micro bbu (9)
TRANSCRIPT
7/28/2019 Micro BBU (9)
http://slidepdf.com/reader/full/micro-bbu-9 1/8
Installation Guide
Kit for Wall Mounting
Art. 351424.033Issue 1, 2005-09
7/28/2019 Micro BBU (9)
http://slidepdf.com/reader/full/micro-bbu-9 2/8
Installation Guide Wall Mounting Kit, Art. 351424.033, v1-2005-09 Page 2 of 8
Index
General .......................................................................................................................................2
Recommended tools ................................................................................................................... 2
Torque settings ........................................................................................................................... 2
Ordering information.................................................................................................................. 2
Scope of delivery........................................................................................................................3
Drilling Template ....................................................................................................................... 4
Installation..................................................................................................................................5
General
The Kit for Wall Mounting makes it possible to mount the MicroPower Outdoor Cabinet to a
wall. Minimum 2 persons should cooperate during this installation. Installation must be done by authorized personnel only.
The Kit for Pole Mounting is designed to support the MicroPower Outdoor Cabinet with one
battery bank. Do not put additional weight on top/into the system once it has been installed on
a wall.
Eltek Energy recommends that the system is powered down before installation of the kit.
Recommended tools
Standard equipment used by an authorized electrician. NOTE: All tools must be insulated.
Lifting equipment should be used for safety reasons.
Torque settings
• M8 screws wall mounting kit/rear side of cabinet: 10Nm
• M8 screws (not delivered with this kit) for wall: Minimum10Nm
Ordering information
Part number Description Net weight Gross weight Lot size
105287 Kit for WallMounting
2700gr 3700gr 83pcs
7/28/2019 Micro BBU (9)
http://slidepdf.com/reader/full/micro-bbu-9 3/8
Installation Guide Wall Mounting Kit, Art. 351424.033, v1-2005-09 Page 3 of 8
Scope of delivery
I n s t a l l a t i o n m a n u a l
E l t e k
X x x x x x x x x x
X x x x x x x x x x X x x x x x x x x x
5
(1) Cross member 2 pcs, (2) Hexagon head screw M8x20 4 pcs,(3) Spring washer 8.1Ø 4 pcs, (4) Flat washer 8.4Ø 4 pcs, (5) Manual 1 pcs.
7/28/2019 Micro BBU (9)
http://slidepdf.com/reader/full/micro-bbu-9 4/8
Installation Guide Wall Mounting Kit, Art. 351424.033, v1-2005-09 Page 4 of 8
Drilling Template
Figure 1. Drilling template for the wall mounting kit.
Lower wall mount bar
Upper wall mount bar
530mm
400mm122mm
17 mm
123mm
505mm
160mm
Top of cabinet
Bottom of cabinet
Holes for screws intowall
Holes for screws intorearside of cabinet
775mm
590mm
7/28/2019 Micro BBU (9)
http://slidepdf.com/reader/full/micro-bbu-9 5/8
Installation Guide Wall Mounting Kit, Art. 351424.033, v1-2005-09 Page 5 of 8
Installation
Step Description Comment OK
1 Mount both cross-memebersto the wall. The bars are
identical. See Figure 1 for a
drilling template. Let the key
holes face upwards.
The mounting hardware for
fitting the cross members to
the wall is not in scope of
delivery because there are
many different types of
materials used for walls.
Torque: Minimum10Nm.
2 Fit the four M8 screws into
the rear side of the cabinet.
Do not tighten these screws
yet. Let each screw stick out
5-7mm.
Fix the metal bars to a
wall through these holes.
7/28/2019 Micro BBU (9)
http://slidepdf.com/reader/full/micro-bbu-9 6/8
Installation Guide Wall Mounting Kit, Art. 351424.033, v1-2005-09 Page 6 of 8
3 Demount the cabinet roof
and fix straps to the eye-
bolts. Lock the door so it
does not swing during
lifting. Lift the cabinet with
lifting equipment attached tothe straps.
Balance the cabinet to
prevent it from swinging.
NOTE! Do not lift the
cabinet with batteries
installed.
Warning! Do not stay under
the cabinet during
installation.
4 Position the cabinet above
the wall brackets. Lower the
cabinet slowly. Let the
screws on the rear side of
the cabinet slide into the key
holes in the wall brackets.
Check that the screw heads
and washers all enter the
inside of the brackets.
Tighten the screws.
Torque: 10Nm.
5 Remove the straps and
remount the roof.
The electrical installation
can now begin.
7/28/2019 Micro BBU (9)
http://slidepdf.com/reader/full/micro-bbu-9 7/8
Installation Guide Wall Mounting Kit, Art. 351424.033, v1-2005-09 Page 7 of 8
7/28/2019 Micro BBU (9)
http://slidepdf.com/reader/full/micro-bbu-9 8/8
ELTEK Energy P-O- BOX 2340 StØmsØ N-3003 DRAMMENNORWAY
Phone: +4732203200Telefax: +47 32203210Internet: http://www.eltekenergy.come-mail: [email protected]