micro bbu (5)
TRANSCRIPT
7/28/2019 Micro BBU (5)
http://slidepdf.com/reader/full/micro-bbu-5 1/8
Installation Guide
Heater kit
Art. 351429.033Issue 1, 2005-09
7/28/2019 Micro BBU (5)
http://slidepdf.com/reader/full/micro-bbu-5 2/8
2 Installation Guide Heater Kit , 351429.033, v1-2005-09
Index
General .......................................................................................................................................2
Recommended tools ................................................................................................................... 2
Torque settings ........................................................................................................................... 2
Ordering information..................................................................................................................2
Scope of delivery........................................................................................................................3
Installation.................................................................................................................................. 4
General
The Heater Kit is intended for MircoPower Outdoor Systems and MicroPower Outdoor
Battery Cabinets situated in cold climates. If the cabinet inside temperature drops below 5°C
the heater will automatically start to heat up the cabinet. The heater will turn itself off when
the inside temperature reaches 15 °C. This will ensure that the batteries will last longer.
Installation must be done by authorized personnel only.
Eltek Energy recommends that the system is powered down before installation of the kit.
Recommended tools
Standard equipment used by an authorized electrician. NOTE: All tools have to be insulated.
Torque settings
• M6 screws for the DIN bar: 5.0Nm• Terminals on the heater: 1.5Nm
• M6 nut on the earth copper plate: 6.0Nm
Ordering information
Part number Description Net weight
105421 Heater kit 280gr
7/28/2019 Micro BBU (5)
http://slidepdf.com/reader/full/micro-bbu-5 3/8
Installation Guide Heater Kit , 351429.033, v1-2005-09 3
I n s t a l l a t i o n m a n u a l
E l t e k
X x x x x x x x x x
X x x x x x x x x x X x x x x x x x x x
9
Scope of delivery
The Kit for Heater consists of the following components.
Part Note Quantity Unit
Heater/FAN assembly 400W 120x120x47mm 1 1 pcs
Fixing rail DIN TS 35x7.5x100mm 2 1 pcs
BOLT HEXAGON m6x12 DIN 933 zinc 3 1 pcs
LOCK WASHER m6 DIN 128B zinc 4 1 pcs
Nut 6mm 5 (For square hole in inner side wall) 1 pcs
Loom: Heater MicroPower 6 1 pcs
SCREW TAPTITE TORX M6x12 7 1 pcs
STRAP PLT 1,5mm 0 PANDUIT 8 10 pcs
Manual 9 1 pcs
1
2
3,4&5
6
7
8
7/28/2019 Micro BBU (5)
http://slidepdf.com/reader/full/micro-bbu-5 4/8
4 Installation Guide Heater Kit , 351429.033, v1-2005-09
Installation
Step Description Comment OK
1 Switch off the external
AC breaker and the battery breaker.
2 Remove the batteries and
the battery shelf.
3 Put the boxed nut into the
4th inner square hole from
the bottom. Mount the
DIN rail with the hex bolt
through the boxed nut and
the M6 screw through theinner round hole.
Torque: 5.0Nm.
The DIN rail
position on the
left inner side
wall.
7/28/2019 Micro BBU (5)
http://slidepdf.com/reader/full/micro-bbu-5 5/8
Installation Guide Heater Kit , 351429.033, v1-2005-09 5
4 Connect the loom to the
heater.
First connect the
green/yellow cable at the
earth terminal on the
heater. Then connect the blue cable to N1 and the
black cable to L1.
5 Snap the heater on the
DIN rail.
6 Run the cables from the
heater to the earth plate
and the analog controller
board.
Connect the green/yellow
cable with the cable lug at
the earth copper plate.
Torque: 6.0Nm
Connect the blue (N)
cable at connector 1 pinnumber 3 (CON1-3).
The black (L) cable must
be connected to connector
1 pin 4 (CON1-4).
Fix the cables with cable
ties.
7/28/2019 Micro BBU (5)
http://slidepdf.com/reader/full/micro-bbu-5 6/8
6 Installation Guide Heater Kit , 351429.033, v1-2005-09
7 Remount the battery shelf.
Put the batteries on the
battery shelf again and
reconnect the battery
cables.
Switch on the battery breaker and the external
AC breaker.
8 The Heater Kit has now
been installed.
7/28/2019 Micro BBU (5)
http://slidepdf.com/reader/full/micro-bbu-5 7/8
Installation Guide Heater Kit , 351429.033, v1-2005-09 7
7/28/2019 Micro BBU (5)
http://slidepdf.com/reader/full/micro-bbu-5 8/8
ELTEK Energy P-O- BOX 2340 StØmsØ N-3003 DRAMMENNORWAY
Phone: +4732203200Telefax: +47 32203210Internet: http://www.eltekenergy.come-mail: [email protected]