digital system ch4-1 chapter 4 combinational logic ping-liang lai ( 賴秉樑 ) digital system...

Digital System Ch4-1

Chapter 4 Combinational Logic

Ping-Liang Lai (賴秉樑 )

Digital System數位系統


Outline of Chapter 4

4.1 Introduction 4.2 Combination Circuits 4.3 Analysis Procedure 4.4 Design Procedure 4.5 Binary Adder-Subtractor 4.6 Decimal Adder 4.7 Binary Multiplier 4.8 Magnitude Comparator 4.9 Decoders 4.10 Encoders 4.11 Multiplexers 4.12 HDL Models of Combination Circuits


4.1 Introduction (p.138)

Logic circuits for digital systems may be combinational or sequential.

A combinational circuit consists of logic gates whose outputs at any time are determined from only the present combination of inputs.


4.2 Combinational Circuits (p.138)

Logic circuits for digital system Sequential circuits

» Contain memory elements.» The outputs are a function of the current inputs and the state of the memory

elements.» The outputs also depend on past inputs.


Combinational Circuits (p.139)

A combinational circuits 2

n possible combinations of input values

Specific functions» Adders, subtractors, comparators, decoders, encoders, and multiplexers.» MSI circuits or standard cells.

CombinationalLogic Circuit

n inputvariables

m outputvariables

….. …..Figure 4.1 Block diagram of combinational circuit


4-3 Analysis Procedure (p.139)

A combinational circuit Make sure that it is combinational not sequential

» No feedback path. Derive its Boolean functions (truth table) Design verification A verbal explanation of its function


A Straight-forward Procedure (p.140)

F2 = AB+AC+BCT1 = A+B+CT2 = ABCT3 = F2'T1

F1 = T3+T2

Figure 4.2 Logic Diagram for Analysis Example


F1 = T3+T2 = F2'T1+ABC = (AB + AC + BC)'(A + B + C) + ABC = (A' + B')(A' + C')(B' + C')(A + B + C) + ABC = (A' + B'C') (AB' + AC' + BC' + B'C) + ABC = A'BC' + A'B'C + AB'C' + ABC

A full-adder F1: the sum

F2: the carry


The Full-adder

The truth table


4-4 Design Procedure (p.142)

The design procedure of combinational circuits State the problem (system spec.) Determine the inputs and outputs The input and output variables are assigned symbols Derive the truth table Derive the simplified Boolean functions Draw the logic diagram and verify the correctness


Design Procedure

Functional description Boolean function HDL (Hardware description language)

» Verilog HDL» VHDL

Schematic entry Logic minimization

Number of gates Number of inputs to a gate Propagation delay Number of interconnection Limitations of the driving capabilities


Code Conversion Example (p.143)

BCD to excess-3 code The truth table


The Maps (p.144)

Figure 4.3 Maps for BCE to Excess-3 Code Converter


(p.145)

The simplified functions z = D' y = CD +C'D' x = B'C + B'D+BC'D' w = A+BC+BD

Another implementation z = D' y = CD +C'D' = CD + (C+D)' x = B'C + B'D+BC'D' = B'(C+D) +B(C+D)' w = A+BC+BD


BCD to Excess-3

The logic diagram

Fig. 4-4 Logic Diagram for BCD to Excess-3 Code Converter

z = D' y = CD +C'D' = CD + (C+D)' x = B'C + B'D+BC'D' = B'(C+D) +B(C+D)‘w = A+BC+BD


4-5 Binary Adder-Subtractor (p.146)

Half adder 0 + 0 = 0 ; 0 + 1 = 1 ; 1 + 0 = 1 ; 1 + 1 = 10 Two input variables: x, y Two output variables: C (carry), S (sum) Truth table


Half Adder

S = x'y+xy' C = xy

The flexibility for implementation S = xy S = (x+y)(x'+y') S' = xy+x'y' S = (C+x'y')' C = xy = (x'+y')'

Digital System Ch4-18Figure 4.5 Implementation of Half-Adder


Full-Adder (p.147)

Full-Adder The arithmetic sum of three input

bits. Three input bits

» x, y: two significant bits.» z: the carry bit from the previous

lower significant bit. Two output bits: C, S

Digital System Ch4-20Fig. 4-7 Implementation of Full Adder in Sum of Products

Fig. 4-6 Map for Full Adder

Full-Adder

S C


Full-Adder

S = x'y'z+x'yz'+ xy'z'+xyz C = xy+xz+yz S = z(xy) = z'(xy'+x'y)+z(xy'+x'y)'= z'xy'+z'x'y+z((x'+y)(x+y')) =

xy'z'+x'yz'+xyz+x'y'z C = z(xy'+x'y)+xy = xy'z+x'yz+ xy

Fig. 4-8 Implementation of Full Adder with Two Half Adders and an OR Gate


Binary Adder (p.149)

Figure 4.9 Full-bit adder


Carry propagation

When the correct outputs are available The critical path counts (the worst case) (A1, B1, C1) → C2 → C3 → C4 → (C5, S4) When 4-bits full-adder → 8 gate levels (n-bits: 2n gate levels)

Figure 4.10 Full Adder with P and G Shown


Parallel Adders

Reduce the carry propagation delay Employ faster gates Look-ahead carry (more complex mechanism, yet faster) Carry propagate: Pi = AiBi

Carry generate: Gi = AiBi

Sum: Si = PiCi

Carry: Ci+1 = Gi+PiCi

C0 = Input carry

C1 = G0+P0C0

C2 = G1+P1C1 = G1+P1(G0+P0C0) = G1+P1G0+P1P0C0

C3 = G2+P2C2 = G2+P2G1+P2P1G0+ P2P1P0C0


Carry Look-ahead Adder (1/2)

Logic diagram

Fig. 4.11 Logic Diagram of Carry Look-ahead Generator


Carry Look-ahead Adder (2/2)

4-bit carry-look ahead adder Propagation delay of C3, C2

and C1 are equal.

Fig. 4.12 4-Bit Adder with Carry Look-ahead


Binary Subtractor

A － B = A+(2’s complement of B) 4-bit Adder-subtractor

M=0, A+B; M=1, A+(B’+1)

Fig. 4.13 4-Bit Adder Subtractor


Overflow The storage is limited Add two positive numbers and obtain a negative number Add two negative numbers and obtain a positive number V = 0, no overflow; V = 1, overflow

Example:


4-6 Decimal Adder

Add two BCD's 9 inputs: two BCD's and one carry-in 5 outputs: one BCD and one carry-out

Design approaches A truth table with 29 entries Use binary full Adders

» The maximum sum ← 9 + 9 + 1 = 19» Binary to BCD


BCD Adder (1/3)

BCD Adder: The truth table


BCD Adder (2/3)

Modifications are needed if the sum > 9 If C = 1, then sum > 9

» K = 1, or

» Z8Z4 = 1 (11××), or

» Z8Z2 = 1 (1×1×).

Modification: (10)d or + 6

C = K +Z8Z4 + Z8Z2


BCD Adder (3/3)

Block diagram

Fig. 4-14 Block Diagram of a BCD Adder


Binary Multiplier (1/2)

Partial products AND operations

Fig. 4.15 Two-bit by two-bit binary multiplier


Binary Multiplier (2/2)

4-bit by 3-bit binary multiplier

Fig. 4.16 Four-bit by three-bit binary multiplier


4-8 Magnitude Comparator

The comparison of two numbers Outputs: A>B, A=B, A<B

Design Approaches The truth table of 2n-bit comparator

» 22n

entries - too cumbersome for large n Use inherent regularity of the problem

» Reduce design efforts» Reduce human errors


Algorithm → logic A = A3A2A1A0 ; B = B3B2B1B0

A=B if A3=B3, A2=B2, A1=B1 and A1=B1

» Equality: xi= AiBi+Ai'Bi'

» (A=B) = x3x2x1x0=1

(A>B) = A3B3'+x3A2B2'+x3x2A1B1'+x3x2x1 A0B0'

(A<B) = A3'B3+x3A2'B2+x3x2A1'B1+x3x2x1 A0'B0

Implementation xi = (AiBi'+Ai'Bi)'

Digital System Ch4-37Fig. 4.17 Four-bit magnitude comparator.


4-9 Decoder

A n-to-m decoder A binary code of n bits = 2

n distinct information

N input variables; up to 2n output lines

Only one output can be active (high) at any time


An implementation

Fig. 4.18 Three-to-eight-line decoder


Combinational logic implementation Each output = a minterm. Use a decoder and an external OR gate to implement any Boolean function

of n input variables.


Demultiplexers A decoder with an enable input. Receive information on a single line and transmits it on one of 2

n possible

output lines.

Fig. 4.19 Two-to-four-line decoder with enable input


Decoder/demultiplexers

第三版內容，參考用 !


Expansion Two 3-to-8 decoder: a 4-to-16 decoder

Fig. 4.20 4 16 decoder constructed with two 3 8 decoders


Combination Logic Implementation

Each output = a minterm Use a decoder and an external OR gate to implement any Boolean function

of n input variables A full-adder

» S(x, y, z) = (1,2,4,7)» C(x, y, z) = (3,5,6,7)

Fig. 4.21 Implementation of a full adder with a decoder


Two possible approaches using decoder» OR(minterms of F): k inputs (k minterms)

» NOR(minterms of F'): 2n k inputs

In general, it is not a practical implementation


4-10 Encoders

The inverse function of a decoder

1 3 5 7

2 3 6 7

4 5 6 7

z D D D D

y D D D D

x D D D D

The encoder can be implemented with three OR gates.


An implementation

Limitations » Illegal input: e.g. D3=D6=1» The output = 111 (¹3 and ¹6)

第三版內容，參考用 !


Priority Encoder

Resolve the ambiguity of illegal inputs Only one of the input is encoded

D3 has the highest priority D0 has the lowest priority X: don't-care conditions V: valid output indicator


The maps for simplifying outputs x and y

Fig. 4.22 Maps for a priority encoder


Implementation of priority

Fig. 4.23 Four-input priority encoder2 3

3 1 2

0 1 2 3

x D D

y D D D

V D D D D


4-11 Multiplexers

Select binary information from one of many input lines and direct it to a single output line

2n input lines, n selection lines and one output line

e.g.: 2-to-1-line multiplexer

Fig. 4.24 Two-to-one-line multiplexer


4-to-1 line multiplexer

Fig. 4.25 Four-to-one-line multiplexer


Note: 2n-to-1 multiplexer n-to- 2

n decoder

Add the 2n input lines to each AND gate

OR (all AND gates) n selection lines An enable input (an option)

Digital System Ch4-54Fig. 4.26 Quadruple two-to-one-line multiplexer


Boolean Function Implementation

MUX: a decoder + an OR gate 2

n-to-1 MUX can implement any Boolean function of n input variable

A better solution: implement any Boolean function of n+1 input variable» n of these variables: the selection lines» The remaining variable: the inputs


An example: F(A, B, C) = (1, 2, 6, 7)

Fig. 4.27 Implementing a Boolean function with a multiplexer


Procedure: Assign an ordering sequence of the input variable The rightmost variable (D) will be used for the input lines Assign the remaining n-1 variables to the selection lines w.r.t. their

corresponding sequence Construct the truth table Consider a pair of consecutive minterms starting from m0

Determine the input lines


Example: F(A, B, C, D) = (1, 3, 4, 11, 12, 13, 14, 15)

Fig. 4.28 Implementing a four-input function with a multiplexer


Three-state Gates

A multiplexer can be constructed with three-state gates Output state: 0, 1, and high-impedance (open ckts)

Fig. 4.29 Graphic symbol for a three-state buffer


Example: Four-to-one-line multiplexer

Fig. 4.30 Multiplexer with three-state gates


4-12 HDL Models of Combinational Circuits

Modeling Styles Gate-level modeling using instantiations of predefined and user-defined

primitive gates. Dataflow modeling using continuous assignment statements with the

keyword assign. Behavioral modeling using procedural assignment statements with the

keyword always.


Gate-level Modeling

The four-valued logic truth tables for the and, or, xor, and not primitives


Gate-level Modeling

Example:

The first statement declares an output vector D with four bits, 0 through 3.

The second declares a wire vector SUM with eight bits numbered 7 through 0.

output [0: 3] D;wire [7: 0] SUM;


HDL Example 4-1

Two-to-one-line decoder


HDL Example 4-2

Four-bit adder: bottom-up hierarchical description


HDL Example 4-2 (continued)


Three-State Gates

Statement: gate name (output, input, control);

Fig. 4.31 Three-state gates


Three-State Gates

Examples of gate instantiation

Fig. 4.32 Two-to-one-line multiplexer with three-state buffers


Dataflow Modeling

Verilog HDL operators

Example:

assign Y = (A & S) | (B & ~S)


HDL Example 4.3

Dataflow description of a 2-to-4-line decoder


HDL Example 4-4

Dataflow description of 4-bit adder


HDL Example 4-5

Dataflow description of 4-bit magnitude comparator


HDL Example 4-6

Dataflow description of a 2-to-1-line multiplexer

Conditional operator (?:)

Condition ? True-expression : false-expression

Example: continuous assignment

assign OUT = select ? A : B


if statement: if (select) OUT = A;

HDL Example 4-7 Behavioral description of a 2-to-1-line multiplexer


HDL Example 4-8

Behavioral description of a 4-to-1-line multiplexer


Writing a Simple Test Bench

Initial block

Three-bit truth table



Interaction between stimulus and design modules



Stimulus module

System tasks for display


Syntax for $dispaly, $write, and $monitor:

Example:

Example:


HDL Example 4-9

Stimulus module


HDL Example 4-9 (Continued)


HDL Example 4-10

Gate-level description of a full adder


HDL Example 4-10 (Continued)

digital system ch4-1 chapter 4 combinational logic ping-liang lai ( 賴秉樑 ) digital system...

Documents