phy210 ch5
Post on 06-Apr-2018
230 Views
Preview:
TRANSCRIPT
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 1/42
Chapter 5
GAS LAWS AND
KINETIC THEORY
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 2/42
Boyles‟, Charles and Gay-Lussacs‟ Law
GAS LAW
Gases are a state of matter characterized bytwo properties which are lack of exact volumeand lack of exact shape.
There are three properties of gases: Volume, V Pressure, P Temperature, T
2
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 3/42
The Gas Laws and Absolute Temperature
The relationship between the volume,pressure, temperature, and mass of a gas iscalled an equation of state.
The gases law that we will cover for thischapter including: Boyle`s law
Charles`s law Pressure law or Gay-Lussac law
3
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 4/42
BOYLE‟S LAW
The volume of a gas depends on the pressure exerted onit. When you pump up a bicycle tire, you push down on ahandle that squeezes the gas inside the pump. You cansqueeze a balloon and reduce its size (the volume itoccupies).
In general, the greater the pressure exerted on a gas,the less its volume and vice versa.
This relationship is true only if the temperature of thegas remains constant while the pressure is changed.
4
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 5/42
Pressure is
inversely proportionalto the volume.
5
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 6/42
Boyle‟s law definition:
..’The volume of a given
amount of gas is inversely proportional to the absolute
pressure as long as thetemperature is constant ’..
We can see that the data fit into apattern called a hyperbola.
6
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 7/42
If, however weplot pressure against 1/volumewe get a linear (straight line)graph.
PV = constant
Thus;
P1V1 = P2V2
7
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 8/42
• Charles‟s law definition:
..’ the volume of a givenamount of gas is directly
proportional to the absolutetemperature (Kelvin) when the
pressure is kept constant ’..
Charles‟s law
8
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 9/42
V/T = constant
Thus;
V1 /T1 = V2 /T2
• By extrapolating, the volume becomes zero at−273.15°C; this temperature is called absolute
zero (refer figure).
• Therefore, absolute temperature:
T(K) = T(C) + 273.15
9
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 10/42
• Definition:
..’The absolute pressure of a given amount of gas is
directly proportional to the absolute temperature (K)when the volume is kept constant ’..
P/T = constant
Thus; P1 /T1 = P2 /T2
Gay-Lussacs‟ law
10
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 11/42
Absolute Temperature andIdeal Gas Law
Absolute Temperature
Known as the Kelvin scale. Degrees are samesize as Celcius scale.
Absolute zero = 0°C = 273.15 K
11
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 12/42
At standard atmospheric pressure :
Room temperature is about 293 K (20°C)
Standard temperature is 273 K
Water freezes at 273.15 K and boils at 373.15 K.
T (K) = T (°C) + 273.15
12
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 13/42
Note:If any gas could be cooled to -273°C, the volume would
be zero.
13
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 14/42
• This three gas laws can be combined to produced a singlemore general relation between absolute pressure, volumeand absolute temperature; that is:
Where PV/T = constant
Thus;
P1V1 /T1 = P2V2 /T2
The Ideal Gas Law
14
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 15/42
• Now we are looking to a simple experiment where theballoon is blown up at a constant pressure and temperature(figure below).
• It is found that, the volume, V of a gas increases in directproportion to the mass, m of a gas present:
V m
Hence we can write:
15
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 16/42
• A mole (mol) is defined as the number of grams of asubstance that is numerically equal to the molecular mass of the substance.
Example:
i. 1 mol H2 has a mass of 2 g.
ii. 1 mol Ne has a mass of 20 g.
iii. 1 mol CO2 has a mass of 44 g; where the molecularmass for CO2 = [12 + (2 x 16)] = 44 g/mol
16
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 17/42
• Where the number of moles in a certain mass of materialis given as:
17
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 18/42
18
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 19/42
• From proportion the equation for ideal gaslaw can be written as:
• Where n is the number of moles and R is the universal gasconstant and its value is given as:
19
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 20/42
• The ideal gas law often refers to “standard conditions” orstandard temperature and pressure (STP). Where at STP:
T = 273 K
P = 1.00 atm
= 1.013 x 105 N/m2
= 101.3 kPa
20
Note:1 mol STP gas has:i. Volume = 22.4Lii. No. of molecule/moles = 6.023 x 1023 molecules
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 21/42
Note:
When using and dealing with all this three gas laws and alsoideal gas law; the temperature must in Kelvin (K) and the
pressure must always be absolute pressure, not gaugepressure.
Absolute pressure = gauge pressure + atmospheric pressure
21
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 22/42
1. Determine the volume of 1.00 mol of any gas, assumingit behaves like an ideal gas, at STP.
(ans: 0.0224 m3)
2. An automobile tire is filled to a gauge pressure of 200kPa at 10°C. After a drive of 100 km, the temperaturewithin the tire rises to 40°C. What is the pressure withinthe tire now?
(ans: 333 kPa)
Exercises:
22
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 23/42
• Since the gas constant is universal, the number of moleculesin one mole is the same for all gases. That number is calledAvogadro‟s number:
• The number of molecules in a gas is the number of molestimes Avogadro‟s number:
Ideal Gas Law in Terms of Molecules:Avogadro‟s Number
23
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 24/42
Therefore we can write:
Where k is called Boltzmann‟s constant
24
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 25/42
Kinetic Theory and the MolecularInterpretation of Temperature
The force exerted on the wall by the collision of onemolecule is:
Then the force due to all molecules colliding with thatwall is:
25
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 26/42
Figure 13.16:(a)Molecules of a gas moving about
in a rectangular container.
(a) Arrows indicate the momentumof one molecules as it reboundsfrom the end wall.
26
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 27/42
The averages of the squares of the speeds in all threedirections are equal:
So the pressure is:
27
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 28/42
Rewriting;
So;
28
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 29/42
The average translational kinetic energy of themolecules in an ideal gas is directly proportional to thetemperature of the gas.
29
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 30/42
We can invert this to find the average speed of molecules in a gas as a function of temperature:
30
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 31/42
Distribution of Molecular Speeds
These two graphs show the distribution of speeds of molecules in a gas, as derived by Maxwell. The mostprobable speed, v P, is not quite the same as the rmsspeed.
Note:vrms is not at the peak of the curve because the curve is skewed to the right (not symmetrical).vp is called the „most probable speed.
Figure 13.17: Distribution of speeds of molecules in an ideal gas.
31
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 32/42
As expected, the curves shift to the right with temperature.
Figure 13.18: Distribution of molecular speeds for two different temperature
32
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 33/42
• The ideal gas law equation is given as;
• The term of “ideal” refers to characteristics/behavior of gaswhere at “ideal”, the pressure of gas is too high and thetemperature of gas close/near the liquefaction point (boilingpoint).
Real Gases
33
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 34/42
• However, at pressures less than an atmosphere or so (nottoo high), and when temperature is not close to the boilingpoint of the gas, it is refers to behavior of real gases.
• Figure below is the curve of P vs V at temperatureconstant for ideal gas (Boyle`s law).
34
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 35/42
• And figure below is the curves represent the behavior of thegas at different temperatures (not constant) for real gases.Where TA TB TC TD
• It is found that, the cooler (temperature decrease @ fartherfrom boiling point) it gets, the further the gas is from ideal.
35
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 36/42
Below the critical temperature (the gas can liquefy if thepressure is sufficient; above it, no amount of pressurewill suffice):
36
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 37/42
• The dashed curve A` and B`represents the behavior of a gas aspredicted by the ideal gas law (Boyle`slaw) for several different values of the
temperature.• We see that, the behavior of gasdeviates even more from the curvespredicted by ideal gas law (curves Aand B), and the deviation is greater
when the gas is closer to liquid-vaporregion (curve C and D).
Figure 13.19: PV diagram forreal substance
37
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 38/42
• In curve D, the gas becomes liquid; it begins condensingat (b) and is entirely liquid at (a).
• Curve C represent the behavior of the substance at its
critical temperature, and the point (c) is called the criticalpoint.
• At temperature less than the critical temperature, a gaswill change to the liquid phase if sufficient pressure isapplied.
38
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 39/42
• The behavior of a substance can be diagrammed not onlyon a PV diagram but also on a PT diagram.
• A PT diagram is called a phase diagram; it shows allthree phases of matter:
i. The solid-liquid transition (in equilibrium) is meltingor freezing
ii. The liquid-vapor transition is boiling or condensing
iii. The solid-vapor transition is sublimation. Wheresublimation refers to the process whereby at lowpressures a solid changes directly into the vaporphase without passing through the liquid phase.
39
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 40/42
• The intersection of the three curves is called the triplepoint. Where it is only at triple point that the three phasescan exist together in equilibrium.
Figure 13.20: Phase diagram of water.
40
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 41/42
Figure 13.21: Phase diagram of carbon dioxide.
41
8/3/2019 PHY210 Ch5
http://slidepdf.com/reader/full/phy210-ch5 42/42
top related