rajasthan sor
TRANSCRIPT
-
7/31/2019 Rajasthan SOR
1/37
SL. NO DESCRIPTION UNIT RATE(A) COMPOUND WALL / CULVERT / BLDG. / YARDLIGHT / TANKS / PUMP INSTALL. EXCEPT DRIVEWAY
1 FINANCIAL LIMIT
SITE SURVEY
2 SITE SURVEY UPTO 2000 SQM Lump Sum 6500
3 From 2001 to 10000 SQM Lump Sum 8500
4 ACRE BEYOND 10000 SQM Lump Sum 2750
5 SITE CLEARANCE SquareMetres
2
6 EXCAVATION IN EARTH 3M CubicMetres
95
8 EXCAVATION-HARD ROCK3m CubicMetres 480
10 SAND FILLING - LAYERS
-
7/31/2019 Rajasthan SOR
2/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
15 PCC WORK-1:2:4 CubicMetres
2630
16 PCC WORK-1:3:6 Cubic
Metres2060
17 PCC WORK-1:4:8 CubicMetres 1825
18 PCC WORK-1:5:10 CubicMetres
1535
19 PCC 1:1.5:3 FOR DPC SquareMetres
190
20PCC 1:1.5:3-GROUT. MS STRUCT. Cubic
Metres 3060
21 RCC1:1.5:3 FOUND. / PLNTH. / RET. WAL CubicMetres 3260
22 RCC1:1.5:3 COLUMNS / SLAB / TIE / CULVERT ETC. CubicMetres 3360
23 RCC1:1.5:3 FOR COPING CubicMetres
3360
24 UNDER REAMED PILES-150 MM RunningMetre
435
25 UNDER REAMED PILES-230 MM RunningMetre
505
26 UNDER REAMED PILES-300 MM RunningMetre
650
27 UNDER REAMED PILES-350 MM RunningMetre
740
28 REINFORCEMENT STEEL IS:1786 Metric Ton 36500
29 BRICK MASONRY: SUB STR.-NEW BRICK CubicMetres
1840
PCC WORK : Providing and laying PCC using graded stone aggregate of specified size and down. The job includes machine mixing, providing formwork,
MS/plywood (minimum 19 mm thick) shuttering if directed by Engg.-In-Charge, placing, compacting by hand ramming, curing for a period of 14 days etc, all
complete as per direction of Engg.-In-Charge. Removing of shuttering to be done carefully without such shock and vibration as to damage the PCC work. For
PCC 1:1.5:3 using 20 mm and down size graded stone aggregates. Vibrator to be used whenever directed by Engg.-in-Charge without any extra cost.
Same as Item No.14 but for PCC 1:2:4 using 20 mm and down size graded stone aggregates
Same as Item No.14 but for PCC 1:3:6 using 20 mm and down size graded stone aggregates
Same as Item No.14 but for PCC 1:4:8 using 40 mm and down size graded stone aggregates
Same as Item No.14 but for PCC 1:5:10 using 40 mm and down size graded stone aggregates
PCC 1:1.5:3 FOR DPC: Providing and laying 50 mm thick DPC in 1:1.5:3 mix with 6 to 12 mm size aggregate and waterproofing compound of approved ISI
make at the rate of 1 kg per bag of cement. Job includes all formwork, side MS/plywood (Minimum 19 mm thick) shuttering, proper compaction, hand
ramming and curing for 14 days, and supplying / applying a coat of hot bitumen of grade 60/70 on top, all complete including spreading of sand as required.
Providing and laying PCC 1:1.5:3 mix using 20mm and down stone aggregate for grouting Angles / MS Structurals. Other specs as per item no. 14. MS
Structurals will be paid separately.
REINFORCED CEMENT CONCRETE: Providing, Mixing, laying and placing RCC 1:1.5:3 mix with Ordinary Portland Cement using 20 mm and down size
graded crushed stone aggregate including providing and fixing necessary plywood (minimum 19 mm thick) / steel shuttering, scaffolding, machine mixing,
compacting by mechanical vibrators (needle / skid etc), curing, hacking the surface to receive plaster using plastic / PVC sheet of thickness minimum 20
micron under RCC, as directed wherever required etc. all complete. Machine mixing to be done without exception. Rate shall be exclusive of the cost of steel
reinforcement. Concreteshall conform to relevant specifications of IS 456:2000 Latest Edition. For footings / foundations / plinth beam / floor beam / retaining
wall etc.
Superplasticiser Rheobuild SP1 (Napthalene base) shall be dosed in mixing water after 50-70% of mixing water has been added in the mixer machine. The
dosage wil l be in the range of 0.6% to 0.8% by weight of cement (i.e. 300ml - 400ml per 50 kg. bag of cement) to get desired workabil ity. Equivalent
Napthalene based superplasticiser may be used in manufacturer's specified proportions / methods after prior approval of Engg.-in-Charge .
Same as Item No. 21 bu t for Column / Tie beams / Chhajja / Lintel / roof slab / stair case / culvert slab etc.
Same as Item No.21 but for Coping
Earth work under pile foundation of specified dia til l specif ied depth using hand auger or mechanical auger as approved in ordinary soil true to plumb,
providing M-25 concrete for under reamed piles up to required depth with bulbs as directed and as per IS:2911 etc. complete as per design and direction of
Engg.-In-Charge. Reinforcement steel shall be paid separately. 150 mm d iameter.
Same as Item No.24 but for 230mm dia
Same as Item No.24 but for 300mm dia
Same as Item No.24 but for 350 mm dia
REINFORCEMENT STEEL Supply, fabrication, hoisting and placing in position HYSD reinforcement bars conforming to IS:1786-Latest Edition of Grade FE-
415 / TMT bars of same grade as per detailed drawing and specifications including cutting, bending, cranking and tying with 18 SWG black annealed binding
wire complete. The rates shall be applicable for all heights and depths. Payment shall be made as per reinforcement drawings and with theoretical weights
only including all authorised laps, chairs, spacers and hooks.
Bidder's Seal & Signature Page 2 of 37
-
7/31/2019 Rajasthan SOR
3/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
30 BRICK MASONRY: SUB STR-OLD BRICKS CubicMetres
790
31 BRICK MASONRY: SUPER ST.-NEW BRICK CubicMetres
1960
32 BRICK MASONRY: SUPER ST-OLD BRICKS CubicMetres
820
33 PARTITION 115-NEW BRICK MASONRY Square
Metres
270
34 RANDOM RUBBLE MASONRY-SUB STR. CubicMetres
1345
35 RANDOM RUBBLE MASONRY-SUPER STR. CubicMetres
1410
36 MASONARY WITH CC BLOCKS CubicMetres 3400
37 DRESSED STONE MASONRY CubicMetres
1800
38 RUBBLE PITCHING 230 MM THICK SquareMetres
95
39 RUBBLE PITCHING 150 MM THICK SquareMetres
75
40 RUBBLE SOLING 230 MM THICK SquareMetres
95
BRICK MASONRY WORKS: Providing and constructing following brick masonry in CM 1:5 using locally available bricks of Class designation 75 (minimum)
and conforming to IS 1077:1986 including providing all openings and projections, raking the joints to 1 cm deep, scaffolding, soaking of bricks in water prior
to use and curing etc all complete as per specifications .
SUB STRUCTURE: Providing and laying brick masonry as above for foundation below DPC level.
SUB STRUCTURE below DPC level: Same as item no. 29 but using old bricks taken out from demolished masonry. Rate includes removing mortars and
cleaning of bricks etc. complete. Once the demolition is over, the party has to take out the usable good bricks and stack them properly to enable Engg.-In-
Charge to assess the quantity of bricks for future reference and calculation. Once the assessment is made it is dutyof the contractor to obtain certificate from
Engg.-In-Charge about the quantity of usable bricks available before these bricks are put to use. In absence of certificate no payment will be made. However,in no case the old bricks shall be used without the assessment of quantity and clearance to use the old bricks is given by the Engg.-In-Charge.
SUPER STRUCTURES. Providing and laying brick Masonry as item no. 29 but for superstructure above DPC level including scaffolding.
SUPER STRUCTURE: Same as item no. 29 but using old bricks taken out from demolished masonry. Rate includes removing mortars and cleaning of bricks
etc. complete. Once the demolition is over, the party has to take out the usable good bricks and stack them properly to enable Engg.-In-Charge to assess the
quantity of bricks for future reference and calculation. Once the assessment is made it is duty of the contractor to obtain certificate from Engg.-In-Charge
about the quantity of usable bricks available before these bricks are put to use. In absence of certificate no payment will be made. However, in no case the old
bricks shall be used without the assessment of quantity and clearance to use the old bricks is given by the Engg.-In-Charge.
Same as item no.29 but for 115 mm thick in part it ion walls in CM 1:4. Rate to include providing 75 mm thick RCC 1:1.5:3 bands using 2 nos 8 mm dia
Torsteel reinforcement at every 1 M height of wall including plywood / MS shuttering. Steel reinforcement shall be paid for separately.
Providing and constructing random rubble masonry with good quality stone in CM 1:5 for substructure & superstructure as per IS:1597, part-1, latest edition.
Rate to include soaking stones, raking the joints to 1 cm deep and curing complete. One Through / Bond stone shall be provided for every square meter of
facing, evenly distributed in a staggered pattern. They shall have about 0.03 sqm in face area and shall have a tailing for the full width of masonry upto
600mm.
If masonry wall is over 600mm thick, a line of headers (not less than 450mm length ) overlapping each other by 150mm shall be laid. Bond stones shall be
distinctly marked on its face during construction for verification. Quoin / key / corner stone shall not be less than 0.03 cum in volume. FOR SUBSTRUCTURE
Same as item no. 34 but FOR SUPERSTRUCTURE including scaffolding
Providing rubble pitching including surface dressing, making required slope. Rate to exclude flush pointing which will be paid for separately. 230 mm thick.
Masonry with CC blocks of size 400mm X 200mm X 200mm in CM 1:3. The concrete blocks to be moulded with mix 1:3:6 using 1 part of cement, 3 parts of
course sand and 6 parts of 40mm downsize graded stone aggregate. The job includes casting of CC blocks with the help of moulds by machine mixed mix of
1:3:6 in steel / wooden moulds, placing, compacting by hand ramming, pond curing of the blocks for a period of 14 days etc, all complete. Care to be taken
while removing of moulding to be done carefully without such shock and vibration as to damage the block. Masonry to be carried out with these blocks in CM
1:3 (1 part of cement and 3 parts of course sand). Scope of job includes raking the joints to 1 cm deep, scaffolding, curing etc. all complete as per
specifications. The masonry to be done in the fashion similar to the brick masonary. 12.0 mm plastering shall be done on the masonry, which shall be paid
separately under plastering head. .
Providing and constructing dressed stone masonry with good quality hard dressed stone in CM 1:5 for substructure & superstructure as per IS:1597, part-1,
latest edition. Rate to include soaking stones, raking the joints to 1 cm deep and curing complete. One Through / Bond stone shall be provided for every
square meter of facing, evenly distributed in a staggered pat tern. The stone masonry wall should have a facing of dressed stone on one side and the face
should be at least 150mm X 150mm. No plaster should be done on such face.
If masonry wall is over 600mm thick, a line of headers (not less than 450mm length ) overlapping each other by 150mm shall be laid. Bond stones shall be
distinctly marked on its face during construction for verification. Quoin / key / corner stone shall not be less than 0.03 cum in volume.
Same as item no. 38 but for 150 mm thick
Providing rubble soling including surface dressing, making required slope, soaking the rubbles before laying, packing the gaps using small size rubble / stone
/ murrum/stone dust/sand, and hand ramming / using mechanical roller / compactor as per site requirement all complete. 230 mm thick
Bidder's Seal & Signature Page 3 of 37
-
7/31/2019 Rajasthan SOR
4/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
41 RUBBLE SOLING 150 MM THICK SquareMetres
80
42 FLUSH POINTING-1:3 CM MIX SquareMetres
42
43 RAISED POINTING-5MM,1:3 CM MIX SquareMetres
49
44 RAISED POINTING-12MM,1:3 CM MIX SquareMetres
68
45 BRICK FLAT SOLING: SINGLE LAYER SquareMetres
115
46 BRICK FLAT SOLING:DOUBLE LAYER SquareMetres
220
47 BRICK ON EDGE SOLING-4.5 THK. SquareMetres
170
48 PLASTERING 20MM THK. SANDFACED SquareMetres
105
49 PLASTERING 12 MM THICK SquareMetres
65
50 PLASTERING 6 MM THICK SquareMetres
44
51 WEEP HOLES 75 MM DIA PVC RunningMetre
195
52 STRUCT. STEEL: ANGLE IRON POST Metric Ton 44000
53 STAINLESS STEEL RAILG. & OTHERS KG 335
54 PIPE RAILING-IS:1239 / IS:1161 RunningMetre
255
55 CHAIN LINK FENCE, 50x50,10SWG GI SquareMetres
240
Same as item no. 40 but for 150mm thick
Providing flush pointing in rubble pitching with 1:3 cement mortar including curing etc. complete.
Providing raised pointing 5 mm with CM 1:3 along the joints of exposed stone masonry. The joints shall be raked & cleaned, curing etc. all complete.
Providing raised pointing 12 mm with CM 1:3 along the joints of exposed stone masonry. The joints shall be raked & cleaned, curing etc. all complete.
Providing Brick soling 3.5" thick (including sand bedding), surface dressing, making required slope, soaking the bricks before laying, packing the gaps using
sand and watering etc. all complete.
Double layer Brick flat soling: Specifications same as item no. 45. Thickness 7.0"
Providing Brick on edge soling 4.5" thick (including sand bedding), surface dressing, making required slope, soaking the bricks before laying, packing the
gaps using sand and watering etc all complete.
Providing and laying average 20 mm thick sand faced cement plaster in ratio 1: 3 :1(cement; f ine sand : coarse sand) in two coats. Rate to include use of
water proofing compound as per manufacturer's recommendation. Rate shall include providing necessary scaffolding, chicken wire mesh at all joints of brick
and concrete surfaces, with a minimum overlap of 150 mm in all directions and curing complete. No extra payment shall be made for additional thickness if
required to achieve perfect line and level. The job includes cleaning, wetting of surface before plastering, curing etc all complete. Required grooves to be
formed as directed.
Same as item no.48 but 12 mm thick plaster in ratio 1: 3 :1(cement; fine sand : coarse sand) in single coat.
Same as item no.48 but 6 mm plaster in 1:4 (cement: fine sand) to ceiling surfaces / beams etc as required.
WEEP HOLES Providing, fabricating and installing in place, 75 mm dia., 6Kg / sqcm PVC Pipes of various lengths & at places as approved and directed at
site on the masonry wall for water drainage. The pipes shall be fixed with nylon jali using resin / glue on inside end of wall.
Supply, fabrication, erection and grouting of MS structurals in PCC 1:1.5:3 as per direction of Engg.-In-Charge. Rate to include fabrication of the post as per
the specification, erecting, placing, grouting to required depths and painting of the posts with two coats of Synthetic Enamel over two coats of Red Oxide
Primer. Excavation and PCC shall be paid separately.
Supply, fabrication, erection, giving finish and grouting of Stainless Steel (SS-304) railing, grab bar, balustrade, island guards & others made out of 1.6 to 3
mm wall thickness pipes of up to 50 NB dia./50mm square tubes and upto 6 mm thick SS plates including fasteners. The job shall be completed in str ict
conformity to architectural drawing with neat workmanship. The location of joints, junctions and joineries shall be indicated in a drawing prepared by the
contractor and prior approval of HPCL shall be taken for the same. Generally joints will not be allowed except at joining points of other members. The welding
procedure, tools and machinery and electrodes shall be as per BIS specifications for SS-304 fabrication. Payment shall be made basis weight of finished SS
pipes / tubes / plates only with no allowances for wastage, nuts and bolts etc. Contractor has to submit purchase proof ofSS pipes. Additionally samples will
be drawn from the SS sections so used and will be tested in a reputed laboratory for conformity to SS-304 parameters and physical details at contractor's
cost.
Supply and fixing of 40 NB medium duty MS pipes conforming to IS:1239 / IS:1161 YST 21 latest addition for top and bottom railings to the angle iron posts
for fixing the edges of the chain link fencing. Rate to include fabricating, cutting, bending of the MS pipe whereever necessary. Supply and fixing of the
required size MS clamps at every post, with required size nuts and bolts and painting therailing with two coats ofRed oxide Primerand two coats ofSynthetic
enamel paint after necessary cleaning and scrapping.
Bidder's Seal & Signature Page 4 of 37
-
7/31/2019 Rajasthan SOR
5/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
56 BARBED WIRE FENCING ON Y ANGLE RunningMetre
75
57 BARBED WIRE FENCING RunningMetre
125
58 MS GRILL / STAIR CASE Metric Ton 44000
59 MS GRATING & ISLAND COVER FRAME Metric Ton 45250
60 RCC HUME PIPE, NP3, 1000 NB RunningMetre
4200
61 RCC HUME PIPE, NP3, 600 NB RunningMetre
2800
Same as item no.60 but for diameter 600 mm NB
62 RCC HUME PIPE, NP3, 450 NB RunningMetre
1475
Same as item no.60 but for diameter 450mm NB
63 RCC HUME PIPE, NP3, 300 NB RunningMetre
760
Same as item no.60 but for diameter 300mm NB
64 RCC HUME PIPE, NP3, 250 NB RunningMetre
615
Same as item no.60 but for diameter 250mm NB
65 RCC HUME PIPE, NP3, 200 NB RunningMetre
475
Same as item no.60 but for diameter 200mm NB
66 RCC HUME PIPE, NP3, 150 NB RunningMetre
360
Same as item no.60 but for diameter 150mm NB and NP-3
67 ANTI TERMITE TREATMENT SquareMetres
275
Supply and fixing of50 x 50mm opening size, 10 SWG, GI chain link fencing to the angle ironpost with 8 SWGGI hooks and nuts and railing with 14 SWG
GI continuous wire up to a height of 1.8 m from the ground level. Rate to include unrolling the bundle, erecting, tightening and fixing at 300 mm C/C on the
vertical portion of the posts to every top and bottom railing with 14 gauge GI wire complete as per drawing. Angle post to be paid separately as per relevant
item.
Providing and fixing barbed wire in 10 rows horizontal with two ply 12 SWG GI barbed wire fencing with barbes @ 100mm C/C using GI hooks etc all
complete to angle / MS structurals posts grouted as per direction of Engg.-In-Charge, complete as per drawing. MS structurals / Angle post shall be paid for
separately. For payment purpose, measurement shall be taken for the length of plot boundary. No measurement shall be taken for 10 rows individually.
Providing and fixing barbed wire in 13 rows horizontal and 2 diagonals with two ply 12 SWG GI barbed wire fencing with barbes @ 100mm C/C using GI
hooks etc all complete to angle / MS structurals posts grouted in CC 1:1.5:3 as per direction of Engg.-In-Charge, complete as per drawing. MS structurals /
Angle post shall be paid for separately. For payment purpose, measurement shall be taken for the length of fencing. No measurement shall be taken for 13
rows individually.
Supply, installation and fixing of Prefabricated MS grill / Monkey Ladder / Stair case / baluster / MS Bars (IS:2062 Latest Edition) on compound wall using
MS structurals / bars / hollowsections / strips / pipes etc as per design given by HPCL and direction ofEngg.-In-Charge. Rate to includeerection, grouting of
posts in PCC 1:1.5:3, painting by two coats ofred oxide primer and two coats of synthetic enamel ofapproved shade. Grouting PCC to be paid separately as
per relevant item.
Providing, fabricating, welding and fixing structural steel in position with angle iron / flats / tees / squares / SHS tubes conforming to IS:4923-1997, plates etc
as per design and direction given by Engg.-In-Charge for drain grating, manhole frames, gratings, tree guards, Island covering frame etc, as per requirement.
Job includes all necessary grouting, supply and fixing of handles, nuts - bolts etc, painting the grating with 2 coats of approved synthetic enamel paint, over a
coat of red oxide primer.
Supplying, laying, aligning and joining following size NP3 class RCC Hume pipes of approved make conforming to IS-458 Latest Edition, as per direction of
Engg.-In-Charge. Rate to include excavation to required depth as per direction of Engg.-In-Charge (minimum earth cushion to be ensured) and providing 4"
thick and (outer dia in mm+200mm) wide PCC 1:5:10 below the Hume pipe as bed, 4" thick fine sand cushion all around the Hume pipe, back fill ing,
compaction, curing and testing joints against leakage.
Rate to include supplying and fixing ofrequired collars and fixing the same by using cement mortar1:3. All pipes must be new and perfectly sound, freefrom
cracks, cylindrical, straight and of standard nominal diameter and length with even texture. Test certificates from manufacturer shall be submitted and
approved by Engg. -In-Charge before use, all complete. Diameter 1000mm NB
Providing anti-termite treatment including diluting and injecting chemical emulsion / NEEM based solution and creating a continuous chemical barrier under
and all around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor, along the external perimeter of
building, expansion joints, over the top surface of consolidated earth on which apron is to be laid, surroundings of pipes and conduits etc. complete as per
specification using Chlorpyriphos emulsifiable concentrate (20%) in 1% concentration or as specified by manufacturer.
Plinth area of building at ground floor only shall be measured for payment. The work shall be carried out by a qualified agency as approved by Engg.-In-
Charge. Contractor will have to submit 10 years guarantee bond on Rs. 100/- stamp paper for the treatment.
Bidder's Seal & Signature Page 5 of 37
-
7/31/2019 Rajasthan SOR
6/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
68 CERAMIC TILE FLOORING SquareMetres
680
69 VITRIFIED TILE FLOOR NLT 700 SquareMetres
1190
70 VITRIFIED TILE FLOOR NLT 1000 SquareMetres
1580
Same as item no. 69 but Basic rate not lower than Rs. 1000/- per sqm
71VITRIFIED TILE FLOOR - SINTRA Square
Metres 1900
72 VITRIFIED TILE FLOOR-S&P GREY SquareMetres
1410
73 VITRIFD TILE FLOOR-SNOW CARARA SquareMetres
2090
74 VITRIFD TILE FLOOR-OLYMPOUS SquareMetres
1250
75 VITRIFIED TILE FLOORING-SAVONA SquareMetres
1400
Same as item no. 69 but of NITCO, Savona of size 600x600 mm or Approved Equivalent
76 VITRIFD TILE FLOORING-OCEAN MIST SquareMetres
1500
Same as item no. 69 but of NITCO, Ocean Mist of size 800x800 mm or Approved Equivalent
77 VITRIFIED TILE FLOORING-NOVARA BEIGE SquareMetres
1800
78 GRANITE TILE FLOOR 10 MM SquareMetres
1420
79MARBLE FLOORING Square
Metres 1125
Providing and laying matt finish Ceramic tiles ofapprox8 mm thick ofsizeas specified in flooring. The tiles used should be of KAJARIA make ofGroup - IV or
equivalent group of approved makes. The tiles should be of first quality of approved make and shade and free from cracks, warpage, fissures and flakes with
straight edges and perfect corner laid at right angle as per design & pattern over a bedding ofcement mortar 1:5 ofaverage 30 mm thick, finishing the joints
neatly with white cement mixed with matching colour pigment and finish in all respect with all material and labour complete
giving required slope as directed by Engg.-In-Charge. If necessary, surface unevenness shall be filled up with brick ballast manually compacted with watering
etc. complete as per instructions of Engg.-In-Charge without extra cost. Tiles size shall not be less than 300X300 mm. Basic Rate - Not lower than Rs.350 /
sqm.
Providing and laying polished vitrified Ceramic tiles of minimum 8 mm thick of size as specified in flooring. The tiles used should be of KAJARIA make or
equivalent approved makes. The tiles should be of first quality of approved make and shade and free from cracks, warpage, fissures and flakes with straight
edges and perfect corner laid at right angle using approved PVC corner spacers as per design and pattern over a bedding of cement mortar 1:5 of average
30 mm thick, finishing the joints neatly with white cement mixed with matching colour pigment/ Ball Adhesive and finish in all respect with all material and
labour complete giving required slope as d irected by Engg.-In-Charge.
Tiles size shall vary between 300x300 mm (minimum) and 600X600 mm (maximum) as directed by Engg.-In-Charge. If necessary, surface unevenness shall
be filled up with brick ballast manually compacted with watering etc. complete as per instructions of Engg.-In-Charge without extra cost. Basic rate not lower
than Rs. 700/- per sqm.
Same as item no. 69 but of H & R Johnson(Marbonite), Sintra of size 600x600mm or Approved Equivalent
Same as item no. 69 but of H & R Johnson(Marbonite), S&P Grey of size 600x600 mm or Approved Equivalent
Same as item no. 69 but of H & R Johnson(Marbonite), Snow Carara of size 900x900 mm or Approved Equivalent
Same as item no. 69 but of H & R Johnson(Marbonite), Olympous of size 600x600 mm or Approved Equivalent
Same as item no. 69 but of NITCO, Novara Beige of size 600x600 mm or Approved Equivalent
Providing and laying minimum 10 mm thick granite tile ofminimum size of 300 mm x 300 mm (Basic rate not lower than Rs. 1000/- per sqm) in flooring of
approved shade and free from cracks, warpage, fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a
bedding of cement mortar 1:5 of average 30 mm thick finishing the joints neatly with white cement mixed with matching colour pigment and finish complete
in all respects and all material and labour complete giving required slope as directed by Engg.-In-Charge.
If necessary, surface unevenness shall be filled up with brick ballast manually compacted with watering etc. complete as per instructions of Engg.-In-Charge
without extra cost.
Providing and laying 10 mm thick white marble (Basic rate not lower than Rs 700/sqm)of size of 1000 mm x 1000 mm in flooring of approved shade and free
from cracks, warpage, fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a bedding of cement mortar
of 30 mm thick CM 1:5 finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect and all material and labour
complete. If necessary, surface unevenness shall be filled up with brick ballast manually compacted with watering etc. complete as per instructions of Engg.-
In-Charge without extra cost.
Bidder's Seal & Signature Page 6 of 37
-
7/31/2019 Rajasthan SOR
7/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
80 KOTA STONE FLOORING / STEPS SquareMetres
530
81 IPS FLOORING SquareMetres
215
82 EUROCON TILE-WALKWAY NLT 500 SquareMetres
960
83 EUROCON TILE-WALKWAY NLT 400 SquareMetres
780
84 CHEQUERED TILES SquareMetres
760
85 SKIRTING RunningMetre
95
86 VITRIFIED TILE SKIRTING NLT 700 RunningMetre
160
87 VITRIFIED TILE SKIRTING NLT 1000 RunningMetre
230
88 POLISHED GRANITE SKIRTING RunningMetre
215
89 POLISHED MARBLE SKIRTING RunningMetre
155
Same as Item No.85 but Marble skiritng (10mm thick) of approved colour and shade.
90 POLISHED KOTA STONE SKIRTING RunningMetre
120
91 CERAMIC TILES DADO IN TOILET SquareMetres
505
92 DESIGNER TILES DADO IN TOILET SquareMetres
715
93 DESIGNER TILES DADO IN TOILET SquareMetres
1175
94 TERRACOTTA TILES SquareMetres
645
Providing and fixing 20 mm thick Kota stone slabs with 25mm bedding CM 1:3, cement slurry and machine polishing on one side. The tiles should be of first
quality and free from cracks, warpage, fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a bedding
of cement mortar 1:5 of average 30 mm thick, finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect with all
material and labour complete, giving required slope as directed by Engg.-In-Charge.
If necessary, surface unevenness shall be filled up with brick ballast, manually compacted with watering etc. complete as per instructions of Engg.-In-Charge
without extra cost. In case of step slabs, one piece slab to be used. The slab shall not have exposed sharp edges. The exposed edges shall be grinded and
polished in smooth curvature.
Providing, mixing and laying 50 mm thick Indian Patent Stone flooring in PCC 1:2:4 mix concrete with 12 mm and down size graded crushed aggregate
including providing and fixing 4 x 25 mm size glass strips in 1 metre x 1 metre panels, casting the concrete compacting and finishing the surface smooth
using cement slurry.
Supply and fixing concrete tile of EUROCON make of approved shade of 20mm thickness for flooring including providing 20mm thick 1:5 cement mortar bed
and a floating coat of neat cement slurry, finishing the joints with white cement mixed with matching colour pigment, cleaning the surface with dilute sulphuric
acid etc. complete. If necessary, surface unevenness shall be filled up with brick ballast manually compacted with watering etc. complete as per instructions
of Engg.-In-Charge without extra cost. Basic rate : Not lower than Rs. 500/sqm.
Same as item no.82 but for treads and risers. Basic rate: Not lower than Rs. 400/sqm
Supply and fixing NITCO make 300x300 mm external Mosaic chequered tiles design No. RY36S of approved shade of 25 mm thickness including providing20mm thick 1:5 cement mortar bed and finishing the joints with white cement mixed with matching colour pigment, cleaning the surface neat etc. complete. If
necessary, surface unevenness shall be filled up with brick ballast manually compacted with watering etc. complete as per instructions of Engg.-In-Charge
without extra cost.
Providing and fixing tile skirting of approved shade and make of First quality free from crack fissures & flakes with straight edges & perfect corners fixed at
right angles of 150 mm height using cement mortar bedding 1:3 and fixed with neat cement slurry and finishing the joint with white cement mixed with
matching colour pigment . Rate to include necessary chipping if required in masonry / concrete, so that skirting is projecting uniformly 6mm from plastered
face. All vertical joints of skirting should match with floor tiles spacing uniformly complete as per direction of EIC.
CERAMIC TILES SKIRTING : Kajaria make of gr. IV (8mm thick).
Same as Item No.85 but Polished vitrified ceramic tile 8mm thick skirting. Basic rate-Not lower than Rs.700/sqm
Same as Item No.85 but Polished vitrified ceramic tile 8mm thick skirting. Basic rate-Not lower than Rs.1000/sqm
Same as Item No.85 but Granite skirting (10mm thick) of approved colour and shade.
Same as Item No.85 but Kota Stone skirting (20mm thick) of approved colour and shade.
Providing and fixing minimum 5 mm thick ceramic tiles of minimum 200 x 100 mm size of approved shade and make First quality, free from crack fissures &
flakes with straight edges & perfect corners fixed at right angles as per the design and pattern required, including applying 12mm thick backing plaster in 1:3
CM and fixing the tiles with neat cement paste and finishing the joints with white cement mixed with colouring pigments to match the colour of tiles properly
cured & finished in all respect.
Designer Tiles with suitable Borders on top and middle; Other specifications same as item no.91
Same as item no. 91 but polished vitrified tiles.Tiles size shall vary between 300x300 mm (minimum) and 600X600 mm (maximum) as directed by Engg.-In-
Charge.
Bidder's Seal & Signature Page 7 of 37
-
7/31/2019 Rajasthan SOR
8/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
95 WALL TILES DADO-RIVIERA SquareMetres
655
96 WALL TILES DADO-BINACO CARARA SquareMetres
655
97 WALL TILES DADO-CREMA ROYALE SquareMetres
655
98 WALL TILES DADO-RECTIFIED SquareMetres
655
99 GRANITE SLAB-18MM GREY SquareMetres
2400
100 SILL SLAB SquareMetres
2525
101 CURTAIN WALL-WITH FIXING LOGO SquareMetres
2375
102 CURTAIN WALL-W/O FIXING LOGO SquareMetres
2325
103WATER PROOFING WITH BITUMEN FELT Square
metres 155
104 WATER PROOFING-BRICKBAT COBA SquareMetres
290
105 ROOF-THERMAL&MOIST. PROTECTION SquareMetres
380
BRICKBAT COBA ON TERRACE Providing and laying integral cement based water proofing of average 100 mm thick as per specifications given. The job
includes cleaning of RCC slab and applying neat cement slurry mixed with water proofing compound, providing and laying brickbat coba in CM 1:4 mixed with
water proofing compound and curing for a period of 24 hours, laying of 25 mm thick PCC 1:1.5:3 mix with 6 mm and down size coarse aggregate and water
proofing compound, finishing smooth, making half round vata at the junction of parapet wall and slab and curing for 10 days.
Same as item no. 95 but Make: H & R Johnson (Marbonite) - Rectified or Approved Equivalent
Providing and fixing not less than 18 mm thick pre polished water cut greygranite slabs over steps or as advised including providing 25mm thick bed cement
mortar 1:4 (1 cement : 4 coarse sand), as per design incl. chamfered edges and polished nosing. Rate includes 8 mm thick polished black granite tile work innosing as per drawing. Job includes finishing the joints with white cement mixed with matching colour pigment.
Providing and laying machine cut and machine polished 18 mm thick jet black granite slab in one piece over a bedding of 20 mm thick 1:5 CM for window
sills. The granite slab shall not have exposed sharp edges. The exposed edges shall be grinded and polished in smooth curvature.
Supply and fixing minimum jet black granite slabs machined cut and polished on curtain wall by providing bedding of cement mortar and neat cement
backing of average 20mm thick in CM 1:3, filling ofinterspaces with black cement so as to match the colour of granite. The slabs shall be preferably cut from
the single rock source to have uniform grain structure free from cracks, fissures and flakes with straight edges and perfect corners.
Water proofing with bitumen felts as per specifications (Bitumen of Shalimar or equivalent make as approved by EIC)- Scrapping, removing old bituminised
surface, if any, by chisel, etc, cleaning the surface thoroughly with wire brush and duster and providing water proofing as per specification. Applying one coat
of bitumen primer, applying hot bitumen 30/40 @ 1.2 kg/SQM. Supplying and laying bitumen felt conforming to IS:1322 in lengths at r ight angles to the
direction of the run of the gradient, starting at the lowest level and overlap of 75 mm for adjacent layers, overlap at end of str ip of felt should be 100mm.
Parapet joints to be suitably fillated and the felto to be taken upto a minimum height of 225mm on the parapet. Scope of job includes breaking of parapet
plaster upto min. 225mm making chases before the felto and finally plastering the surface upto the felto height.
Same as item no.101 but without fixing LOGO: To leave provision for fixing the logo. Granite used shall be minimum 18 mm thick.
The slab should have following minimum dimensions. Width = 0.8 M, Length = 1.2M, Thickness = 18 mm, The slabs have to be fixed by taking services of
highly skilled masons true to plumb complete in all respect. Granite slabs used shall not be more than six nos. In case of increase in no. of slabs prior
approval of Engg.-In-Charge shall be obtained.
With fixing LOGO supplied by HPCL: Including fixing of logo and electrification for the same. Granite used shall be minimum 18 mm thick.
Contractor will be required to submit a guarantee on Rs. 100/- stamp paper for a period of 10 years in respect of performance of waterproofing.
THERMAL & MOISTURE PROTECTION (roof water proofing) : Providing and laying the following roof water proofing treatment consisting of (i) First layer of
50 mm thick CC 1:3:6 over roof slab laid to falls and slope on minimum 1:100 and finished smooth to receive water proofing membrane. (ii) Second layer of
3mm thick polyester reinforced modified bituminous water proofing membrane including primer coat as per manufacturer's specification. (iii) Third layer of 150
micron polythene sheet laid over the water proofing membrane.
(iv) final layer of 25mm thick 600mm x 600mm precast concrete tiles of M-25 grade with 10mm grooves filled up with cold bitumen to form 600x600mm
panels as contraction joints all material and labour complete in all respect. Contractor will be required to submit a guarantee on Rs. 100/- stamp paper for a
period of 10 years in respect of performance of water proofing.
Providing and fixing terracotta tiles minimum 3 mm thick and minimum 75x150 mm size ofapproved shade and make First quality, free from crack fissures &
flakes with straight edges & perfect corners fixed in true line & level as per the design and pattern advised by Engg.-In-Charge. Rate includes applying 12
mm thick backing plaster in 1:3 CM in true line & level, properly cured & rough finished. Fixing the tiles with neat cement paste and finishing the joints with
terracotta paint in a neat & aesthetic way complete in all respects. Approved Make of Tiles: Dazzle Designer Tiles of Milan - Terracotta smooth finish
WALL TILES DADO: Providing and fixing minimum 5 mm thick wall tiles of approved shade, gloss and finish of size 600 x 300 mm size of approved shade
and make First quality, free from crack fissures & flakes with straight edges & perfect corners fixed at right angles as per the approved design and pattern
required, including applying 12mm thick backing plaster in 1:3 CM and fixing the tiles with neat cement paste and finishing the joints with white cement mixedwith colouring pigments to match the colour of tiles properly cured & finished in all respect.
Make: H & R Johnson (Marbonite) - Riviera or Approved Equivalent
Same as item no. 95 but Make: H & R Johnson (Marbonite) - Binaco Carara or Approved Equivalent
Same as item no. 95 but Make: H & R Johnson (Marbonite) - Crema Royale Approved Equivalent
Bidder's Seal & Signature Page 8 of 37
-
7/31/2019 Rajasthan SOR
9/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
106 KERB BLOCKS 300x140x230mm RunningMetre
120
107 KERB BLOCKS 300x140x300mm RunningMetre
150
108 KERB BLOCKS 200x100x400mm RunningMetre
120
109 KERB BLOCKS 200x150x300mm RunningMetre
135
110 KERB BLOCKS 250x150x450mm RunningMetre
255
111 PAINTING WORKS-WHITEWASH SquareMetres
7
112 APEX PAINTING SquareMetres
90
113 OIL BOUND DISTEMPER SquareMetres
43
114 ACRYLIC EMLUSION PAINT-INTERIOR SquareMetres
64
Providing and fixing at or near ground level smooth finished pre-cast, cement concrete blocks in kerbs, edging etc. The block may be precast at site or any
other approved place in PCC 1:1.5:3 using steel mould in approved pattern and setting. The blocks shall be laid / fixed in posit ion using CM 1:3. The job
includes machine mixing, use of vibrator, all labour, material laying etc complete. If directed excavation upto 200 mm shall be carried out without any extra
cost. Kerb block of approx 300x140x230mm size. (length x thickness x height). The face corner of the kerb block will be made rounded as per instructions.
Same as item no. 106 but Kerb block of approx 300x140x300mm size. (length x thickness x height).
Same as item no.106 but Kerb block of approx 200x100x400mm size. (length x thickness x height).
Same as item no. 106 but Kerb block of approx 200x150x300mm size. (length x thickness x height).
Same as item no.106 but Kerb block of approx250x150x450mm size. (length x thickness x height). Every fifth block shall have115x95x40 mm cavity as per
approved drawing with retroreflective red paint making the spacing of such painted cavities @ 1 m C/C.
All material required for execution of painting work shall be obtained direct from approved manufacturers and shall be brought to the sites in their drums /
cans / bags etc with seals unbroken. No thinner shall be used unless approved by Engg.-In-Charge. The paint shall be applied by using brush, roller or
spraying as directed. The paint etc shall be applied only after proper surface preparation by removing all dirt, dust, mortar droppings, another foreign matter,loose scale by using brooms, wire brush, sand paper etc as per requirement and direction complete.
All holes, cracks, patches etc shall be made good with material similar to that ofthe surface. The painting shall be applied in specified coats or more so as to
obtain the desired finish. If additional coats are required to obtain uniform and smooth finish, the same shall be carried out at no extra cost. The job includes
provision of scaffolding using safety precautions, curing etc as required.
WHITEWASH : Providing and applying 3 coats of white wash to plastered and concrete surfaces by mixing binder, glue, indigo etc. complete as per IS: 712-
Latest Edition.
APEX PAINTING : Providing and applying 2 coats of Apex paint to all the exterior surfaces including a coat of primer as per manufacturer's specification
complete. General specifications/guidelines given under WHITEWASH item also to be followed, as applicable.
OIL BOUND DISTEMPER Providing and applying 2 coats ( f irst coat with brush and final coat with Roller) of OBD of approved make and shade on all
surfaces and heights to give an even shade including priming coat and compatible putty etc. complete. General specifications/guidelines given under
WHITEWASH item also to be followed, as applicable.
ACRYLIC EMULSION PAINT (INTERIOR GRADE) Providing and applying 2 coats ( first coat with brush and final coat with Roller) of Acrylic Emulsion paint
of approved make and shade on all surfaces and heights to give an even shade including primer and compatible putty. General specifications / guidelines
given under item no. 111 also to be followed, as applicable.
Bidder's Seal & Signature Page 9 of 37
-
7/31/2019 Rajasthan SOR
10/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
115 ECONOMY EMLUSION PAINT-INTERIOR SquareMetres
42
116 ACRYLIC EMULSION PAINT-EXTERIOR SquareMetres
70
117 WATER PROOF CEMENT PAINT SquareMetres
38
118 SANDTEX MATT PAINT SquareMetres
70
119 SYNTHETIC ENAMEL PAINT-WALL SquareMetres
60
120 SYNTHETIC ENAMEL PAINT-STEEL SquareMetres 65
121 SYNTHETIC ENAMEL PAINT-WOOD SquareMetres
70
122 PLASTIC EMULSION PAINT SquareMetres
64
123 POP - WALL, BEAM, COLUMN & CEILING Square
Metres
55
124 POP - MOULDING RunningMetre
85
125 FLUSH DOOR 34 MM THICK SquareMetres 1750
Providing and applying 2 coats ( first coat with brush and final coat with Roller) of approved shade Economy Emulsion (Bison Super Emulsion of Beger or
approved equivalent) paint on all surfaces and heights to give an even shade including primer and compatible putty. General specifications / guidelines given
under item no.111 also to be followed, as applicable.
ACRYLIC EMULSION PAINT (EXTERIOR GRADE) Providing and applying 3 coats of acrylic anti fungal cement paint including primer of BERGER
(Weathercoat) or approved equivalent make and shade to all the exterior surfaces as per manufacturer's specifications. General specifications / guidelines
given under item no.111 also to be followed, as applicable.
WATER PROOF CEMENT PAINT Providing and applying 2 coats of water proof cement paint of SNOWCEM INDIA make and of required shades on all
surfaces and heights to give an even shade. General specifications / guidelines given under item no.111 also to be followed, as applicable.
SANDTEX MATT Providing and applying 2 coats of Sandtex matt paint of SNOWCEM INDIA make and of required shades on all surfaces and heights to
give an even shade including primer coat of snowcem plus. General specifications / guidelines given under item no.111 also to be followed, as applicable.
SYNTHETIC ENAMEL PAINT OVER WALL Providing and applying 2 coats of synthetic enamel paint 1st quality of approved manufacturer and of required
shades on wall to give an even shade including a primer coat. General specifications / guidelines given under WHITE WASH item also to be followed, as
applicable.
SYNTHETIC ENAMEL PAINT OVER STEEL SURFACE Providing and applying 2 coats of synthetic enamel paint 1st quality of approved manufacturer and
shades on steel surface to give an even shade including two coats of red oxide primer. General specifications / guidelines given under item no.111 also to be
followed, as applicable.
Supply and fixing termite resistant ISI marked prelaminated solid core type wooden flush doors as per IS:2202, Part-1:1999 (Plywood face panels) finished
with 1mm thick laminates of approved colour / pattern on both sides and of total thickness not less than 34 mm. Both side faces and all the edges shall be
polished in approved colour / pattern as per directions of EIC.
Rate shall be inclusive of all labour, fixing the door in frame in true plumb, line and level & supply and fixing heavy duty 3 nos. stainless steel (SS) hinges of
100 mm length, 2 nos. SS aldrops of 200 mm length one from inside and other from outside, SS tower bolt of 200 mm length and door stopper etc. al l
complete. Approved Make: Kitply / Anchor Board / Wonder wood / Duro / National or equivalent. Teak wood door frame will be paid for separately as per
relevant item.
SYNTHETIC ENAMEL PAINT OVER WOOD WORK Providing and applying 2 coats of synthetic enamel paint 1st quality of approved manufacturer and
shades on wood surface including a coat of primer to give an even shade. General specifications / guidelines given under item no.111 also to be followed, as
applicable.
PLASTIC EMULSION PAINT: Providing and applying 2 coats ( first coat with brush and final coat with Roller) of Plastic Emulsion paint of approved make
and shade on all surfaces and heights to give an even shade including primer and compatible putty. Approved Make: Asian/Nitco / Nerolac. General
specifications / guidelines given under item no.111 also to be followed, as applicable.
ON WALL & CEILING: Providing and applying Plaster of Paris (POP) punning on walls, ceilings, beams and columns to bring the surface in plumb line and
level including making the surface smooth etc. complete. The rate shall include preparing the surface with POP and compatible putty to give a smooth finish
as per approval of the Engg.-In-Charge. Rate to include cost of scrapping, neeru finish etc. complete if needed.
Plaster of Paris (POP) Moulding : Providing and fixing moulding of size 3" x 3" in the edge of the wall and the ceiling with necessary hardware, properly
finished, all material and labour complete.
Bidder's Seal & Signature Page 10 of 37
-
7/31/2019 Rajasthan SOR
11/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
126 TEAK WOOD DOOR FRAME RunningMetre
550
127 ANODISED ALUMINIUM GLAZING DOOR-12MM GLASS SquareMetres
2800
128 ALUMINIUM GLAZING DOOR-12MM TOUGHENED GLASS SquareMetres
4500
129 POWDER COATED ALUMINIUM GLAZING DOOR-12mm SquareMetres 2875
130 POWDER COATED ALUMINIUM GLAZING DOOR-TOUGHENED SquareMetres
4575
131 ANODISED ALUMINIUM FIXED GLAZING-12MM GLASS SquareMetres
2800
132 ALUMINIUM GLAZING FIXED-12MM TOUGHENED GLASS SquareMetres
4500
133 POWDER COATED ALUMINIUM GLAZING FIXED GLAZING-12MM SquareMetres
2875
134 POWDER COATED ALUMINIUM GLAZING FIXED-TOUGHENED SquareMetres
4575
135 HYDRAULIC FLOOR SPRINGS Each 1450
136 ALUMINIUM PANELED DOOR-PARTICLE BOARD SquareMetres
2600
ALUMINIUM GLAZED DOOR WITH 12MM GLASS: Providing and fixing Aluminium glazed door with 15 micron coloured anodised aluminium section with
extruded built up section of approved make and weight ratio joints mitred joint with heavy duty aluminium pressure die cast cleats with fins to match the
section of frames conforming to approved section and shutter conforming to approved section and glazed with12 mm thick glass fixed to shutter with neoprin /
PVC gasket / CP brass / Stainless steel screws or with fixing clips or with expansion hold fasteners with requisite PVC / Neoprin felt / polysulphide sealant /
silicon sealant etc. complete as per architectural drawing and instruction of Engg.-In-Charge.
Supply and fixing seasoned (IS:1141-1993 latest edition) pretreated (IS:401-2001 latest edition) teak wood frame for flush door installation and of 125X63
mm nominal cross section. The timber will be sound, straight and free from sap, radial cracks, decay, fungal growth, boxed heart, pitch pockets, borer holes,
splits, loose knots, rots or any other flaws. Rates are inclusive of 25X10 mm teakwood beading of same specification and matching colour polish covering
junction of frame and wall in true line, level and finish.
Rate to include all labour, carpentry, making chases, grooves, polish and provision of 6nos. M.S.holdfast 25x4X230mm per frame with nuts and bolts as
required and grouted in situ in concrete blocks of mix 1:2:4 and of size as directed. For concrete surfaces, 12mm diameter counter sunk anchor bolts or
coarch screws shall be used for fixing of all door frames, finishing the frames with putty and two coats of approved matching polish / enamel paint. Inner
surface of teak wood frame shall be coated with anti-termite solution etc. all complete.
ALUMINIUM FIXED GLAZING WITH 12MM GLASS: Providing and fixing Aluminium fixed glazing with 15 micron coloured anodised aluminium section
minimum wall thickness of not less than 2 mm with extruded built up section of approved make and weight ratio joints mitred joint with heavy duty aluminium
pressure die cast cleats with fins to match the section of frames conforming to approved section and glazed with 12 mm thick glass fixed with Al snap
beading and neoprin / PVC gasket / CP brass / Stainless steel screw and fixed to the wall with rawl plugs and screws or with fixing clips or with expansion
hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with requisite PVC / Neoprin felt / polysulphide sealant / silicon
sealant etc complete as per architectural drawing and instructions of Engg.-In-Charge.
Al anodised shop front fixed glazing with frames at top and bottom of HINDALCO make section no. SP-2670 of size 88X42X2.3 with weight of2.927 kg/m or
approved equivalent and at two side ends of HINDALCO make section no. SP-730 of size 63.5X38X3 with weight of 1.55 kg/m or approved equivalent and
fixing cleats / clips of HINDALCO make section no. SP-1778 of size 17.15x17.27x1.4 with weight 0.175 kg/m without any intermediate vertical aluminium
sections at joints. The intermediate vertical joints spacing in glass shall not be less than 3 m C/C and no horizontal joints shall be permitted in glass. The
vertical joints shall be finished smooth having machine cut glass edges in true plumb, line and level. The joint shall be treated with silicon sealant to stop
water ingress and glass surfaces shall be cleaned neat of left over sealant. Prior approval of HPCL Engg.-In-Charge shall be obtained if spacing of vertical
joints is needed to be less than 3 m C/C. Approved Make of Glass: AIS, Modi, Saint Gobain, Triveni. In case of non-availability, approved equivalent make for
Al sections is JINDAL.
Approval of Engg.-In-Charge shall be taken before using equivalent sections matching next higher dimensions and weight per running metre without extra
cost.
Al anodised shop front doors with frames at top and bottom (without any vertical aluminium section) of HINDALCO make - section no. SP-2670 of size
88X42X2.3 with weight of 2.927 kg/m for door top and bottom, round acrylic handle using CP brass / Stainless steel screws. The glass should be single
piece only. All glass edges shall be grinded and polished smooth as per instructions. The floor spring strut shall be fixed and accommodated in Aluminium
section groove. In case of non-availability, approved equivalent make for Al sections is JINDAL. Approval of Engg.-In-Charge shall be taken before using
equivalent sections matching next higher dimensions and weight per running metre without extra cost. Approved Make of Glass: AIS, Modi, Saint Gobain,
Triveni.
With 12 mm toughened glass with all specification as item no.127
With Powder Coated Aluminum section of approved colour having coating thickness of minimum 50 micron with 12mm plain glass and all specification as
item no. 127 Anodisation shall not be done.
With Powder Coated aluminum section of approved colour having coating thickness of minimum 50 micron with 12mm toughened glass and all specification
item no. 127. Anodisation shall not be done.
With 12 mm toughened glass with all specification as item no.131
With Powder Coated Al section with 12mm plain glass and all specification as item no.131 Anodisation shall not be done.
With Powder Coated Al section with 12mm toughened glass and all specification as item no.131. Anodisation shall not be done.
HYDRAULIC FLOOR SPRINGS Providing and fixing double action hydraulic floor springs of approved brand ( HARDWYN / EVERITE / SANDHU)
conforming to IS:6315-1992 for aluminium doors. Rate to include cutting of floors as required, embedding in floors and cover plates etc complete as per
specifications. Load Capacity = 61-80 kg.
Bidder's Seal & Signature Page 11 of 37
-
7/31/2019 Rajasthan SOR
12/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
137 ALUMINIUM PANELED DOOR-BISON LAM SquareMetres
2600
138 ALUMINIUM WINDOWS (OPENABLE) SquareMetres
2150
139 ALUMINIUM WINDOWS SLIDING- 2 TRACK SquareMetres
2450
140 ALUMINIUM WINDOWS SLIDING- 3 TRACK SquareMetres
2450
141 ALUMINIUM LOUVERED VENTILATOR SquareMetres
2600
ALUMINIUM PANELED DOOR : Providing and fixing 15 micron colored anodised single leaf aluminium door with minimum wall thickness of not less than 2
mm, joints mitred and jointed with heavy duty aluminium pressure die cast cleats with fins to match the outer frames and door frames conforming JINDAL
sections as specified fully paneled with 9 mm thick pre-laminated 3 layers medium density (exterior grade) particle board Grade-1, type -II conforming to
IS:12823 bonded with phenolformaldehyde synthetic resin of approved brand and manufacturer fixed to shutter with aluminium snap beading and neoprene /
PVC gasket / CP Brass / stainless steel screws fixed to the wall with requisite
rawl plugs and screw or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with
requisite PVC / neoprene felt / polysulphide sealant / silicon sealant including hard ware such as tower bolt of 150 mm length from inside and Aluminum
handle and Aluminum aldrop of 200 mm length
on both sides, 3 nos. Aluminium hinges of 100 mm length etc all complete as per architectural drawing. Aluminium door section of JINDAL make or
equivalent make with the following section: Main frame on al l s ides - 4700 -101.6 x 44.45 x 2.5 of weight 1.977 kg/m, Shutter vert ical frame- 4537 -53.7x44.45x2.3 of weight 1.238 kg/m. Shutter top frame - 4540 - 53.7x44.45x2.3 of weight 1.173 kg/m.
Shutter middle frame - 4621 - 49.91x44.45x3 of weight 1.495 kg/m Shutter bottom frame - 4524 -83.5x44.45x3 of weight 2.107 kg/m, aluminium Cast Door
handle and Clip - 4420 - 19x17.3x0.9 of weight 0.124 kg/m. In case of non-availability, approved equivalent make for Al sections is HINDALCO. Approval of
Engg.-In-Charge shall be taken before using equivalent sections matching next higher dimensions and weight per running metre without extra cost.
Providing and fixing aluminium door to concrete and brick work using 9 mm thick Pre laminated both side Bison lam sheet (Cement particle Board) instead of
particle board fixed to shutter. Rest of the specifications same as item no. 136 as applicable.
ALUMINIUM WINDOWS (OPENABLE) : Providing and fixing 15 micron colour anodised aluminium glazed windows with 5 mm glass & extruded built up
section ofwall thickness not less than 1.4 mm and approved make with glass panel fixed to side -hung shutter with aluminium snap beading and neoprene
/ PVC gasket / CP Brass / stainless steel screws fixed to the wall with requisite rawl plugs and screw or with fixing clips or with expansion hold fasteners
including necessary filling up of gaps at junctions at top, bottom and sides with requisite PVC / neoprene felt / polysulphide sealant / silicon sealant including
heavy duty handle cum locking arrangement etc all complete as per architectural drawing and the direction of Engg.In-charge.
Aluminium door section of JINDAL make or equivalent make with the following sections : Outer frame - 8804 of weight 0.622 Kg/m, Shutter frame- 8802 of
weight 0.575 kg/m; Mullion - 8803 of weight 0.729 kg/m; Cleat angle (HIDALCO make) A-3350 - 38x25x3 of weight 0.490 kg/m; Glazing clip - 4433 of
weight 0.137 kg/m. Approved Make of Glass : AIS, Modi, Saint Gobain, Triveni. In case of non-availability, approved equivalent make for Al sections is
HINDALCO. Approval of Engg.-In-Charge shall be taken before using equivalent sections matching next higher dimensions and weight per running metre
without extra cost.
Same as above item no.138 but Aluminium sliding windows of Jindal make shutter sections: Top & Bottom - 8820- 1.5 mm thick @ 0.547 kg/m; Handle
Section 8822- 1.5 mm thick @ 0.547 kg/m; Shutter Interlock 8821- 1.45 mm thick @ 0.607 kg/m. Rate includes wheels / bearings, in terlocking
arrangements etc. complete. The track section shall be as follows:
Two Track Window: Top & Side - 8931-1.5 mm thick @ 0.784 kg/m; Bottom (Bulb) - 8932- 1.5 mm thick @ 0.909 kg/m
Same as Item No.138 but Three Track Window: Top & Side - 8933-1.5 mm thick @ 1.06 kg/m; Bottom (Bulb) - 8934- 1.5 mm thick @ 1.248 kg/m
ALUMINIUM LOUVERED VENTILATOR: Providing and fixing 15 micron colour anodised aluminium ventilator with extruded built up section of wall thickness
not less than 1.5 mm and approved make glazed with 5 mm thick opaque glass louver 100mm wide.
Bidder's Seal & Signature Page 12 of 37
-
7/31/2019 Rajasthan SOR
13/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
142 ALUMINIUM DOOR / FIXED GLAZING - 6 MM GLASS SquareMetres
2400
143 STEEL WINDOWS SquareMetres
2260
144 STEEL DOORS SquareMetres
1775
145 ROLLING SHUTTER SquareMetres
1775
146 GRILL IN ROLLING SHUTTER SquareMetres
1900
147 DISPLAY SHELF SquareMetres 3225
148 DISPLAY SHELF - BOTTOM STORAGE SquareMetres
3950
ALUMINIUM DOOR / FIXED GLAZING WITH 6 MM GLASS: Providing and fixing 15 micron coloured anodised aluminium fixed glazing / aluminium door
with 6 mm glass extruded built up section of wall thickness not less than 1.5 mm and approve make with glass panel fixed with Aluminium snap beading /
Neoprene / PVC gasket / CP Brass / stainless steel screws and fixed to thewall with requisite rawl plugs and screw orwith fixing clips or with expansion hold
fasteners including necessary fi ll ing up of gaps at junctions, at top, bottom and sides with requisite PVC / neoprene felt / polysulphide sealant / sil icon
sealant all complete as per architectural drawing and the direction of Engg. In-charge.
Aluminium section of JINDAL make or equivalent make with the following sections :
Fixed Glazing:
Outer frame sections - 4688- 63.5x38.1x1.65 of weight 0.942 kg/m.
Intermediate frame - 4687- 63.5x38.1x1.53 of weight 0.942 kg/m.
Glass panels used shall not be less than 2.4 m (height) x 1.2 m (width). All the joints shall be provided with Aluminium sections as specified.
Door:
Outer side frame - 4550 - 47.62x44.45x1.52 of weight 0.881 kg/m.
Bottom frame - 4553 - 95.25x44.45x1.70 of weight 1.301 kg/m
Intermediate frame - 4621- 49.91x44.45x1.60 of weight 0.882 kg/m.
Clip- 4420- 19x17.3x0.9 of wt. 0.124 Kg/m.
Hood Covers: MS sheet of 0.9 mm thick Locking handle : To be provided suitably. Rate shall include providing and fixing holdfasts and painting two coats of
enamel paint of approved make and shade over two coats of zinc phosphate primer. Shutter up to 10 SQM -push pull type hand operated with ball bearings,
For 10 SQM upto 30 SQM- Mechanical operated gear type with ball bearing, a pulling hook shall be provided for each of the rolling shutter.
GRILL IN ROLLING SHUTTER: Supply, fabrication and fixing of manually operated steel rolling net shutter as per the specification. Nets to be in hexagonal
pattern, The round MS bars used for jali should be 8mm in dia. All other specification as item no. 145
DISPLAY SHELF: Providing & fixing in posit ion 12 mm thick plain glass of Modi / AIS / Saint Gobain / Triveni make with polished edges in the grooves
between the 25 mm thick exterior grade MDF board planks at 325 mm C/C & 350 mm wide. The MDF board shall be fixed on teak wood frame fixed to the
wall using plugs, screws and holdtights. Cross section of teak wood shall be 50x75 mm. The teak wood shall be seasoned and brushed with anti-termite
chemical before use. Teak wood framing shall be fixed over wall in such a way that it forms grids of size 450x325 mm so as not to obstruct the grooves. The
exposed surface of the MDF board shall be finished with 1.5 mm thick lamination of approved colour & combination of colours with teak wood beadings on
edges. The approved brand for the lamination shall be Formica / Greenlam / Sundek.
The floor spring strut shall be fixed and accommodated in Aluminium section groove. The door shall be provided with die cast aluminium handle, towerbolt,
locking arrangement etc. complete. The joints and gaps shall be treated with silicon sealant to stop water ingress and glass surfaces shall be cleaned neat of
left over sealant. Approved Make of Glass: AIS, Modi, Saint Gobain, Triveni. In case of non-availability, approved equivalent make for Al sections is JINDAL.
Approval of Engg.-In-Charge shall be taken before using equivalents matching next higher dimensions and weight per running metre without extra cost.
STEEL WINDOWS : Supply, fabrication and fixing of MS glazed windows using approved Z sections with 5mm plain glass including providing grill with
12mm square bar @100mm C/C, painting with two coats of red oxide primer and two coats of synthetic enamel paint, handle, stay arrangement etc.
complete.
STEEL DOORS: Supply, fabrication and fixing of MS Door using 35x35x5 angle frame and 25x25x3 angle members including bracings with 16 gauge MS
sheet stitch welded to Door shutter frame complete as per direction of Engg.-In-Charge painting with two coats of red oxide primer and two coats of synthetic
enamel paint, handle, stay arrangement, tower bolt etc. complete.
ROLLING SHUTTER Supply, fabrication and fixing of MS rolling shutter of the following specifications including grill window of 300 mm height at eye level for
visibility even in closed position. Code: Conforming to IS:62481979 Type: Self Coiling type (manual) Curtains: Interlocking cold rolled lath section of 0.8 mm
thickness. Lock plate: MS sheet of 3.15 mm thick reinforced with MS angles of35 x 35 mm. Guide channel : MS sheets of3.5 mm thick Bracket Plate : MS
Sheet of 0.9 mm thick.
Specifications as item no. 147 but with storage at bottom, as per enclosed drawing.
Bidder's Seal & Signature Page 13 of 37
-
7/31/2019 Rajasthan SOR
14/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
149 FAN HOOKS Each 40
150 MORTICE LOCK Each 870
151 DOOR CLOSER Each 1000
152 STRUCTURAL STEEL WORK-SERVICE BAY Metric Ton 44500
153 S/I/F CORUGATED ASBESTOS SHEET-ROOF SquareMetres
345
154 S/I/F CORRUGATED ASBESTOS SHEET-GABLE SquareMetres
400
15520 gauge (1.0 MM) sheets Square
metres 310
15622 gauge (0.8 MM) sheets Square
metres 290
157 GYPSUM BOARD FALSE CEILING SquareMetres
600
158 ACOUSTICAL SUSPENDED CEILING BUTT.. SquareMetres
625
GI SHEET ROOFING: Supplying and fixing corrugated GI sheet roofing of approved make and following thicknesses with GI 'J' or 'L' hooks 10mm dia; GI
limpet and bitumen washer complete. Rate to exclude purlins, rafters, trusses etc, which shall paid under separate head.
Same as item No: 155 but for 22 gauge
FAN HOOKS : Providing & fixing MS fan hooks with 16 mm dia MS bar bent to shape with hooked ends in RCC Slab during laying including painting the
exposed portion.
MORTICE LOCK: Providing & fixing GODREJ make only six lever lock (Cylindrical / Round Head) including all necessary hardware etc.
DOOR CLOSER Providing and fixing door closer of Hardwyn / Everite make size no. 2.
Supplying, erecting and fixing in position Pre- fabricated structures at all elevations for service bay using structural steel sections conforming to IS:2062 ,
including cutting, welding or bolting, supply of bolts / nuts / washers etc., complete as per drawings including surface preparation and applying one coat of
Zinc Phosphate Primer before erection and two coats of synthetic enamel paint as per specification after erection and all materials and labour complete. (No
welding is permitted at site).
The rate quoted shall include cost of bolts, nuts, washers, welding and electrodes and any other consumables required for completing the work. The bolts,
nuts, washers, welds etc. shall not be separately measured and paid for.
Supply, erection and fixing of corrugated asbestos cement sheet of Everest make or approved equivalent for service bay including supply and fixing of
bitumen / GI washer, J bolt etc. For Roof
Same as Item No.153 but for side sheet including gable end.
Providing and fixing Gypsum board false ceiling with required accessories INDIA GYPSUM make including painting with two coats of plastic emulsion paint,
12.5 mm thick 'Gypboard' shall be screw-fixed to the underside of suspended GI grid. GI grid shall be installed as per manufacturer's specifications. GI grid
shall consist of ceiling sections (India Gypsum Code no. MF5) at maximum C/C distance 450 mm, Perimeter channel (India Gypsum code no. MF6A),
intermediate channels (India Gypsum code no. MF7) at maximum C/C distance 1200 mm.
The ceiling sections should be fixed to intermediate channels with connecting clips (India Gypsum code no. ME9). GI grid shall be fixed to RCC slab above
with the help of 25x0.5 mm strap hanger (India Gypsum code no. MF 8) and soffit cleat (India Gypsum code no. P534). The joints between soffit cleat andstrap hanger and GI grid & strap hanger shall be with 6.4x12.7 mm nut and bolt (India Gypsum code no. P526). Soffit cleat shall be fixed to RCC ceiling with
W.E. type 12 mm dia, 17/16" long steel rawl plug. Maximum C/C distance (both ways) ofstrap hangers shall be 1200 m. The Gypboard shall be fixed fixed to
GI grid with 25 mm long drawall screws. The Gypboard to be used shall be 12.5 mm thick tapered edge boards. The boards shall be taped & filled from
underside to ceiling.
The rate shall be inclusive of additional ceiling sections and intermediate channels shall be provided at openings for light fixtures, AC ducts, vertical drops,
offsets etc. Additional intermediate channels shall be fixed to strap hangers at every 1200 mm for additional support to prevent strap hangers from buckling /
swaying. Item to be completed in all respect including necessary sleeves for ducts, finishing of joint cut outs, supports for AC grills, light fixtures, speakers etc.
complete as per directions of Engg.-In-Charge.
Providing & Fixing of Armstrong Acoustical Suspended Ceiling System with Fissured Tiles having Tegular edges. The tiles should have Humidity Resistance
of 90% RH, Average NRC .50, Light Reflectance >80%, Thermal Conductivity k = 0.052 0.057 w/mc, Colo ur White, Fire Performance Class 0/Class 1 (BS
476) in module size of 600mm x 600mm x 15mm laid on 24XL - Hot Dipped Galvanised steel suspension System having rotary stitching on the Main
Runner, 1200 mm & 600 mm Cross Tees.
INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the structural socket by approved hanger at 1200mm maximum
centre. The last hanger at the end of each main runner should not be greater than 450mm from the adjacent wall.
Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross
tees.
Perimeter trim to be Armstrong wall angles or channel, secured to walls at 450 mm max. C/C
For fissured RH 90 Butt Edge.
Bidder's Seal & Signature Page 14 of 37
-
7/31/2019 Rajasthan SOR
15/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
159 ACOUSTICAL SUSPENDED CEILING TEGULR SquareMetres
660
160 WATER CLOSET-EUROPN, COLOURED Each 7800
161 WATER CLOSET-EUROPEAN WHITE Each 5300
162 WATER CLOSETS-INDIAN, COLOURED Each 3250
163 WATER CLOSETS-INDIAN, WHITE Each 2400
164 URINALS - COLOURED Each 1650
165 URINAL-NEW MAGNUM WHITE Each 2400
Providing & Fixing of Armstrong Acoustical Suspended Ceiling System with Fissured Tiles having Tegular edges. The tiles should have Humidity Resistance
of 90% RH, Average NRC .50, Light Reflectance >80%, Thermal Conductivity k = 0.052 0.057 w/mc, Colo ur White, Fire Performance Class 0/Class 1 (BS
476) in module size of 600mm x 600mm x 15mm laid on 24XL - Hot Dipped Galvanised steel suspension System having rotary stitching on the Main
Runner, 1200 mm & 600 mm Cross Tees.
INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the structural socket by approved hanger at 1200mm maximum
centre. The last hanger at the end of each main runner should not be greater than 450mm from the adjacent wall.
Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than
600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross
tees.
Perimeter trim to be Armstrong wall angles or channel, secured to walls at 450 mm max. C/C
For fissured RH 90 Tegular Edge.
EUROPEAN TYPE Supplying and fixing approved colour (pastel colour) wall mounted vitreous china European type water closet comprising of the following
accessories including cutting and making good the walls & floors wherever required complete as directed by Engg.-In-Charge, having following (A) Coloured
(pastel colour) vitreous china European water closet with P or S trap of Parryware make Cascade series No. 0219 having integral matching colour vitreous
china cistern supplied as part of the closet with all mechanisms, with necessary fittings, brackets, screws, etc all complete as per the direction of Engg.-In-
Charge.
(B) 15mm NB CP brass angle valve of approved brand as per the direction of Engg.-In-Charge (C) 15 mm NB CP brss inlet connection with Brass unions at
the ends. (D) Parryware / Commander make or equivalent matching colour polypropylene seat cover with necessary brass hinges and rubber bushes etc (E)
WC connector with neoprene rubber etc. Approved Equivalent - Hindware 20028 with matching colour Vitreous China cistern with all mechanisms, fittings
etc. complete.
EUROPEAN TYPE Supplying and fixing white wall mounted vitreous china European type water closet comprising of the following accessories including
cutting and making good the walls & floors wherever required complete as directed by Engg.-In-Charge, having following (A) White vitreous china European
water closet with P or S trap of Parryware make Cascade series No. 0219 having integral matching colour vitreous china cistern supplied as part of the closet
with all mechanisms, with necessary fittings, brackets, screws, etc all complete as per the direction of Engg.-In-Charge.
(B) 15mm NB CP brass angle valve of approved brand as per the direction of Engg.-In-Charge (C) 15 mm NB CP brss inlet connection with Brass unions at
the ends. (D) Parryware / Commander make or equivalent matching colour polypropylene seat cover with necessary brass hinges and rubber bushes etc
(E) WC connector with neoprene rubber etc. Approved Equivalent - Hindware 20028 with matching colour Vitreous China cistern with all mechanisms, fittings
etc. complete.
INDIAN WATER CLOSET Supplying and fixing approved colour (pastel colour) vitreous china Orissa Pan type water closet comprising of the following
accessories including cutting and making good the walls & floors wherever required complete as directed by Engg.-In-Charge ( A) Coloured (pastel colour)
vitreous china 580 mm size water closet of Parryware Cat. 0109/17 with P or S trap (B) 10 litre capacity hi-grade engineering plastic low level flushing cistern
of matching colour Cat. - 0709 of Parryware with necessary fittings, brackets , screws etc. all complete.
(C) 32 mm CP brass flush pipe of approved length with necessary fittings, clamps etc. (D) 15 mm NB CP inlet connections with brass union at the ends. (E)
15mm NB CP brass angle valve of approved brand as per the direction of Engg.-In-Charge (F) WC connector with neoprene rubber. Approved Equiv. -
Hindware Cat. 20004 with equivalent low level cistern
INDIAN WATER CLOSET Supplying and fixing white vitreous china Orissa Pan type water closet comprising of the following accessories including cuttingand making good the walls & floors wherever required complete as directed by Engg.-In-Charge ( A) White vitreous china 580 mm size water closet of
Parryware Cat. 0109/17 with P or S trap (B) 10 litre capacity hi-grade engineering plastic low level flushing cistern of matching colour Cat. - 0709 of Parryware
with necessary fittings, brackets, screws etc. all complete.
(C) 32 mm CP brass flush pipe of approved length with necessary fittings, clamps etc. (D) 15 mm NB CP inlet connections with brass union at the ends. (E)
15mm NB CP brass angle valve of approved brand as per the direction of Engg.-In-Charge (F) WC connector with neoprene rubber. Approved Equiv. -
Hindware Cat. 20004 with equivalent low level cistern.
Supplying and fixing coloured (pastel colours) vitreous china flat back urinal of size 300mmx400mm with integrated overflow of Hindustan Sanitary or
equivalent approved make with CP flush valve, CP pipe connection, CP waste coupling, CP Brass bottle trap, 32 mm PVC waste line ofrequired length etc.
all complete as per the direction of Engg .-In-Charge.
Supplying and fixing WHITE vitreous china urinal of Parryware make New Magnum Series No. 0575, CP flush valve, CP pipe connection, CP waste coupling
, CP Brass bottle trap, 32 mm PVC waste line of required length etc. all complete as per the direction of Engg.-In-Charge. Approved Equivalent - Hindware
60006 Olympous half stall.
Bidder's Seal & Signature Page 15 of 37
-
7/31/2019 Rajasthan SOR
16/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
166 URINAL-NEW MAGNUM COLOURED Each 3100
167 URINAL-PARRYWARE WITH IN BUILT SENSOR Each 14000
168 URINAL SENSOR-SENSOTRONIC Each 8500
169 SENSOR FAUCET-WASH BASIN Each 14000
170 SENSOR FAUCET-URINAL Each 14000
171 URINAL DIVISION PLATE Each 1450
172HAND WASH BASIN W/O PEDESTAL Each
2250
173 HAND WASH BASIN WITH PEDESTAL Each 2750
174 OVAL BELOW COUNTERBASIN-WHITE Each 1200
175 OVAL BELOW COUNTERBASIN-COLOUR Each 1550
176 WALL HUNG BASIN & PEDESTAL Each 1575
177 MIRROR - 5.5 MM THICK SquareMetres
1800
178 MIRROR- 600X600X5.5 MM Each 650
179 SOAP TRAY Each 130
180 LIQUID SOAP DISPENSER Each 650
181 TOILET PAPER HOLDER Each 135
Supplying and fixing PASTEL COLOURED vitreous china urinal of Parryware make New Magnum Series No. 0575, CP flush valve, CP pipe connection, CP
waste coupling, CP Brass bottle trap, 32 mm PVC waste line of required length etc. all complete as per the direction of Engg.-In-Charge. Approved
Equivalent - Hindware 60006 Olympous half stall.
Supply, installation and commissioning all complete Jaquar make Sensotronic Concealed type Flushing system (Model 51087 - Chrome) including all
accessories, all connections, electricals etc. all complete as per the direction of Engg.-In-Charge.
Supply, installation and commissioning all complete SENSOR FAUCET FOR WASH BASIN WITH 190MM LONG SPOUT (WALL Mounted Model SNR-
51071 Chrome, Make - Jaquar) complete with MS installation Box with 2 Nos control Cocks, all accessories, connections etc all inclusive.
Supply, installation and commissioning all complete SENSOR FAUCET FOR URINALS (Model SNR-51077 Chrome, Make - Jaquar) concealed type
Flushing Valve complete set with Installation Box & Control Cock , all accessories, connections etc. all inclusive.
Providing and fixing 1200 x 450 x 18 mm (minimum) size machine cut and polished black / approved colour granite partition plate between urinals including
cutting masonry / concrete surface to required size, fixing the division plate on the ceramic tiles by means of SS clamps, nuts & bolts, polishing all exposed
surface etc all complete as directed by Engg.-In-Charge.
HAND WASH BASIN: Providing and fixing coloured (pastel colours) wash basins of size 550 x 400 without pedestal, including the following accessories:
(a)15mm brass CP Jaquar make (Cat.no.093) stop cock -1 No. (b) 15mm CP connections from the above stop cock to pillar cock - 1 No. (c) 32mm dia waste
coupling, CP brass chain and rubber stopper. (d) 30mm bottle trap Jaquar make with cleaning eye, extension piece and wall flange.
(d) Providing and fixing brass CP Jaquar make 13mm half turn pillar cock. (Cat. no.011). Rate to include supply, painting and fixing of necessary CI brackets
with nuts and bolts and fixing the wash basin with all necessary connections in walls.
Hand Wash basin with matching color pedestal. Rest specifications as item no. 172
Supplying and fixing ceramic WHITE COLOUR OVAL BELOW COUNTER BASIN of Parryware size 550x450 mm make No. 550 0418, CP flush valve, CP
pipe connection, CP waste coupling, CP Brass bottle trap, 32 mm PVC waste line of required length etc. all complete as per the direction of Engg.-In-
Charge. Approved Equivalent - Hindware 10016 Oval.
Supplying and fixing ceramic PASTEL COLOUR OVAL BELOW COUNTER BASIN of Parryware size 550x450 mm make No. 550 0418, CP flush valve, CP
pipe connection, CP waste coupling , CP Brass bottle trap, 32 mm PVC waste line of required length etc. all complete as per the direction of Engg.-In-Charge. Approved Equivalent - Hindware 10016 Oval.
Supplying and fixing ceramic approved colour Parryware make 580x455 mm size No. CTH-0481 wall hung wash basin with matching coulour ceramic
pedestal no. 0375, CP flush valve, CP pipe connection, CP waste coupling, CP Brass bottle trap, 32 mm PVC waste line ofrequired length etc. all complete
as per the direction of Engg.-In-Charge. The fixing shall be done by Parryware bolts only and the pedestal shall be screwed to floor as per manufacturer's
specifications. Approved Equivalent - Hindware wash basin Viking 10008, Pedestal 11003.
Providing and fixing beveled edge mirror ofsuperiorglass of5.5 mm thick 600 x 600 mm size ofBELGIUM GLASS or any other equivalent make, craft paper,
3mm thick felt backing or 6 mm asbestos sheet. Teak Wood beads 25x40 mm as per approved shape / drawing allround and fixed with wooden plugs with
CP brass screws and cup washers etc all complete as d irected by Engg.-In-Charge.
Same as item no. 177 but of size 600 x 600 mm.
Providing and fixing readymade CP brass soap tray near wash basin with CP brass screws of approved make.
Providing and fixing soap dispenser having refillable container system and transparent view of container showing remaining soap level. Care shall be taken so
that tiling is not damaged while installation. Make - Technocrats/ Euronics /Askon
Supplying and fixing of 150 x 150 mm pastel coloured toilet paper holder of Hindustan sanitary ware or equivalent approved make at required position and
elevation as directed. Rate to include making good the chases in walls after fixing the above.
Supplying and fixing PASTEL COLOURED vitreous china urinal of Parryware make Series No. C8098, CP flush valve, CP pipe connection, CP waste
coupling, CP Brass bottle trap, 32 mm PVC waste line of required length etc. all complete with in built sensor for water discharge and flushing. Rate include
making all connections / electrical connections etc complete job.
Bidder's Seal & Signature Page 16 of 37
-
7/31/2019 Rajasthan SOR
17/37
SL. NO DESCRIPTION UNIT RATE
SCHEDULE OF RATES - FOR RAJASTHAN STATE
182 TOWEL RAIL Each 250
183 TOWEL RING:CAN-1121, JAQUAR Each 650
184 TOWEL RING:1576, PARKO Each 575
185 AUTOMATIC HAND DRYER Each 6500
186 AUTOMATIC AEROSOL DISPENSER Each 2750
187 AUTOMATIC SHOE SHINING MACHINE Each 12100
188 HYGI SPRAY Each 540
189 STOP COCK CONCEALED-PARKO 1516 Each 510
190 SWAN NECK TAP-PARKO 1536 Each 775
191 PILLAR COCK-PARKO 1501 Each 400
192 BIB COCK LONG BODY-PARKO 1511 Each 510
193 BIB COCK LONG NOSE-PARKO 1506A Each 590
194 BIB COCK -PARKO 1506 Each 400
195 PILLAR COCK-JAQUAR 23011 Each 515
196 PILLAR COCK-JAQUAR 23021 Each 665
197 BIB COCK-JAQUAR 23037 Each 500
198 BIB COCK-JAQUAR 23039 Each 535
199 BIBCOCK LONG BODY-JAQUAR 23107 Each 685
Providing and fixing CP brass towel rail of 20 mm dia and 600 mm long including all accessories such as brackets (coloured), fixing and anchoring etc.
complete as directed.
Providing and fixing CP brass Towel Ring. Make-Jaquar, Continental Range CAN-1121 including all accessories such as brackets, fixing and anchoring etc.
complete as directed.
Providing and fixing CP brass Towel Ring. Make-Parko, Classic Line Collection, No.1576 including all accessories such as brackets, fixing and anchoring etc.
complete as directed.
Providing, fixing and commissioning fully automatic hand dryer i.e. autostart on positioning the hand and autostop. Care shall be taken so that tiling is not
damaged while installation. Rate includes PVC insulated power chord having copper conductor and Anchor ROMA make 3 pin power plug matching ampere
load of instrument. Make - Technocrats (Model Alpha AP-800) or Euronics (Model CYC 30).
Providing, fixing and commissioning fully automatic aerosol dispenser (Auto Freshener). The price includes spray fragrance cam with approved aroma etc.
complete. Rate includes PVC insulated power chord having copper conductor and Anchor ROMA make 3 pin power plug matching ampere load of
instrument. Care shall be taken so that tiling is not damaged while installation. Make - Technocrats (Model Deluxe).
Providing, fixing and commissioning fully automatic shoe polish machine with electronic eye (infra red sensor) having both separate black and brown rollers.
The machine shall start automatically when shoe is placed and automatically stop. Rate includes PVC insulated power chord having copper conductor and
Anchor ROMA make 3 pin power plug matching ampere load of instrument. Care shall be taken so that finishing is not damaged while installation. Make -
Technocrats (Model Executive Deluxe).
Providing and fixing in position CP brass Hygi Spray of Parryware make Model T9929G1 inclusive of all fixtures, fittings and fasteners making operationalcomplete. Approved Equivalent Make - Hindware.
Providing and fixing in position CP brass stop cock Parko make classic line series No. 1516 including all necessary fixtures etc. complete.
Providing and fixing in posit ion CP brass swan neck tap Parko make classic line series No. 1536 on wash basins including all necessary fixtures etc.
complete.
Providing and fixing in position CP pillar cock of Parko make classic line series No. 1501 including all necessary fixtures etc. complete.
Providing and fixing in position CP long body bib cock of Parko make classic line series No. 1511 including all necessary fixtures etc. complete.
Providing and fixing in position CP lon