rfic design example - scu bipolar, si cmos, gaas hbt, gaas mesfet/hemt, ... • s parameter: ......
TRANSCRIPT
Copy right 2003, ELEN351 1
RFIC Design ELEN 351 Lecture 1: General Discussion
Instructor: Dr. Allen Sweet
Copy right 2003, ELEN351 2
General Information
• Instructor: Dr. Allen Sweet• Email: [email protected]• Home work/project submissions: Place all
schematics, graphics, and layouts in a power point or ms word file and email to instructor. Hard copy is also acceptable.
• Grade: Based on homework, midterm, and project.
• Reference books: See handout list for suggestions.
Copy right 2003, ELEN351 3
Recommended General Software
• Ms Word• Ms Power Point• Snagit utility (demo at www.snagit.com)• APPCAD (Available from Agilent)
Copy right 2003, ELEN351 4
Simulator Options
• ADS by Agilent• Ansoft Serenade (RF package is called
Harmonica). Student version is available at www.ansoft.com/about/academics/sersv/index.cfm Note: the student version is limited to only 25 nodes and 2 transistors.
• Genesys by Eagleware• Golden Gate by Xpedian
Copy right 2003, ELEN351 5
Layout tool Options
• ICEditor (demo is available at www.iceditors.com, however files cannot be saved)
• Mentor Graphics• Cadence• AutoCAD • Fast CAD (demo is available at
www.fastcad.com, )
Copy right 2003, ELEN351 6
Course Outline• General RF/wireless concepts, simulators, simple
design example.• Receiver/Transmitter architectural options• Layout techniques• PA Design• LNA Design• Mixer Design• VCO Design• Battery issues and tradeoffs, economics of RFICs• Technology comparison
Copy right 2003, ELEN351 7
What is an RFIC?
• Any integrated circuit for used in the frequency range: 100 MHz to 6 GHz.
• Generally RFIC’s contain the analog front end of a radio transceiver, or some part of it.
• RFIC’s can be the simplest SP1T switch, up to the whole front end of a radio transceiver.
• RFIC’s are fabricated in a number of technologies: Si Bipolar, Si CMOS, GaAs HBT, GaAs MESFET/HEMT, and SiGe HBT are today’s leading technologies.
Copy right 2003, ELEN351 8
Typical Applications for RFICs
• Cellular / PCS phones• Cellular / PCS infrastructure• WLANS• GPS• BlueTooth• Wireless PDAs• Mobile Communications
Copy right 2003, ELEN351 9
Basic Radio Link
Copy right 2003, ELEN351 10
Path Loss Defines the Received RF Signal Level
Signal to Noise ratio
(In dB’s)
Copy right 2003, ELEN351 11
Shannon’s law gives Maximum Data Rate in an RF Channel
• Rmax = BW LOG2( 1 + S/N), where BW is the RF channel’s bandwidth in MHz and Rmax if the Maximum possible data rate for this channel in MBits per second.
• All practical MOD- DEMOD systems can only approach Shannon’s limit.
• Radio Spectrum is a precious commodity! It must be used wisely, to handle the growing amount of wireless information flow.
Copy right 2003, ELEN351 12
Multiple Access Techniques Conserve Valuable Spectrum
• Frequency Division Multiple Access (FDMA)
• Time Division Multiple Access (TDMA)• Code Division Multiple Access (CDMA)
Copy right 2003, ELEN351 13
FDMA
Copy right 2003, ELEN351 14
TDMA
Data Packets
Copy right 2003, ELEN351 15
CDMA
Copy right 2003, ELEN351 16
Block Diagram of a CDMA System
Note: Spreading and De Spreading codes are identical
Copy right 2003, ELEN351 17
Two Port S Parameters
Copy right 2003, ELEN351 18
Types of Device Models
• S Parameter: Limited to small signal gain and match analysis only.
• Equivalent Circuit: Same limitations as the S Parameter Model, except it is scalable with area.
• Load Pull Impedance: For PA design, limited in usefulness to output circuit design only.
• Large Signal Model: No limitations, this is the most useful class of models.With these models, ALL measurable parameters can be simulated.
Copy right 2003, ELEN351 19
Types of Large Signal Models
• GaAs HBT: Gummel-Poon, and VBIC• GaAs MESFET: Curtice, TOM, Materka,
Statz, Tajima, • GaAs HEMT: EE_HEMT• Si Bipolar: Gummel-Poon• CMOS: Many
Copy right 2003, ELEN351 20
The Impedance Smith Chart
OPEN(RESISTIVE AXIS)
INDUCTIVE
CAPACITIVE
LINES OF CONSTANTREACTANCE
CIRCLES OF CONSTANTRESISTANCE
Z0 POINT
SHORT
Copy right 2003, ELEN351 21
Impedance locus of a 10 ohm Resistor in series with a 5 nH coil
Copy right 2003, ELEN351 22
Impedance locus of a 10 ohm Resistor in series with a 5 pF cap
Copy right 2003, ELEN351 23
Impedance locus of an ideal 50 Ohm transmission line, Grounded
at one end
Copy right 2003, ELEN351 24
RFIC Design Process Steps
• Specifications• Identify Topology options (literature search)• Choose a Foundry• Obtain Foundry’s Device Models and Design
Rules• Initial Simulations• Choose final Topology• Stability Analysis (Amplifiers only)• Temperature Analysis
Copy right 2003, ELEN351 25
RFIC Design Process Steps, Continued
• Initial Layout• Include all Layout Parasitic elements in Topology• Minimize Layout Area, Preserving Performance
The Art of the Trade Off• Complete Final Layout• Create Test Cells for Critical Circuit Blocks• DRC at the Foundry• Assemble the Reticle, Tapeout• Mask Making, Wafer Fabrication
Copy right 2003, ELEN351 26
Homework Assignment #1: Simulate the following Amplifier
Copy right 2003, ELEN351 27
Circuit Details:FEEDBACKRESISTOR
INPUTBLOCKINGCAP
OUTPUTBLOCKING CAP
BIAS CHOKE
TRANSISTORAREA=3 FINGERS
BASE BIASSTABILIZING RESISTOR
Copy right 2003, ELEN351 28
Gummel Poon InGaP/GaAs HBT Device Model: 2x12 micron
emitter finger
Copy right 2003, ELEN351 29
Simulated Gain/Match/DC Conditions
GAIN
INPUT MATCH
OUTPUT MATCH
Copy right 2003, ELEN351 30
Smith Chart Display: Amplifier’s Input and Output Impedances
INPUT IMPEDANCE
OUTPUT IMPEDANCE
Copy right 2003, ELEN351 31
Simulated Noise Figure
Copy right 2003, ELEN351 32
Simulated Stability Factor (K)