all copier error codes

[email protected], 2002

1 A.B. Dick2 Canon3 Gestetner4 Konica5 Konica/Royal6 Minolta7 Mita8 Panasonic9 Ricoh10 Royal11 Sanyo12 Savin13 Sharp14 Toshiba15 Xerox

A.B. Dick 122A.B. Dick K120

A.B.Code Description

E1 Jam between paper feed and fuserE3 Jam in fuserE5 Clam shell openE6 Paper feed section cover is openJ1 Toner cartridge near emptyJ3 Drum cartridge not seated properlyJ7 Waste toner full (replace drum cartridge)L6 Key counter outL8 Exposure area overheatU1 No clock pulse (drive problem)U2 Scan problemU3 Lens/mirror problem (RE model only)U4 Heat problemU8 Exposure lamp control circuit problemE1 Jam between paper feed and fuserE3 Jam in fuserE5 Clam shell openE6 Paper feed section cover is openJ1 Toner cartridge near emptyJ3 Drum cartridge not seated properlyJ7 Waste toner full (replace drum cartridge)L6 Key counter outL8 Exposure area overheatU1 No clock pulse (drive problem)U2 Scan problemU3 Lens/mirror problem (RE model only)U4 Heat problemU8 Exposure lamp control circuit problem

Canon 10Canon 115Canon 1215Canon 14Canon 150Canon 1500Canon 155Canon 20Canon 2015Canon 2020Canon 210Canon 2120Canon 24Canon 25Canon 250Canon 270Canon 2LCanon 300Canon 3025Canon 3030Canon 3050Canon 3225Canon 3325Canon 350Canon 3525Canon 3725Canon 3825Canon 3llCanon 400Canon 4035Canon 4050Canon 4080Canon 4540Canon 4835Canon 500Canon 5LCanon 5llCanon 5LllCanon 6012FCanon 6030Canon 6035Canon 6045Canon 6085

Canon 6150Canon 6212Canon 6230Canon 6650Canon 7050Canon 720Canon 740Canon 7550Canon 770Canon 790Canon 8070Canon 8530Canon 8570Canon 8580Canon 9800Canon A-1, B1Canon C-120Canon C-160Canon C-180Canon C200DCanon NP 1820Canon NP 6012Canon NP 6016Canon NP 6025Canon NP 6060Canon NP112Canon NP6521Canon PC 710Canon PC 850Canon PC-1Canon PC-2Canon PC3Canon PC5Canon PC-5Canon PC5LCanon PC6Canon PC7

Canon 10Code Description

E2 ScannerEO Heat lamp

Canon 1215Code DescriptionE000 Low temperature, thermoswitch, thermistor or AC driverE001 High temperature, thermistor, AC driverE030 CounterE202 Scan not returning home. Scan not leaving homeE221 Lamp regulator boardE400 Document feeder problemE500 Sorter problem


E0 Thermistor, thermal switch, heatE1 Sorter, scanner homeE2 Motor, clock pulseE3 Scan problem (150 only)E4 Lens homeE5 Lamp regulator/document sensorE6 Motor controlE7 Total counterE8 Lamp regulatorE9 Copyboard drive motor/boardED Motor control PCBEE DC controller on motor

E001 High fuser temperature. Shorter fuser thermistorE030 Total counter disconnected or openE202 Scan problemE210 Lens problemE221 DC power supply, lamp regulator board or main boardE400 Document feeder board problemE500 Sorter board problem

EOOO Low fuser temperature

Canon 1500Code DescriptionE001 High fuser temperature. Shorter fuser thermistorE030 Total counter disconnected or openE202 Scan problemE210 Lens problemE221 DC power supply, lamp regulator board or main boardE400 Document feeder board problemE500 Sorter board problem

EOOO Low fuser temperature


E0 Thermistor, thermal switch, heatE1 Sorter, scanner homeE2 Motor, clock pulseE3 Scan problem (150 only)E4 Lens homeE5 Lamp regulator/document density sensorE6 Motor control boardE7 Total counterE8 Lamp regulatorE9 Copyboard drive motor/boardED Motor control PCBEE DC controller on motor



D030 Total counter or DC controllerE00 Heater (Press SW301 twice to reset)E001 Over temperatureE010 Drum drive clock pulseE202 Scan home positionE204 Registration switch (scan problem)E210 Lens homeE221 Lamp regulator or DC controllerE400 Document feed problem (Check circuit breaker)E500 Sorter (Check circuit breaker)E000 Fuser problem. Low temperature. Lamp, thermal switch, AC driverE001 Fuser problem. High temperature. Triac, AC driver, pinched wireE004 Fuser problemE0053 SorterE030 CounterE030 CounterE202 ScanE202 ScanE210 LensE210 LensE221 Exposure lamp regulator board, thermal fuse, exposure lampE221 Lamp regulator boardE400 Automatic document feederE400 ADFE500 SorterE500 SorterE710 DC controller (main board)E710 DC controllerEOO1 Heater problemEOOO Heater problem

Canon 2015Code DescriptionD030 Total counter or DC controllerE00 Heater (Press SW301 twice to reset)E001 Over temperatureE010 Drum drive clock pulseE202 Scan home positionE204 Registration switch (scan problem)E210 Lens homeE221 Lamp regulator or DC controllerE400 Document feed problem (Check circuit breaker)E500 Sorter (Check circuit breaker)

Canon 2020Code DescriptionE000 Fuser problem. Low temperature. Lamp, thermal switch, AC driverE001 Fuser problem. High temperature. Triac, AC driver, pinched wireE004 Fuser problemE0053 SorterE030 CounterE030 CounterE202 ScanE202 ScanE210 LensE210 LensE221 Lamp regulator boardE221 Exposure lamp regulator board, thermal fuse, exposure lampE400 ADFE400 Automatic document feederE500 SorterE500 SorterE710 DC controller (main board)E710 DC controllerEOO1 Heater problemEOOO Heater problem


E0 Heat problemE1 SorterE2 ScannerE4 Drum driveE5 Lens driveE6 Exposure lampE7 Mirror sensors

Canon 2120Code DescriptionE000 Fuser problem. Low temperature. Lamp, thermal switch, AC driverE001 Fuser problem. High temperature. Triac, AC driver, pinched wireE004 Fuser problemE0053 SorterE030 CounterE202 ScanE210 LensE221 Exposure lamp regulator board, thermal fuse, exposure lampE400 Automatic document feederE500 SorterE710 DC controller


E2 ScannerEO Heat lampE0 Thermistor/thermoswitch or heat lampsE1 SorterE2 Scanner homeE3 Scanner returnE4 Right front door/main motorE5 Lens homeE6 Lamp regulatorE8 Counter wire


E0 Thermistor/thermoswitch or heat lampsE1 SorterE2 Scanner homeE3 Scanner returnE4 Right front door/main motorE5 Lens homeE6 Lamp regulatorE8 Counter wire

Canon 2LCode Description

E1 The heater film has gone off center. Turn machine off & on, make sure it's level etc.E2 Scan problmeE6 Exposure lamp or exposure lamp sensorEO Heater problem


E0 Heat problemE1 SorterE2 ScannerE4 Drum driveE5 Lens driveE6 Exposure lampE7 Mirror sensors

Canon 3025Code DescriptionE000 Fuser problemE000 HeatE000 Fuser problemE010 Main motor, motor board, clock pulseE010 DriveE030 CounterE030 CounterE050 Duplex side to side problemE050 Duplex problem with cross alignmentE051 Duplex side to side problemE051 Crossway registrationE200 Scan problemE200 Scan reverse sensor or scanE202 Scan return problemE202 Scan home sensor or home scanE204 ScanE204 Document sensor, scan reverse sensor or scaleE210 Lens problemE210 LensE220 LensE220 Blank lamp open or lens home problemE240 DC controllerE240 Bad DC controllerE400 Document feed problemE400 Document feeder board problem or document feeder interface problemE500 SorterE620 EditorE620 Editing problem

Canon 3030Code DescriptionE000 Fuser temp low. Heat lamp, thermoswitch, thermistor, SSRE001 Fuser temperature too high or shorted thermistorE002 Fuser temperature too lowE003 Fuser temperature too lowE004 SSR, or lamp reg. boardE010 Drive problemE022 DV unit switching problemE030 Counter not working/openE202 Scan problem. Scan sensor, scan motorE204 Scan problem. Scan sensor, scan motorE210 Lens problem. Lens sensor, lens motorE220 Exposure lampE240 DC controller (main board)E400 RDF circuit boardE401 RDF pickup motor driveE402 RDF belt motor driveE403 RDF feed drive problemE404 RDF exit motorE411 RDF sensor problemE500 Sorter board problemE510 Sorter feed motorE512 Sorter delivery motorE514 Sorter delivery motorE520 Sort stack motorE530 Vibrator motorE531 Stapler motorE535 Vibrator motorE540 Shift problemE541 Shift problemE710 DC controllerE711 DC controllerE712 DC controller. Document feeder board or cable

E800 Auto shut off relay

Canon 3050Code DescriptionE000 Fuser temp low. Heat lamp, thermoswitch, thermistor, SSRE001 Fuser temperature too high or shorted thermistorE002 Fuser temperature too lowE003 Fuser temperature too lowE004 SSR, or lamp reg. boardE010 Drive problemE022 DV unit switching problemE030 Counter not working/openE202 Scan problem. Scan sensor, scan motorE204 Scan problem. Scan sensor, scan motorE210 Lens problem. Lens sensor, lens motorE220 Exposure lampE240 DC controller (main board)E400 RDF circuit boardE401 RDF pickup motor driveE402 RDF belt motor driveE403 RDF feed drive problemE404 RDF exit motorE411 RDF sensor problemE500 Sorter board problemE510 Sorter feed motorE512 Sorter delivery motorE514 Sorter delivery motorE520 Sort stack motorE530 Vibrator motorE531 Stapler motorE535 Vibrator motorE540 Shift problemE541 Shift problemE710 DC controllerE711 DC controllerE712 DC controller. Document feeder board or cable

E800 Auto shut off relay

Canon 3225Code DescriptionE000 Fuser problemE010 DriveE030 CounterE050 Duplex side to side problemE051 Duplex side to side problemE200 Scan problemE202 Scan return problemE204 ScanE210 Lens problemE220 Blank lamp open or lens home problemE240 Bad DC controllerE400 Document feeder board problem or document feeder interface problemE500 SorterE620 Editing problem

Canon 3325Code DescriptionE000 Low fuser temperature. Heat lamp, thermoswitch, thermofuse, thermistor, SSRE001 High fuser temperature. Thermistor, SSR, pinched wireE002 Low fuser temperature. Same as E002E003 Same as E000/E001E010 Same as E002E022 Motor drive problemE030 CounterE202 Scan motor, sensorE204 Scan motor, sensorE210 Lens motor, sensorE220 Exposure lampE240 DC controller (main board)E401 Pickup drive problem (might be Doc. Feeder)E402 Document belt drive problemE404 Exit motor (document feeder)E411 Document sensor (document feeder)E500 Sorter/machine communication problemE510 Sorter drive problemE530 Sorter home sensorE531 Stapler unit swing sensorE540 Sorter cam sensorE541 Sorter cam sensorE710 DC controller (main board)E712 DC controller or document feeder board

Canon 3525Code DescriptionE000 Fuser problemE000 HeatE010 Main motor, motor board, clock pulseE010 DriveE030 CounterE030 CounterE050 Duplex side to side problemE050 Duplex problem with cross alignmentE051 Duplex side to side problemE051 Crossway registrationE200 Scan problemE200 Scan reverse sensor or scanE202 Scan return problemE202 Scan home sensor or home scanE204 ScanE204 Document sensor, scan reverse sensor or scaleE210 Lens problemE210 LensE220 LensE220 Blank lamp open or lens home problemE240 DC controllerE240 Bad DC controllerE400 Document feeder board problem or document feeder interface problemE400 Document feed problemE500 SorterE620 EditorE620 Editing problem

Canon 3725Code DescriptionE000 Fuser problemE010 DriveE030 CounterE050 Duplex side to side problemE051 Duplex side to side problemE200 Scan problemE202 Scan return problemE204 ScanE210 Lens problemE220 Blank lamp open or lens home problemE240 Bad DC controllerE400 Document feeder board problem or document feeder interface problemE500 SorterE620 Editing problem

Canon 3825Code DescriptionE000 Low fuser temperature. Heat lamp, thermoswitch, thermofuse, thermistor, SSRE001 High fuser temperature. Thermistor, SSR, pinched wireE002 Low fuser temperature. Same as E002E003 Same as E000/E001E010 Same as E002E022 Motor drive problemE030 CounterE202 Scan motor, sensorE204 Scan motor, sensorE210 Lens motor, sensorE220 Exposure lampE240 DC controller (main board)E401 Pickup drive problem (might be Doc. Feeder)E402 Document belt drive problemE404 Exit motor (document feeder)E411 Document sensor (document feeder)E500 Sorter/machine communication problemE510 Sorter drive problemE530 Sorter home sensorE531 Stapler unit swing sensorE540 Sorter cam sensorE541 Sorter cam sensorE710 DC controller (main board)E712 DC controller or document feeder board

Canon 3llCode Description



E0 FuserE1 SorterE2 Scan homeE3 ScanE4 Clock pulse or open RF doorE5 Lens positionE6 Exposure lamp, fuse 2E8 Counter

Canon 4035Code DescriptionE000 Low fuser temperatureE001 High fuser temperatureE010 Main motor clock pulseE011 Bind or load on main motorE020 No TF for 3 minutesE030 Copy counterE050 Duplex unitE201 Scan motorE203 Scan motorE210 Lens homeE240 DC controllerE241 DC controllerE320 CCDE400 DC controller, 24VE500 DC controller, 24VE510 Finisher feed motorE520 Stacker motorE530 Guide plate shift motorE531 Stapler motorE620 DC controller, edit board

Canon 4050Code DescriptionE000 No fuser heatE001 High fuser temperature or shorter thermistorE002 Low temperature or bad thermistorE003 Fuser problemE004 Bad SSR (heat staying on)E010 DriveE020 Black toner motorE030 CounterE080 Interface problem with color unitE081 Vertical drive motorE082 Horizontal drive motorE083 Color unit sensor on rightE084 Color unit sensor on leftE085 Color unit release sensor or release or solonoidE086 Color unit claw releaseE089 Laser problemE100 Laser problemE110 Laser motorE140 LaserE202 ScanE203 ScanE204 ScanE210 LensE223 Color unit filter drive motorE240 DC controllerE401 RDF pickup motorE402 RDF belt motorE403 RDF feed motorE411 RDF document sensorE500 Sorter-Copier communication errorE510 Sorter driveE512 Sorter drive

E513 Sorter driveE514 Sorter driveE520 Top limit sensor or stack sensorE530 Sorter home sensorE531 Stapler home sensorE535 Stapler swing sensorE540 Stack shift sensorE660 IC cardE710 DC controllerE711 DC controllerE714 DC controllerE800 Power off circuit

Canon 4080Code DescriptionE000 No fuser heatE001 High fuser temperature or shorter thermistorE002 Low temperature or bad thermistorE003 Fuser problemE004 Bad SSR (heat staying on)E010 DriveE020 Black toner motorE030 CounterE080 Interface problem with color unitE081 Vertical drive motorE082 Horizontal drive motorE083 Color unit sensor on rightE084 Color unit sensor on leftE085 Color unit release sensor or release or solonoidE086 Color unit claw releaseE089 Laser problemE100 Laser problemE110 Laser motorE140 LaserE202 ScanE203 ScanE204 ScanE210 LensE223 Color unit filter drive motorE240 DC controllerE401 RDF pickup motorE402 RDF belt motorE403 RDF feed motorE411 RDF document sensorE500 Sorter-Copier communication errorE510 Sorter driveE512 Sorter drive

E513 Sorter driveE514 Sorter driveE520 Top limit sensor or stack sensorE530 Sorter home sensorE531 Stapler home sensorE535 Stapler swing sensorE540 Stack shift sensorE660 IC cardE710 DC controllerE711 DC controllerE714 DC controllerE800 Power off circuit

Canon 4540Code DescriptionE00 Low fuser temperatureE001 High fuser temperatureE010 Main motor clock pulseE011 Bind or load on main motorE020 No TF for 3 minutesE030 Copy counterE050 Duplex unitE201 Scan motorE203 Scan motorE210 Lens homeE240 DC controllerE241 DC controllerE320 CCDE400 DC controller, 24VE500 DC controller, 24VE510 Finisher feed motorE520 Stacker motorE530 Guide plate shift motorE531 Stapler motorE620 DC controller, edit board

Canon 4835Code DescriptionE000 Low fuser temperatureE001 High fuser temperatureE002 Low fuser temperatureE003 Low fuser temperatureE010 DriveE030 CounterE080 Color change board problemsE081 Color horizontal motor problemE082 Color horizontal motor problemE083 Color problem in vertical directionE084 Color problem in vertical directionE085 Color problem in vertical directionE086 Color unit claw release problemE089 Color change incompleteE100 Laser problemE110 Laser motor problemE140 Laser unitE203 Scan drive problemE210 Lens not home or won't leave homeE240 DC controllerE401 Document feeder pick up motorE402 Document feeder belt motorE403 RADF feed motorE404 Document feeder motorE411 Document feeder sensorE500 Sorter to DC control interface problemE510 Stapler/sorter motorE530 Stapler swing motorE531 Stapler swing motorE540 Sorter bin motorE541 Sorter bin motorE710 DC controller

E711 DC controllerE712 DC controller to document feeder interface problem


E0 FuserE1 SorterE2 Scan homeE3 ScanE4 Clock pulse or open RF doorE5 Lens positionE6 Exposure lamp, fuse 2E8 Counter

Canon 5LCode Description

E1 The heater film has gone off center. Turn machine off & on, make sure it's level etc.E2 Scan problmeE6 Exposure lamp or exposure lamp sensorEO Heater problemE1 The heater film has gone off center. Turn machine off & on, make sure it's level etc.E2 Scan problmeE6 Exposure lamp or exposure lamp sensorEO Heater problemE1 The heater film has gone off center. Turn machine off & on, make sure it's level etc.E2 Scan problmeE6 Exposure lamp or exposure lamp sensorEO Heater problem

Canon 5llCode Description

E1 The heater film has gone off center. Turn machine off & on, make sure it's level etc.E2 Scan problmeE6 Exposure lamp or exposure lamp sensorEO Heater problemE1 The heater film has gone off center. Turn machine off & on, make sure it's level etc.E2 Scan problmeE6 Exposure lamp or exposure lamp sensorEO Heater problem

Canon 5LllCode Description


Canon 6012FCode Description

C No problem. Means that the machine is correcting the fuser film tracking.

CC Drum must be changed. Could be the drum serial number is identified by the logic as beingnon-compatible to that particular copier.E000 Low fuser temperatureE001 High fuser temperatureE002 High fuser temperatureE003 Erratic fuser temperatureE007 Fuser film off track and will not repair itselfE010 Main drive problemE030 Counter problemE064 Scan problem, or power supplyE202 Scan problemE210 Lens drive problem or lens sensorE220 Exposure lamp stays on or offE240 DC controller (main board) or composite power supplyE261 Zero cross problem. Power frequency or composite power supplyE400 Communication problem between boardsE803 24 volt problemEO Fuser problemH Fuser overheat

Canon 6030Code DescriptionE000 Fuser did not heat upE001 Fuser temperature too highE002 Fuser temperature not rising at correct paceE003 Fuser temperature dropsE004 SSR shortedE210 Lens home problemE212 Lens home problemE220 Exposure lamp problemE224 Blank shutter home problemE240 DC controller or composite power supply problemE400 Data communication problemE401 Pickup motor problemE402 Belt motor problemE403 Feeder motorE404 Delivery motorE411 Document detect sensorE500 Communication problem with copierE510 Feeder motorE530 Home sensorE531 Staple swing sensor problemE540 Bin shift motor rotation problemE541 Bin motorE710 DC controllerE711 Document feeder IC failureE716 Cassette feed IC failureE800 Auto power-off circuit problemE901 Cassette feed motorE902 Paper guide home sensor problem


E000 Fuser did not heat up. Lamp, thermal switch, thermistors, connections, AC driver, DC controller, SSR,etc.E001 Fuser temperature too high. Same possibilities as E000, as well as shorted wire.E002 Fuser temperature not rising at correct pace. Same possibilities as E000E003 Fuser temperature drops. Same as E003.E004 Fuser problem. AC driver, SSR bad, wire shorted.E010 Drive problem. Main motor, gears, etc.E030 Total counter.E064 Composite power board or DC controller.E065 Composite power board or DC controller.E202 Scan motor or scan sensor problem. Panel locked with no code. Scan motor problem.E203 Scan problem or scan sensor.E204 Scan problem or scan sensor.E210 Lens sensor or motor problem.E212 Lens sensor or motor problem.E220 Exposure lamp or exposure lamp regulator board.E224 Blanking shutter motor or sensor.E240 DC controller or composite power supply problem.E244 DC controller.E400 RDF to copier communication problem.E401 RDF Pickup motor or pick up sensor.E403 RDF feed motor or pulse sensor.E404 RDF delivery motion problem.E404 RDF delivery motor problem.E411 RDF tray sensor or registration sensor.E500 Sorter main board or communication with copier.E510 Sorter feed motor.E530 Sorter guide bar motor.E531 Sorter stapler motor.E540 Sorter bin shift motor.E541 Sorter bin motor.E550 Sorter power supply.E710 DC controller

E711 DC controllerE712 Document feeder IC failure.E716 DC controller. Sorter.E800 Auto power off function (DC controller)E901 Pedistal motor.E902 Jogger side plate sensor or motor.


E000 Fuser did not heat up. Lamp, thermal switch, thermistors, connections, AC driver, DC controller, SSR,etc.E001 Fuser temperature too high. Same possibilities as E000, as well as shorted wire.E002 Fuser temperature not rising at correct pace, same possibilities as E000.E003 Fuser temperature drops. Same as E000.E004 Fuser problem: AC driver, SSR bad, wire shorted.

E005 Fuser cleaning web, or problem with sensor, lever or connector. Service mode 6 is the probably resetfor this.E006 Fuser feed connector.E010 Drive problem. Main motor, gears, etc.E013 Waste toner drive problem, or waste toner sensor switch has been actuated too many times.E015 Pickup motor power supply. Could be bad motor or motor board, or DC controller.E020 Problem with developer unit, toner hopper, hopper motor, connection, sensor or DC controller.E030 Total counter.E031 Option counter or total counter.E050 Holding tray (duplex) home position sensor motor or board.E051 Holding tray (duplex) home sensor motor or board.E202 Panel locked up, but might be no code, scan motor problem.E203 Scan problem or scan sensorE204 Scan problem or scan sensorE210 Lens sensor or motor problemE212 Lens sensor or motor problemE213 Scan lock sensor or lock solenoidE220 Exposure lamp regulator boardE240 DC controller or composite power supply problem.E243 DC controllerE400 RDF to copier communication problemE401 RDF pickup motor or pickup sensor.E402 RDF belt motor or pulse sensor.E403 RDF feed motor or pulse sensor.E411 RDF tray sensor or registration sensorE500 Sorter main board or communication with copierE510 Sorter feed motor

E522 Sorter push bar motorE523 Sorter reference wall motorE524 Sorter multi-guide motorE525 Sorter bin paper sensor automatic adjustment problemE526 Sorter bin paper sensor automatic adjustment problemE530 Sorter guide bar motorE531 Sorter stapler motorE532 Stapler motorE533 Stapler inside paper sensorE540 Sorter bin shift motorE550 Sorter power supplyE710 DC controllerE711 DC controllerE712 Document feeder IC failureE713 DC controller, sorterE800 Auto power off circuit problem. Main switch or DC controller.E802 Auto power off circuit problem. Main switch or DC controller.

Canon 6085Code DescriptionE000 After power-on, the upper fixing roller does not reach 100 C within 5 min.E001 The temperature of the upper fixing roller exceeds 230 C for 5 sec or more.

E002 After the temperature of the upper fixing roller has exceeded 100 C, it does not reach 180 C within 5min.

E003 After the temperature of the upper fixing roller has reached 180 C, it drops to 100 C or less for 5 secor more.E005 The length used of the cleaning belt inside the fixing assembly has exceeded a specific value.E012 After the drum motor drive signal has been generated, clock pulses are not generated within 2 sec.

E013 After the waste toner feeding screw has become locked, the detecting switch (SW20) is pressed amultiple number of times within a specific period of time.E014 When the fixing motor (M17) is rotating, an error is detected for 2 sec or more.

E015 After the pick up motor drive signal has been generated, clock pulses have not been generated within2 sec.E019 As many as 50,000 have been made after detecting a waste toner full condition.

E020During copying, the toner supply signal is 0', indicating the absence of toner, for 3 min or more.During toner supply sequence at time of installation, the toner supply signal does not go '1' after 6min or more.

E030 After the total copy counter has turned OFF, an open circuit is detected for the total copy counter.

E032 After the clock pulse signal reached the IPC communication format of the copier DC controller PCB,the Copy Data Controller-A1 does not detect the signal.

E050While the paper jogging guide motor (M11) drive signal is being generated, the paper guide homeposition signal (THP) is not generated for 2 sec or more. While the paper jogging guide motor (M11)is being generated, the paper jogging guide home position signal (THP) is generated for two sec ormore.

E202 The scanner home position signal (SCHP) is not generated within 10 sec after the power switch orthe Copy Start Key is pressed.E203 While the scanner motor drive signal is being generated, clock pulses are not generated within 2 sec.

E204 The scanner leading edge signal (SCDP1) is not generated within 0.8 sec after the scanner hasstarted to move

E209 The scanner C.F.F. position signal (SCFFP) is not generated within 10 sec after the C.F.F. has beensent.

E210 The lens X home position signal (SCFFP) is not generated within 10 sec after the C.F.F. has beensent.

E212 The lens Y home position signal (LYHP) is not generated within 9 sec after the power switch or theCopy Start Key is turned ON. The lens Y home position signal (LYHP) is generated for 2 sec or more.

E213 In stream reading mode, the scanner original leading edge sensor 2 signal (SCDP2) is not generatedfor 5 pages continuously.

E214 While the scanner cooling fan (FM1, FM10, FM11) is rotating, an error signal is generated for 2 sec ormore.

E270 In stream reading mode, the scanner leading edge signal(SCDP2) is not generated within a specificperiod of time after a command has been issued to lock the scanner.E710 At power-on the IPC (Q170) on the DC controller PCB cannot be initialized.E711 After power-on the IPC (Q170) on the DC controller PCB goes out of order.E712 The communication IC on the RDF controller PCB has gone out of order.E713 The communication IC on the sorter control PCB has gone out of order.E715 The communication IC on the C.F.F. controller PCB has gone out of order.E717 The communication IC on the Copy Data Controller-A1 PCB has gone out of order.E800 An open circuit is detectedE801 Current flows from the activation circuit in the absence of the scanning lamp ON signal.E802 The relay (RL3) in the power supply unit does not operate in spite of the auto power-off signal.

Canon 6150Code DescriptionE000 ThermistorE001 SSRE002 Thermistor, ht. Lamp thermal fuse or SSRE003 Thermistor, ht. Lamp thermal fuse or SSRE005 Fuser cleaning beltE010 Main drive problemE020 Toner motor, toner level sensor, toner hopper sensorE030 CounterE050 Duplex problemE203 Scan home problemE210 Lens home sensorE401 Document feeder paper pickup motorE402 Document feeder belt clock pulse problemE403 Document feeder main motor clock pulse problemE411 Document feeder sensor problemE500 Sorter/copier interface problemE510 Sorter motor driveE530 Sorter home sensorE531 Stapler swing sensorE540 Sorter lead cam home sensorE541 Sorter lead cam home sensorE710 DC controller boardE711 DC controller boardE712 Document feeder problem


E000 Fuser did not heat up. Lamp, thermal switch, thermistors, connections, AC driver, DC controller, SSR,etc.E001 Fuser temperature too high. Same possibilities as E000, as well as shorted wire.E002 Fuser temperature not rising at correct pace. Same possibilities as E000E003 Fuser temperature drops. Same as E003.E004 Fuser problem. AC driver, SSR bad, wire shorted.E010 Drive problem. Main motor, gears, etc.E030 Total counter.E064 Composite power board or DC controller.E065 Composite power board or DC controller.E202 Scan motor or scan sensor problem. Panel locked with no code. Scan motor problem.E203 Scan problem or scan sensor.E204 Scan problem or scan sensor.E210 Lens sensor or motor problem.E212 Lens sensor or motor problem.E220 Exposure lamp or exposure lamp regulator board.E224 Blanking shutter motor or sensor.E240 DC controller or composite power supply problem.E244 DC controller.E400 RDF to copier communication problem.E401 RDF Pickup motor or pick up sensor.E403 RDF feed motor or pulse sensor.E404 RDF delivery motion problem.E404 RDF delivery motor problem.E411 RDF tray sensor or registration sensor.E500 Sorter main board or communication with copier.E510 Sorter feed motor.E530 Sorter guide bar motor.E531 Sorter stapler motor.E540 Sorter bin shift motor.E541 Sorter bin motor.E550 Sorter power supply.E710 DC controller

E711 DC controllerE712 Document feeder IC failure.E716 DC controller. Sorter.E800 Auto power off function (DC controller)E901 Pedistal motor.E902 Jogger side plate sensor or motor.

Canon 6650Code DescriptionE000 ThermistorE001 SSRE002 Thermistor, ht. Lamp thermal fuse or SSRE003 Thermistor, ht. Lamp thermal fuse or SSRE005 Fuser cleaning beltE010 Main drive problemE020 Toner motor, toner level sensor, toner hopper sensorE030 CounterE050 Duplex problemE203 Scan home problemE210 Lens home sensorE401 Document feeder paper pickup motorE402 Document feeder belt clock pulse problemE403 Document feeder main motor clock pulse problemE411 Document feeder sensor problemE500 Sorter/copier interface problemE500 An error is identified in the communication between the sorter and the copierE510 The clock signal from the motor is absent for 250ms or moreE510 Sorter motor driveE513 The clock signal from the motor is absent for 250 ms or moreE530 Sorter home sensor

E530 The home position sensor (P17) fails to go OFF when an equivalent of 2560 pulses of the motor drivecommand has been generated

E531 The stapler unit swing sensor (MS9) fails to go ON within 500 ms after the motor drive command hasbeen generated. MS9 fails to go back OFF within 1000 ms after it has gone onE531 Stapler swing sensor

E540 The lead cam home position sensor (P12) fails to go OFF within 2000 ms after the motor drivecommand has been generated. P12 fails to go back ON within 2000 ms after it has gone OFFE540 Sorter lead cam home sensorE541 Sorter lead cam home sensorE710 DC controller boardE711 DC controller boardE712 Document feeder problem

Canon 7050Code DescriptionE000 Heater (Reset by unplugging machine)E001 Heater triac, DC controller, AC driver (reset by unplugging)E005 Fuser cleaner belt at end. Replace.E010 Main motor, DC controller or DC driver board

E011 Any motor ( main, scan, cleaner belt, duplex, toner, lens) DC driver, DC controller, duplex driverboard.E020 Toner out signal has been sent for at least 3 minutesE050 DuplexE203 Scan motor, DC driver, DC controllerE210 Lens home sensor not actuated or won't deactuateE240 Controller boardE241 Controller boardE242 Controller boardE400 DC controller, Doc. Feeder board, 24V power supplyE500 DC controller, sorter board, 24V power supply

Canon 7550Code DescriptionE000 Heater (Reset by unplugging machine)E001 Heater triac, DC controller, AC driver (reset by unplugging)E005 Fuser cleaner belt at end. Replace.E010 Main motor, DC controller or DC driver board

E011 Any motor ( main, scan, cleaner belt, duplex, toner, lens) DC driver, DC controller, duplex driverboard.E020 Toner out signal has been sent for at least 3 minutesE050 DuplexE203 Scan motor, DC driver, DC controllerE210 Lens home sensor not actuated or won't deactuateE240 Controller boardE241 Controller boardE242 Controller boardE400 DC controller, Doc. Feeder board, 24V power supplyE500 DC controller, sorter board, 24V power supply

Canon 8070Code DescriptionE000 Fuser problem. Temperature too low. Heat lamp, thermal fuse or thermoswitch, thermistor, triac etcE001 Fuser problem. Temperature too high. Probably triacE005 Fuser web finishedE005 Fuser cleaner belt user upE010 DriveE010 Main drive problemE011 Drive problem. Could be main motor, scan motor, cleaning web motor or duplex motor

E011 Main motor, scan motor, cleaner belt motor, duplex motor, toner motor, lens motor or driver bd. forany of theseE020 Toner sensor problem or lack of toner feed. This occurs if toner feed signal is present for 3 minE020 Toner empty sensor sees no toner added for 3 min probably toner feed problemE050 Duplex problemE050 Duplex problemE203 Scan motor problemE203 Scan motorE210 Lens motor problemE210 Lens home sensor or lens won't leave homeE240 DC controller boardE240,E241,E242

Control board (main board)

E241 DC controller boardE242 DC controller boardE243 Operation panel boardE243 Operation panelE400 DC controller, ADF board or 24VE400 DC controller or document feed boardE500 DC controller or sorter boardE500 DC controller, sorter board or 24VE510 Finisher; feed motor, pulse sensor, finisher boardE510 FinisherE520 Finisher; stack motor, stack tray sensor, finisher boardE520 Finisher

E530 FinisherE530 Finisher; guide plate motor, stapler guide, finisher boardE531 FinisherE531 Finisher; staple motor, staple sensor, finisher board.EOO1 High fuser temperatureEOOO Low fuser temperature


E000

The surface temperature of the fixing assembly upper roller fails to rise by a specified value within 90sec after power-on. The surface temperature of the fixing assembly upper roller fails to reach 150 Cwithin 8 min after power -on. The surface temperature of the fixing assembly upper roller fails toreach 180 C within 5 min after it has reached 150 C. The surface temperature of the fixing assemblyupper roller falls below 50 C in standby.

E001 The surface temperature of the fixing assembly upper roller exceeds 250 C.E005 The cleaning belt inside the fixing assembly has been taken up more than a specified length.E010 After generation of the main motor drive signal, two or more pulses are not received within 2 sec.

E020 The accumulative time during which the toner supply signal (TSP) has been generated by thedeveloping assembly reaches 3 min.

E050The holding tray home position signal (THP) is not generated within 4 sec while the holding traymotor drive signal (TMDP1,2) is being generated. The holding tray home position signal (THP) isgenerated 1 sec or more while the holding tray motor drive signal (TMDP1.2) is being generated.

E13 The error detection circuit on the waste toner feed motor driver PCB has detected on overcurrent.

E203 Input of two or more clock pulses is not received within 2 sec from the scanner motor drive signal isgenerated.

E210 The lens home position signal (LHP) is not generated within 4.8 sec after the power switch or doorswitch has gone ON. The lens home position signal (LHP) is generate 2 sec or more.E240 An error has occurred in the microprocessor on the DC controller PCB.

E243 An error has occurred in the communication between the microprocessor of the DC controller PCBand the microprocessor in the control panel.

E710 An error has occurred in the communication between the DC controller PCB and the controller PCBof the option, and the DC controller has detected the error.

Canon 8570Code DescriptionE000 Fuser problem. Temperature too low. Heat lamp, thermal fuse or thermoswitch, thermistor, triac etcE001 Fuser problem. Temperature too high. Probably triacE005 Fuser web finishedE005 Fuser cleaner belt user upE010 DriveE010 Main drive problemE011 Drive problem. Could be main motor, scan motor, cleaning web motor or duplex motor

E011 Main motor, scan motor, cleaner belt motor, duplex motor, toner motor, lens motor or driver bd. forany of theseE020 Toner sensor problem or lack of toner feed. This occurs if toner feed signal is present for 3 minE020 Toner empty sensor sees no toner added for 3 min probably toner feed problemE050 Duplex problemE050 Duplex problemE203 Scan motor problemE203 Scan motorE210 Lens motor problemE210 Lens home sensor or lens won't leave homeE240 DC controller boardE240,E241,E242

Control board (main board)

E241 DC controller boardE242 DC controller boardE243 Operation panel boardE243 Operation panelE400 DC controller, ADF board or 24VE400 DC controller or document feed boardE500 DC controller or sorter boardE500 DC controller, sorter board or 24VE510 Finisher; feed motor, pulse sensor, finisher boardE510 FinisherE520 Finisher; stack motor, stack tray sensor, finisher boardE520 Finisher

E530 FinisherE530 Finisher; guide plate motor, stapler guide, finisher boardE531 FinisherE531 Finisher; staple motor, staple sensor, finisher board.EOO1 High fuser temperatureEOOO Low fuser temperature


E000

The temperature of the upper fixing roller has not increased above the specified level 90 secondsafter switching power on. The temperature of the upper fixing roller does not reach 150 C within 8minutes after switching power ON. The temperature of the upper fixing roller does not reach 180 Cwithin 5 minutes of reaching 150 C. The temperature of the upper fixing roller drops below 50 Cduring STANDBY.

E001 The temperature of the upper fixing roller exceeds 250 C.E005 The length of fixing assembly cleaning belt wound on the take-up reel exceeds the specified length.

E010 When two or more clock pulses are not inputted for a period of 2 seconds after a MAIN MOTORDRIVE command is generated.

E011When excessive current is detected by the fault detection circuit of the DC driver PCB. Whenexcessive current is detected by the fault detection circuit of the duplexing unit driver PCB. Whenexcessive current is detected by the fault detection circuit of the scanner motor driver PCB.

E020 When a toner out signal (TSP) is emitted from the developing assembly for a total of at least twominutes.

E050When the HOLDING TRAY HOME POSITION signal (THP) is not generated within 4 seconds fromthe beginning of HOLDING TRAY MOTOR DRIVE command (TMDP1,2) When the HOLDING TRAYHOME POSITION signal (THP) is generated for at least one second while the HOLDING TRAYMOTOR DRIVE command (TMDSP1,2) is being generated.

E203 When two or more clock pulses are not inputted from the SCANNER MOTOR DRIVE command isbeing generated.

E210When the LENS HOME POSITION signal (LHP) is not generated within 4.8 seconds after the powerswitch or door switch goes ON. When the LENS HOME POSITION signal (LHP) is generated for 2seconds or more.

E243 When an abnormally in communication occurs between the microprocessors on the DC controllerPCB and those on the control panel PCB.

E400 When an abnormality in communication occurs between the DC controller PCB detect RDF controllerPCB.

E401 When a flag mounted on the pick-up roller HOME position sensor (S3), it indicates that M1 is turning.S3 should go ON and OFF two or more times in one second.E402 The number of pulses in a 200 ms period is too low.E403 When the number of feed motor clock pulses in a 200 ms period is less than the correct value.E411 When the sensor output is greater than 2.3V when there is paper.

E500 When an abnormality in communication occurs between the DC controller PCB of sorter detect maincontroller PCB.E510 When there is no pulse output from the feed roller motor and when the first copy jams.

E540 The lead can HOME position sensor does not go "OFF" within 0.5 second after the BIN MOTORDRIVE signal (BMON) is output.

E541 The lead can HOME position sensor does not go "ON" within 1.0 second after the lead cam positionsensor goes "OFF".

E710 When an abnormality in communication occurs between the DC controller PCB and the RF controllerPCB or sorter controller PCB detect DC controller PCB.


E000The surface temperature of the fixing assembly upper roller fails to rise by a specified value within 90sec after power-on. The surface temperature of the fixing assembly upper roller fails to reach 150 Cwithin 8 min after power-on.

E001 The surface temperature of the fixing assembly upper roller exceeds 250 C.E005 The cleaning belt inside the fixing assembly has been taken up more than a specified length.E010 After generation of the main motor drive signal, two or more pulses are not received within 2 sec.E013 The error detection circuit on the waste toner feed motor driver PCB has detected an overcurrent.

E020 The accumulative time during which the toner supply signal (TSP) has been generated by thedeveloping assembly reaches 3 min*.

E050The holding tray home position signal (THP) is not generated within 4 sec while the holding traymotor drive signal (TMDP1, 2) is being generated. The holding tray home position signal (THP) isgenerated 1 sec or more while the holding tray motor drive signal (TMDP1, 2) is being generated.

E203 Input of two or more clock pulses is not received within 2 sec from the scanner motor drive signal isgenerated.

E210 The lens home position signal (LHP) is not generated within 4.8 sec after power switch or door switchhas gone ON. The lens home position signal (LHP) is generate 2 sec or more.E240 An error has occurred in the microprocessor on the DC controller PCB.

E243 An error has occurred in the microprocessor of the DC controller PCB and the microprocessor in thecontrol panel.

E710 An error has occurred in the communication between the DC controller PCB and the controller PCBof the option, and the DC controller has detected the error.

E712 No communication is perceived from the RF controller PCB for 200 ms or more the communication ismonitored at all times.

Canon A-1,B1Code DescriptionE500 An error is identified in the communication between the sorter and copier.E510 The clock signal from the motor is absent for 250 ms or more.E513 The clock signal from the motor is absent for 250 ms or more.

E530 The home position sensor (P17) fails to go OFF when an equivalent of 2560 pulses of the motor drivecommand has been generated.

E531 The stapler unit swing sensor (MS9) fails to go ON within 500 ms after the motor drive command hasbeen generated. MS9 fails to go back OFF within 1000 ms after it has gone ON.

E540 The lead cam home position sensor (P12) fails to go OFF within 2000 ms after the motor drivecommand has been generated. P12 fails to go back ON within 2000 ms after it has gone OFF.

Canon C-120Code Description



Canon C-160Code DescriptionE000 Fuser thermistor, heater, thermal fuseE001 Fuser thermistor, or triacE002 Fuser thermistor, thermal fuse or triacE003 Fuser thermistor, heater, thermal fuse or triacE004 Triac or fuser won't shut offE007 Fuser film is off center or not driving properlyE010 Main motor drive problemE030 CounterE064 Composite power supply or main boardE202 Scan problemE210 Lens drive problemE220 Exposure lampE240 Main board or composite power supplyE261 Composite power supply or fluctuating powerE400 ADF communication problem to machineE402 ADF belt motor driveE404 ADF exit motorE411 ADF document detect, or registration sensor or edge sensorE500 Sorter communication problemE510 Sorter drive problemE530 Stapler guide bar motorE531 Stapler swing motorE540 Bin shift motorE541 Bin motor drive problemE710 Main boardE711 Main boardE712 Main board or communication problem with ADFE717 Main board, asst. boardU0 Initializing. Sets all user modes to factory default settingsU1 Auto clear timer. Range 1-9. Each digit=1 minuteU2 Automatic power shut off timerU3 Fine adjustment of zoom

U4 Auto cassette switchingU5 Sort or non-sort defaultU6 Cleans document feeder pickup assemblyU7 CLEAR "replace drum"U9 Auto exposure or manual exposure as default

Canon C-180Code DescriptionE000 Fuser problem. Low temperature. Lamp, thermal switch, AC driverE001 Fuser problem. High temperature. Triac, AC driver, pinched wireE004 Fuser problemE0053 SorterE030 CounterE202 ScanE210 LensE221 Exposure lamp regulator board, thermal fuse, exposure lampE400 Automatic document feederE500 SorterE710 DC controller

Canon C200DCode DescriptionE000 Fuser thermistor, heater thermal fuseE001 Fuser thermistor, or triacE002 Fuser thermistor, thermal fuse or triacE003 Fuser thermistor, heater, thermal fuse or triac.E004 Triac or fuser won't shut offE007 Fuser film is off center or not driving properly. Might be able to reset in service mode 4-407E010 Main motor drive problemE030 CounterE041 Paper deck motor, clutch or sensorE064 Composite power supply or main motor boardE202 Scan problem. Motor sensor.E210 Lens drive problemE220 Exposure lampE240 Main board or composite power supply.E260 Main board, power supply cooling fan or composite power supply.E261 Composite power supply or fluctuating power.E400 ADF communication to machine.E401 ADF pickup motor or sensor.E402 ADF belt motor driveE403 ADF feed motor or slip sensor.E404 ADF exit motorE411 ADF document detect, or registration sensor or edge sensorE500 Sorter communication problem.E510 Sorter drive problem.E530 Stapler guide bar motor.E531 Stapler swing motor.E540 Bin shift motor.E541 Bin motor drive problem.E710 Main board (DC controller.)E711 Main board (DC controller.)E712 Main board or communication problem with ADF, or ADF main board.

E717 Main board, assist board. "Replace drum": Drum waste toner is full, or drum has run 40,000 copies.Reset with user

E802 Composite power supply or DC controller.E901 Cassette feed unit board or cassette feed motor.E902 Horizontal registration problem. I think this refers to the duplex section.

J1 Feed jamJ10 Duplex exit jamJ11 Vertical jamJ12 Vertical jamJ13 Vertical jamJ14 Vertical jamJ15 Deck jamJ2 Feed jamJ3 Separation area jamJ4 Separation area jamJ5 Exit jamJ6 Exit jamJ7 Sorter jamJ8 Door open jamJ9 Cassette jamJA Cassette jamJb Cassette jamJC Cassette jamJd Duplex feed jamJE Duplex exit jamJF Duplex registration jam

Code DescriptionE000 Fuser problem. Low temperature. Lamp, thermal switch, AC driverE001 Fuser problem. High temperature. Triac, AC driver, pinched wireE004 Fuser problemE0053 SorterE030 CounterE202 ScanE210 LensE221 Exposure lamp regulator board, thermal fuse, exposure lampE400 Automatic document feederE500 SorterE710 DC controller



E000 Fuser thermistor, heater, thermal fuseE001 Fuser thermistor, or triac

Canon NP 1820/6012/6016/6025/6060

E002 Fuser thermistor, thermal fuse or triacE003 Fuser thermistor, heater, thermal fuse or triacE004 Triac or fuser won't shut offE007 Fuser film is off center or not driving properlyE010 Main motor drive problemE030 CounterE064 Composite power supply or main boardE202 Scan problemE210 Lens drive problemE220 Exposure lampE240 Main board or composite power supplyE261 Composite power supply or fluctuating powerE400 ADF communication problem to machineE402 ADF belt motor driveE404 ADF exit motorE411 ADF document detect, or registration sensor or edge sensorE500 Sorter communication problemE510 Sorter drive problemE530 Stapler guide bar motorE531 Stapler swing motorE540 Bin shift motorE541 Bin motor drive problemE710 Main boardE711 Main boardE712 Main board or communication problem with ADFE717 Main board, asst. boardU0 Initializing. Sets all user modes to factory default settingsU1 Auto clear timer. Range 1-9. Each digit=1 minuteU2 Automatic power shut off timerU3 Fine adjustment of zoomU4 Auto cassette switchingU5 Sort or non-sort defaultU6 Cleans document feeder pickup assemblyU7 CLEAR "replace drum"U9 Auto exposure or manual exposure as default

E000 Fuser did not heat upE001 Fuser temperature too highE002 Fuser temperature not rising at correct pace

E003 Fuser temperature dropsE004 SSR shortedE210 Lens home problemE212 Lens home problemE220 Exposure lamp problemE224 Blank shutter home problemE240 DC controller or composite power supply problemE400 Data communication problemE401 Pickup motor problemE402 Belt motor problemE403 Feeder motorE404 Delivery motorE411 Document detect sensorE500 Communication problem with copierE510 Feeder motorE530 Home sensorE531 Staple swing sensor problemE540 Bin shift motor rotation problemE541 Bin motorE710 DC controllerE711 Document feeder IC failureE716 Cassette feed IC failureE800 Auto power-off circuit problemE901 Cassette feed motorE902 Paper guide home sensor problemE000 The temperature of the upper fixing roller does not reach 100 C within 5 min after powering-on.E000 Low fuser temperatureE000 Fuser ProblemE001 High fuser temperatureE001 The temperature of the upper fixing assembly remains 230 C or more for 5 seconds or more.E002 Fuser temperature not rising at the correct pace

E002 The temperature of the upper fixing roller does not reach 180 C within 5 min after it has exceeded100 C.

E003 The temperature of the upper fixing roller is below 100 C or less for 5 seconds after it has reached180 C.E003 Fuser temperature not rising at the correct paceE005 Fuser cleaner belt problemE005 The length of the cleaning belt taken up (fixing assembly) is more than a specified length.E010 Drive problem (main motor)

E010 In response to the main motor drive signal, two or more clock pulses are not generated within 1second.E013 Toner waste problem

E013 When rotation of waste toner feeder screw becomes disabled and the sensor switch (SW20) ispressed.

E020During copying operation, the black toner supply signal is "0" (no toner) for 3 min or more. At time ofinstallation, the black toner supply signal does not go "1" within 6 min during black toner supplysequence.

E020 No toner being fed for 3 min after toner was called forE030 A counter open circuit is identified when counter drive is OFF.E030 Counter

E050 The tray home position signal (THP) is not generated within 4 sec while the paper guide motor divesignal is generated.E050 Duplex problemE203 Scan home problem

E203 The scanner home position signal (SCHP) is generated 2 pulses or more within 0.5 sec when thescanner motor is turned ON.

E210 The lens x home position signal (LXHP) is not generated within 9 sec after the power switch or thedoor switch is turned ON. The lens x home position signal (LXHP) is generated for 2 sec or more.E210 Lens home problemE212 Lens home problem

E212 The lens y home position signal (LYHP) is not generated within 9 sec after the power switch or thedoor switch is turned ON. The lens y home position signal (LYHP) is generated for 2 sec or more.E400 Communication problem with copierE401 Pickup motor or motor sensorE402 Belt motor or motor sensorE403 Feed motor or motor sensorE404 exit motor or motor sensorE405 Pick up motor sensorE406 Side guard motor or motor sensorE407 Tray motor or position sensorE411 Sensor for document detectionE431 Sub registration sensorE441 MotorE442 Cooling fan problemE446 CFF mirror motor or sensorE447 CFF out of position or bad position sensorE500 Communication problem with copierE510 Feed motor driveE513 Tandem feed motor driveE530 Staple guide motor or sensor

E531 Stapler swing motorE540 Bin shifting motorE710 Q124 on the DC controller PCB cannot be initialized at power-on.E710 DC controller (main board)E711 DC controllerE711 Q124 on the DC controller is faulty after power-on.E712 The communication IC on the RDF-A1 controller is faulty.E712 24 volt power supply or RDF-A1 main boardE715 The communication IC on the C.F.F. controller PCB is faulty.E715 Computer form feeder board problem

E800 An open circuit is identified in the auto power-off mechanism. The auto power-off signal is generatedtwice or more in 2 sec.E800 Auto power shut off problem. Main boardE2 ScannerEO Heat lamp

E000 Fuser thermistor, heater thermal fuseE001 Fuser thermistor, or triacE002 Fuser thermistor, thermal fuse or triacE003 Fuser thermistor, heater, thermal fuse or triac.E004 Triac or fuser won't shut offE007 Fuser film is off center or not driving properly. Might be able to reset in service mode 4-407E010 Main motor drive problemE030 CounterE041 Paper deck motor, clutch or sensorE064 Composite power supply or main motor boardE202 Scan problem. Motor sensor.E210 Lens drive problemE220 Exposure lampE240 Main board or composite power supply.E260 Main board, power supply cooling fan or composite power supply.E261 Composite power supply or fluctuating power.E400 ADF communication to machine.E401 ADF pickup motor or sensor.E402 ADF belt motor driveE403 ADF feed motor or slip sensor.E404 ADF exit motorE411 ADF document detect, or registration sensor or edge sensorE500 Sorter communication problem.E510 Sorter drive problem.

E530 Stapler guide bar motor.E531 Stapler swing motor.E540 Bin shift motor.E541 Bin motor drive problem.E710 Main board (DC controller.)E711 Main board (DC controller.)E712 Main board or communication problem with ADF, or ADF main board.

E717 Main board, assist board. "Replace drum": Drum waste toner is full, or drum has run 40,000 copies.Reset with userE802 Composite power supply or DC controller.E901 Cassette feed unit board or cassette feed motor.E902 Horizontal registration problem. I think this refers to the duplex section.


Canon NP112Code Description


Canon NP6521Code DescriptionE000 Fuser thermistor, heater thermal fuseE001 Fuser thermistor, or triacE002 Fuser thermistor, thermal fuse or triacE003 Fuser thermistor, heater, thermal fuse or triac.E004 Triac or fuser won't shut offE007 Fuser film is off center or not driving properly. Might be able to reset in service mode 4-407E010 Main motor drive problemE030 CounterE041 Paper deck motor, clutch or sensorE064 Composite power supply or main motor boardE202 Scan problem. Motor sensor.E210 Lens drive problemE220 Exposure lampE240 Main board or composite power supply.E260 Main board, power supply cooling fan or composite power supply.E261 Composite power supply or fluctuating power.E400 ADF communication to machine.E401 ADF pickup motor or sensor.E402 ADF belt motor driveE403 ADF feed motor or slip sensor.E404 ADF exit motorE411 ADF document detect, or registration sensor or edge sensorE500 Sorter communication problem.E510 Sorter drive problem.E530 Stapler guide bar motor.E531 Stapler swing motor.E540 Bin shift motor.E541 Bin motor drive problem.E710 Main board (DC controller.)E711 Main board (DC controller.)E712 Main board or communication problem with ADF, or ADF main board.

E717 Main board, assist board. "Replace drum": Drum waste toner is full, or drum has run 40,000 copies.Reset with user

E802 Composite power supply or DC controller.E901 Cassette feed unit board or cassette feed motor.E902 Horizontal registration problem. I think this refers to the duplex section.


Canon PC 710/850Code Description



E000 Fuser thermistor, heater, thermal fuseE001 Fuser thermistor, or triacE002 Fuser thermistor, thermal fuse or triacE003 Fuser thermistor, heater, thermal fuse or triacE004 Triac or fuser won't shut offE007 Fuser film is off center or not driving properlyE010 Main motor drive problemE030 CounterE064 Composite power supply or main boardE202 Scan problemE210 Lens drive problemE220 Exposure lampE240 Main board or composite power supply

E261 Composite power supply or fluctuating powerE400 ADF communication problem to machineE402 ADF belt motor driveE404 ADF exit motorE411 ADF document detect, or registration sensor or edge sensorE500 Sorter communication problemE510 Sorter drive problemE530 Stapler guide bar motorE531 Stapler swing motorE540 Bin shift motorE541 Bin motor drive problemE710 Main boardE711 Main boardE712 Main board or communication problem with ADFE717 Main board, asst. boardU0 Initializing. Sets all user modes to factory default settingsU1 Auto clear timer. Range 1-9. Each digit=1 minuteU2 Automatic power shut off timerU3 Fine adjustment of zoomU4 Auto cassette switchingU5 Sort or non-sort defaultU6 Cleans document feeder pickup assemblyU7 CLEAR "replace drum"U9 Auto exposure or manual exposure as defaultE1 The heater film has gone off center. Turn machine off & on, make sure it's level etc.E2 Scan problmeE6 Exposure lamp or exposure lamp sensorEO Heater problemE1 The heater film has gone off center. Turn machine off & on, make sure it's level etc.E2 Scan problmeE6 Exposure lamp or exposure lamp sensorEO Heater problemE2 ScanEO HeaterE2 ScanEO HeaterE1 The heater film has gone off center. Turn machine off & on, make sure it's level etc.E2 Scan problme

E6 Exposure lamp or exposure lamp sensorEO Heater problemE2 ScanEO Heater

E000 Fuser problemE001 Fuser problemE010 DriveE210 Zoom/lens/motor problem

E00 Heater, thermoswitch, exit sensor (Reset by jumping CP102 pins 1 & 2, or leave machine off for 20secondsE001 Shorted thermistor or high-temperature, Exit sensorE010 Clock PulseE210 Zoom Lens Problem

Canon PC-1Code Description


Canon PC3Code Description

E2 ScanEO Heater


E2 ScanEO HeaterE2 ScanEO Heater

Canon PC5LCode Description

E2 ScanEO Heater

Canon PC6Code DescriptionE000 Fuser problemE001 Fuser problemE010 DriveE210 Zoom/lens/motor problem


E00 Heater, thermoswitch, exit sensor (Reset by jumping CP102 pins 1 & 2, or leave machine off for 20secondsE001 Shorted thermistor or high-temperature, Exit sensorE010 Clock PulseE210 Zoom Lens Problem

Gestetner 2217ZDCode Description

C2 Drive problemC3 Scan problemC4 Lens problemC5 CoronasC6 Heater problem or only 1 of the 2 front door interlocks switches is actuatedCO Main board problem Run simulation 90. Try power off/on

Konica 1015Konica 1018Konica 1112Konica 1120Konica 1212Konica 1290Konica 1290REKonica 1590Konica 1790Konica 2020Konica 2028Konica 2125Konica 2130Konica 2203Konica 2290Konica 2590Konica 3035Konica 3135Konica 3240

Konica 3290Konica 3340Konica 4045Konica 4065Konica 4145Konica 4155Konica 4255Konica 4290Konica 4345Konica 4355Konica 5080Konica 6090Konica 7490

Konica 1015Code DescriptionF09 Power leakage of some kind. Heat, exposure, AC or power supply.F23 Toner motor

F26Toner density adjustment problem. This means machine is undertoned. To repair, replace developerand enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel thatyou should disconnect the toner motor first. This code happens probably because either machinewasn't set up properly, or the customer kept on using the machine with the toner light on.

F28 Corona problem. Could be any corona. Must reset with "25: mode, "P45" set to "0"F34 High fuser temperature*F35 Low fuser temperature*F36 Low fuser temperature*F41 Scan homeF42 Scan homeF43 Exposure lampF45 Lens problemF54 Fan motorF60 ADF to main board communication problemF67 ADF encoderF77 Sorter gateF88 AE adjustment problemJ11 Feed jamJ12 Feed jamJ13 Feed jamJ16 Jam insideJ31 Exit jamJ32 Exit jamJ61 ADF jamJ62 ADF jamJ63 ADF exit jamJ72 Sorter jamP20 Drum unit or toner level connection problem

P25 300 copies have been run since toner light came on. Depending on how 25 mode, code 92 is set,machine may not work at all.P26 Must adjust TDS????in 47 modeP64 ADF & operator are confused

P68 ADF feed problemP69 ADF feed problemP71 Sorter interlockP81 Key counter not installed

Konica 1018Code DescriptionF18 Paper lift did not completeF23 Toner motorF24 Pre clean lamp problemF26 Toner density sensorF34 Fuser overheatF35 Fuser temperature too low. Lamp, thermofuse open wireF36 Fuser temperature erratic. Probably thermistorF41 End of scan sensor not actuatedF42 End of scan sensor not reachedF43 CVR (copy lamp voltage regulator)F45 Lens or mirror movement problemF52 Drive problemF55 Zero cross.F56 Waste toner collector box is full. After replacing it, you must enter code 94 in the 47 mode to resetF60 ADF/machine interface problemF67 ADF drive problemF70 Sorter/machine interface problemF77 Sorter bin problemF78 Stapler problemF86 Waste toner see 56F98 Duplex problemJ11 Upper cassetteJ12 Lower cassetteJ13 Paper feed jamJ14 Paper feed jamJ15 Duplex unit jamJ16 Feed jamJ17 Feed jamJ19 Paper feed jamJ31 Exit jamJ32 Exit jamJ61 ADF opened during run

J62 ADF jamJ63 ADF jamJ65 RADF reverse jamJ72 Sorter jam, or sorter interlock openedJ75 Stapler jamJ92 Duplex stack gate sensor or other duplex problemJ93 Duplex stack gate sensor or other duplex problemJ94 Duplex stack gate sensor or other duplex problemJ95 Duplex motor or duplex jamP17 Right doorP19 Right door of paper feed unitP20 Drum not installed properly or toner level sensor connection problemP33 Left doorP61 RADF reverse cover openP64 ADF was selected at the wrong timeP71 Sorter interlockP74 Stapler overloaded, or paper left in stapler binP76 Out of staplesP81 Key counter not installedP82 Memory card problemP96 Paper in stacker when duplex selectedP97 Used bypass in duplex modeP99 More than one side than the other in duplex

Konica 1112Code Description

16 Feed jam20 Toner level detector problem or loose connection23 Toner feed problem25 Toner. Means that 100 copies have been made since toner light came on26 Toner density problem31 Exit jam32 Exit jam34 Fuser temperature too high35 Fuser temperature too low36 Fuser problem. Heat, thermistor, etc.41 Scan return42 Scan forward43 Exposure lamp50 Problem with IC852 Encoder (pulse sensor, PT; drive problem)


04 PTC heater. Don't know what this is, but "0" means it is not installed. 1 means it is.

F09 Power leakage of some kind. Heat, exposure, AC or power supply or main relay. Go to "25 mode"and select "P49" and reset to "0"F23 Toner motor

F26Toner density adjustment problem. This means the machine is undertoned. To repair, replacedeveloper and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Somefeel you should disconnect the toner motor first. This code happens probably because either themachine wasn't set up properly, or because the customer kept using the machine with the light on.

F28 Corona problem. Could be any corona.F34 High fuser temperature.F35 Low fuser temperature.F36 Low fuser temperature.F41 Scan homeF42 Scan homeF43 Exposure lamp or exp. Lamp board.F44 Lens drive problem.F45 Lens problem.F54 Fan motor.F60 ADF to main board communication problem.F67 ADF encoder (pulse sensor, drive problem)F70 Sorter to machine communication problem.F77 Sorter gate.F88 AE adjustment problem.J11 Feed jamJ12 Feed jamJ13 Feed jamJ14 Jam insideJ15 Jam insideJ16 Jam insideJ31 Exit jamJ32 Exit jamJ61 ADF jamJ62 ADF jamJ63 ADF exit jam

J72 Sorter jamP11 Count. For total count, select "0". For developer count, select "5".P12 Preheat mode fuser temperature. 0 for 365 degrees. 1 for 374 degrees. 2 for 383 degrees.P15 Size priority. 0 is standard. 1 is a size priority.P16 Paper size priority.P19 Preheat shut off timing. 0 for 1 hour. 1 for 2 hours. 2 for 3 hours.P20 Drum unit or toner level connection problem. Most likely, a loose connection.P22 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.P23 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.P24 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.

P25 300 copies have been run since toner light came on, depending on how 25 mode, code 92 is set,machine may not work at all.P26 ADF border erase. 0 for none. 5 for 5mm.P26 Must replace and calibrate developer.P27 PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.P27 Toner density sensor unplugged or toner density sensor problem.P28 PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.P64 ADF & operator are confused. Remove original.P68 ADF feed problem.P69 ADF feed problem.P71 Sorter interlock.P81 Key counter not installed.


04 PTC heater. Don't know what this is, but "0" means it is not installed. 1 means it is.

F09 Power leakage of some kind. Heat, exposure, AC or power supply or main relay. Go to "25 mode"and select "P49" and reset to "0"F23 Toner motor

F26Toner density adjustment problem. This means the machine is undertoned. To repair, replacedeveloper and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Somefeel you should disconnect the toner motor first. This code happens probably because either themachine wasn't set up properly, or because the customer kept using the machine with the light on.

F28 Corona problem. Could be any corona.F34 High fuser temperature.F35 Low fuser temperature.F36 Low fuser temperature.F41 Scan homeF43 Exposure lamp or exp. Lamp board.F44 Lens drive problem.F45 Lens problem.F54 Fan motor.F60 ADF to main board communication problem.F67 ADF encoder (pulse sensor, drive problem)F70 Sorter to machine communication problem.F77 Sorter gate.F88 AE adjustment problem.J11 Feed jamJ12 Feed jamJ13 Feed jamJ14 Jam insideJ15 Jam insideJ16 Jam insideJ31 Exit jamJ32 Exit jamJ61 ADF jamJ62 ADF jamJ63 ADF exit jamJ72 Sorter jam

P11 Count. For total count, select "0". For developer count, select "5".P12 Preheat mode fuser temperature. 0 for 365 degrees. 1 for 374 degrees. 2 for 383 degrees.P15 Size priority. 0 is standard. 1 is a size priority.P16 Paper size priority.P19 Preheat shut off timing. 0 for 1 hour. 1 for 2 hours. 2 for 3 hours.P20 Drum unit or toner level connection problem. Most likely, a loose connection.P22 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.P23 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.P24 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.

P25 300 copies have been run since toner light came on, depending on how 25 mode, code 92 is set,machine may not work at all.P26 ADF border erase. 0 for none. 5 for 5mm.P26 Must replace and calibrate developer.P27 PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.P27 Toner density sensor unplugged or toner density sensor problem.P28 PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.P64 ADF & operator are confused. Remove original.P68 ADF feed problem.P69 ADF feed problem.P71 Sorter interlock.


16 Feed jam20 Toner sensor connector25 Toner light has been on for 100 copies26 Toner density sensor31 Exit switch not actuated32 Exit jam34 Fuser problem35 Low fuser temperature36 High fuser temperature41 Scan did not return home42 Scan problem43 Exposure lamp problem50 Board problem52 Drive problem85 No waste bottle16 Feed jam20 Toner sensor connector25 Toner light has been on for 100 copies26 Toner density sensor31 Exit switch not actuated32 Exit jam34 Fuser problem35 Low fuser temperature36 High fuser temperature41 Scan did not return home42 Scan problem43 Exposure lamp problem50 Board problem52 Drive problem85 No waste bottle

Konica 1290RECode Description

16 Feed jam20 Toner sensor connector25 Toner light has been on for 100 copies26 Toner density sensor31 Exit switch not actuated32 Exit jam34 Fuser problem35 Low fuser temperature36 High fuser temperature41 Scan did not return home42 Scan problem43 Exposure lamp problem50 Board problem52 Drive problem85 No waste bottle

Konica 1590Code DescriptionF23 Toner motor problemF24 Pre-clean lampF26 Toner ratioF34 High fuser temperatureF35 Low fuser temperatureF36 ThermistorF41 Scan homeF42 Forward scan exposure lampF43 Exposure lampF45 Lens driveF50 Board problemF52 DriveF77 Sorter bin sensorJ12 Paper feed jamJ13 Paper feed jamJ16 Paper feed jamJ31 Jam under drumJ32 Exit jamJ72 Sorter jamP20 Drum not installed properlyP71 Sorter cover

Konica 1790Code DescriptionF34 High fuser temperatureF35 Low fuser temperatureF36 Open thermistor or incomplete warm upF41 Scan home problemF42 Scan problemF43 CVR board problemF45 Lens driveF52 DriveF55 Zero cross problemF67 ADF driveF77 Sorter driveJ11 Upper cassette jamJ12 Lower cassette jamJ14 LCT jamJ16 Cassette jamJ31 Jam under drumJ32 Jam under drumJ62 ADF jamJ63 ADF jamJ72 Sorter jamP14 LCT openP61 ADF upP64 Original on glassP69 ADF original jamP71 Sorter cover openP81 Key counter out

Konica 2125Code DescriptionF18 Paper feed lift problem

F18-3 LCT problemF18-4 LCT problemF28-1 Charge coronaF28-2 Transfer or separator coronaF34-1 High fuser temperatureF34-2 High fuser temperatureF35-1 Low fuser temperatureF35-2 Low fuser temperatureF36-1 Low fuser temperatureF36-2 Low fuser temperatureF41 Scan return problemF42 Scan forward problemF43 Exposure lamp board problemF45 Lens home problemF52 Main motor drive problemF55 Zero cross of DC power supplyF60 Communication interruption between the machine and RADFF67 RDH or RADF drive problemF70 Communication problem between machine and sorterF77 Sorter bin problemF78 No memory card installedF86 Too many copies were made after toner waste was full. Reset with 47 mode, code 94.F98 Duplex guide plate does not return home quickly enoughJ10 Feed jamJ11 Upper feed jamJ12 Lower feed jamJ13 Upper paper feed unit jamJ14 Lower paper feed unit jamJ15 Lower paper feed unit jamJ16 Jam in machineJ17 Jam in machine

J19 Paper feed unit jamJ21 Jam around drumJ31 Exit jamJ32 Exit jamJ61 RDH/RADF jam or openJ62 RDH/RADF jamJ63 RADF exit jamJ72 Sorter jam or open interlockJ74 Finisher problemJ75 Stapler problemJ92 Duplex jamJ93 Duplex jamJ94 Duplex jamJ95 Duplex jamP17 Right side door openP19 Paper feed unit door openP33 Exit door openP51 Front door openP61 RADF cover openP64 RADF not opened to remove originalsP68 Original removed during operation of RADFP69 Original didn't feed during RADF/RDH operationP71 Sorter interlock

P74 51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originalswere used in the staple mode, or more than 25 copies per bin were attempted by the stapler.P76 Out of staplesP78 Stapler not installedP81 Key counter not plugged in

P82 Memory card not installed, not formatted to Konica specs, or no machine serial number registered onmemory cardP86 No toner waste boxP91 Duplex unit pulled outP96 Paper in duplex trayP97 Bypass was used or attempted during duplex.P99 Too many reverse side copies during duplex


F18-3 LCT problemF18-4 LCT problemF28-1 Charge coronaF28-2 Transfer or separator coronaF34-1 High fuser temperatureF34-2 High fuser temperatureF35-1 Low fuser temperatureF35-2 Low fuser temperatureF36-1 Low fuser temperatureF36-2 Low fuser temperatureF41 Scan return problemF42 Scan forward problemF43 Exposure lamp board problemF45 Lens home problemF52 Main motor drive problemF55 Zero cross of DC power supplyF60 Communication interruption between the machine and RADFF67 RDH or RADF drive problemF70 Communication problem between machine and sorterF77 Sorter bin problemF78 No memory card installedF86 Too many copies were made after toner waste was full. Reset with 47 mode, code 94.F98 Duplex guide plate does not return home quickly enoughJ10 Feed jamJ11 Upper feed jamJ12 Lower feed jamJ13 Upper paper feed unit jamJ14 Lower paper feed unit jamJ15 Lower paper feed unit jamJ16 Jam in machineJ17 Jam in machine

J19 Paper feed unit jamJ21 Jam around drumJ31 Exit jamJ32 Exit jamJ61 RDH/RADF jam or openJ62 RDH/RADF jamJ63 RADF exit jamJ72 Sorter jam or open interlockJ74 Finisher problemJ75 Stapler problemJ92 Duplex jamJ93 Duplex jamJ94 Duplex jamJ95 Duplex jamP17 Right side door openP19 Paper feed unit door openP33 Exit door openP51 Front door openP61 RADF cover openP64 RADF not opened to remove originalsP68 Original removed during operation of RADFP69 Original didn't feed during RADF/RDH operationP71 Sorter interlock

P74 51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originalswere used in the staple mode, or more than 25 copies per bin were attempted by the stapler.P76 Out of staplesP78 Stapler not installedP81 Key counter not plugged in

P82 Memory card not installed, not formatted to Konica specs, or no machine serial number registered onmemory cardP86 No toner waste boxP91 Duplex unit pulled outP96 Paper in duplex trayP97 Bypass was used or attempted during duplex.P99 Too many reverse side copies during duplex

Konica 2203Code DescriptionF35 Low TemperatureF41 OpticsF42 OpticsF43 CVRF46 Lens driveF51 DoorF52 DriveJ11 Upper PF jamJ12 Lower PF jamJ13 JamJ21 Separator jamJ31 Transport jamJ32 JamP81 Key counter


1 Sort jam61 ADF/RADF open door64 Original on glass97 Duplex paper wrong size selected99 Duplex fed double

F35 FuserF36 FuserF41 Scan returnF42 Scan forward problemF43 Exposure stays onF46 Lens position problemF52 DriveF53 Developer unit shift problemF67 ADF/RADF drive problemF98 Duplex side to side gate problemJ11 Upper cassette jamJ12 Lower cassette jamJ13 LCT jamJ14 JamJ15 Paper feed jamJ21 Jam under/around drumJ31 Transport jamJ32 Exit ajmJ61 RADF jamJ62 ADFJ63 ADF exit jamJ65 ADFJ72 Sort jam

J92-J96 Duplex jamsP81 Key counter

Konica 2590Code DescriptionF34 High fuser temperatureF35 Low fuser temperature at warm upF36 Low fuser temperature after warm upF41 No scanF42 No return scanF43 Exposure lamp stays onF45 LensF52 DriveF55 Zero cross signal to main boardF67 ADF driveF77 Sorter driveF98 Duplex problemJ11 Bypass jamJ12 Middle cassette jamJ13 Lower cassette jamJ14 LCT jamJ15 Duplex jamJ16 Paper feed jamJ17 Registration jamJ31 Internal jamJ32 Exit jamJ61 ADF opened during runADF jamJ62 ADF exit jamJ63 ADF exit jamJ65 RADF jamJ72 Sorter jam

J92-J96 Duplex jamsP14 LCT cover openP61 RADF cover openP64 Original on glassP69 RADF jam in sheet feet modeP71 Sorter cover open

P81 Key counterP96 Paper still in duplex trayP97 Wrong size selected for duplexP99 Duplex confused by double fed originals


F18-3 LCT problemF18-4 LCT problemF28-1 Charge coronaF28-2 Transfer or separator coronaF34-1 High fuser temperatureF34-2 High fuser temperatureF35-1 Low fuser temperatureF35-2 Low fuser temperatureF36-1 Low fuser temperatureF36-2 Low fuser temperatureF41 Scan problemF42 Scan forward problemF43 Exposure lamp board problemF45 Lens home problemF52 Main motor drive problemF55 Zero cross of DC power supplyF60 Communication interruption between machine and RADFF67 RDH or RADF drive problemF70 Communication problem between machine and sorterF77 Sorter, finisher, or stapler problemF86 Too many copies were made after toner waste was fullF98 Duplex problemJ10 Feed jamJ11 Jam in machineJ12 Jam in machineJ13 LCT jamJ14 LCT jamJ15 Duplex feed jamJ16 Jam in machineJ17 Jam in machineJ19 LCT jam

J21 Jam around drumJ31 Jam in machineJ32 Exit jamJ61 RDH/RADF jamJ62 RDH/RADF jamJ63 RADF exit jamJ72 Sorter jam or open interlockJ74 Finisher problemJ75 Stapler problemJ92 Duplex jamJ93 Duplex jamJ94 Duplex jamJ95 Duplex jamP17 Paper feed door openP19 LCT door openP33 Exit door openP51 Front door openP61 RADF cover openP64 RADF not opened to remove originalsP64 RDH original width different with guide widthP68 Original removed during operation or RADFP69 Original didn't feed during RADF/RDH operationP71 Sorter interlock

P74 51 copies or more went into the stapler or paper was in the so

all copier error codes

Documents