Borqs

第 1� 页 共 19� 页

Firebolt User Manual

V1.0.0

Borqs

第 2� 页 共 19� 页

Contents

FireBolt Introduction.........................................................................................................................3

How to enable the Flash Mode..........................................................................................................3

JadeSpring enters the flash mode......................................................................................3

Spark enters the flash mode ..............................................................................................3

Download process .............................................................................................................................3

Log file..............................................................................................................................................7

Driver installation .............................................................................................................................7

Jadespring driver installation ....................................................................................................7

Borqs OBM USB Host Driver ..........................................................................................8

Borqs Ramdownloader USB Host Driver .......................................................................12

Spark driver installation ..........................................................................................................13

Marvell PTK Tavor BootLoader Device Driver..............................................................13

Marvell PTK Flasher Device Driver ...............................................................................18

Borqs

第 3� 页 共 19� 页

FireBolt Introduction

FireBolt is a download software for phone, developed by borqs(beijing).It

can download the suffix .MFF file. At present, two kind of phones are

supported, SPARK and Jadespring.

The current Firebolt newest edition is 1.0.15

How to enable the Flash Mode

JadeSpring enters the flash mode

Press the round key at the top left of the phone when powering the up phone. And press

the key with 2~4 seconds. The phone will enter the flash mode.

Spark enters the flash mode

Press the flash key when powering the up phone, or Serial port input “F” key. The

phone will enter the flash mode.

Download process

Launch Firebolt , When the USB device connect is incorrect, or phone has not

entered Flash Mode. The red icon will appear like follow:

Borqs

第 4� 页 共 19� 页

When the USB device connect is correct and the phone has entered Flash Mode. The

green icon will appear like follow:

Borqs

第 5� 页 共 19� 页

Click "..." button to select the "*. mff" file, As follows:

Borqs

第 6� 页 共 19� 页

Click on "flash" button to start downloading files:

Borqs

第 7� 页 共 19� 页

After the success of the downloading files, “ Flash successful” will be displayed in the

Status column as the below picture.

Log file

Under normal circumstances, FireBolt do not generate Log files. After program run,

Presses “Ctrl+L” key combination to generate Log files. In general the log files loactes in

“C:\Program Files\Borqs\Borqs Firebolt\”. That is the information of downloading process.

Driver installation

Jadespring driver installation

There are two drivers will need to install. The first is to be installed before

download, Select BORQSOBM.inf.

After installation, the Device Manager displays：Borqs(R) Driver: Borqs OBM USB

Host Driver

The second is to be installed during the middle of the downloading, Select

Borqs

第 8� 页 共 19� 页

BORQSDKB.inf.

After installation, the Device Manager displays ： Borqs(R) Driver: Borqs

Ramdownloader USB Host Driver

Borqs OBM USB Host Driver

Launch phone to enter the Flash Mode，Connect to the PC through the UBS line. Open

the device manager.

If the USB device did not identify: Borqs(R) Driver: Borqs OBM USB Host Driver. Need

to update drivers.

In the following chart, with an exclamation point of the drive has question.

Right-click on the device like the the following chart:

Borqs

第 9� 页 共 19� 页

Click the Update Driver, and then select “Install from a list or specific location”, the

following chart will appear:

Next, select “Don’t search. I will choose the driver to install.”

Borqs

第 10� 页 共 19� 页

Next, select “Have Disk…”

Select BORQSOBM.inf in the installation package, the general location is C:\Program

Files\Borqs\Borqs Firebolt\BorqsDriver

The following chart:

Borqs

第 11� 页 共 19� 页

Next, driver will copy the system folder, As follows:

Finally the a dialog will prompt installs successfully!

Borqs

第 12� 页 共 19� 页

With this step, the first driver have been installed.

Borqs Ramdownloader USB Host Driver

After the files chooses, to launch FireBolt to download those. When the USB device to open a

second time, need to install driver. Installs the method with first time, only chooses

BORQSDKB.inf file. After installed, the Device Manager displays:

Borqs

第 13� 页 共 19� 页

Spark driver installation

The two drivers will need to install. The first is installed before download, Select

acatusb.inf.

After installation, the Device Manager displays：Marvell PTK Tavor BootLoader

Device Driver

The second is installed before download, Select acatusb.inf.

After installation, the Device Manager displays：Marvell PTK Flasher Device Driver

Here's how:

Marvell PTK Tavor BootLoader Device Driver

Launch phone to enter the Flash Mode，Connect to the PC through the UBS line. Open

the device manager.

If the USB device did not identify: Marvell PTK Tavor BootLoader Device Driver. Need

to update drivers.

The following chart, with an exclamation point of the drive has question.

Borqs

第 14� 页 共 19� 页

Right-click on the device, the following chart:

Click the Update Driver, and then select “Install from a list or specific location”, the

following chart:

Borqs

第 15� 页 共 19� 页

Next, select “Don’t search. I will choose the driver to install.”

Next, select “Have Disk…”

Borqs

第 16� 页 共 19� 页

Select acatusb.inf in the installation package, the general location is C:\Program

Files\Borqs\Borqs Firebolt\ spark_usb

The following chart:

Next, driver will copy the system folder, As follows:

Borqs

第 17� 页 共 19� 页

Finally the prompt installs successfully!

Borqs

第 18� 页 共 19� 页

To this step, the first already installed。

Marvell PTK Flasher Device Driver

After the files chooses, to launch FireBolt to download those. When the USB device

to open a second time, need to install driver.

Borqs

第 19� 页 共 19� 页

Installs the method with first time, only chooses acatusb.inf file. After installed, the

Device Manager displays: