infraworks

Demonstration: ProfileView NavigationIn this demonstration, you view the roadprofile and adjust the viewing of the profile.

Demonstration SetupBefore you can complete thesedemonstrations, you must first havedownloaded the dataset that is included inthe first demonstration.1. Select the road you were previously

driving along.

2. Select the Profile View button on theView tab.

3. Use the divider controls at the bottomof the profile view to control therange displayed.

4. Use the slider at the bottom of viewto move the range around the profile.

Page 1 of 1

12.03.2014http://sstelearning.autodesk.com/sstelprd/servlet/ViewGroup?grou...

Demonstration: VerticalOptimization - JobSubmissionIn this demonstration, you will examinesubmission of a job to the verticaloptimization service.

You will do the following:

Choose the road to optimize Adjust optimization options Submit the optimization job Check the status of your

optimization

Demonstration SetupBefore you can complete thesedemonstrations, you must first havedownloaded the dataset that is included inthe first demonstration.1. Select the bookmark for the Vertical

Profile.

2. Select the Optimize Tab.

3. First open the Construction &Earthworks Cost Dialog

Examine the settings for costs.

4. Press OK.5. Select the profile view button.6. Select the road in canvas.

Page 1 of 3


7. Examine the current profile design.

8. Select the Vertical Optimization button.

The Vertical Optimization panel willdisplay.

9. In order to submit a vertical optimizationyou will need to have enough cloudcredits in your Autodesk 360 account inorder to proceed.

10. Login to Autodesk 360 on the Main toolbar.

11. Back in the optimization dialog selectthe click here to check in the dialog todetermine how many credits arerequired.

12. Press the Optimize It button to send thejob to the service.

13.Select the Job Monitor button to see thestatus of your optimization.

Page 2 of 3


of 3


Demonstration: RoadLayout ToolsIn this section of the demonstration, youwill examine the tools for laying out adesign road.


Layout roads of different types Identify differences rules have on

different road types.

Demonstration SetupBefore you can complete thesedemonstrations, you must first havedownloaded the dataset that is included inthe first demonstration.1. Select the proposed roadway

bookmark.

2. Select the Roads tool, choose localroad.

3. Draw a road in the proposedlocation.

4. Right click and choose end draw tocomplete the road.

5. Draw a second proposed road usingthe Freeway tool.

6. Observe the difference between thetwo tools.

Page 1 of 1


Demonstration: HorizontalEdit ToolsIn this section of the demonstration, youwill use the edit tools for adjusting thehorizontal layout of the road.


Change the type of a curve Adjust the Radius and Spiral length Examine curve properties Remove a curve Add a curve Adjust a curve in canvas

Demonstration SetupBefore you can complete thesedemonstrations, you must first havedownloaded the dataset that is included inthe first demonstration.1. Select one of the roads you created

in the previous exercise.

2. In a top down or nearly top downview right click near a curve.

3. Change the curve type.

4. Right click again near a curve andchoose edit curve.

5. Use the curve slider to adjust thecurve radius or spiral length(ifapplicable).

6. Right click near a curve and selectcurve properties.

7.

Examine the values in curveproperties.

Page 1 of 2


8. Select a curve in canvas and ensurethat its type is curve.

9. In Canvas use the gizmos to adjustthe curve radius.

10. Explore the remaining tools in theright click menu.

Page 2 of 2


Demonstration: VerticalEdit ToolsIn this section of the demonstration, youwill examine the tools available for editingthe vertical design of the roadway.


Identify a curve in model & profileview

Adjust a vertical curve length incanvas

Add & remove vertical curves incanvas

Edit vertical curves in profile view Recreate entire vertical design Examine vertical curve properties

Demonstration SetupBefore you can complete thesedemonstrations, you must first havedownloaded the dataset that is included inthe first demonstration.1. Rotate the view to be looking from an

angle greater than 45degrees to the sideof the roadway.

2. The vertical edit gizmos will appear inCanvas.

3. Use the PVI and Curve Length gizmos tomodify the vertical design of theroadway.

4. Right click and chose show in profile tobring up a profile view of the road.

5. Use the remove and add vertical curvecommands from the right click menu inCanvas.

6.

Use the same commands in the profileview right click menu to alter yourdesign.

Page 1 of 2


7. Use the recreate profile command torebuild the entire profile design based onthe predefined rules.

8. Examine vertical curve properties.

Page 2 of 2


Demonstration:Optimization ResultsIn this last section of the demonstration,you will examine how to obtain the resultsfrom a completed vertical optimization.


Check the status of youroptimization job

Review the optimization report Integrate updated results into your

model

Demonstration SetupBefore you can complete thesedemonstrations, you must first havedownloaded the dataset that is included inthe first demonstration.1. Select the optimize tab.

2. Select Job Monitor.

3. If auto refresh was not selectedpress the update button.

4. You will see a list of jobs you havesubmitted.

5. Press the report button to view thereport of the optimization results.

6. Examine the Report.7. Select the Results Icon.

8. You will be prompted to create anew proposal to store the results ofthe optimization.

9. Select yes and give the newproposal a name.

10. Open the profile view and select theroad to see the newly optimizedvertical profile design.

11. End of demonstration.

Page 1 of 1


infraworks

Documents