324-31283 allweiller pmup

7/23/2019 324-31283 Allweiller Pmup

1/20

VM 528 GB/12.05 Ident No. 795 261 1

Volute Casing Centrifugal Pumpsof Block Design

Series NB

Application

For pumping pure water, industrial water, sea water, con-densates, oils, brines, lyes and hot water.

The fluids to be pumped must not contain any abrassive parti-cles nor chemically attack the pump materials.

Main fields of application

In cooling and heating systems, in circulating, water supply,

water treatment, sea-water desalination, dedusting andspray painting plants as well as in air-conditioning, cooling,swimming pool and industrial engineering.

Design and series construction

Volute casing centrifugal pump, single entry, single or two-stage, of block design. Pump size according to DIN EN 733.

Stub and motor shaft are rigidly coupled together. Shaft bear-ing in the motor by means of grease-lubricated groove ballbearings. The mating dimensions of the two-stage sizes2/25200/01, 2/32200/01, 2/40250/01, 2/50250/01, exceptfor dimensions f and l depending upon the driving motors, cor-respond to the single-stage designs. Volute casing with feetcast on.

Horizontal or vertical installation, motor arrangement down-wards is not admissible.

Performance data

Delivery Q up to 480 m3/hDelivery head H up to 145 mTemperature of the fluid pumped t up to 140 CInlet pressure ps Pump outlet pressure as afunction of the shaft diameterand the shaft seal

with diameter 16, 24, 30 pd up to 16 bar with diameter 40 pd up to 10 bar

Drive power P 0,25 up to 37 kWNominal diameter, delivery flange DNd 25 up to 150

Branch position/flanges

Suction branch: axialDelivery branch: radially upwardsFlanges: up to DN 150 acc. to EN 1092-2 PN 16

as from DN 200 acc. to EN 1092-2 PN 10

Contact protection

The requirements of DIN EN 809 Contact protection, aremet.

Shaft seal

By maintenance-free mechanical seal in unbalanced design(main dimensions acc. to DlN EN 12 756, design K, shape U).

Combination of components

The table on page 3 shows the combination possibilities ofcomponents of all NB sizes. The unit assembly system allowsreduced stockkeeping of spare parts.

Explosion protection

The pump fulfils the requirements according to ECExplosion Protection Directive 94/9EG (ATEX 100a)for equipment and equipment group II, category 2 G.

Categorisation into temperature classes according to EN13463-1 depends on the temperature of the pumped medium.The max. permissible temperature of the pumped medium forthe respective temperature classes are shown in the specific

order data sheet.Note:In case of the operation of a category 2 pump, the un-acceptable heating of the pump surfaces caused by a possibleoperational fault must be prevented by a control mechanism.In case of an operation with constant parameters (pressure,temperature, speed

= const.), a pump performance controllercan be supplied with the pump to detect any operational faults.

Drive

Surface-cooled three-phase squirrel-cage induction motors,with locating-type bearing, IM V1 type of construction, en-closure IP55 according to IEC Standard, class F insulation,performances and main dimensions according to DIN 42 677,up to 2.2 kW 230/400V, from 3 kW 400/690 V.

Attention: Motors provided by customers must also have a

locating-type bearing!

Dismantling the driving unit

When dismantling the driving unit, the volute casing may re-main in the piping.

Connections

The following auxiliary connections are always provided:FD DrainingFF FillingFV VentingPM2 Pressure measurement pump

inlet pressure plus maximum delivery head must not exceed the admissiblepump outlet pressure

allocation pump size / shaft diameter at the shaft seal, refer to pages10 to 17

in case the temperature of fluids pumped exceeds 120C, the admis-sible pump outlet pressure changes as follows:

connection FF at sizes 20-160/01; 25-200/01 und 2/25-200/01 notexistent; failure at connection PM2 possible


2/20

Series NB

VM 528 GB/12.05 Ident No. 795 2612

Shaft seals with temperature and pressure limits

Available for al l material designs

Mechanical seal, uncooled Unbalanced

Flushing Internal flushing Internal flushing bores

Abbreviation U3D U3.1D U 3.9D U3.12D U3.20D U3.10K U3.11K

Rotating seal ringHard carbon,

synthetic resin impregnatedSilicon carbide

Hard carbon,antimony impregnated

Hard carbon,synthetic resin impregnated

Stationary seal ring Oxide ceramics Silicon carbide Silicon carbide

Metal parts CrNiMo steel CrNiMo steel CrNiMo steel

O-rings EPDM FPM EPDM FPM EPDM EPDM Viton

Bellows - - EPDM FPM - - -

Material key,DIN EN 12 756

BVEGG BVVGG Q1Q1EGG Q1Q1VGG AQ1EGG BQ1EGG BQ1VGG

Volute casing centrifugal pumpsat bearing bracket size

Admissible temperature of the fluid pumped (C) and admissible pump outlet pressure pd(bar)

C / bar C / bar C / bar C / bar C / bar C / bar C / bar

single-stage100 / 10

-100 / 10

-100 / 10

-100 / 10

-140 / 10

120 / 16140 / 12

120 / 16 140 / 12

two-stage 100 / 16 100 / 16 100 / 10 100 / 10 140 / 16 - -

applies to water max. 90 C

only possible for sizes with shaft diameters 16, 24, 30 (at the shaft seal)in case of inlet pressure > 5 bar, shaft seal U3.20 D or U3.10 K must be provided

Other mechanical seal designs on inquiery.

Abbreviation system

NB 40 - 200 / 01 / 180 U3D - W3 - 38 / 300

Series

Size

Hydraulic no.

Actual impeller diameter

Shaft seal

Material design

Stub shaft bore diameter for fixing to motor shaft end

Drive lantern or intermediate ring outside diameter or flange size of electric motor

The actual impeller diameter of two-stage sizes relates to the second stage. The number of stages is placed in front of the nominal width of the outlet branch,e.g. 2/40200/...

Materials

Part No. Material designsDenomination

single-stage two-stage W 3 W 18 W 19 W 88 W 97

Volute casing 102... 102... G-CuAl 10 Ni EN-GJL-250 EN-GJL-250 EN-GJS-400-15 EN-GJS-400-15

Impeller 230... - G-CuAl 10 Ni G-CuAl 10 Ni EN-GJL-200 G-CuAl 10 Ni EN-GJL-200

Impeller 1st stage - 230... G-CuAl 10 Ni G-CuAl 10 Ni EN-GJL-200 G-CuAl 10 Ni EN-GJL-200

Impeller 2nd stage - 230... G-CuAl 10 Ni G-CuAl 10 Ni EN-GJL-200 G-CuAl 10 Ni EN-GJL-200

Diffuser - 171... G-CuAl 10 Ni G-CuAl 10 Ni EN-GJL-200 G-CuAl 10 Ni EN-GJL-200

Stage casing - 108... G-CuAl 10 Ni EN-GJL-250 EN-GJL-250 EN-GJS-400-15 EN-GJS-400-15

Casing cover 161... 161... G-CuAl 10 Ni EN-GJL-250 EN-GJL-250 EN-GJS-400-15 EN-GJS-400-15

Stub shaft 220... 220... 1.4571/1.7139 1.4571/1.7139 1.4571/1.7139 1.4571/1.7139 1.4571/1.7139

Drive lantern 341... 341... EN-GJL-250 EN-GJL-250 EN-GJL-250 EN-GJL-250 EN-GJL-250

Intermediate ring 509.01 - G-CuAl 10 Ni EN-GJL-250 EN-GJL-250 EN-GJS-400-15 EN-GJS-400-15

Intermediate ring 509.02 - EN-GJL-250 or St EN-GJL-250 or St EN-GJL-250 or St EN-GJL-250 oder St EN-GJL-250 oder St

in contact with fluids 1.4571/ motor side 1.7139

Standard nominal width on delivery sideNominal impeller diameter


3/20

Series NB

VM 528 GB/12.05 Ident No. 795 261 3

Combination of components

The following table shows the combination possibilities of components or spare parts of the NI sizes.Within a vertical column, parts with identical numbers are interchangeable.

ImpellerShaftdiameter at

the shaft seal

Stub shaft Drivelantern

Intermediatering

mm

Pump sizeNI

Volutecasing

Impeller

1ststage

2ndstage

Diffuser Stagecasing

Inter-mediate

ring

Casingcover

The allocation to the sizesdepends on speed, motor

performance and motor design.

20-160/01 1 1

16

25-160/01 2 1

- - - - - 1

16-14

16-19

16-24

16-28

16-160

16-200

16-250

-

32-125/01 3 2

40-125/01 4 3

50-125/01 5 424

65-125/01 6 5

- - - - - 2

24-14

24-19

24-24

24-28

24-38

24-42

24-160

24-200

24-250

24-300

24-350

-

25-200/01 7 6

32-160/01 8 7

32-200/01 9 8

40-160/01 10 9

40-200/01 11 10

-

40-250/01 12 11 1

50-160/01 13 12

50-200/01 14 13-

50-250/01 15 14 1

65-160/01 16 15 -

65-200/02 17 16 1

80-160/01 18 17

30

100-160/01 19 18

- - - -

-

3

30-19

30-24

30-28

30-38

30-42

30-48

30-55

30-200

30-250

30-300

30-350

30-400

-

2/25-200/01 7 -

2/32-200/01 9 -

1 1 1 1 4

2/40-250/01 12 - 2

30

zweistufig

2/50-250/01 15 - 3

2 2 2

-

5

2/30-19

2/30-24

2/30-28

2/30-38

2/30-42

2/30-48

2/30-55

30-200

30-250

30-300

30-350

30-400

-

65-250/01 20 19 -

65-315/01 21 20 2

65-400/01 22 21 3

80-200/02 23 22

80-250/01 24 23-

80-315/01 25 24 2

100-200/01 26 25

100-250/01 27 26-

100-315/01 28 27 2

125-200/01 29 28

125-250/01 30 29

40

150-200/01 31 30

- - - -

-

6

40-28

40-38

40-42

40-48

40-55

40-360

280.180.0

280.230.20

280.250.50

280.300.50


4/20

Series NB

VM 528 GB/12.05 Ident No. 795 2614

Optimized hydraulic with verygood efficiencies and NPSH-valuesof the standard seriesNT acc. to DIN EN 733, deliv-ery rate partly considerableabove the standard de-mands

When dismantling the drivingunit (including impeller) thevolute casing remains in thepiping.

Negligible axial thrustby fineadaption of the balancing holes.

Uncooled, unbalanced mechanicalsealfor cavities according toDIN EN 12 756, design K, form U.

Commercial standard motorswith locating-type bearing, con-struction IM V1, all types of en-closures and speeds of rotationpossible.

Horizontal and vertical mount-ing possiblewith exception ofmotor downward.

Larger delivery headswithtwo-stage sizes (2/25-200/01,2/32-200/01, 2/40-250/01,2/50-250/01).The outer dimensions corre-spond with the single stagedesign.


5/20

Series NB

VM 528 GB/12.05 Ident No. 795 261 5

Performance graphs

n = 1450 1/min

n = 2900 1/min

For exact performance data, please refer to the individual characteristics.

Valid for = 1 kg/dm and = 1 mm/s


6/20

Series NB

VM 528 GB/12.05 Ident No. 795 2616

n = 1750 1/min

n = 3500 1/min

For exact performance data, please refer to the individual characteristics.

Valid for = 1 kg/dm and = 1 mm/s


7/20

Series NB

VM 528 GB/12.05 Ident No. 795 261 7

Sectional drawing

Single-stage sizes with shaft diameter 16at the shaft seal

Fixing of guard plate to the drive lantern.Protection against accidental contact acc. to DIN EN 809

Denomination Part No. Denomination Part No. Denomination Part No.

Volute casing 102.01 Washer 554.07 Socket head cap screw 914.06

Casing cover 161.05 Rivet 565.01 Impeller nut 922.01

Stub shaft 220.01 Bleeder screw 672.01 Spring washer 936.01

Impeller 230.01 Guard plate 686.01 Key 940.01

Drive lantern 341.01 Flange-mounted motor 801.01 Rating plate 971.01

Gasket 400.01 Hexagonal screw 901.01

Joint ring 411.02 Hexagonal screw 901.02

Joint ring 411.04 Hexagonal screw 901.07 Connections

Joint ring 411.05 Hexagonal screw 901.10 FD Drainage

Mechanical seal 433.01 Screwed plug 903.02 FV Venting

Spacer sleeve 525.01 Screwed plug 903.04 PM2 Pressure measurement


8/20

Series NB

VM 528 GB/12.05 Ident No. 795 2618

Sectional drawing

Single-stage sizes with shaft diameters 24 and 30at the shaft seal

Shaft seal: uncooled, unbalanced mechanical seal

Abbreviation: U 3 D

Casing cover design atsizes 2/40-250/01 and 2/50-250/01


Sizes with shaft seal diameter 24 at the shaft seal

Design with intermediate ring,sizes 40-250/01 and 50-250/01

Two-stage sizes with shaft diameter 30 at theshaft seal, uncooled, unbalanced mechanical sealsU 3 D and U 3.20 D


9/20

Series NB

VM 528 GB/12.05 Ident No. 795 261 9

Sectional drawing

Sizes with shaft diameter 40at the shaft seal

Shaft seal: uncooled, unbalanced mechanical sealAbbreviation: U 3 D

Design with intermediate ring,sizes 65-315/01, 80-315/01, 100-315/01, 65-400/01


Denomination Part No. Denomination Part No. Denomination Part No.

Volute casing 102.01 Intermediate ring 509.01 Socket head cap screw 914.01Stage casing 108.01 Intermediate ring 509.02 Socket head cap screw 914.02

Casing cover 161.05 Threaded ring 514.01 Socket head cap screw 914.06

Casing cover 161.10 Spacer sleeve 525.01 Socket head cap screw 914.10

Casing cover 161.12 Spacer sleeve 525.02 Hexagonal nut 920.01

Diffuser 171.01 Washer 554.07 Hexagonal nut 920.03

Stub shaft 220.01 Rivet 565.01 Impeller nut 922.01

Stub shaft 220.02 Bleeder screw 672.01 Spring washer 936.01

Impeller 230.01 Guard plate 686.01 Key 940.01

Impeller 1ststage 230.02 Flange-mounted motor 801.01 Key 940.03

Impeller 2ndstage 230.03 Hexagonal screw 901.01 Rating plate 971.01

Drive lantern 341.01 Hexagonal screw 901.02



Joint ring 411.01 Stud bolt 902.01

Joint ring411.02

Stud bolt 902.08 ConnectionsJoint ring 411.04 Screwed plug 903.01 FD Drainage

Joint ring 411.05 Screwed plug 903.02 FF Filling

O-ring 412.01 Screwed plug 903.04 FV Venting

Mechanical seal 433.01 Grub screw 904.05 PM2 Pressure measurement


10/20

Series NB

VM 528 GB/12.05 Ident No. 795 26110

n = 1450/1750 min-

Aggregate dimensions: Sizes with shaft diameters 16, 24 and 30at the shaft seal

Shaftdiameter

at the shaftseal

Connections

Drain-ing

Fill-ing

Vent-ing

Pressuremeasurement

mm FD FF FV PM2

16 G 1/4 G 1/4 G 1/8 G 1/4

24, 30 G 1/4

G 1/4

G 1/4 G 1/4

Connections at sizes 25-200 and 2/25-200: FD = G 1/2;FF at sizes 20-160, 25-200 and 2/25-200 not existent.

Flanges acc. to EN 1092-2 PN 16

DNdDNs

D bf k gNo. ofholes

25 115 16 85 14 432 140 18 100 19 4

40 150 18 110 19 4

50 165 20 125 19 4

65 185 20 145 19 4

80 200 22 160 19 8

Tolerances of companion dimensions Sense of rotation: clockwise as seen Dimensions in mmacc. to DIN EN 735 from the driving side without commitment

Aggregate dimensions

Pump dimensions

Shaftdiameter atshaft seal

Pumpsize

Motorsize

Perfor-mance

Flanges Feet

Motor dimensionsapprox. dimensionsvarying dependingupon manufacturer

Extensiondim.

mm kW DNs DNd a f a2 b1 b2 f1 h1 h2 b c m1 m2 n1 n2 s a1 d h3 l1 l x

Allocationstub shaft/

motor bracket/intermediate

ring

Contained inabbreviation,

v. page 2

71 0,25 0,37 118 160 145 116 237 418 14/16020-160/01

80 0,55 0,7525 25 63

138- 108 108 - 112 145 50 14 100 70 220 180 M10

200 162 124 234 43562

19/200

71 0,25 0,37 118 160 145 116 237 418 14/16016

25-160/0180 0,55 0,75

25 25 63138

- 100 108 - 112 160 50 12 100 70 220 180 M10200 162 124 234 435

6219/200

71 0,25 0,37 160 145 116 237 465 14/160

80 0,55 0,75 162 124 234 462 19/20032-125/01

90 S 1,1

50 32 80 148 - 96 96 - 112 140 50 15 100 70 190 140 M12200

181 130 282 510

89

24/20071 0,25 0,37 160 145 116 237 465 14/160

80 0,55 0,75 162 124 234 462 19/20040-125/01

90 S 1,1

65 40 80 148 - 96 110 - 112 140 50 15 100 70 210 160 M12200

181 130 282 510

89

24/200

71 0,25 0,37 160 145 116 237 485 14/160

80 0,55 0,75 162 124 234 482 19/200

90 S 1,1 181 130 282 530 24/200

90 L 1,5

200

181 130 282 530 24/200

50-125/01

100 L 2,2 3

65 5 0 100 148 - 1 10 130 - 1 32 160 50 15 100 70 240 190 M12

250 203 158 312 560

89

28/250

71 0,25 0,37 160 145 116 237 485 14/160

80 0,55 0,75 162 124 234 482 19/200

90 S 1,1 181 130 282 530 24/200

90 L 1,5

200

181 130 282 530 24/200

24

65-125/01

100 L 2,2 3

80 6 5 100 148 - 1 20 148 - 1 60 180 65 15 125 95 280 212 M12

250 203 158 312 560

95

28/250

80 0,55 0,75 162 124 234 463 19/200

90 S 1,1 181 130 282 511 24/20025-200/0190 L 1,5

40 2 5 80 149 - 132 132 - 1 60 180 50 15 100 70 240 190 M12 200181 130 282 511

10224/200

80 0,55 0,75 162 124 234 497 19/200

90 S 1,1 181 130 282 545 24/200

90 L 1,5

183 200

181 130 282 545 24/200

30

2/25-200/01

100 L 2,2 3

40 25 80

193

- 132 132 - 160 180 50 15 100 70 240 190 M12

250 203 158 312 585

102

28/250


11/20

Series NB

VM 528 GB/12.05 Ident No. 795 261 11

n = 1450/1750 min-


Pump dimensions


Pumpsize

Motorsize

Perfor-mance

Flanges Feet


Extensiondim.

mm kW DNsDNd a f a2 b1 b2 f1 h1 h2 b c m1 m2 n1 n2 s a1 d h3 l1 l x



ring


v. page 2

80 0,55 0,75 162 124 234 463 19/200

90 S 1,1 181 130 282 511 24/200

90 L 1,5

200

181 130 282 511 24/20032-160/01

100 L 2,2 3

50 32 80 149 - 130 130 - 132 160 50 15 100 70 240 190 M12

250 203 158 312 541

102

28/250

80 0,55 0,75 162 124 234 463 19/200

90 S 1,1 181 130 282 511 24/200

90 L 1,5

200

181 130 282 511 24/20032-200/01

100 L 2,2 3

50 32 80 149 - 124 130 - 160 180 50 15 100 70 240 190 M12

250 203 158 312 541

102

28/250

80 0,55 0,75 162 124 234 497 19/200

90 S 1,1 181 130 282 545 24/200

90 L 1,5

183 200

181 130 282 545 24/2002/32-200/01

100 L 2,2 3

50 32 80

193

- 124 130 - 160 180 50 15 100 70 240 190 M12

250 203 158 312 585

102

28/250

80 0,55 0,75 162 124 234 463 19/200

90 S 1,1 181 130 282 511 24/200

90 L 1,5

200

181 130 282 511 24/200

40-160/01

100 L 2,2 3

65 40 80 149 - 130 130 - 132 160 50 15 100 70 240 190 M12

250 203 158 312 541

102

28/250

80 0,55 0,75 162 124 234 483 19/200

90 S 1,1 181 130 282 531 24/200

90 L 1,5

200

181 130 282 531 24/200

100 L 2,2 3 203 158 312 561 28/250

40-200/01

112 M 4

65 40 100 149 - 125 135 - 1 60 180 50 15 100 70 265 212 M12

250228 171 335 584

102

28/250

90 S 1,1 181 130 282 531 24/200

90 L 1,5200

181 130 282 531 24/200

100 L 2,2 3 203 158 312 561 28/25040-250/01

112 M 4

65 40 100 149 - 150 156 - 1 80 225 65 15 125 95 320 250 M12

250228 171 335 584

85

28/250

110 L 2,2 3 203 158 312 605 28/250

112 M 4193 250

228 171 335 628 28/250

132 S 5,5 266 196 375 713 38/300

132 M 7,5

238 300

266 196 375 713 38/300

2/40-250/01

160 M 11

65 40 100

274

- 150 156 - 180 225 65 15 125 95 320 250 M12

350 320 234 481 855

85

42/350

80 0,55 0,75 162 124 234 483 19/200

90 S 1,1 181 130 282 531 24/200

90 L 1,5

200

181 130 282 531 24/20050-160/01

100 L 2,2 3

65 50 100 149 - 123 130 - 1 60 180 50 15 100 70 265 212 M12

250 203 158 312 561

102

28/250

80 0,55 0,75 162 124 234 483 19/200

90 S 1,1 181 130 282 531 24/200

90 L 1,5

200

181 130 282 531 24/200

100 L 2,2 3 203 158 312 561 28/250

112 M 4

149

250228 171 335 584 28/250

50-200/01

132 S 5,5

65 50 100

204

- 133 145 - 160 200 50 15 100 70 265 212 M12

300 266 196 375 679

102

38/300

90 L 1,5 200 181 130 282 531 24/200

100 L 2,2 3 203 158 312 561 28/250

112 M 4

149250

228 171 335 584 28/250132 S 5,5 266 196 375 679 38/300

132 M 7,5204 300

266 196 375 679 38/300

50-250/01

160 M 11

65 50 100

219

- 156 169 - 180 225 65 15 125 95 320 250 M 12

350 320 234 481 800

85

42/350

100 L 2,2 3 203 158 312 605 28/250

112 M 4193 250

228 171 335 628 28/250

132 S 5,5 266 196 375 713 38/300

132 M 7,5238 300

266 196 375 713 38/300

160 M 11 320 234 481 855 42/350

2/50-250/01

160 L 15

65 50 100

274

- 156 169 - 180 225 65 15 125 95 320 250 M12

350320 234 481 855

85

42/350

80 0,55 0,75 162 124 234 483 19/200

90 S 1,1 181 130 282 531 24/200

90 L 1,5

200

181 130 282 531 24/200

100 L 2,2 3 203 158 312 561 28/250

30

65-160/01

112 M 4

80 65 100 149 - 133 162 - 1 60 200 65 15 125 95 280 212 M12

250228 171 335 584

102

28/250

The motor dimensions as indicated are approximatedimensions. Exact data depend on the motor make.

When using special motors, make sure that other performances are allocated to the in-dividual sizes, depending upon the enclosure. The main dimensions change accord-ingly. In case of order, binding tables of motor dimensions must be supplied to us.


12/20

Series NB

VM 528 GB/12.05 Ident No. 795 26112

n = 1450/1750 min-

Aggregate dimensions: Sizes with shaft diameter 30 and 40at the shaft seal

Shaftdiameter

at the shaftseal

Connections

Drain-ing

Fill-ing

Vent-ing

Pressuremeasurement

mm FD FF FV PM2

30 G 1/4 G 1/4 G 1/4 G 1/4

40 G 3/8 G 3/8 G 3/8 G 3/8

Flanges: up to DN 150 acc. to EN 1092-2 PN 16 as from DN 200 acc. to EN 1092-2 PN 10

DNdDNs

D bf k gNo. ofholes

65 185 20 145 19 480 200 22 160 19 8

100 220 24 180 19 8

125 250 26 210 19 8

150 285 26 240 23 8

200 340 26 295 23 8



Pump dimensions


Pumpsize Motorsize Perfor-mance

Flanges Feet


Extensiondim.


Allocationstub shaft/motor bracket/

intermediate ring


v. page 2

90 S 1,1 181 130 282 531 24/200

90 L 1,5250

181 130 282 531 24/200

100 L 2,2 3 203 158 312 561 28/250

112 M 4

149

250228 171 335 584 28/250

132 S 5,5 266 196 375 679 38/300

65-200/02

132 M 7,5

80 65 100

204

- 148 170 - 180 225 65 15 125 95 320 250 M 12

300266 196 375 679

85

38/300

80 0,55 0,75 162 124 234 508 19/200

90 S 1,1 181 130 282 556 24/200

90 L 1,5

200

181 130 282 556 24/200

100 L 2,2 3 203 158 312 586 28/250

112 M 4

149

250

228 171 335 609 28/250132 S 5,5 266 196 375 704 38/300

80-160/01

132 M 7,5

100 80 125

204

- 136 170 - 180 225 65 15 125 95 320 250 M12

300266 196 375 704

102

38/300

90 S 1,1 181 130 282 556 24/200

90 L 1,5200

181 130 282 556 24/200

100 L 2,2 3 203 158 312 586 28/250

112 M 4

149

250228 171 335 609 28/250

132 S 5,5 266 196 375 704 38/300

30

100-160/01

132 M 7,5

125 100 125

204

- 165 200 - 200 280 65 15 125 95 320 250 M 12

300266 196 375 704

102

38/300

100 L 2,2 3 203 158 312 673 28/250

112 M 4261 250

228 171 335 696 28/250

132 S 5,5 266 196 375 756 38/300

132 M 7,5281 300

266 196 375 756 38/300

160 M 11 320 234 481 892 42/350

160 L 15 320 234 481 892 42/350

65-250/01

180 M 22

80 65 100

311

360 164 184 261 200 250 80 18 160 120 360 280 M16

350

375 275 610 1021

123

48/350

112 M 4 261 250 228 171 335 721 28/250

132 S 5,5 266 196 375 781 38/300132 M 7,5

281 300266 196 375 781 38/300

160 M 11 320 234 481 917 42/350

160 L 15 320 234 481 917 42/350

180 M 18,5 375 275 610 1046 48/350

180 L 22

350

375 275 610 1046 48/350

40

65-315/01

200 L 30

80 65 125

311

360 202 219 261 225 280 80 25 160 120 400 315 M16

400 415 310 665 1101

105

55/400


13/20

Series NB

VM 528 GB/12.05 Ident No. 795 261 13

n = 1450/1750 min-


Pump dimensions

Shaftdiameterat shaft

seal

Pumpsize

Motorsize

Perfor-mance

Flanges Feet


Extensiondim.

mm kW DNs DNd a f a2 b1 b2 f1 h1 h2 b c m1 m2 n1 n2 s a1 d H3 l1 l x



ring


v. page 2

132 M 7,5 281 300 266 196 375 781 38/300160 M 11 320 234 481 917 42/350

160 L 15 320 234 481 917 42/350

180 M 18,5 375 275 610 1046 48/350

180 L 22

350

375 275 610 1046 48/350

65-400/01

200 L 30

80 65 125311

360 239 255 261 250 355 80 25 160 120 420 335 M16

400 415 310 665 1101

105

55/400

100 L 2,2 3 203 158 312 698 28/250

112 M 4261 250

228 171 335 721 28/250

132 S 5,5 266 196 375 781 38/300

132 M 7,5281 300

266 196 375 781 38/300

80-200/02

160 M 11

100 80 125

311

360 163 188 261 180 250 65 1 8 125 95 345 280 M12

350 320 234 481 917

123

42/350

112 M 4 261 250 228 171 335 721 28/250

132 S 5,5 266 196 375 781 38/300

132 M 7,5281 300

266 196 375 781 38/300

160 M 11 320 234 481 917 42/350

160 L 15 320 234 481 917 42/350

180 M 18,5 375 275 610 1046 48/350

180 L 22

350

375 275 610 1046 48/350

80-250/01

200 L 30

100 80 125

311

360 182 208 261 200 280 80 18 160 120 400 315 M16

400 415 310 665 1101

123

55/400

132 S 5,5 266 196 375 781 38/300

132 M 7,5281 300

266 196 375 781 38/300

160 M 11 320 234 481 917 42/350

160 L 15 320 234 481 917 42/350

180 M 18,5 375 275 610 1046 48/350

180 L 22

350

375 275 610 1046 48/350

80-315/01

200 L 30

100 80 125

311

360 210 231 261 250 315 80 25 160 120 400 315 M16

400 415 310 665 1101

105

55/400

100 L 2,2 3 203 158 312 698 28/250

112 M 4261 250

228 171 335 721 28/250

132 S 5,5 266 196 375 781 38/300

132 M 7,5281 300

266 196 375 781 38/300

160 M 11 320 234 481 917 42/350

100-200/01

160 L 15

125 100 125

311

360 165 203 261 200 280 80 18 160 120 360 280 M16

350

320 234 481 917

133

42/350112 M 4 261 250 228 171 335 736 28/250

132 S 5,5 266 196 375 796 38/300

132 M 7,5281 300

266 196 375 796 38/300

160 M 11 320 234 481 932 42/350

160 L 15 320 234 481 932 42/350

180 M 18,5 375 275 610 1061 48/350

180 L 22

350

375 275 610 1061 48/350

100-250/01

200 L 30

125 100 140

311

360 189 224 261 225 280 80 18 160 120 400 315 M16

400 415 310 665 1116

133

55/400

132 M 7,5 281 300 266 196 375 796 38/300

160 M 11 320 234 481 932 42/350

160 L 15 320 234 481 932 42/350

180 M 18,5 375 275 610 1061 48/350

180 L 22

350

375 275 610 1061 48/350

100-315/01

200 L 30

125 100 140311

360 220 250 261 250 315 80 25 160 120 400 315 M16

400 415 310 665 1116

112

55/400

132 M 7,5 281 300 266 196 375 796 38/300

160 M 11 320 234 481 932 42/350160 L 15 320 234 481 932 42/350

180 M 18,5 375 275 610 1061 48/350

180 L 22

350

375 275 610 1061 48/350

125-200/01

200 L 30

150 125 140311

360 196 236 261 250 315 80 18 160 120 400 315 M16

400 415 310 665 1116

143

55/400

132 M 7,5 281 300 266 196 375 796 38/300

160 M 11 320 234 481 932 42/350

160 L 15 320 234 481 932 42/350

180 M 18,5 375 275 610 1061 48/350

180 L 22

350

375 275 610 1061 48/350

125-250/01

200 L 30

150 125 140311

360 212 255 261 250 355 80 18 160 120 400 315 M16

400 415 310 665 1116

143

55/400

132 M 7,5 281 300 266 196 375 796 38/300

160 M 11 320 234 481 932 42/350

160 L 15 320 234 481 932 42/350

180 M 18,5 375 275 610 1061 48/350

180 L 22

350

375 275 610 1061 48/350

40

150-200/01

200 L 30

200 150 160311

360 214 268 261 280 370 100 27 200 150 550 450 M20

400 415 310 665 1116

143

55/400


When using special motors, make sure that other performances are allocated to the indi-vidual sizes, depending upon the enclosure. The main dimensions change accordingly. Incase of order, binding tables of motor dimensions must be supplied to us.


14/20

Series NB

VM 528 GB/12.05 Ident No. 795 26114

n = 2900/3500 min-

Aggregate dimensions: Sizes with shaft diameters 16, 24 and 30at the shaft seal

Shaftdiameter

at the shaftseal

Connections

Drain-ing

Fill-ing

Vent-ing

Pressuremeasurement

mm FD FF FV PM2

16 G 1/4 G 1/4 G 1/8 G 1/4

24, 30 G 1/4 G 1/4 G 1/4 G 1/4

Connections at sizes 25-200 and 2/25-200: FD = G 1/2;FF at sizes 20-160, 25-200 and 2/25-200 not existent.


DNdDNs

D bf k gNo. ofholes

25 115 16 85 14 4

32 140 18 100 19 4

40 150 18 110 19 4

50 165 20 125 19 4

65 185 20 145 19 4

Tolerances of companion dimensions Sense of rotation: clockwise as seen Dimensions in mm

acc. to DIN EN 735 from the driving side without commitment


Pump dimensions


seal

Pumpsize

Motorsize

Perfor-mance

Flanges Feet


Extensiondim.




ring


v. page 2

80 0,75 1,1 162 124 234 435 19/200

90 S 1,5 181 130 282 483 24/200

90 L 2,2

138 200

181 130 282 483 24/200

100 L 3 203 158 312 523 28/250

20-160/01

112 M 4

25 25 63

148

- 108 108 - 112 145 50 14 100 70 220 180 M10

250228 171 335 546

62

28/250

80 0,75 1,1 162 124 234 435 19/200

90 S 1,5 181 130 282 483 24/200

90 L 2,2

138 200

181 130 282 483 24/200100 L 3 203 158 312 523 28/250

16

25-160/01

112 M 4

25 25 63

148

- 100 108 - 112 160 50 12 100 70 220 180 M10

250228 171 335 546

62

28/250

80 0,75 1,1 162 124 234 462 19/200

90 S 1,5 181 130 282 510 24/200

90 L 2,2

200

181 130 282 510 24/200

100 L 3 203 158 312 540 28/250

112 M 4

148

250228 171 335 563 28/250

32-125/01

132 S 5,5 7,5

50 32 80

188

- 96 96 - 112 140 50 15 100 70 190 140 M12

300 266 196 375 643

89

38/300

80 0,75 1,1 162 124 234 462 19/200

90 S 1,5 181 130 282 510 24/200

90 L 2,2

200

181 130 282 510 24/200

100 L 3 203 158 312 540 28/250

112 M 4

148

250228 171 335 563 28/250

40-125/01

132 S 5,5 7,5

65 40 80

188

- 96 110 - 112 140 50 15 100 70 210 160 M12

300 266 196 375 643

89

38/300

90 S 1,5 181 130 282 530 24/200

90 L 2,2 200 181 130 282 530 24/200

100 L 3 203 158 312 560 28/250

112 M 4

148

250228 171 335 583 28/250

132 S 5,5 7,5 188 300 266 196 375 663 38/300

24

50-125/01

160 M 11 15

65 50 100

223

- 110 130 - 132 160 50 15 100 70 240 190 M12

350 320 234 481 804

89

42/350


15/20

Series NB

VM 528 GB/12.05 Ident No. 795 261 15

n = 2900/3500 min-


Pump dimensions


seal

Pumpsize

Motorsize

Perfor-mance

Flanges Feet


Extensiondim.



motor bracket/intermediate ring


v. page 2

90 L 2,2 200 181 130 282 530 24/200100 L 3 203 158 312 560 28/250

112 M 4

148250

228 171 335 583 28/250

132 S 5,5 7,5 188 300 266 196 375 663 38/300

160 M 11 15 320 234 481 804 42/350

24 65-125/01

160 L 18,5

80 65 100

223

- 120 148 - 160 180 65 15 125 95 280 212 M12

350320 234 481 804

95

42/350

100 L 3 203 158 312 541 28/250

112 M 4149 250

228 171 335 564 28/250

132 S 5,5 7,5 204 300 266 196 375 659 38/30025-200/01

160 M 11 15

40 25 80

219

- 132 132 - 160 180 50 15 100 70 240 190 M12

350 320 234 481 780

102

42/350

112 M 4 193 250 228 171 335 608 28/250

132 S 5,5 7,5 238 300 266 196 375 693 38/300

160 M 11 15 320 234 481 835 42/3502/25-200/01

160 L 18,5

40 25 80

274

- 132 132 - 160 180 50 15 100 70 240 190 M12

350320 234 481 835

102

42/350

100 L 3 203 158 312 541 28/250

112 M 4149 250

228 171 335 564 28/250

132 S 5,5 7,5 204 300 266 196 375 659 38/30032-160/01

160 M 11 15

50 32 80

219

- 130 130 - 132 160 50 15 100 70 240 190 M12

350 320 234 481 780

102

42/350

100 L 3 203 158 312 541 28/250

112 M 4149 250

228 171 335 564 28/250

132 S 5,5 7,5 204 300 266 196 375 697 38/300

160 M 11 15 320 234 481 780 42/350

160 L 18,5 320 234 481 780 42/350

32-200/01

180 M 22

50 32 80

219

- 124 130 - 160 180 50 15 100 70 240 190 M12

350

375 275 610 909

102

48/350

112 M 4 193 250 228 171 335 608 28/250

132 S 5,5 7,5 238 300 266 196 375 693 38/300

160 M 11 15 320 234 481 835 42/350

160 L 18,5 320 234 481 835 42/350

180 M 22

350

375 275 610 964 48/350

2/32-200/01

200 L 30 37

50 32 80

274

- 124 130 - 160 180 50 15 100 70 240 190 M12

400 415 310 665 1019

102

55/400

100 L 3 203 158 312 541 28/250

112 M 4

149 250

228 171 335 564 28/250132 S 5,5 7,5 204 300 266 196 375 659 38/300

160 M 11 15 320 234 481 780 42/350

40-160/01

160 L 18,5

65 40 80

219

- 130 130 - 132 160 50 15 100 70 240 190 M12

350320 234 481 780

102

42/350

100 L 3 203 158 312 561 28/250

112 M 4149 250

228 171 335 584 28/250

132 S 5,5 7,5 204 300 266 196 375 679 38/300

160 M 11 15 320 234 481 800 42/350

160 L 18,5 320 234 481 800 42/350

180 M 22

350

375 275 610 929 48/350

40-200/01

200 L 30 37

65 40 100

219

- 125 135 - 160 180 50 15 100 70 265 212 M12

400 415 310 665 984

102

55/400

132 S 5,5 7,5 204 300 266 196 375 679 38/300

160 M 11 15 320 234 481 800 42/350

160 L 18,5 320 234 481 800 42/350

180 M 22

350

375 275 610 929 48/350

40-250/01

200 L 30 37

65 40 100219

- 150 156 - 180 225 65 15 125 95 320 250 M12

400 415 310 665 984

85

55/400

160 M 11 15 320 234 481 855 42/350160 L 18,5 320 234 481 855 42/350

180 M 22

350

375 275 610 984 48/3502/40-250/01

200 L 30 37

65 40 100 274 - 150 156 - 1 80 225 65 1 5 125 95 320 250 M12

400 415 310 665 1039

85

55/400

100 L 3 203 158 312 561 28/250

112 M 4149 250

228 171 335 584 28/250

132 S 5,5 7,5 204 300 266 196 375 679 38/300

160 M 11 15 320 234 481 800 42/350

160 L 18,5 320 234 481 800 42/350

30

50-160/01

180 M 22

65 50 100

219

- 123 130 - 160 180 50 15 100 70 265 212 M12

350

375 275 610 929

102

48/350


When using special motors, make sure that other performances are allocated to the indi-vidual sizes, depending upon the enclosure. The main dimensions change accordingly. Incase of order, binding tables of motor dimensions must be supplied to us.


16/20

Series NB

VM 528 GB/12.05 Ident No. 795 26116

n = 2900/3500 min-

Aggregate dimensions Sizes with shaft diameters 30 and 40at the shaft seal

Shaftdiameter

at the shaftseal

Connections

Drain-ing

Fill-ing

Vent-ing

Pressuremeasurement

mm FD FF FV PM2

30 G 1/4 G 1/4 G 1/4

G 1/4

40 G 3/8 G 3/8 G 3/8 G 3/8


DNdDNs

D bf k gNo. ofholes

50 165 20 125 19 4

65 185 20 145 19 4

80 200 22 160 19 8

100 220 24 180 19 8

125 250 26 210 19 8



Pump dimensions


Pumpsize

Motorsize

Perfor-mance

Flanges Feet


Extensiondim.





v. page 2

112 M 4 149 250 228 171 335 584 28/250

132 S 5,5 7,5 204 300 266 196 375 679 38/300

160 M 11 15 320 234 481 800 42/350

160 L 18,5 320 234 481 800 42/350

180 M 22

350

375 275 610 929 48/350

50-200/01

200 L 30 37

65 50 100

219

- 1 33 145 - 1 60 200 50 15 100 70 265 212 M12

400 415 310 665 984

102

55/400

132 S 5,5 7,5 204 300 266 196 375 679 38/300

160 M 11 15 320 234 481 800 42/350

160 L 18,5 320 234 481 800 42/350

180 M 22

350

375 275 610 929 48/350

50-250/01

200 L 30 37

65 50 100219

- 1 56 169 - 1 80 225 65 15 125 95 320 250 M12

400 415 310 665 984

85

55/400

160 M 11 15 320 234 481 855 42/350

160 L 18,5 320 234 481 855 42/350

180 M 22

350

375 275 610 984 48/3502/50-250/01

200 L 30 37

65 50 100 274 - 156 169 - 180 225 65 15 125 95 320 250 M12

400 415 310 665 1039

85

55/400

112 M 4 149 250 228 171 335 584 28/250

132 S 5,5 7,5 204 300 266 196 375 679 38/300

160 M 11 15 320 234 481 800 42/350

160 L 18,5 320 234 481 800 42/350

180 M 22

350

375 275 610 929 48/350

65-160/01

200 L 30 37

80 65 100

219

- 1 33 162 - 1 60 200 65 15 125 95 280 212 M12

400 415 310 665 984

102

55/400

132 S 5,5 7,5 204 300 266 196 375 679 38/300160 M 11 15 320 234 481 800 42/350

160 L 18,5 320 234 481 800 42/350

180 M 22

350

375 275 610 929 48/350

30

65-200/02

200 L 30 37

80 65 100219

- 1 48 170 - 1 80 225 65 15 125 95 320 250 M12

400 415 310 665 984

85

55/400


17/20

Series NB

VM 528 GB/12.05 Ident No. 795 261 17

n = 2900/3500 min-


Pump dimensions


Pumpsize

Motorsize

Perfor-mance

Flanges Feet


Extensiondim.





v. page 2

112 M 4 149 250 228 171 335 609 28/250132 S 5,5 7,5 204 300 266 196 375 704 38/300

160 M 11 15 320 234 481 825 42/350

160 L 18,5 320 234 481 825 42/350

180 M 22

350

375 275 610 954 48/350

80-160/01

200 L 30 37

100 80 125

219

- 136 170 - 180 225 65 15 125 95 320 250 M12

400 415 310 665 1009

102

55/400

132 S 5,5 7,5 204 300 266 196 375 704 38/300

160 M 11 15 320 234 481 825 42/350

160 L 18,5 320 234 481 825 42/350

180 M 22

350

375 275 610 954 48/350

30

100-160/01

200 L 30 37

125 100 125219

- 165 200 - 200 280 65 15 125 95 320 250 M12

400 415 310 665 1009

102

55/400

160 L 18,5 320 234 481 892 42/350

180 M 22350

375 275 610 1021 48/35065-250/01

200 L 30 37

80 65 100 311 360 164 184 261 200 250 80 18 160 120 360 280 M16

400 415 310 665 1076

123

55/400

160 M 11 15 320 234 481 917 42/350

160 L 18,5 320 234 481 917 42/350

180 M 22

350

375 275 610 1046 48/35080-200/02

200 L 30 37

100 80 125 311 360 163 188 261 180 250 65 18 125 95 345 280 M12

400 415 310 665 1101

123

55/400

160 M 11 15 320 234 481 917 42/350

160 L 18,5 320 234 481 917 42/350

180 M 22

350

375 275 610 1046 48/350

40

100-200/01

200 L 30 37

125 100 125 311 360 165 203 261 200 280 80 18 1 60 120 360 280 M16

400 415 310 665 1101

133

55/400


When using special motors, make sure that other performances are allocated to the individ-ual sizes, depending upon the enclosure. The main dimensions change accordingly. In caseof order, binding tables of motor dimensions must be supplied to us.


18/20

Series NB

VM 528 GB/12.05 Ident No. 795 26118


19/20

ALLWEILER Solutions

VM 528 GB/12.05 Ident No. 795 261 19

Successful in important branches

Decades of experience and branch-specific know-how ensure solutions that are practical and dependable. In addition to individualunits with a motor or with a free shaft end, you can get complete systems and customer-specific cast parts from ALLWEILER AG.You are not just investing in machines with ALLWEILER AG. You are also profiting from decades of know-how about applicationsand processes in your branch.

You will find pumps and systems by ALLWEILER AG in the following sectors:

Marine and OffshoreMade of particularly corrosion-resistant, saltwater-proof mate-rials and in accordance with specific standards (shock testing,national marine, international classifications, etc.).

Power GenerationBlock and twin units for fuel and water injection in gas andsteam turbines.For fuel supply, injection and lubricating oil delivery in powerplants.

Water and WastewaterPumps for water treatment; share of dry solids content up to45 percent; macerators, which make is possible to pump de-livery media that are high in fibre and solids.

Process Engineering and Chemical Industry (ATEX-conformity)Shaft bearing, shaft seal and material designs in accordancewith the chemical characteristics of the delivery media. Mag-netic coupling for hermetically sealed pumps.

Building IndustrySpecial units for oil furnace and lift systems. oil submersiblepumps for all types of hydraulic machines.

Food and PharmaStainless steel pumps with CIP and SIP design, EHEDG andFDA certified. Especially for the careful delivery and propor-tioning of even sticky, paste-like and solids-rich media.

Tool Machinery

Designed for large delivery amounts or a high delivery pres-sure; resistant to contaminants and foreign materials. Espe-cially for cooling lubricant supply.

Pulp and PaperPumps with extremely high availability (24 hours; 365 days)and many sizes, starting with small proportioning pumps andranging to large Kaolin feeding pumps.

Heat TransferIn supply circuits, circulating systems and heating circuits forthe delivery of hot water and heat-transfer oil up to

207 C and 450 C.


20/20

Series NB

ubject to technical alterations.

ALLWEILER AG

Postfach 1140 78301 RadolfzellAllweilerstr. 1 78315 RadolfzellGermanyTel. +49 (0)7732 86-0Fax. + 49 (0)7732 86-436E-Mail: [email protected]: http://www allweiler com

324-31283 allweiller pmup

Documents