sika plan -12g

7/27/2019 Sika Plan -12G

http://slidepdf.com/reader/full/sika-plan-12g 1/3

Product Data SheetEdition 11, 2006Version no. 08.04

SikaplanP®P 12 G 1/3

C o

n s t r u c t

i o n

Sikaplan® 12 G ProductDescription

Polyvinylchloride plastified (PVC-P) membrane, reinforced with woven fabric

Uses Waterproofing of flat and exposed roofs. Advantages Best resistance against weathering

High resistance against: ageing - hail - sparkling fire and radiant heat Resistant against common environment-influence High resistance against UV, VI, IR-rays High resistance against mechanically influences High tensile strength and elongation High stable in change of dimensions Excellent flexibility in cold

High water vapour permeability Best weldability Not resistant against bitumen

Standards Fire behaviour as per DIN 4102/part1, class B2 and SIA 183/2. Resistant against sparking fire and radiant heat as per DIN 4102/part7 Planning and installation of underground structures as per SIA 271 and DIN. Quality management system as per DIN EN ISO 9001. Quality control by external independent laboratories. Official quality certificates and agreements.

WeightsThickness Length Width Packing unit

Roll M2

Product DataThickness

1.20 mm 20.00 m 2.00 m1.54 m

1.00 m0.77 m

20 rolls = 800 m220 rolls = 616 m2

20 rolls = 400 m220 rolls = 308 m2

61.20 kg47.10 kg

30.60 kg23.60 kg

1.53 kg

Colour Top layer: Light grey / bottom layer: dark grey

Storage Rolls shall be stored in horizontal position, protected against sunlight, in cool anddry place.

Test as per DIN 16726 Requirement as per DIN16938

values

General appearance Free from blisters, cracks andcapillaries

Passed

Straightness (g) andflatness (p)

g ≤ 50mm / p ≤ 10mm g < 15mm / p <2mm

Thickness (d) Deviations:-0.10mm/+0.20mm

average value of effectivethickness

lowest single value1.00mm

Deviations

-0 mm/+0.08 mmlowest single value 1.17mm

Tensile strengthlongitudinal and traversal

≥800 N/mm2

> 1100 N/mm2

Elongation longitudinaland traversal

≥ 10% > 15 %

Seam Strength Crack must occur next toseam

passed

Tear propagationstrength longitudinal andtraversal

≥ 180 N > 250 N

Technical DataCharacteristics accordingto DIN 16938Stone Floor Sheet

®

Behaviour underhydrostatic pressure

Testing pressure 2 bar over24h watertight

passed

7/27/2019 Sika Plan -12G



Test as per DIN 16726 Requirement as per DIN16938

values

Puncture resistance Weight of impacting mass500g failing height 300m tight

Tight at falling height500 mm

Dimensional change afterstorage at +80°C

≤ 1.00 % < 0.5%

Appearance after storagein heat

No blisters passed

Behaviour when folding incold

No cracks at -20°C No cracks at -35°C

Determination of water

vapour permeability (μ)

≤ 30 000 20 000

Root Resistance No root penetrations PassedMembranes after laboratory testingGeneral appearance afterthermal ageing

Free from blisters andcapillaries

Passed

Behaviour when folding incold after thermal ageing


Behaviour when folding incold after artificialweathering


Behaviour when folding incold after storage inaqueous solutions


Test as per SIA V 280 Requirements as perSIA V 280

Values

Thickness deviation from nominalthickness:- 5 % /+ 10%lowest single value +/-10%

deviation from nominalthickness:+ 2 %lowest single value – 1 %

Uniaxial tension test min. 10% longitudinal 15 %transversal 15 %

Low temperature folding no cracks at –20°C passedHeat distortion < 0.50%,

no blisters

longitudinal 0.30%transversal 0.30%passed

Water vapourpermeability (μ)

no requirement 18.000

Ozone resistance all 3 samples must showscale 0 Passed

Heat ageing weight decrease < 2%decrease of uniaxial tension< 30%,ozone resistance: class 0

- 0.60 % (decrease)

± 10 %class 0

Hail resistance approached damaging speed≥ 17m/s

rigid backing 18 m/sflexible backing > 30 m/s

Artificial weathering change of mass ΔM < 3%,5000h, class 0

change of mass ΔM – 0.70% class 0

Root resistance no root perforationingrown root must die off

passed

Fire class fire class 4,smoke class 1

fire class 4smoke class 2

Behaviour in warm water low temperature folding:

no cracks at –20°C,decrease of uniaxial tension< 30%,change of mass ≤ 4%

passed

passedpassed

Mechanical puncture resistance tight at a height of300mmfalling mass 500g

tight at falling height of450mm

Technical DataCharacteristics according toSIA V 280, edition 1996

Joint strength rupture must occur outside ofweld, slipping or peeling ofwelded parts not allowed

passed

7/27/2019 Sika Plan -12G



Appl icat ion Appl icat ionStructure of surface Structure of surface structuredstructuredFixing method Loosely laid and mechanically fasteningInstallation procedure According to the valid installation instruction of manufacturer.Important Notes Not resistant against tar, bitumen, oil- and solvent containing mediums

Not resistant in direct contact against thermal insulation materials, such asPolystyrene,-and Polyurethane-hardfoam, as well as other plastics than PVC

Recycling of old productsParticularities Auxiliary products: Trocal S or Sikaplan 18 D, unreinforced membranes for

detailing works, as well as prefabricated elements for corners and pipepenetrations, and Sika-Trocal PVC-coated metal sheet, type S

Membranes in other colours of top layers on inquiry:slate grey approx. RAL 7015green approx. RAL 6061brick red approx. RAL 8004white approx. RAL 9010

Legal notes The information, and in particular, the recommendations relating to the application and end-use of

Sika products, are given in good faith based on Sika's current knowledge and experience of the

products when properly stored, handled and applied under normal conditions in accordance with

Sika’s recommendations. In practice, the differences in materials, substrates and actual site conditions

are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any

liability arising out of any legal relationship whatsoever, can be inferred either from this information, or

from any written recommendations, or from any other advice offered. The user of the product must test

the product’s suitability for the intended application and purpose. Sika reserves the right to change the

properties of its products. The proprietary rights of third parties must be observed. All orders are

accepted subject to our current terms of sale and delivery. Users must always refer to the most recent

issue of the local Product Data Sheet for the product concerned, copies of which will be supplied onrequest.

C o

n s t r u c t

i o n

Sika Egypt for Construction ChemicalsEl Abour City1

st industrial zone (A)

Section # 10 Block 13035,Egypt

Tel: +202- 6100714/15/16/17/18Fax:+202- 6100759Mob: +2012- 3908822/55www.sika.com.eg

sika plan -12g

Documents