heat and mass transferocw.snu.ac.kr/sites/default/files/note/548.pdf · engineers prefer to work...
Post on 05-Nov-2019
1 Views
Preview:
TRANSCRIPT
이 윤 우
서울대학교 화학생물공학부
Heat and Mass Transfer
22 HEAT TRANSFER
WITH LAMINAR FLOW
Some problems of heat transfer in a fluid in laminar flow
Governing Equations
Supercritical Fluid Process Lab
Differential energy balance
Solution of velocity profile and temperature profile
for problems of laminar flow
Equation of continuityNavier-Stokes equations
Solution of velocity profile for problems
of isothermal laminar flow
Developing vs. Developed
Developing flowThe flow pattern varies with the distance from the leading edge of the system. This occurs with all external flow systems and also near the inlet of all internal flow system
Developed flow (Idealized system)The flow pattern is the same at all cross sections normal to flow. This is called “developed” flow and occurs only in internal flow systems far from the entrance.
Supercritical Fluid Process Lab
Idealization
Supercritical Fluid Process Lab
- All flow systems must have some entrance effect.
- The physical properties of all fluids are dependent on temperature and differ at all points in a non-isothermal system.
- In a system transferring heat, a uniform flow pattern is never developed even at great distances from the entrance.
- The solution of the differential balances when the physical properties vary throughout the system is quite difficult.
For idealized systems developed flow is an attainable condition.
assume that these physical properties are
constant.Idealization
Engineers prefer to work with hx
Supercritical Fluid Process Lab
Equation expressing temperatureas a function of position and velocity
Equation for heat transfer coefficient
대부분 열전달 문제에서는 온도분포가 위치와 유속의 함수로 표현되면 충분한 정보를 얻을 수 있다.
엔지니어들은 열전달능력을 열전달계수로 표현하여 왔기 때문에 적절한 절차를 통하여 위의 방정식을 열전달계수로 표현하는 식으로 바꾸는 것이 필요하다.
Two simple Systems
1. Heat transfer between a fluid and a flat platedifferential energy balance
temperature as a function of position, free stream velocity.
2. A fluid being heated in a pipedifferential energy balance
temperature as a function of position, velocity.
Heat transfer coefficient for laminar flow have a strong dependence on position. This is not usually the case for heat transfer with turbulent flow.
Supercritical Fluid Process Lab
Heat transfer with laminar flow parallel to a flat plate
Heat Transfer with a Developing Velocity Distribution
E. Pohlhausen, Z. angew. Math.u.Mach., 1:15 (1921)
U0
U0
U0
Supercritical Fluid Process Lab
50 105Re ×<=ν
xu
Momentum & Energy Balances
⎟⎟⎠
⎞⎜⎜⎝
⎛∂∂
=∂∂
+∂∂
⎟⎟⎠
⎞⎜⎜⎝
⎛∂∂
=∂∂
+∂∂
⎟⎟⎠
⎞⎜⎜⎝
⎛∂∂
+∂∂
+∂∂
=∂∂
+∂∂
+∂∂
+∂∂
2
2
2
2
2
2
2
2
2
2
yu
yuu
xuu
yt
Ck
ytu
xtu
zt
yt
xt
Ckt
ztu
ytu
xtu
xxy
xx
pyx
pzyx
ρμ
ρ
ρθ
Energy balance for incompressible flow without heat generation
If the flow is two-dimensional, Uz=0.
steady state0
(8-11)
(22-1)
(22-2)
Conduction only y-direction
Momentum equation
E. Pohlhausen
Supercritical Fluid Process Lab
Velocity distribution in the laminar boundary layer
11886542
0
3
3
2
2
0
0
3
3
2
22
2
2
104277.1104972.2105943.416603.0
1,,
0,00,0
0)(2)()(
)(
η×−η×+η×−η=
=′∞=η⇒=∞=
=′==η⇒===
=ηη
+ηη
η
ν
ψ=η
ν=η
∂ψ∂
ν=∂ψ∂
∂ψ∂
−∂∂ψ∂
∂ψ∂
∂ψ∂
−=∂ψ∂
=
⎟⎟⎠
⎞⎜⎜⎝
⎛
∂
∂ρμ
=∂∂
+∂∂
−−−f
fatuuyat
ffatuuyat
dfd
dfdf
uxfand
xu
y
yyxyxy
xuand
yu
yu
yu
ux
uu
x
yx
yx
xxy
xx
E. Pohlhausen
Supercritical Fluid Process Lab
(22-1)
(11-17)
(11-15) (11-16)
(11-22)solution
Velocity distribution in the laminar boundary layerE. Pohlhausen
Supercritical Fluid Process Lab
xu
yν
=η 0
0)(
uu
f x=η′
1.0
0.8
0.6
0.4
0.2
00 1 2 3 4 5 6
Fig. 11-8 (page 145)
Boundary Layer Thickness in the laminar boundary layerE. Pohlhausen
Supercritical Fluid Process Lab
00.5
uxν
=δ
Hydrodynamic Boundary Layer Thickness (HBLT)
(11-22)
The Prandtl Number
kCpμ
αν
=≡Pr
Thermal diffusivity
Kinematic viscosity
E. Pohlhausen
Supercritical Fluid Process Lab
If Pr=1, Momentum balance = Energy Balances
⎟⎟⎠
⎞⎜⎜⎝
⎛
∂
∂ρμ
=∂∂
+∂∂
⎟⎟⎠
⎞⎜⎜⎝
⎛
∂∂
ρ=
∂∂
+∂∂
2
2
2
2
yu
yu
ux
uu
yt
Ck
ytu
xtu
xxy
xx
pyx
E. Pohlhausen
Supercritical Fluid Process Lab
kCpμ
αν
=≡Pr Prantle 수가 1인 경우에는 thermal
diffusivity와 kinematic viscosity가 같아
진다. 더욱이 온도 t를 다음과 같은 무차
원 온도
로 바꾸면 오른쪽의 두식은 같은 경계조
건을 같게 된다.
0tttt
s
s
−−
평판의 온도가 ts로서 유체의 온도 t0 보다 높은 경우를 생각하자.
(22-1)
(22-2)
Boundary conditions
1,1 ,0at x
1,1 ,yat
0,0 0,yat
00
00
00
==−−
=
==−−
∞=
==−−
=
uu
tttt
uu
tttt
uu
tttt
x
s
s
x
s
s
x
s
s
E. Pohlhausen
Supercritical Fluid Process Lab
SolutionE. Pohlhausen
Supercritical Fluid Process Lab
Pr=1일 경우에는 (22-1)과 (22-2)는 동일한 해를 같게 된다. 따라서 주어진 위치 (x,y)에서 무차원 온도 (ts-t)/(ts-t0)와 무차원 속도 ux/u0는 서로 같다. 이런 경우 열전달과 운동량전달은 서로 직접적으로 상사성을 지니며 thermal boundary layer와 hydrodynamic boundary layer는 서로 같게된다.
xu
yν
=η 0
0)(
tttt
fs
s
−−
=η′
1.0
0.8
0.6
0.4
0.2
00 1 2 3 4 5 6
Boundary Layer Thickness in the laminar boundary layerE. Pohlhausen
Supercritical Fluid Process Lab
0
0.5u
xαδ =
Thermal Boundary Layer Thickness (TBLT)
(11-22)
Pr = 1
Equation (22-1) and (22-2) are identical when applied to fluids with a Pr=1.
Therefore they have identical solutions; i.e., for any point (x,y) in the flow system, the dimensionless temperature (ts-t)/(ts-t0) and velocity variables (ux/u0) are equal.
The thermal and hydrodynamic boundary layers are of equal thickness.
Valid for many gases and liquid whose Pr~1.
E. Pohlhausen
Supercritical Fluid Process Lab
The Prandtl NumberE. Pohlhausen
Supercritical Fluid Process Lab
Vapor Temp(K) PrAir 300 0.707
600 0.685900 0.720
1200 0.728NH3 300 0.887CO2 300 0.766CO 300 0.730He 300 0.680H2 300 0.701N2 300 0.716O2 300 0.711H2O(v) 700 1.00
@ 1atm
Liquid Temp(K) PrEngine Oil 273 47,000
300 6,400400 152
EG 273 617300 151370 23.7
Freon-12 230 5.9300 3.5
Mercury 273 0.0290500 0.0103
Bismuth 589 0.0142Lead 755 0.0170
Pr ~1 Pr ≠1
Pohlhausen’s solution; Pr≠1
xuyν
η 0=0
)(ux
ψfν
=ηLet
)(ψ0 ηfu
yux ′=
∂∂
=
])()('[21 0 η−ηη
ν=
∂∂
−= ffxu
xψuy
then
[ ] 02
)(Pr 02
0
2
=⎟⎟⎠
⎞⎜⎜⎝
⎛−−
+⎟⎟⎠
⎞⎜⎜⎝
⎛−−
ηη
η dttttd
fd
ttttd
s
s
s
sEq (22-1)Become ODE (22-3)
E. Pohlhausen
Supercritical Fluid Process Lab
⎟⎟⎠
⎞⎜⎜⎝
⎛
∂∂
ρ=
∂∂
+∂∂
2
2
yt
Ck
ytu
xtu
pyx (22-1)
s
s
tttty−−
=∞
Heat transfer with laminar flow parallel to a flat plate
[ ] 02
)(Pr2
2
=+η
ηη d
dYfd
Yd
Let
1Y ,η ,y0Y 0,η 0,y
=∞=∞====
E. Pohlhausen
Supercritical Fluid Process Lab
(22-4)
then, Equation (22-3) yields
pddY =η/
Heat transfer with laminar flow parallel to a flat plate
[ ]
[ ] ηη
ηη
dfp
dp
pfddp
2)(Pr
02
)(Pr
−=
=+
Let
E. Pohlhausen
Supercritical Fluid Process Lab
(22-5)
then, Equation (22-4) yields
(22-6)
η=⎟
⎠⎞
⎜⎝⎛ ηη−= ∫
η
ddYdfCp
01 )(
2exp Pr (22-7)
Integrating yields
Heat transfer with laminar flow parallel to a flat plate
20 0
1 )(2
exp CddfCY +η⎟⎟
⎠
⎞
⎜⎜
⎝
⎛ηη−= ∫ ∫
η ηPr
η⎟⎟
⎠
⎞
⎜⎜
⎝
⎛ηη−
=
=
∫ ∫∞ η
ddf
C
C
0 0
1
2
)(2
exp
1
0
Pr
ηηη
ηηη
η
η η
ddf
ddf
ttttY
s
s
∫ ∫
∫ ∫∞
⎟⎟⎠
⎞⎜⎜⎝
⎛−
⎟⎟⎠
⎞⎜⎜⎝
⎛−
=−−
=
0 0
0 0
0 )(2Prexp
)(2PrexpComplete
SolutionFor temp.ProfileFig. 22-1
(22-10)
E. Pohlhausen
Supercritical Fluid Process Lab
(22-8)
(22-9)
Integrating second time gives
0,0 == Yη
1, =∞= Yη
Heat transfer with laminar flow parallel to a flat plate
η⎟⎟
⎠
⎞
⎜⎜
⎝
⎛ηη−
η⎟⎟
⎠
⎞
⎜⎜
⎝
⎛ηη−
=
∫ ∫
∫ ∫∞ η
η η
ddf
ddf
Y
0 0
0 0
)(2
exp
)(2
exp
Pr
Pr
E. Pohlhausen
Supercritical Fluid Process Lab
The value of f(n) which were determined for the isothermal-flow problem are represented by a series given below.
11886542 104277.1104972.2105943.416603.0)( η×−η×+η×−η=η −−−f
They were used Pohlhausen to obtain the temperature profiles for fluids with a wide range of Prandtl numbers.
(11-22)
Temperature for laminar flow past a flat plate at uniform temperature
Supercritical Fluid Process Lab
Fig. 22-1
Heat transfer with laminar flow parallel to a flat plateE. Pohlhausen
Supercritical Fluid Process Lab
A local Reynolds number and is usually written Rex indicating that it applies at a distance x from the leading edge of the plate.
2/100 Re xxyxu
xy
xu
y =ν
=ν
=η
νxu0Re =
Heat Transfer Coefficient
AdtthydtdAdkqd s
y
)( 0
0
−=⎟⎟⎠
⎞⎜⎜⎝
⎛=
=
( )0
0
000
0 )]/([
===⎥⎦
⎤⎢⎣
⎡=
−=
−−=
ηην dYd
xuk
ydtd
ttk
ydttttdkh
ysy
ss
xuyν
η 0=
1
001
0
)(2
exp CdfCd
Yd
yy
=⎟⎟
⎠
⎞
⎜⎜
⎝
⎛ηη−=
η=
η
=∫
Pr(22-7)
E. Pohlhausen
Supercritical Fluid Process Lab
(22-12)(22-11)
10 Cx
ukhx ν=
Local Heat Transfer Coefficient
Local heat transfer coefficient(function of x)
(22-13)
xx
x Ck
xhNu Re1=≡ (22-14)Nusselt number
Characteristic length
E. Pohlhausen
Supercritical Fluid Process Lab
Local Heat Transfer Coefficient
( )1
0 0
2/1 )(2PrexpRe
−∞
⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎟⎠
⎞⎜⎜⎝
⎛−= ∫ ∫ ηηη
η
ddfNu xx (22-15)
- valid for all Prandtl number- valid for Re < 5X105 (Laminar flow)
E. Pohlhausen
Supercritical Fluid Process Lab
Temperature for laminar flow past plate at uniform temperature
0tttt
s
s
−−
Supercritical Fluid Process Lab
0
1.00 2.0 3.0 4.0
1.0
0.5
( ) ( ) 3/12/1 PrRexxy⎟⎠⎞
⎜⎝⎛
Pr>0.6, the curves on Fig. 22-1 can be represented empirically by a single line relating the temperature variable (ts-t)/(ts-t0) to the quantity . ( ) ( ) 3/12/1 PrRexx
y⎟⎠⎞
⎜⎝⎛
Slope=0.332 This procedure is based on the equation found by Pohlhausen for the ratio of the thickness of the hydrodynamic boundary layer δ to the thickness of the thermal boundary layer δth.
For Pr > 0.6
3/1Pr=thδδ
( ) 3/12/1
0
0 Pr)(Re332.0)]/([x
y
ss
xydttttd
=−−
=
From Fig. 22-2
(22-17)
(22-16)
3/12/1 Pr)(Re332.0xx x
kh =
3/12/1 Pr)(Re332.0 xxNu =
(22-18)
(22-19)
E. Pohlhausen
Supercritical Fluid Process Lab
(21-6)[ ]
Pohlhausen found this equation
0
0 )/()(
=⎭⎬⎫
⎩⎨⎧ −−
=y
ss
dyttttdkh
Nux = Nusselt number @ point x
The effective mean coefficient: hm
∫ −=−=L
sxsm dxbtthttAhq0
00 )()(
∫=L
xm dxhL
h0
1
∫⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎠⎞
⎜⎝⎛=
Lp
xxd
kCu
Lk
02/1
3/12/10332.0 μν
3/12/10664.0
⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎠⎞
⎜⎝⎛=
kCLu
Lk pμ
ν
∫≡x
xm dxhx
h0
1
Supercritical Fluid Process Lab
kLh
Nu mm =
Width of the plate in the z-direction
0tts − is constant
( )2/13/12/1
0 2332.0 Lk
CuL
k p⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎠⎞
⎜⎝⎛=
μν
The mean effective heat-transfer coefficient: hm
3/12/1 Pr)(Re664.0 LmNu =
Lm hh 2=
- valid for all Prandtl number- valid for Re < 5 x 105
Supercritical Fluid Process Lab
kLh
Nu mm =
Num = average Nusselt number over a surface of length L
3/1Pr=thδδ
valid for Pr > 0.6 E. Pohlhausen
Supercritical Fluid Process Lab
Example 22-1
U0 U0
U0
Supercritical Fluid Process Lab
ftu
x 1.2Re0
==ν
72.0Pr))()(/(0164.0
/1021.0 23
==
×= −
FfthBtuksft
o
ν
ftux 0148.00.50
==νδ
sftu /500 =
ftth 0165.0Pr 3/1 ==δδ
))()(/(65.1Pr)(Re332.0 23/12/1 FfthBtux
kh oxx ==
))()(/(3.32 2 FfthBtuhh oxm ==
Heat transfer to a fluid entering a pipe
Le
u0t0
D
Le/D ~ 0.05 Re·Pr for laminar flowLe/D ~ 40-100 for turbulent flow
)20(66.3
)20(/PrRe62.13/1
3/13/1
<∞→=
≥⎟⎠⎞
⎜⎝⎛⋅=
∞ GzxforNu
GzLLforLDNu e
Gz이 작아지면 fully developed
Supercritical Fluid Process Lab
Heat transfer to a fluid entering a pipe
Le
u0t0
D
Le/D ~ 0.05 Re·Pr for laminar flowLe/D ~ 40-100 for turbulent flow
3/204.01065.066.3
GzGzNu
++=
Supercritical Fluid Process Lab
Graetz Problem
Graetz number:
DL
LDPe
LDGz
kxwC
Gz px
⋅=⋅⋅=
==
PrRe
convectionby fer heat transconductionby fer heat trans
Pe: Peclet numberconduction과 convection의 비교
Pe>100Convection >> Conduction
0),0(
),0(),(
=∂∂
==
xrtsymmetric
finitextxrtt
Supercritical Fluid Process Lab
Natural convectionNatural convection
Driving forces:
(1) Buoyancy Thermal convection
(2) Surface tension Marangoni convection
Supercritical Fluid Process Lab
Natural convection from a vertical plateNatural convection from a vertical plate
y, uy
x, ux
t∞, ρ∞
g
ux(y)
ts > t∞
Quiescentfluid
Pr < 1Pr < 1
thδδ
hot cold
x, ux
t∞, ρ∞
g
Quiescentfluid
cold hot
Supercritical Fluid Process Lab
Natural convection from a vertical plateNatural convection from a vertical plate
y, uy
x, ux
t∞, ρ∞
g
ux(y)ts > t∞
Quiescentfluid
2
2
2
2
)(
0
yt
ytu
xtu
yuttg
yuu
xuu
yu
xu
yx
xxy
xx
yx
∂∂
=∂∂
+∂∂
∂∂
+−=⎟⎟⎠
⎞⎜⎜⎝
⎛∂∂
+∂∂
=∂
∂+
∂∂
∞
α
μρβρ
Laminar flow
Continuity:
Momentum:
Energy:
Buoyancy forceBuoyancy force)](1[ 00 tt −−= βρρ
yexpansivitthermal:βSupercritical Fluid Process Lab
Natural convection heating of ideal diatomic adjacent to a vertical plate at constant temperature
number)(Reynoldsforceviscousforcebuoyant~
dragviscousforceinertial
forceviscousforcebuoyant~
uLu
LutgtLgGr
GrNum
⎟⎟⎠
⎞⎜⎜⎝
⎛
⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎟⎠
⎞⎜⎜⎝
⎛
⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎠⎞
⎜⎝⎛ Δ
=Δ
=
=
ννβ
νβ 2
22
3
4/1
/
)(478.0
CharacteristicVelocity, u
Supercritical Fluid Process Lab
∞−=Δ ttt s
gas idealfor 1~1TT
VV p
⎟⎠⎞
⎜⎝⎛∂∂
=β
TLttgGr s
2
3)(ν
∞−=(2-25)
convectionnaturalconvectionmixed
convectionforcedGrFF
LuforceinertiaF
LgforcebuoyancyF
i
b
i
b
1
32
22
3
10~
10Re
~)(
~)(
−
−
>
<=
Δ
ρ
ρ
Natural convection from a vertical plateNatural convection from a vertical plate
Re
2/1Gr
Forced convection
Naturalconvection
OMC(Opposing Mixed Convection)AMC(Assisting Mixed Convection)
Supercritical Fluid Process Lab
Rayleigh NumberRa <109 ; laminar flowRa >109 ; turbulent flow
( )[ ]
convectionforcedNu
GrxtgRa
convectionnaturalRaNu
xx
L
3/12/1
3
9/416/9
4/1
PrRe664.0
Pr
Pr/492.01
67.068.0
=
⋅=Δ
=
++=
ανβ
Natural convection from a vertical plateNatural convection from a vertical plate
Supercritical Fluid Process Lab
All Rayleigh Number
( )[ ] 27/816/9
6/1
Pr/492.01
387.0825.0+
+= LL
RaNu
Natural convection from a vertical plateNatural convection from a vertical plate
Supercritical Fluid Process Lab
Application: Benard Cell
Top view
Side view
Single cell
hot
cold
Bird view
Ra>1708; oneset of natural convection
-Surface tension-No slip condition
Supercritical Fluid Process Lab
Application: Natural convection from a vertical plateApplication: Natural convection from a vertical plate
-연기: 밀도차에 의한 퍼짐공기유입밀도차가 적어짐
Nu = a Grm Prn
Laminar flow
-TV set : 생성된 열이 자연대류에 의해dispersion
-열섬현상-아지랑이-열대야
-pipe 내의 온도차-자연대류 생성-Gr/Re2 <<1이면자연대류 무시가능
ColdCold
Hot
Supercritical Fluid Process Lab
Heat Transfer with a Developed Velocity Distribution in a Pipe
Local coefficient hx
Supercritical Fluid Process Lab
bpbsx dtwCttDdxh =−π ))((
dx
bt
st
What is the tb?
Graetz SolutionParabolic velocity profile
⎥⎥
⎦
⎤
⎢⎢
⎣
⎡⎟⎟⎠
⎞⎜⎜⎝
⎛−=
2
12i
bx rruu
Supercritical Fluid Process Lab
(22-26)
If the fluid is heated or cooled, the velocity profile can be greatly altered because of the effect of temperature on viscosity. The complications resulting in the heat transfer problems are so great that only approximate solutions have been obtained.
Graetz has provided solutions for two cases.
(1) No distortion assumption (parabolic velocity profile is maintained)(2) Great distortion assumption (plug flow, rodlike flow)
Influence of heating on velocity profile in laminar tube flow
Parabolic velocity profile
Supercritical Fluid Process Lab
If the fluid is heated or cooled, the velocity profile can be greatly altered because of the effect of temperature on viscosity.
heating
cooling
Liquid heatingGas cooling
Gas heatingLiquid cooling
μ↓
μ↑
Average velocity
Supercritical Fluid Process Lab
2
2111
1
max
020
2
02
uu
rdruR
rdrduR
dAuA
u
dAuA
u
b
R
x
R
xA
xb
Axb
=
===
=
∫∫∫∫∫
∫∫
ππ
θπ
π
Parabolic velocity profileParabolic velocity profile
The average velocity of the fluid at any axial position is found by summing up all the velocities over the cross section and dividing by the cross-sectional area
Graetz Solution
⎟⎟⎠
⎞⎜⎜⎝
⎛
∂∂
+∂∂
+∂∂
α=∂∂
2
2
2
2 1x
trt
rrt
xtux
Supercritical Fluid Process Lab
(22-27)⎥⎥
⎦
⎤
⎢⎢
⎣
⎡⎟⎟⎠
⎞⎜⎜⎝
⎛−=
2
12i
bx rruu
xt
rru
rt
rrt
i
b
∂∂
⎥⎥
⎦
⎤
⎢⎢
⎣
⎡⎟⎟⎠
⎞⎜⎜⎝
⎛−
α=
∂∂
+∂∂
2
2
21
21(22-28)
Axial fluid velocityat all points
0 Axial conduction negligible
PDE can be solved by separation variable
t=f(r)•g(x) PrRe/)/(2
00
in rxn
n
nn
s
s eBtttt β
∞=
=
φ=−− ∑ (22-29)
Parabolic velocity profileParabolic velocity profile
Details of Graetz solution are given by Drew.T.B. Drew, Trans. Am. Inst. Chem. Eng., 26, 26 (1931)
Graetz Solution
Supercritical Fluid Process Lab
⎥⎥
⎦
⎤
⎢⎢
⎣
⎡⎟⎟⎠
⎞⎜⎜⎝
⎛−=
2
12i
bx rruuPrRe/)/(2
00
in rxn
n
nn
s
s eBtttt β
∞=
=
φ=−− ∑
(22-30)
( )( )drrtuCCur
tirr
rxp
pbib πρ
ρπ= ∫
=
=21
02
rdrtuur
t irr
r xbi
b ∫=
==
02
2
Parabolic velocity profileParabolic velocity profile
The bulktemperatureof the fluidat any axialposition
Simplified form
Heat Transfer with a Developed Velocity Distribution in a PipeParabolic velocity profileParabolic velocity profile
xD
xD
kCDu
kxDCu
kxwC
Gz
ttdxdt
kwC
kDhNu
ttdxdt
DwC
h
pbpbp
bs
bpxx
bs
bpx
PrRe44
)4/(
11
2
⋅⎟⎠⎞
⎜⎝⎛=⎟
⎠⎞
⎜⎝⎛⎟⎠⎞
⎜⎝⎛===
−==
−=
ππμμ
ρπρ
ππ
Local coefficient hx
rdrtuur
t irr
r xbi
b ∫=
==
02
2
Supercritical Fluid Process Lab
dx
(22-31)
bpbsx dtwCttDdxh =−π ))((bt
st
Graetz SolutionFlat velocity profileFlat velocity profile
bx uu =
Supercritical Fluid Process Lab
an: the nth root of the expression J0(an)=0.J0: the zero order Bessel functionJ1: the first order Bessel function
xtu
rt
rrt b
∂∂
α=
∂∂
+∂∂ 1
2
2
(22-32)t=f(r)•g(x)
PDE can be solved By Separation variable
PrRe/)/(2
00
10
2
)(2
in rxan
n i
n
nns
s er
raJ
aJatttt −
∞=
=∑ ⎟⎟
⎠
⎞⎜⎜⎝
⎛=
−− (22-33)
Graetz Solution
Supercritical Fluid Process Lab
bx uu =
(22-34)
( )( )drrtuCCur
tirr
rxp
pbib πρ
ρπ= ∫
=
=21
02
drtrr
tirr
rib ∫
=
==
022
Flat velocity profileFlat velocity profile
PrRe/)/(2
00
10
2
)(2
in rxan
n i
n
nns
s er
raJ
aJatttt −
∞=
=∑ ⎟⎟
⎠
⎞⎜⎜⎝
⎛=
−−
Graetz SolutionFlat velocity profileFlat velocity profile
Supercritical Fluid Process Lab
∑
∑∞=
=
−−
∞=
=
−
= n
n
rxan
n
n
rxa
x
in
in
ea
e
kDh
1
PrRe/)/(22
1
PrRe/)/(2
2
2
(22-35)
bs
bpxx
bs
bpx
ttdxdt
kwC
kDh
Nu
ttdxdt
DwC
h
−π==
−π=
1
1(22-31)
drtrr
tirr
rib ∫
=
==
022
This analytical solution is shown graphically in Figure 22-3
Local Nusselt number for developed laminar flow in a pipe
PrRe4
⋅⎟⎠⎞
⎜⎝⎛⎟⎠⎞
⎜⎝⎛=
xDGz π
kDhNu x
x =
100
100101 10001
10
A: Rodlike flow, uniform heat fluxB: Rodlike flow, uniform wall temperatureC: Parabolic flow, uniform heat fluxD: Parabolic flow, uniform wall temperature
A: Rodlike flow, uniform heat fluxB: Rodlike flow, uniform wall temperatureC: Parabolic flow, uniform heat fluxD: Parabolic flow, uniform wall temperature
AABBCCDD
Supercritical Fluid Process Lab
Figure 22-3
Approachasymptoticvalues for long tube
Example 22-2: uniform heat flux in rod-like flowxxbxb tt
Δ+
⎜⎜⎜⎜⎜⎜⎜⎜⎜
⎝
⎛
−=−π
α==
∂∂
==∂∂
α=
∂∂
+∂∂
Δ+)())((
)(12
2
xbxxbpbsx
b
b
b
ttCwttdxDh
ua
xdtd
xt
constaaxtu
rt
rrt
Flow is rodlike
Nux=8 ?
bsb
p
bs
bpx ttu
aDCw
ttdxdt
DCw
h−
=−
=11 α
ππ
Supercritical Fluid Process Lab
If heat is added at a constant rate per unit
length of pipe, the temperature profile will
approach some constant shape at great distances from the pipe inlet. In this region, is constant.
xt
∂∂
x
(3)
(2)
(1)
kDhNu x
x =
bs
bpx ttdx
dtDCw
h−
=1
π
><><
≡x
xb u
tut
4
2Duw bπρ=since
( )bsbsbp
pbx tt
Dkattuc
aD
cDuh−
=−⎟⎟
⎠
⎞⎜⎜⎝
⎛=
41
4
2
ρα
ππρ
( )bs
xx tt
DakDhNu
−==
4
2
art
rrt
=∂∂
+∂∂ 1
2
2
21
2
ln4
crcart ++=
Example 22-2: uniform heat flux in rod-like flow
⎜⎜⎜
⎝
⎛
===
=∂∂
=
))((,2/
0,0
xttttDrrtr
sss
B.C.s
Supercritical Fluid Process Lab
(4)tb를 구하자!
Example 22-2: uniform heat flux in rod-like flow
stDrat +⎟⎟
⎠
⎞⎜⎜⎝
⎛−=
164
22
><><
≡x
xb u
tut ( )∫ +−==ri
stDadrrt
r 0
2
2 3221 π
π
( ) 8
324
4 2
22
=
⎟⎟⎠
⎞⎜⎜⎝
⎛=
−=
DaDa
ttDaNu
bsx
since
( ) ( )
irirrir
bsx
bsbs
ix
rart
rtktth
ttDa
tt
Dra
kDh
2)(
442 2
2
=∂∂
∂∂
−=−
−=
−
⎟⎠⎞
⎜⎝⎛
=
==
Supercritical Fluid Process Lab
f(x)이므로 t=f(r,x)
Average coefficients
It is convenient for design purposes to know the average heat-transfer coefficient for an entire length of pipe.
t0 tb2 :bulk temp at “2”
“2”
ts
absabss
a ttAhtttt
Ahq )(2
)()( 20 −=−+−
=
ha= arithmetic average coeff
∫ −=−=L
bsxabsa xdtthttLhbq
0
)()(
Supercritical Fluid Process Lab
(22-36)
(22-38)
LDAttCwq bp π=−= &)( 02
Average coefficients
( ) ( )20
022
bss
bpa
tttttt
Lkcw
kDh
−+−−
=π
sb tt
(22-37)
≅2for long cylinder and low flow rate,
GzLkcw
kDh pa
ππ22
== for rod-like/ parabolic
Supercritical Fluid Process Lab
rdrtuur
t irr
r xbi
b ∫=
==
02
2
GraphicalSolution
in Fig. 22-4
(22-39)Curve b and c
GraphicalSolution
in Fig. 22-4
Average Nusselt numberfor developed laminar flow in a pipe with uniform wall temperature
kDh
kDh
lm
o
100
10
1
0.11 10 100 1000 10000
PrRe4
⎟⎠⎞
⎜⎝⎛⎟⎠⎞
⎜⎝⎛==
LD
kLwC
Gz p π
Parabolic flowhlmD/k
Parabolic flowhaD/k
Rodlike flowhaD/k
Supercritical Fluid Process LabFigure 22-4
c
ba
Slope=1
Slope=1/3
lmbslm ttAhq )( −=
3/13/13/1
3/1
PrRe62.14
62.1 ⎟⎠⎞
⎜⎝⎛=⎟⎟
⎠
⎞⎜⎜⎝
⎛==
LD
Lkcw
kDhNu plm
π
14.03/13/13/1 PrRe86.1 ⎟⎟
⎠
⎞⎜⎜⎝
⎛⎟⎠⎞
⎜⎝⎛==
s
lmlm L
DkDhNu
μμ
for Gz > 20 , parabolic
for Gz > 20, parabolic Sieder and Tate equation
Average coefficients
4
2Duw bπρ=
Supercritical Fluid Process Lab
Wall temp
Homework
22-122-222-422-6
Supercritical Fluid Process Lab
내부 자연대류가 일어날 수 있는 구조
Supercritical Fluid Process Lab
이런 내부 구조에서의 자연 대류는 아래 그림과 같이 가열면 온도, TH와 상대적으로 온도가 낮은 면의 온도, TC의 차이 TH-TC를 기준 온도차이로 삼는다. 이를 사용해 평균열전달계수를 정의하거나, 유동 특성을구분하는 레일레이수에 적용시킨다. 즉, 평균열전달계수는
레일레이수는 특성길이를 가열면과 맞은편 면의 간격, L로 삼으면,
아래 그림과 같이 TH-TC의 크기가 어떤 기준을 넘지 못하면 유체는 정체되고 오직 전도에 의해서만 상, 하면사이의 열전달이 일어난다. 이 때 위의 열전달계수 정의식을 이용하게 되면, 전도열전달이q=k/L(TH-TC)임을 이용하면 이 된다.
Application: Benard Cell
Supercritical Fluid Process Lab
RaL>1708일 때 비로소 유동이 발생하게 되고, 아래 그림과 같이 셀모양의
유동이 생긴다. 점선과 실선은 회전방향이 반대인 셀로 시계방향과 반시계
방향 셀이 교대로 나타난다. 이렇게 되면 벽으로 향하는 유동이 있는 곳은
등온선이 조밀하게 되고, 벽에서 멀어지는 유동이 있는 곳은 등온선이 성
기게 나타나게 된다.
Application: Benard Cell
Supercritical Fluid Process Lab
좀 더 온도차이 TH-TC가 커지게 되면, 유동의 난동성분이 증가하여 아래 그
림과 같이 난류유동이 발생하게 된다. 이 경우 벽 근처에는 점성영향으로
등온선이 조밀하게 성층화되어 나타나지만 중심부는 활발한 유동의 혼합으
로 거의 비슷한 온도를 넓은 영역에서 가지게 된다.
Application: Benard Cell
Supercritical Fluid Process Lab
Natural convection in double pipe
Velocity field Temperature field
Supercritical Fluid Process Lab
수직 벽에서의 자연 대류
위의 그림은 가열된 수직 평판에서의 자연 대류에 의한 열경계층을 보여준다. 이러한 층류
형태의 열경계층은 오른쪽 그림에서와 같이 어느 이상의 거리를 진행하면 난류로 천이
(transition)하게 된다. 이러한 유동의 성질은 경계층 시작점으로부터 유동진행 거리를 특성
길이로 하는 레일레이수, Rax를 기준으로 나룰 수 있으며, 천이는 Rax~109에서 일어난다.
열전달계수, hc는 층류에서 급속히 감소하다가 천이점에서 다소 증가하게 되고, 이는 평판에
서의 강제 대류의 경우와 유사하다. 그러나 난류에 접어들면서 열전달계수는 거의 일정하게
유지되는 특징을 보인다. Supercritical Fluid Process Lab
수평 실린더 주변에서의 자연 대류
위 가열 실린더 주변에서의 열경계층 그림에서와 같이 데워진 유체는 실린더 표
면을 따라 상승하게 되고, 최상부에서 만나 대칭을 이루며 발달하게 된다. 강제
대류의 경우보다 열경계층은 다소 두껍게 형성된다. 특성길이를 실린더 직경, D
로 삼는 레일레이수, RaD가 RaD≤109인 경우에 층류 유동이 형성되며, 열전달계
수는 RaD에 비례하여 커진다. 난류로의 천이가 일어나는 RaD≥109에서는 RaD의
증가에 따른 열전달계수의 증가가 더 커지게 된다.
Re=0
Supercritical Fluid Process Lab
강제 대류를 말할 때 보통 밀도차에 의한 부력의 영향은 무시하는 경우가 많다. 그러나 대류
열전달은 표면 주의 유체의 가열 혹은 냉각을 수반하게 되고 이것은 때에 따라 중요하게 고려
되어야 하는 부력을 발생시키게 된다. 강제 대류를 일으키는 유동이 충분히 강하지 못해 위와
같은 자연 대류를 함께 고려해야 하는 경우를 혼합 대류라 한다.
부력의 방향은 강제 대류 성분을 때에 따라 강화 혹은 약화시키게 되는데, 예를 들어 위의
그림의 왼쪽과 같이 부력의 방향이 위를 향할 때 바람이 아래에서 위로 분다면 대류열전달은
더욱 활발해 질 것이다. 반면 아래 오른쪽 그림과 같이 부력의 방향이 바람의 방향과
반대여서 강제 대류를 방해하게 되면 대류열전달이 감소할 것이다.
혼합 대류 (mixed convection)
Supercritical Fluid Process Lab
구나 실린더의 경우에도 아래 그림과 같이 조용한 공기 안에서의 자연 대류와 바람
에 의한 강제 대류가 첨가되는 경우는 그 열경계층 및 국소/평균 열전달계수의 분포
가 변화하게 된다.
혼합 대류 (mixed convection)
Supercritical Fluid Process Lab
레이놀즈수가 매우 작아 Re=23인 경우 등온선은 부력의 지배적인 영향으
로 오른쪽 상단으로 치솟아 올라가고 있지만, Re=120으로 속도가 증가한
경우 다소 상하 비대칭적인 등온선 분포를 나타내긴 하지만 대체로 강제
대류의 영향권 안에 있음을 볼 수 있다
혼합 대류 (mixed convection)레이놀즈수에 따른 가열실린더의 대류 특성
Supercritical Fluid Process Lab
실린더 주변의 유동은 점성유체역학에 나타나 있듯이 레이놀즈
수에 따라 그 유동양상이 달라지게 되고, 이는 열전달에도 같은
영향을 미친다. 위 그림은 가열된 실린더 주변의 등온선을 보여
주고 있는데, 가열된 유체의 밀도차이로 인해 상하 대칭이 약간
일그러짐을 알 수 있다.
가열된 실린더 주위에서의 등온선
Supercritical Fluid Process Lab
혼합 대류와 강제 대류/자연 대류의 구분은 유동장의 분류하는 강제
대류의 레이놀즈수와 자연 대류의 그라숍수의 조합으로부터 얻어진다.
혼합 대류 (mixed convection)
Supercritical Fluid Process Lab
생활생활 속의속의 대류열전달대류열전달
1. 강제 대류 - 선풍기와 에어컨
유동에 의한 대류 효과는 그것이 없을 때에 비해, 열전달에 있어 너무도
뚜렷한 차이를 보이기 때문에 생활 속에서도 자주 접할 수 있다. 가장
대표적인 예가 선풍기이다. 여름에 더운 날 선풍기를 튼다고 해서 방안의
공기 온도가 낮아지는 것은 전혀 아닌데도 시원한 것은 강제 대류에 의해
사람의 피부와 공기와의 열전달계수가 높아졌기 때문이다. 그러나 이러한
선풍기도 주변 공기 온도가 피부의 표면온도보다 낮은 경우에만 효과가 있다.
즉, 사막과 같이 40도를 웃도는 공기온도에서 선풍기를 튼다면, 혹은 한증막
안에서 선풍기를 튼다면, 열전달계수만을 높이는 선풍기는 주변의 뜨거운
열기를 피부로 빠르게 침투시켜, 그 안의 사람을 고문할 뿐이다.
Supercritical Fluid Process Lab
생활생활 속의속의 대류열전달대류열전달
에어컨과 선풍기를 동시에 사용하면 에너지 절약효과가 있다는 것을 대류열전
달의 기본 관계식인 뉴톤의 냉각법칙(Newton's cooling law)을 이용해서 고찰
해보자.
qs = hc△T (열전달율 = 대류열전달계수×온도차)
냉방효과를 높이는 것은 피부에서 공기로의 qs를 높이는 것을 의미한다. 위
식에서 볼 수 있듯이 이것은 피부와 공기의 온도차를 크게 하고,
대류열전달계수를 높이는 것으로 달성할 수 있다. 에어컨을 조금 약하게
사용하여 온도차의 벌어짐이 조금 적어지더라도, 선풍기의 도움으로
열전달계수가 좀 더 높아진다면, 에어컨만으로 온도차를 크게 벌려 얻어지는
qs를 충분히 얻을 수 있을 것이다.
Supercritical Fluid Process Lab
이런 간단하고 근본적인 열전달 관계식을 좀더 에어컨에 이용하는 방법은 없을까? 에어컨
은 기계적 일을 가함으로써 자연스러운 열전달을 거슬러 찬 곳에서 더운 곳으로 열전달을
시키는 시스템이다. 방안에 냉기를 불어넣어 주듯이 에어컨은 실외기를 통해 열을 방출해
야 한다. 실외기의 표면온도는 외부의 공기 온도보다 높게 조절된다. 그래야만 열을 방출
할 수 있기 때문이다. 이를 돕기 위해 실외기에는 보통 팬이 설치되어 있어 인위적으로 바
람을 불어 넣어 준다. 즉, 강제 대류를 일으켜 열전달계수를 높이려는 조작이다. 이 팬의
속도나 효율은 이미 정해져 있는 것이므로 위 뉴톤의 냉각법칙에서 우리는 대류열전달계
수를 변화시킬 수 없다. 그렇다면 온도차, 즉 실외기 표면과 외부 공기와의 온도차는 어떠
한가? 장소를 선택할 수 있다면 그늘진 곳을, 방향은 북향을 찾아 실외기를 설치한다면 어
느 정도는 온도차를 크게 할 수 있다. 여름철의 그늘과 양지의 온도차이는 누구나 알 정도
로 확연하다.
생활생활 속의속의 대류열전달대류열전달
Supercritical Fluid Process Lab
생활생활 속의속의 대류열전달대류열전달
대류열전달을 이용한 실제 시스템에서는 대부분 위에서 설명한 관내유동이나 평
판이나 실린더 주변에서의 유동의 복합적인 형태의 적용이 요구된다. 아래 쉘-튜
브형 열교환기의 예에 있어서, 많은 파이프를 지나는 내부 유동 대류열전달과 실
린더 다발을 지나는 외부 유동 대류열전달이 적용된다. 이와 같이 기본적인 형상
에서의 대류열전달 및 마찰손실에 대한 지식은 실제 열전달 시스템 해석과 새로운
시스템의 개발에 유용하게 사용된다.
Shell and Tube Heat ExchangerSupercritical Fluid Process Lab
생활생활 속의속의 대류열전달대류열전달
2. 그 외의 강제 대류 - 겨울 바람과 목욕탕 등
자연풍이든 선풍기 바람이든 여름철엔 고마운 강제 대류 현상이 겨울에는
반대가 되는 것도 같은 이유임을 이 쯤에서 누구나 알 수 있을 것이다.
겨울에 살을 에이는 듯한 바람도 역시 열전달계수를 높이기 때문이다.
여기서 한 걸음 더 나아가 본다면, 겨울 바람 속의 몸을 움추린 사람은 강제
대류의 외부 유동에 설명되어 있는 실린더 주변에서의 유동과 다름이 아니다.
실린더 주변에서의 열전달계수는 바람이 처음으로 부딪히는 실린더의 맨
앞쪽, 즉 정체점(stagnation point)에서 가장 크다. 그러므로 우리는 바람을
정면으로 맞는 것보다는 조금이라도 빗겨서 맞아야 추위를 덜 느낄 수 있다.
Supercritical Fluid Process Lab
생활생활 속의속의 대류열전달대류열전달
공중 목욕탕에 가본 사람이라면 뜨거움을 참으며 겨울 온탕에 몸을 담갔다
가, 다른 사람이 들어오는 바람에 물이 출렁여 물이 더욱 뜨겁게 느껴졌던
경험이 있을 것이다. 이제 우리는 이에 대한 이유를 알뿐만 아니라, 한증탕
에 들어가 체조까지 하는 사람들을 좀 더 경이롭게 쳐다보게 될 것이다. 유
체 자체의 움직임뿐만 아니라 우리 몸의 움직임에 의한 유체의 상대적 운
동도 역시 강제 대류를 일으키기 때문이다. 이런 것을 겨울철 캔 커피 난로
(?)에 이용해 보면 어떨까. 추운 날 따뜻한 캔 커피는 마시기 전 충분히 주
머니 난로만큼의 역할을 하곤 한다. 그런데 강풍으로 이내 미지근해져 버
린 캔 커피는 흔들어 주면 그럭저럭 두세 번 손을 따뜻하게 해주는데 사용
할 수 있게 된다.
Supercritical Fluid Process Lab
3. 자연 대류 - 냉난방 방향
뜨거운 공기는 가벼워 위로 올라가고 차가운 공기는 무거워 아래로
내려온다는 것으로 많은 판단을 할 수가 있다. 에어컨은 사람들이
더워 찬바람을 쏘이기 위해 바람의 방향을 아래로 해 놓는 경우가
많은데, 이것은 밖에서 땀 흘리고 들어온 사람에게 도움이 될
뿐이다. 평상시의 냉방은 바람을 위로 향하게 하는 것이 좋다.
그러면 방 위쪽의 더운 공기를 식히고 자연스럽게 무거운 찬 공기는
아래로 내려오게 된다. 그러나 만약 아래로 냉방 바람을 계속
내보내면 방 위쪽의 더운 공기는 그대로 남아 방안의 공기는 아래는
차고 위는 덥게 성층화(成層化)될 것이다. (계속)
생활생활 속의속의 대류열전달대류열전달
Supercritical Fluid Process Lab
그렇다면 난방 바람은 당연히 아래를 향해야 할 것이다. 그럼 아래
로 내보내진 더운 바람은 자연 대류로 방 위쪽으로 올라가 순환하
게 될 것이다. 이런 것을 생각하면 자동차 안의 에어컨이나 히터의
배출 조정은 항상 현명하게 할 수 있을 것이다. 전술한 이유로 중
앙 냉난방 식의 경우 보통 에어컨은 천장에서 분출되고 라지에타
는 아래에 설치되는 것이다. 종종 식당이나 카페는 1, 2층이 트여
있는 곳이 있는데, 꽤 넓어 층별 냉난방을 하는 곳이 아니라면 보
통 한 개의 냉난방기를 사용하게 된다. 이렇게 되면 층간의 온도차
이는 반드시 나기 마련이다. 이런 곳에서는 당연히 겨울에는 2층에,
여름에는 1층에 자리를 잡는 것이 현명한 선택이다.
생활생활 속의속의 대류열전달대류열전달
Supercritical Fluid Process Lab
실린더 주위에서의 열전달계수 분포
왼편 그림은 실린더 표면에서의 열전달계수
를 원주방향에 따라 나타낸 것으로 θ=0°가
실린더의 맨 왼쪽을, θ=180°가 실린더의 맨
오 른 쪽 을 나 타 낸 다 . 경 계 층 의 박 리
(separation)가 θ∼80°에서 일어나는 층류
경계층의 경우 박리 전에 열전달계수가 지속
적으로 감소하다가 박리 이후 난동성분의 증
가로 다소 증가하게 된다. 그러나 난류로의
천이가 일어나는 오른쪽 그림의 경우 천이로
인한 급속한 열전달계수 증가가 나타난다. 이
는 평판 위를 지나는 유동의 경우에서도 나타
났던 것이다. 그 이후 경계층의 박리에 의해
열전달계수는 다시 급속히 감소하게 된다.
Supercritical Fluid Process Lab
top related