katherine 80010606 v01

Type No. 80010606V01

Frequency range 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2200 MHz

Azimuth direction Beam A (–30°), Beam B (+30°)

Polarization +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45°

Gain 4 x 19 dBi 4 x 19.3 dBi 4 x 19.5 dBi

Horizontal Pattern:Half-power beam width(offset beams ±30°)

47° 45° 43°

Front-to-back ratio Copolar: > 30 dBTotal power: > 25 dB

Cross polar ratioMaindirection –30°; +30°Sector –60°; 0°; 0°; +60°

Typically: 18 dB> 13 dB



Sidelobe sppression for sidelobes beside main beam

> 18 dB

Vertical Pattern:Half-power beam width 7.2° 7.1° 6.8°

Electrical tilt 0°–10°, continuously adjustable

Sidelobe suppression for fi rst sidelobe above main beam > 18 dB

Impedance 50 Ω

VSWR < 1.5

Isolation, between ports > 30 dB

Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier)

Max. power per input 200 W (at 50 °C ambient temperature)

KATHREIN-Werke KG · Anton-Kathrein-Straße 1 – 3 · P.O. Box 10 04 44 · 83004 Rosenheim · Germany · Phone +49 8031 184-0 · Fax +49 8031 184-973

www.kathrein.de

936.

4001

/c

Sub

ject

to a

ltera

tion.

XXPol Panel 1710–2200/1710–2200 45°(–30°)/45°(+30°) 19.5/19.5dBi 0°–10°/0°–10°T

1710–2200

Mechanical specifi cations

Input 4 x 7-16 female

Connector position Bottom

Wind load Frontal: 710 N (at 150 km/h)Lateral: 200 N (at 150 km/h)Rearside: 820 N (at 150 km/h)

Max. wind velocity 200 km/h

Height/width/depth 1314 / 380 / 150 mm

Category ofmounting hardware M (Medium)

Weight 19 kg / 21 kg (clamps incl.)

Packing size 1696 x 402 x 172 mm

Scope of supply Panel and 2 units of clampsfor 42 – 115 mm diameter

80010606V01 of 3

7-16 7-16

1710–2200–45°

Beam B(+30°)

1710–2200+45°

Beam B(+30°)

1710–2200+45°

Beam A(–30°)

1710–2200–45°

Beam A(–30°)

7-16 7-16

1710 – 1880 MHz

1850 – 1990 MHz

1920 – 2200 MHz

dB3

10

47°

47°

7.2°

Bd

10

3

dB3

10

45°

45°

dB3

10

43°

43°

7.1°

Bd

10

3

6.8°

Bd

10

3

Horizontal Pattern Vertical PatternBeam A (–30°), Beam B (+30°)

0°–10° electrical downtilt

Vertical PatternBeam A (–30°), Beam B (+30°)


Vertical PatternBeam A (–30°), Beam B (+30°)


Horizontal Pattern

Horizontal Pattern

Dual-Beam PanelDual PolarizationHalf-power Beam WidthAdjust. Electrical DowntiltAzimuth Beam DirectionOptimized Horizontal SidelobesDowntilt set by hand or by optional RCU (Remote Control Unit)

1710–22001710–2200

XX

45°45°

0°–10°

(+30°)

18dB

0°–10°

(—30°)

18dB

Beam A(–30°)

Beam A(–30°)

Beam A(–30°)

Beam B(+30°)

Beam B(+30°)

Beam B(+30°)


www.kathrein.de

936.

4001

/c

Sub

ject

to a

ltera

tion.

AccessoriesGeneral Information

Adjustmentmechanism

with integrated scale

1314

9

1484

1514

64

For wall mounting: Azimuth Adjustment Kit 85010016.For 3 Panel Arrangement: 3 Sector Clamp Kit 742034.

Material: Refl ector screen: Tin-plated copper. Radiator: Tin-plated zinc.Fiberglass radome: The grey fi berglass radomes of these antennas are very stable and extraordinarily stiff. They are resistant to ultraviolet radiation and can also be painted to match their surroundings.All screws and nuts: Stainless steel.

Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.

Environmental conditions: Kathrein cellular antennas are designed to operate under the environ-mental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regard to the following items:– Low temperature: –55 °C– High temperature (dry): +60 °C

Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions.

Environmental tests: Kathrein antennas have passed environmental tests as recommended in ETS 300 019-2-4. The homogenous design of Kathrein’s antenna families use identical modules and materials. Extensive tests have been performed on typical samples and modules.

Layout of interface:

Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions.

The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4 and thereby respects the static mechanical load imposed on an antenna by wind at maximum velocity. Wind loads are calculated according to DIN 1055-4. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process.

The installation team must be properly qualifi ed and also be familiar with the relevant national safety regulations.The details given in our data sheets have to be followed carefully when installing the antennas and accessories.The limits for the coupling torque of RF-connectors, recommended by the connector manufacturers must be obeyed.

Any previous datasheet issues have now become invalid.

of 3 80010606V01

Accessories

Type No. Description Remarks Weightapprox. Units per antenna

738546 1 clamp Mast: 42 – 115 mm diameter 1.1 kg 2 (included in the scope of supply)

731651 1 clamp Mast: 28 – 60 mm diameter 0.8 kg 2 (order separately if required)



135

150

380 Bottom view

57

120

50

Proposal for6 Sector Deployment


www.kathrein.de

936.

4001

/c

Sub

ject

to a

ltera

tion.

80010606V01 of 3

Example of 6 Sectors by using 3x 80010606 and 3 Sector Clamp Kit 742034

For the above 3 Panel Arrangement please use the 3 Sector Clamp Kit 742034 (order separately)

30°

210°

60°

240°

90°270°

120°

300°

150°

330°

180°

0°

Antenna IBeam A

Antenna IIBeam B

Antenna IIBeam A

Antenna IIIBeam B

Antenna IIIBeam A

Antenna IBeam B

0

3

6

10

20

Horizontal Patterns (top view)

Bottom view

Dout

470

mm

Antenna I

Antenna IIAntenna III

3 Sector Clamp Kit

Type No. 742034Angle between antennas 120°

Suitable for mast diameter 139.7 mm

Type no. of pipe mast(please order separately)

742036

Scope of supply 2 x 3 sector clamp2 x mounting support clamp

Material – 3 sector clamp – Mounting support

clamp – Screws – Nuts

Hot-dip galvanized steelAluminum

Hot-dip galvanized steel Stainless steel

Outer diameter (Dout) of the 3 Dual-Beam Panel Arrangement

470 mm

Weight – Clamp kit – 3 sector clamp

4 kg2 kg

3 Panel Arrangement

Mechanical specifi cations

Weight 60 kg

Wind load Frontal: 950 N (at 150 km)Lateral: 950 N (at 150 km)Rearside: 950 N (at 150 km)

Max. wind velocity 200 km/h

Type No. A B C D E F G742034 139.7 100 236 228 64 50 45

all dimensions in mm

E

A

D

M8

BC

60°

GF

Mounting support clamp

3 sector clampTorqueMA = 25 Nm

TorqueMA = 7 Nm

936.

4020

Sub

ject

to

alte

ratio

n.

Page 1 of 1

KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-973

Internet: www.kathrein.de

Remove the protective cap. Set downtilt angle by rotating theadjustment wheel.

0° – max.°

max.° – 0°

Manual adjustment procedure:

General Instructionsfor Adjustment Mechanism

Description of the adjustment mechanism (protective cap removed):

➀ Adjustment wheel with twist-lockfunction.

➁ Downtilt spindle with integratedscale.

➀ Thread for fixing the protectivecap or the RCU (Remote ControlUnit).

➁ Gearwheel for RCU power drive.

2

12

1

To set the downtilt angle exactly,you must look horizontally at thescale. The lower edge of the gear-wheel must be used for alignment.

Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:

For a description of RCU installation please refer to the respective data sheet.

Screw on the protective cap again.

katherine 80010606 v01

Technology