
NH15 Reverse Cutting 15 ㎜ 0.53 ㎜ Reverse edge
2
MS32 Cutting edge 32.5 ㎜ 0.78 ㎜NH18 Reverse Cutting 17.5 ㎜ 0.58 ㎜ Reverse edge MS36 Cutting edge 36.5 ㎜ 0.88 ㎜NH21 Reverse Cutting 21 ㎜ 0.68 ㎜ Reverse edge MS41 Cutting edge 41 ㎜ 0.98 ㎜NH24 Reverse Cutting 24 ㎜ 0.68 ㎜ Reverse edge MS45 Cutting edge 45 ㎜ 1.08 ㎜NH28 Reverse Cutting 28.5 ㎜ 0.78 ㎜ Reverse edge MS50 Cutting edge 50 ㎜ 1.08 ㎜NH32 Reverse Cutting 32.5 ㎜ 0.78 ㎜ Reverse edge MS53 Cutting edge 53 ㎜ 1.08 ㎜NH36 Reverse Cutting 36.5 ㎜ 0.88 ㎜ Reverse edge MS55 Cutting edge 55 ㎜ 1.08 ㎜NH41 Reverse Cutting 41 ㎜ 0.98 ㎜ Reverse edge MS60 Cutting edge 60 ㎜ 1.18 ㎜NH45 Reverse Cutting 45 ㎜ 1.08 ㎜ Reverse edge MS65 Cutting edge 65 ㎜ 1.18 ㎜NH50 Reverse Cutting 50 ㎜ 1.08 ㎜ Reverse edge MS70 Cutting edge 70 ㎜ 1.28 ㎜NH55 Reverse Cutting 55 ㎜ 1.08 ㎜ Reverse edge MS75 Cutting edge 75 ㎜ 1.28 ㎜NH60 Reverse Cutting 60 ㎜ 1.18 ㎜ Reverse edge
5/16Circle(113°)
SE-NE-FE-
ZI07* Trapezoid spatula 7 ㎜ 0.33 ㎜ Except FE Type
8
3/8Circle(135°)
SE-NE-FE-
ME18 Cutting edge 17.5 ㎜ 0.58 ㎜
3
ZI09* Trapezoid spatula 9 ㎜ 0.38 ㎜ Except FE TypeME21 Cutting edge 21 ㎜ 0.68 ㎜ ZI11* Trapezoid spatula 11 ㎜ 0.38 ㎜ Except FE TypeME24 Cutting edge 24 ㎜ 0.68 ㎜ ZI13* Trapezoid spatula 13 ㎜ 0.43 ㎜ Except FE TypeME28 Cutting edge 28.5 ㎜ 0.78 ㎜ MI15 Cutting edge 15 ㎜ 0.48 ㎜ME32 Cutting edge 32.5 ㎜ 0.78 ㎜ MI18 Cutting edge 18 ㎜ 0.53 ㎜ME36 Cutting edge 36.5 ㎜ 0.88 ㎜ MI21 Cutting edge 21 ㎜ 0.58 ㎜ME41 Cutting edge 41 ㎜ 0.98 ㎜
1/2Circle(180°)
SE-NE-FE-
RH22 Trocar 22 ㎜ 0.98 ㎜
14
ME45 Cutting edge 45 ㎜ 1.08 ㎜ RH25 Trocar 25 ㎜ 0.98 ㎜ME50 Cutting edge 50 ㎜ 1.08 ㎜ RH29 Trocar 29 ㎜ 1.08 ㎜ME55 Cutting edge 55 ㎜ 1.08 ㎜ RH35 Trocar 35 ㎜ 1.18 ㎜ME60 Cutting edge 60 ㎜ 1.18 ㎜ RH40 Trocar 40 ㎜ 1.28 ㎜ME65 Cutting edge 65 ㎜ 1.18 ㎜ RH46 Trocar 46 ㎜ 1.28 ㎜ME70 Cutting edge 70 ㎜ 1.28 ㎜ RH55 Trocar 55 ㎜ 1.38 ㎜
7/16Circle(158°)
SE-NE-FE-
MG26L Cutting edge 26 ㎜ 0.88 ㎜ Thick
4
RH60 Trocar 60 ㎜ 1.38 ㎜MG31L Cutting edge 31 ㎜ 0.98 ㎜ Thick RH63 Trocar 63 ㎜ 1.38 ㎜MG36L Cutting edge 36 ㎜ 0.98 ㎜ Thick RH88 Trocar 88 ㎜ 1.58 ㎜MG41L Cutting edge 41 ㎜ 1.08 ㎜ ThickMG45L Cutting edge 45 ㎜ 1.08 ㎜ ThickMG51L Cutting edge 51 ㎜ 1.18 ㎜ ThickMG56L Cutting edge 56 ㎜ 1.28 ㎜ ThickMG61L Cutting edge 61 ㎜ 1.28 ㎜ ThickMG66L Cutting edge 66 ㎜ 1.38 ㎜ ThickMG71L Cutting edge 71 ㎜ 1.38 ㎜ ThickMG76L Cutting edge 76 ㎜ 1.48 ㎜ Thick
1/2Circle (180°)
SE-NE-FE-
MH28LL Cutting edge 28 ㎜ 0.98 ㎜ Extra thick
5
MH32LL Cutting edge 32 ㎜ 0.98 ㎜ Extra thickMH36LL Cutting edge 36 ㎜ 1.18 ㎜ Extra thickMH40LL Cutting edge 40 ㎜ 1.28 ㎜ Extra thickMH45LL Cutting edge 45 ㎜ 1.28 ㎜ Extra thickMH50LL Cutting edge 50 ㎜ 1.28 ㎜ Extra thickMH55LL Cutting edge 55 ㎜ 1.28 ㎜ Extra thickMH60LL Cutting edge 60 ㎜ 1.38 ㎜ Extra thickMH65LL Cutting edge 65 ㎜ 1.38 ㎜ Extra thick
4
CurvatureOrder Code Specification
Note Ref. CurvatureOrder Code Specification
Note Ref.Eye Type Shape Length Diameter Eye
Type Shape Length Diameter
1/2Circle(180°)
SE-NE-FE-
TH13 Taper point 13 ㎜ 0.53 ㎜
9
3/8Circle(135°)
SE-NE-FE-
TE18F Taper point 18 ㎜ 0.53 ㎜ Fine
15
TH15 Taper point 15 ㎜ 0.53 ㎜ TE24F Taper point 23.5 ㎜ 0.58 ㎜ FineTH18 Taper point 17.5 ㎜ 0.58 ㎜ TE29F Taper point 29 ㎜ 0.63 ㎜ FineTH21 Taper point 21 ㎜ 0.68 ㎜ TE34F Taper point 34 ㎜ 0.73 ㎜ FineTH24 Taper point 24 ㎜ 0.68 ㎜ TE40F Taper point 40 ㎜ 0.78 ㎜ FineTH28 Taper point 28.5 ㎜ 0.78 ㎜ TE45F Taper point 45 ㎜ 0.78 ㎜ FineTH32 Taper point 32.5 ㎜ 0.78 ㎜ TE50F Taper point 50 ㎜ 0.88 ㎜ FineTH36 Taper point 36.5 ㎜ 0.88 ㎜ TE55F Taper point 55 ㎜ 0.88 ㎜ Fine
TH41 Taper point 41 ㎜ 0.98 ㎜ 1/2Circle(180°)
SE-NE-FE-
BH41 Blunt point 41 ㎜ 1.08 ㎜
16TH45 Taper point 45 ㎜ 1.08 ㎜ BH51 Blunt point 51 ㎜ 1.18 ㎜TH50 Taper point 50 ㎜ 1.08 ㎜ BH66 Blunt point 66 ㎜ 1.38 ㎜
TH55 Taper point 55 ㎜ 1.08 ㎜
5/16Circle(113°)
SE-NE-FE-
TI07* Taper point 7 ㎜ 0.33 ㎜ Except FE Type
17
TH60 Taper point 60 ㎜ 1.18 ㎜ TI09* Taper point 9 ㎜ 0.38 ㎜ Except FE TypeTH65 Taper point 65 ㎜ 1.18 ㎜ TI11* Taper point 11 ㎜ 0.38 ㎜ Except FE TypeTH70 Taper point 70 ㎜ 1.28 ㎜ TI13* Taper point 13 ㎜ 0.43 ㎜ Except FE Type
1/2Circle(180°)
SE-NE-FE-
TH13F Taper point 13 ㎜ 0.48 ㎜ Fine
10
TI15 Taper point 15 ㎜ 0.48 ㎜TH18F Taper point 18 ㎜ 0.53 ㎜ Fine TI18 Taper point 18 ㎜ 0.53 ㎜TH21F Taper point 21 ㎜ 0.58 ㎜ Fine TI21 Taper point 21 ㎜ 0.58 ㎜
TH24F Taper point 23.5 ㎜ 0.58 ㎜ Fine
5/8Circle(225°)
SE-NE-FE-
TF28LL Taper point 28 ㎜ 0.98 ㎜ Extra thick
18
TH29F Taper point 29 ㎜ 0.63 ㎜ Fine TF32LL Taper point 32 ㎜ 0.98 ㎜ Extra thickTH32F Taper point 32 ㎜ 0.63 ㎜ Fine TF36LL Taper point 36 ㎜ 1.18 ㎜ Extra thickTH34F Taper point 34 ㎜ 0.73 ㎜ Fine TF40LL Taper point 40 ㎜ 1.28 ㎜ Extra thickTH36F Taper point 36 ㎜ 0.73 ㎜ Fine TF45LL Taper point 45 ㎜ 1.28 ㎜ Extra thickTH40F Taper point 40 ㎜ 0.78 ㎜ Fine TF50LL Taper point 50 ㎜ 1.28 ㎜ Extra thickTH45F Taper point 45 ㎜ 0.78 ㎜ Fine TF55LL Taper point 55 ㎜ 1.28 ㎜ Extra thickTH50F Taper point 50 ㎜ 0.88 ㎜ Fine TF60LL Taper point 60 ㎜ 1.38 ㎜ Extra thickTH55F Taper point 55 ㎜ 0.88 ㎜ Fine TF65LL Taper point 65 ㎜ 1.38 ㎜ Extra thickTH60F Taper point 60 ㎜ 0.88 ㎜ Fine
StraightSE-NE-FE-
TS13 Taper point 13 ㎜ 0.53 ㎜
19
3/8Circle(135°)
SE-NE-FE-
TE18 Taper point 17.5 ㎜ 0.58 ㎜
11
TS15 Taper point 15 ㎜ 0.53 ㎜TE21 Taper point 21 ㎜ 0.68 ㎜ TS18 Taper point 17.5 ㎜ 0.58 ㎜TE24 Taper point 24 ㎜ 0.68 ㎜ TS21 Taper point 21 ㎜ 0.68 ㎜TE28 Taper point 28.5 ㎜ 0.78 ㎜ TS24 Taper point 24 ㎜ 0.68 ㎜TE32 Taper point 32.5 ㎜ 0.78 ㎜ TS28 Taper point 28.5 ㎜ 0.78 ㎜TE36 Taper point 36.5 ㎜ 0.88 ㎜ TS32 Taper point 32.5 ㎜ 0.78 ㎜TE41 Taper point 41 ㎜ 0.98 ㎜ TS36 Taper point 36.5 ㎜ 0.88 ㎜TE45 Taper point 45 ㎜ 1.08 ㎜ TS41 Taper point 41 ㎜ 0.98 ㎜TE50 Taper point 50 ㎜ 1.08 ㎜ TS45 Taper point 45 ㎜ 1.08 ㎜TE55 Taper point 55 ㎜ 1.08 ㎜ TS50 Taper point 50 ㎜ 1.08 ㎜TE60 Taper point 60 ㎜ 1.18 ㎜ TS53 Taper point 53 ㎜ 1.08 ㎜TE65 Taper point 65 ㎜ 1.18 ㎜ TS55 Taper point 55 ㎜ 1.08 ㎜TE70 Taper point 70 ㎜ 1.28 ㎜ TS60 Taper point 60 ㎜ 1.18 ㎜
7/16Circle(158°)
SE-NE-FE-
TG26L Taper point 26 ㎜ 0.88 ㎜ Thick
12
TS65 Taper point 65 ㎜ 1.18 ㎜TG31L Taper point 31 ㎜ 0.98 ㎜ Thick TS70 Taper point 70 ㎜ 1.28 ㎜TG36L Taper point 36 ㎜ 0.98 ㎜ Thick TS75 Taper point 75 ㎜ 1.28 ㎜
TG41L Taper point 41 ㎜ 1.08 ㎜ Thick
StraightSE-NE-FE-
TS13F Taper point 13 ㎜ 0.48 ㎜ Fine
20
TG45L Taper point 45 ㎜ 1.08 ㎜ Thick TS15F Taper point 15 ㎜ 0.48 ㎜ FineTG51L Taper point 51 ㎜ 1.18 ㎜ Thick TS18F Taper point 18 ㎜ 0.53 ㎜ FineTG56L Taper point 56 ㎜ 1.28 ㎜ Thick TS21F Taper point 21 ㎜ 0.58 ㎜ FineTG61L Taper point 61 ㎜ 1.28 ㎜ Thick TS24F Taper point 23.5 ㎜ 0.58 ㎜ FineTG66L Taper point 66 ㎜ 1.38 ㎜ Thick TS29F Taper point 29 ㎜ 0.63 ㎜ FineTG71L Taper point 71 ㎜ 1.38 ㎜ Thick TS32F Taper point 32 ㎜ 0.63 ㎜ FineTG76L Taper point 76 ㎜ 1.48 ㎜ Thick TS34F Taper point 34 ㎜ 0.73 ㎜ Fine
1/2Circle(180°)
SE-NE-FE-
TH28LL Taper point 28 ㎜ 0.98 ㎜ Extra thick
13
TS36F Taper point 36 ㎜ 0.73 ㎜ FineTH32LL Taper point 32 ㎜ 0.98 ㎜ Extra thick TS38F Taper point 38 ㎜ 0.78 ㎜ FineTH36LL Taper point 36 ㎜ 1.18 ㎜ Extra thick TS40F Taper point 40 ㎜ 0.78 ㎜ FineTH40LL Taper point 40 ㎜ 1.28 ㎜ Extra thick TS43F Taper point 43 ㎜ 0.78 ㎜ FineTH45LL Taper point 45 ㎜ 1.28 ㎜ Extra thick TS45F Taper point 45 ㎜ 0.78 ㎜ FineTH50LL Taper point 50 ㎜ 1.28 ㎜ Extra thick TS48F Taper point 48 ㎜ 0.88 ㎜ FineTH55LL Taper point 55 ㎜ 1.28 ㎜ Extra thick TS50F Taper point 50 ㎜ 0.88 ㎜ FineTH60LL Taper point 60 ㎜ 1.38 ㎜ Extra thick TS55F Taper point 55 ㎜ 0.88 ㎜ FineTH65LL Taper point 65 ㎜ 1.38 ㎜ Extra thick TS60F Taper point 60 ㎜ 0.88 ㎜ Fine
TS65F Taper point 65 ㎜ 0.88 ㎜ FineTS70F Taper point 70 ㎜ 0.88 ㎜ Fine
㎜ ㎜ ㎜ ㎜
㎜ ㎜
131517.521
24
28.5
32.5
36.5
41
45
50
55
60
65
70
φ0.530.530.580.680.68
0.780.78
0.88
0.98
1.08
1.08
1.08
1.18
1.18
1.28
17.5
21
24
28.5
32.5
36.5
41
45
50
55
60
65
70
182124
28
32
36
41
45
50
55
60
65
70
φ0.58
0.680.68
0.78
0.78
0.88
0.98
1.08
1.08
1.08
1.18
1.18
1.28
15
17.5
21
24
28.5
32.5
36.5
41
45
50
55
60
φ0.530.58
0.68
0.68
0.78
0.78
0.88
0.98
1.08
1.08
1.08
1.18
1315182124
2832
36
41
45
50
55
60
65
70
㎜ ㎜
15
18
21
24
28
32
36
41
45
50
55
60
26
31
36
41
45
51
56
61
66
71
76
26
31
36
41
45
51
56
61
66
71
76
φ0.88
0.98
0.98
1.08
1.08
1.18
1.28
1.28
1.38
1.38
1.48
マニーアイド縫合針
Cutting edge 1/2 circle (H) Reverse Cutting 1/2 circle (H)
Cutting edge 7/16 circle (G)Cutting edge 3/8 circle (E)
1
3
2
4
5
Cutting edge 1/2 circle (H) Taper point 1/2 circle (H)
Cutting edge Straight[S] Taper point Straight[S]
SE-MS_or
NE-MS_or
FE-MS_
13
15
17.5
21
24
28.5
32.5
36.5
41
45
50
53
55
60
65
70
75
13
15
18
21
24
28
32
36
41
45
50
53
55
60
65
70
75
φ0.53
0.53
0.58
0.68
0.68
0.78
0.78
0.88
0.98
1.08
1.08
1.08
1.08
1.18
1.18
1.28
1.28
28
32
36
40
45
50
55
60
65
28
32
36
40
45
50
55
60
65
φ0.98
0.98
1.18
1.28
1.28
1.28
1.28
1.38
1.38
SE-MH_LLor
NE-MH_LLor
FE-MH_LL
SE-MF_LLor
NE-MF_LLor
FE-MF_LL
28
32
36
40
45
50
55
60
65
28
32
36
40
45
50
55
60
65
φ0.98
0.98
1.18
1.28
1.28
1.28
1.28
1.38
1.38
SE-MI_or
NE-MI_or
FE-MI_
SE-ZI_or
NE-ZI_
7
9
11
13
15
18
21
07
09
11
13
15
18
21
φ0.33
0.38
0.38
0.43
0.48
0.53
0.58
マニーアイド縫合針MANI SURGICAL EYED NEEDLES
Order Length(㎜) Diameter(㎜)code
Order Length(㎜) Diameter(㎜)code
Order Length(㎜) Diameter(㎜)code
Order Length(㎜) Diameter(㎜)code
Cutting edge 1/2 circle (H) Cutting edge 5/8 circle (F)
Trapezoid spatula/Cutting edge 5/16 circle (I)
Cutting edge Straight (S)
6
5
7
6
8
13
1517.521
24
28.5
32.5
36.5
41
45
50
55
60
65
70
131518212428
32
36
41
45
50
55
60
65
70
φ0.530.530.580.680.680.78
0.78
0.88
0.98
1.08
1.08
1.08
1.18
1.18
1.28
SE-TH_or
NE-TH_or
FE-TH_
SE-TE_or
NE-TE_or
FE-TE_
17.5
21
24
28.5
32.5
36.5
41
45
50
55
60
65
70
1821
24
28
32
36
41
45
50
55
60
65
70
φ0.580.68
0.68
0.78
0.78
0.88
0.98
1.08
1.08
1.08
1.18
1.18
1.28
13
18
21
24
29
32
34
36
40
45
50
55
φ0.48
0.53
0.58
0.58
0.63
0.63
0.73
0.73
0.78
0.78
0.88
0.88
13
18
21
23.5
29
32
34
36
40
45
50
55
SE-TH_For
NE-TH_For
FE-TH_F
SE-TG_Lor
NE-TG_Lor
FE-TG_L
26
31
36
41
45
51
56
61
66
71
76
26
31
36
41
45
51
56
61
66
71
76
φ0.88
0.98
0.98
1.08
1.08
1.18
1.28
1.28
1.38
1.38
1.48
マニーアイド縫合針MANI SURGICAL EYED NEEDLES
Order Length(㎜) Diameter(㎜)code
Order Length(㎜) Diameter(㎜)code
Order Length(㎜) Diameter(㎜)code
Order Length(㎜) Diameter(㎜)code
7
Taper point 1/2 circle (H) Taper point 1/2 circle (H)
Taper point 7/16 circle (G)Taper point 3/8 circle (E)
9
11
10
12
22
25
29
35
40
46
55
60
63
88
2225
29
35
40
46
55
60
63
88
φ0.980.98
1.08
1.18
1.28
1.28
1.38
1.38
1.38
1.58
SE-RH_or
NE-RH_or
FE-RH_
28
32
36
40
45
50
55
60
65
28
32
36
40
45
50
55
60
65
φ0.98
0.98
1.18
1.28
1.28
1.28
1.28
1.38
1.38
SE-TH_LLor
NE-TH_LLor
FE-TH_LL
18
23.5
29
34
40
45
50
55
18
24
29
34
40
45
50
55
φ0.53
0.58
0.63
0.73
0.78
0.78
0.88
0.88
SE-TE_For
NE-TE_For
FE-TE_F
41
51
66
φ1.08
1.18
1.38
41
51
66
SE-BH_or
NE-BH_or
FE-BH_
マニーアイド縫合針MANI SURGICAL EYED NEEDLES
Order Length(㎜) Diameter(㎜)code
Order Length(㎜) Diameter(㎜)code
Order Length(㎜) Diameter(㎜)code
Order Length(㎜) Diameter(㎜)code
8
Taper point 1/2 circle (H) Trocar 1/2 circle (H)
Blunt point 1/2 circle (H)
Taper point 3/8 circle (E)
13
15
14
16
SE-TI_or
NE-TI_or
FE-TI_(Except*)
7
9
11
13
15
18
21
07*
09*
11*
13*
15
18
21
φ0.33
0.38
0.38
0.43
0.48
0.53
0.58
SE-TF_LLor
NE-TF_LLor
FE-TF_LL
28
32
36
40
45
50
55
60
28
32
36
40
45
50
55
60
φ0.98
0.98
1.18
1.28
1.28
1.28
1.28
1.38
13
15
17.5
21
24
28.5
32.5
36.5
41
45
50
53
55
60
65
70
75
13
15
18
21
24
28
32
36
41
45
50
53
55
60
65
70
75
φ0.53
0.53
0.58
0.68
0.68
0.78
0.78
0.88
0.98
1.08
1.08
1.08
1.08
1.18
1.18
1.28
1.28
SE-TS_or
NE-TS_or
FE-TS_
Codes listed in this catalogue are our standard products. Please feel free to contact us if you are looking for specifica-tions not listed in this catalogue or custom-made needles.
13
15
18
21
23.5
29
32
34
36
38
40
43
45
48
50
55
13
15
18
21
24
29
32
34
36
38
40
43
45
48
50
55
φ0.48
0.48
0.53
0.58
0.58
0.63
0.63
0.73
0.73
0.78
0.78
0.78
0.78
0.88
0.88
0.88
SE-TS_For
NE-TS_For
FE-TS_F
マニーアイド縫合針MANI SURGICAL EYED NEEDLES
Order Length(㎜) Diameter(㎜)code
Order Length(㎜) Diameter(㎜)code
Order Length(㎜) Diameter(㎜)code
Order Length(㎜) Diameter(㎜)code
Taper point 5/8 circle (F) Taper point 5/16 circle (I)
Taper point Straight (S)
Taper point Straight (S)
9
17
19
18
20
Laos
Myanmar
Vietnam
MANI HANOI CO.,LTD.MANI HANOI CO.,LTD.
MANI YANGON LTD.
MANI VIENTIANE SOLE. CO., LTD.
JapanMANI,INC. Kiyohara FactoryMANI,INC. Takanezawa Factory
10
デザイン・仕様は改良のため予告なしに変更することがあります。 S01220
〒321-3231 栃木県宇都宮市清原工業団地8-3 Tel: 028-667-1811(代)【サージカル営業】Tel:028-667-8345/Fax:028-667-8305
8-3 KIYOHARA INDUSTRIAL PARK, UTSUNOMIYA, TOCHIGI 321-3231 JAPAN Surgical Exp. Sec./Phone:+81-28-667-8346 Fax:+81-28-667-8305URL:http://www.mani.co.jp/en/index.html E-mail:[email protected]
製造販売元
Legal Manufacturer