opterna datasheets 2
Post on 24-Jul-2016
259 Views
Preview:
DESCRIPTION
TRANSCRIPT
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSFC8rev1Visit: Opterna.com
Fiber Optic Outdoor Drop Cable
Opterna outdoor flat drop cable is constructed with one or two single mode fiber (ITU-T G.652D). The cable is protected by a dielectric strength member made of fiberglass reinforced plastic (FRP), steel wire and a LSZH outer jacket.
Designed for outdoor installation the cable is well suited for connections between the dome closure and small dwelling unit/ warehouse and independent villas.
Utilizing a 250μm fiber, the cable unit is suitable for use with industry standard connector.
Introduction
• Robust and lightweight
• Colour coded fibers for easy identification
• LSZH jacket for internal use
• Standard cable length of 1 Km
Features: Fiber Optic Outdoor Drop Cable
OSP Solutions
1/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSFC5rev1Visit: Opterna.com
Fiber Optic Outdoor Drop Cable
• FTTx applications
• CCTV
• ITU.T G.652D / G.657A
Applications:
Standards:
Cable Construction:
Color of Buffer:
Transmission Performance:
OSP Solutions
Parameter Value
Primary Coating Color Layer 250 ± 15 μm
Dielectric Strength Member FRPØ 0.45 ± 0.05mm
Dielectric Strength Member Steel WireØ 1.2 ± 0.05mm
Outer Jacket LSZH
1 core Drop Cable 01 Blue -
2 core Drop Cable 01 Blue 02 Orange
Fiber Types Maximum Attenuation: Value
G.652D/G.657A1 @1310nm@1550nm
0.4dB/km0.3dB/km
Maximum Dispersion ps/nm/km ≤3.5@1285~1339nm≤18@1550nm
Cutoff Wavelength nm <1260
Mode Field Diameter μm 9.2 ± 0.5@1310nm10.5 ± 0.8@1550nm
Core Clad Concentricity μm ≤0.5
Cladding Diameter μm 125 ± 1
2/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSFC5rev1Visit: Opterna.comVisit: Opterna.com
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
OSP Solutions
Fiber Optic Outdoor Drop Cable
Mechanical & Environmental:
Cable Properties:
Ordering Info:
XXX : OS1, OS2, 7A1, 7A2, 7B2, 7B3YYY : 001, 002
Temperature Range -40⁰C to +60⁰C
Fire Performance IEC 60332-1, IEC 60754-2 & IEC 61034
FC-XXX-DRP-SW-YYY-LZ Fiber Optic Singlemode Outdoor Drop Cable, LSZH
FC-XXX-DRP-SW-YYY-PV Fiber Optic Singlemode Outdoor Drop Cable, PVC
SheathColor
FiberCount
NominalDiameter
[mm]
NominalWeight
[Kg/Km]
Maximum Tensile Load Minimum Bend Radius Crush Resistance
Short Term
[N]
Long Term
[N]
Loaded[mm]
Installed[mm]
Short Term
[N]
Long Term
[N]652D 657A 652D 657A
Black 1 or 2 2.0×3.0 ± 0.2mm 15.6 600 300 60 50 30 20 1000 500
3/32/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSCArev1 1/4
Fiber Optic Patchcords and Pigtails
Opterna offers high performance patchcords and pigtails for use in all types of fiber optic networks. The Opterna® patchcords & pigtails are manufactured using state-of-the-art controlled manufacturing processes to operate over a wide range of wavelengths, ranging from 850nm - 1300nm for Multimode and 1310nm - 1550nm for Singlemode fiber. Opterna patchcords and pigtails are terminated with high quality connectors, which provide low insertion loss and high return loss. Each patchcord or pigtail is individually tested and supplied with test certificates. The unique serial number provides traceability of every single product.
Introduction
• Available in singlemode and multimode fiber types
• Available with all fiber optic connector types
• High quality ferrules and housings
• Low insertion loss and high return loss
• Individual test results and unique trace number provided with every product
• Mating Durability: 1000 cycles; <0.2 dB change
• Temperature range: -40 °C to +70°C
• RoHS compliant
• IEC, EIA/TIA and GR-326-CORE compliant
Features Patchcords and Pigtails
Fiber Interconnect & Passives
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSCArev1 2/4
Patchcords and Pigtails
• Datacenter and Datacom
• FTTX deployments
• Pre-terminated assembly interconnection
• CATV, WAN, LAN and Telecom networks
• Testing and measurement equipment
Fiber Interconnect & Passives
Applications:
Size & Dimensions:
Chan. 2
Chan. 1
End 1
Chan. 1
Chan. 2
End 2
L
l 2
End 2
Fig.2: Simplex patchcord schematic
Fig.1: Duplex patchcord schematic
End 1
L
l 2
Fig.3: Pigtail schematic
Length of assembly (L) L -0/+100mm (for L<0.5.m)
L -0/+150mm (for 0.5m>L<5m)
L -0/+200mm (for L>5m)
Split length (l1) - only for duplex 150 ± 25mm
Traceability label distance (l2) 200 ± 25mm (from one end)
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSCArev1 3/4
Visit: Opterna.com
Parameter SpecificationFiber Types Multimode: OM1, OM2, OM3, OM4
Singlemode: G652D, G657A1, G657A2, G657B2, G657B3, G655Cable type Simplex: 2.8, 2.0, 1.8, 0.9, 0.6, 0.250mm
Duplex: 2.8, 2.0, 1.8mmFlat duplex: 2.8mm
Cable Colours Blue, Yellow, White, Orange, Aqua, Heather VioletConnector Types SC, LC, MU, FC, ST, MTRJ, ESCON, E-2000, SMA, FDDI
Endface Finish PC, UPC, APC
Parameter Connector Type Max TypicalInsertion loss (dB) Multimode SC, LC, MU, FC, ST, E-2000, ESCON, FDDI 0.30 0.20
Multimode MTRJ & SMA 0.75 0.50Singlemode SC, LC, MU, FC, ST, ESCON, FDDI 0.30 0.20
E2000 0.25 0.12MTRJ 0.50 0.30
Return Loss (dB) All types Singlemode UPC endface finish type 50 55All types Singlemode APC endface finish type 60 65
General Specification:
Optical performance specification:
Patchcords and PigtailsFiber Interconnect
& Passives
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSCArev1 4/4
Ordering Info:
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
CA
Connector TypeEnd 1
ConnectorFinish End 1
CableDiameter
Fiber Type Cable Type CableMaterial
Connector TypeEnd 2
ConnectorFinish End 2
CableLength
CableColour
ST ST connector
P PC 16 1.6mm OM1 62.5/125MM
SX Simplex L LSZH ST ST connector
P PC 005 0.5meter
BL Blue
SC SC connector
U UPC 18 1.8mm OM2 50/125MM
DX Duplex V PVC SC SC connector
U UPC 015 1.5meter
YL Yellow
SD SC duplex A APC 20 2.0mm OM3 50/125 MMLaserOptimized
FD FlatDuplex
R RISER SD SC duplex A APC 150 15meter
WH White
FC FC connector
28 2.8mm OM4 50/125 MMLaserOptimized
TB TightBuffered
P PLENUM FC FC connector
Blank forpigtail
OR Orange
LC LC connector
02 250um OS2 9/125 SMG.652D
ES Easy strip
LC LC connector
AQ Aqua
LD LC duplex 06 600um 7A1 G-657A1 SMBendinsensitive
LT Loose tube
LD LC duplex HV HeatherViolet
MU MUconnector
09 900um 7A2 G-657A2 SMBendinsensitive
MU MUconnector
MD MU duplex
7B2 G-657B2 SMBendinsensitive
MD MU duplex
E2 E-2000connector
7B3 G-657B3 SMBendinsensitive
E2 E-2000connector
MT MTRJconnector
655 9/125 SMG-655
MT MTRJconnector
FD FDDIconnector
FD FDDIconnector
ES ESCONconnector
ES ESCONconnector
SM SMAconnector
SM SMAconnector
Blank forpigtail
Fiber Interconnect & Passives
Patchcords and Pigtails
OpternaROpternaR
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
Visit: Opterna.com
Fused 1x2 (2 x2) Splitters
Opterna High Performance Bidirectional Single Mode Splitters are used to split light from one fiber into two output fiber lines with ultra low loss. It also can be used to combine light from two fibers into one. It is a compact, fused, all fiber technology device. Manufactured using state-of-the-art Fused Bi-conical Taper process (FBT), they exhibit uniform performance over entire optical spectrum from 1260 to 1600nm with near zero loss. The epoxyfree optical path provides good power handling capability.
Opterna fused splitter uses highly reliable and specialized packaging technology, providing excellet thermal stability and long life. The advanced packing ensures very good stability under vibration and impact, making these splitters ideal for outdoor applications. Opterna splitters are available in both 1x2 and 2x2 configuration with different package and connector types to cater most applications.
Introduction
• All fiber technology • Bidirectional • Triple Play • Ultra broadband 1260 ~ 1600nm • Extreme stability to thermal variations• Tap coupler versions of any split ratio • Near Zero Excess Loss • Low Back Reflection • Low Polarization Dependant Loss • Excellent Uniformity• Compact Packaging • Designed to comply GR-1209-CORE and GR-1221-CORE • 100% rigorous screening (rapid temperature cycling) and testing • Variety of package and pigtail options• Factory connectorization available• Custom Packaging available
Features: Fused 1x2 (2 x2) Splitters
OSP Solutions
DSCP1rev1 1/3
OpternaROpternaR
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
Visit: Opterna.com
Fused 1x2 (2 x2) Splitters
• FTTX• Telecommunication Networks• CATV Networks• Fiber Optic Sensors• Optical Fiber Communication Systems
*other coupling ratios are also available†All insertion loss are excluding connector loss
Applications:
Specifications
OSP Solutions
Parameter Narrow Band single Window
Wide Band singleWindow
Narrow Band single Window
Wide Band singleWindow
OperatingWavelength
1310±20nm or1550±20nm or
1585±20nm
1310±40nm or 1550±40nm or 1530-1610nm (for DWDM)
1310±20nm and 1550±20nm
1310&1550(±40nm) or1260- 1360 & 1480-
1580nm
Grade Premium Standard Premium Standard Premium Standard Premium Standard
Excess Loss : Typical 0.1 dB 0.2 dB 0.1 dB 0.2 dB 0.1 dB 0.2 dB 0.1 dB 0.2 dB
Insertion Loss : Maximum (Loss of high power port/ Loss of low power port)*
50/50 3.4 dB 3.6 dB 3.4 dB 3.6 dB 3.6 dB 3.8 dB 3.6 dB* 3.8 dB*
55/45 3.0/3.9 dB 3.2/ 4.1 dB 3.0/ 3.9 dB 3.2/ 4.1 dB 3.1/ 4.0 dB 3.3/ 4.2 dB 3.2/ 4.1 dB 3.4/ 4.3 dB
60/40 2.5/ 4.4 dB 2.7/ 4.6 dB 2.5/ 4.4 dB 2.7/ 4.6 dB 2.6/ 4.6 dB 2.8/ 4.8 dB 2.7/ 4.7 dB 2.9/ 4.9 dB
65/35 2.1/ 5.1 dB 2.3/ 5.3 dB 2.1/ 5.1 dB 2.3/ 5.3 dB 2.2/ 5.2 dB 2.4/ 5.4 dB 2.3/ 5.3 dB 2.5/ 5.5 dB
70/30 1.8/ 5.6 dB 2.0/ 5.8 dB 1.8/ 5.6 dB 2.0/ 5.8 dB 1.9/ 5.8 dB 2.1/ 6.0 dB 2.0/ 6.0 dB 2.2/ 6.2 dB
75/25 1.7/ 6.5 dB 1.9/ 6.7 dB 1.7/ 6.5 dB 1.9/ 6.7 dB 1.7/ 6.6 dB 1.9/ 6.8 dB 1.8/ 6.8 dB 2.0/ 7.0 dB
80/20 1.2/ 7.5 dB 1.4/ 7.7 dB 1.2/ 7.5 dB 1.4/ 7.7 dB 1.3/ 7.6 dB 1.4/ 7.8 dB 1.3/ 7.8 dB 1.5/ 8.0 dB
85/15 1/ 8.8 dB 1.2/ 9.0 dB 1/ 8.8 dB 1.2/ 9.0 dB 1.0/ 9.0 dB 1.1/ 9.2 dB 1.0/ 9.2 dB 1.2/ 9.4 dB
90/10 0.7/ 10.8 dB 0.8/ 11.0 dB 0.8/ 11.0 dB 0.9/ 11.5 dB 0.8/ 11.1 dB 0.9/ 11.6 dB 0.8/ 11.0 dB 0.9/ 11.5 dB
95/5 0.4/ 13.8 dB 0.5/ 14.0 dB 0.5/ 14.0 dB 0.6/ 14.5 dB 0.5/ 14.2 dB 0.6/ 14.7 dB 0.5/ 14.0 dB 0.6/ 14.2 dB
98/2 0.3/ 18.0 dB 0.3/ 18.5 dB 0.35/18.5dB 0.4/ 19.0 dB 0.35/18.7dB 0.4/ 19.2 dB 0.3/ 18.5 dB 0.4/ 18.7 dB
99/1 0.2/ 21.5 dB 0.3/ 22.0 dB 0.3/ 22.1 dB 0.4/ 22.5 dB 0.3/ 22.4 dB 0.4/ 22.8 dB 0.3/ 22.0 dB 0.35/22.3dB
Uniformity, max(for 50/50) 0.6 dB 0.8 dB 0.6 dB 0.8 dB 0.7 dB 0.8 dB 0.8 dB* 1.0 dB*
PDL max 0.2 dB
Directivity >50 dB
Operating Temperature -40 to + 85°C
Fiber Type G 652D
Dimensions, LD 2.9 mm (dia) x 51 mm (L), bare fiber
,MD 3.05mm (dia) x 65mm (L), 900um hytrel tubing
,HD Plastic Housing, 96.5mm(I) x 12mm (b) x 10mm (t),mm jacketed cable
DSCP1rev1 2/3
OpternaROpternaR
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
Visit: Opterna.comVisit: Opterna.com
Spectral Response Chart
Ordering Info:
OSP Solutions
Fused 1x2 (2 x2) Splitters
7
6
5
4
3
2
1
0
1230 1280 1330 1380 1430 1480 1530 1580 1630
Wavelength (nm)
Insertion Loss
B d
CP
Split Ratio Grade PortConfiguration
Package Type Wavelength in nm Connector Type Connector Finish
Lead Length
50 50:50 P Premium 12 1 x 2Splitter
L Light Duty, 250μmBuffered fiber
13NB 1310 ± 20nm NO NoConnector
N No connector
10 1m ± 0.1m
45 55:45 S Standard 22 2 x 2Splitter
M Medium Duty,900μm Tubing
15NB 1550 ± 20nm ST STconnector
U UPC 15 1.5m ± 0.1mand so on
40 60:40 C Custom Type*
J Heavy Duty, 2mmJacketed
35NB 1310 ± 20 &1550 ± 20nm
SC SCconnector
A APC 00 For Modularversions
H Heavy Duty, 3mmJacketed
58NB 1585 ± 20nm FC FCconnector
A AluminiumCassette
13WB 1310 ± 40nm LC LCconnector
P Moulded PlasticCassette
15WB 1550 ± 40nm MU MUconnector
C Custom Module* 35WB 1310 ± 40 &1550 ± 40nm
E2 E-2000connector
G LGX Module NWBB 1260 - 1360 &1480 - 1580nm
WDBB 1260 - 1360 &1450 - 1600nm
ULBB 1260 - 1610nm
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
DSCP1rev1 3/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSOMMrev1 1/3
Fused Multimode Splitters
Opterna High Performance Bidirectional Multimode Splitters are used to split light from one fiber into two output fiber lines with ultra low loss. It also can be used to combine light from two fibers into one. It is a compact, fused, all fiber technology device. They are manufactured using state-of-the-art Fused Bi-conical Taper process (FBT) on graded index fibers with core diameters of 50um or 62.5um. Opterna’s Multimode splitters are commonly used in short distance communications with LED sources operating at 1310nm or 850nm. They are wavelength independent over a broad range of wavelengths with uniform modal power distribution launch condition.
Opterna’s MM fused splitters use highly reliable and specialized packaging technology, providing excellent thermal stability and long life. Opterna splitters are available in both 1x2 and 2x2 configuration with different package and connector types to cater most applications.
Introduction
• All fiber technology
• Bidirectional
• Accurate split ratio
• Ultra-low excess loss
• Excellent directivity
• Available in 50/125, 62.5/125 & OM3
• Tap Ratios available
• Extreme stability to thermal variations
• Excellent Uniformity
• Compact Packaging
• Variety of package and pigtail options
• Factory connectorization available
• Custom Packaging available
Features Fused Multimode Splitters
Fiber Interconnect & Passives
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSOMMrev1 2/3
Fused Multimode Splitters
• Fiber Optic Sensors• LAN• Short distance transmission• Video Networks• Signal Monitoring• Network Monitoring
Fiber Interconnect & Passives
Applications:
Specifications:
Fiber Type 62.5/125μm OR 50/125μm
Operating Wavelength 850 and 1300nm
Split Ratio* 50:50
Maximum Insertion Loss 3.7dB (Without Connector)
Directivity > 40dB
Operating Temperature -400C to +850C
PackageLight Duty Stainless steel tube, 3.05mm (dia) x 55mm (L)
Medium Duty Stainless steel tube, 3.05mm (dia) x 65mm (L)
Heavy Duty Plastic Housing, 96.5mm (l) x 12mm (b) x 10mm (t)
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSADrev1 3/3
Visit: Opterna.com
Ordering Info:
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
OMMC
Split Ratio Fiber Type PortConfiguration
Package Type Wavelengthin nm
Connector Type Lead length
50 50:50 6 62.5/125 12 1 x 2Splitter
L Light Duty,250μm Buffered fiber
85NB 850 ± 20nm NO NoConnector
10 1m ± 0.1m
55 55:45 5 50/125 22 2 x 2Splitter
M MediumDuty, 900μmTubing
13NB 1300 ± 20nm ST STConnector
15 1.5m ± 0.1mand so on
60 60:40 &so on
3 OM3 J Heavy Duty,2mmJacketed
1385 1310 ± 20 &850 ± 20nm
SC SCConnector
00 For Modularversions
H Heavy Duty,3mmJacketed
AQ Aqua FC FCConnector
A AluminiumCassette
HV Heather violet LC LCConnector
P Moulded Plastic Cassette
BK Black
C Custom* ME Metal
G LGX Module
Fiber Interconnect & Passives
Fused Multimode Splitters
OpternaROpternaR
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
Visit: Opterna.com
Fused Wideband Tap Couplers
Opterna High Performance Tap Couplers are used to tap light from a fiber line, to monitor the signals. It is used in Erbium doped fiber amplifiers (EDFA) and telecommunication networks for monitoring the signal strength of different channels. Manufactured using state-of the- art Fused Bi-conical Taper process (FBT), they exhibit uniform performance over entire optical spectrum from 1260 to 1600nm with near zero loss. The epoxyfree optical path provides good power handling capability.
Opterna Tap couplers use highly reliable and specialized packaging technology, providing excellent thermal stability and long life. The advanced packing ensures very good stability under vibration and impact, making these splitters ideal for outdoor applications. Opterna tap couplers are available in both 1x2 and 2x2 configuration with different package and connector types to cater most applications.
Introduction
• Available with different tap ratios from 1 to 10%
• All fiber technology (fused)
• Broadband performance
• Extreme stability to thermal variations
• Tap coupler versions of any split ratio
• Near Zero Excess Loss
• Low Back Reflection
• Low Polarization Dependant Loss
• Compact Packaging
• Designed to comply GR-1209-CORE and GR-1221-CORE
• 100% rigorous screening (rapid temperature cycling) and testing
• Variety of package and pigtail options
• Factory connectorization available
Features: Fused Wideband Tap Couplers
OSP Solutions
DSCP2rev1 1/3
OpternaROpternaR
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
Visit: Opterna.com
Fused Wideband Tap Couplers
• EDFA signal monitoring• Network channel strength monitoring• FTTx• Telecom & CATV Networks• Fiber Optic Test & Sensing Equipment
†All insertion loss are excluding connector loss
Applications:
Specifications
OSP Solutions
Parameter Single window /C -Band/L -Band
Dual Window C +L B and for DWDM
OperatingWavelength
1530-1570nm or 1570-1610nmor 1310±20nm
1310±20nm and 1550±20nm 1530-1610nm
Grade Premium Standard Premium Standard Premium Standard
Excess Loss : Typical 0.1 dB 0.2 dB 0.1 dB 0.2 dB 0.1 dB 0.2 dB
Insertion Loss : Maximum (Loss of high power port/ Loss of low power port)*
90/10 0.7/ 10.8 dB 0.8/ 11.0 dB 0.8/ 11.0 dB 0.9/ 11.5 dB 0.8/ 11.0 dB 0.9/ 11.5 dB
95/5 0.4/ 13.8 dB 0.5/ 14.0 dB 0.5/ 14.0 dB 0.6/ 14.5 dB 0.5/ 14.0 dB 0.6/ 14.2 dB
98/2 0.3/ 18.0 dB 0.3/18.5 dB 0.35/ 18.5 dB 0.4/ 19.0 dB 0.3/18.5 dB 0.4/18.7 dB
99/1 0.2/ 21.5 dB 0.3/ 22.0 dB 0.3/ 22.1 dB 0.4/ 22.5 dB 0.3/ 22.0 dB 0.35/ 22.3 dB
Max Loss Variation in the tap leg90/10 0.3 dB 0.5 dB 0.5 dB 0.7 dB 0.5 dB 0.7 dB
95/5 0.4 dB 0.6 dB 0.6 dB 0.8 dB 0.6 dB 0.8 dB
98/2 0.4 dB 0.6 dB 0.6 dB 0.8 dB 0.6 dB 0.8 dB
99/1 0.4 dB 0.6 dB 0.6 dB 0.8 dB 0.6 dB 0.8 dB
PDL max 0.2 dB
Directivity >³55 dB
Reflectance -60 dB for Premium grade (<-55dB for Standard Grade)
Operating Temperature -40 to +85 °C
Storage Temperature -40 to +70 °C
Fiber Type SMF-28 or SMF-28e
Dimensions, LD 2.9mm (dia) x 51mm (L)
,MD 3.05mm (dia) x 65mm (L)
,HD Plastic Housing, 96.5mm (l) x 12mm (b) x 10mm (t)
DSCP2rev1 2/3
OpternaROpternaR
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
Visit: Opterna.comVisit: Opterna.com
Spectral Response Chart
Ordering Info:
OSP Solutions
Fused Wideband Tap Couplers
CP
CouplingRatio
Grade PortConfiguration
Package Type Wavelength in nm Connector Type Connector Finish
Lead Length
10 90:10 P Premium 12 1 x 2Splitter
L Light Duty, 250μmBuffered fiber
13NB 1310 ± 20nm NO NoConnector
N No connector
10 1m ± 0.1m
05 95:05 S Standard 22 2 x 2Splitter
M Medium Duty,900μm Tubing
15NB 1550 ± 20nm ST STconnector
U UPC 15 1.5m ± 0.1mand so on
01 99:01 C Custom Type*
J Heavy Duty, 2mmJacketed
35NB 1310 ± 20 &1550 ± 20nm
SC SCconnector
A APC 00 For Modularversions
H Heavy Duty, 3mmJacketed
13WB 1310 ± 40nm FC FCconnector
A AluminiumCassette
15WB 1550 ± 40nm LC LCconnector
P Moulded PlasticCassette
35WB 1310 ± 40 &1550 ± 40nm
MU MUconnector
C Custom Module* E2 E-2000connector
G LGX Module
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
0
5
10
15
20
25
1530 1540 1550 1560 1570
W avelength (nm)
-0.2
0
0.2
0.4
0.6
0.8
1
Tap Port High Power Port
High
Power
Port
IL
Tap
Port
IL
Insertion Loss: 99/1 Tap Coupler
DSCP2rev1 3/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSMCrev1 1/3
Mode Conditioning Patchcords
Opterna Mode Conditioning Patchcord (MCP) is designed for long wave (LX) multimode applications of Gigabit Ethernet. It is compliant with the IEEE 802.3z application standard. The purpose of Mode Conditioning Patchcord is to condition the launch to ensure specified link lengths and it should be inserted on both ends of a link to interface between a single mode adapter card and a multimode cable plant. They are used to minimize Differential Mode Delay (DMD) which can occur when a singlemode laser source is launched into the center of a multimode fiber.
The most common use for MCP is long wave Gigabit Ethernet applications (1000BASE-LX) in which a 1310nm single mode transceiver is being deployed into an existing multimode fiber plant. Opterna MCP uses the most reliable offset method that launches laser source away from the center of the multimode fiber. This ensures effective bandwidth for the system, closer to that measured by over-filled launch method.
Opterna MCP assembly offers the same reliability of a standard patchcord. They are available in all connector styles with 2.5 or 1.25mm ferrules and common multimode fiber types (50 & 62.5ìm).
Introduction
• Designed for 1000BASE-LX Transmitters (GbE)
• Available in 50/125 and 62.5/125 fiber options
• Fully compliant with IEEE 802.3z
• Eliminates differential mode delay
• Available in all connector options
• Compact and reliable packaging
• Uses offset method to ensure reliability and are 100% tested for Coupled Power Ratio (CPR)
• Individual test sheet with IL & CPR and unique product identification number for traceability
• RoHS compliant
• Low Insertion Loss & Back Reflection
Features Mode Conditioning Patchcords
Fiber Interconnect & Passives
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSMCrev1 2/3
Mode Conditioning Patchcords
• Gigabit Ethernet 1000BASE-LX over multimode cable
Parameter SpecificationDescription 62.5 μm MMF 50 μm MMFOperating wavelength 1310 nmMaximum Insertion loss 0.4 dBCoupled Power Ratio (CPR) 28<CPR<40 dB 28<CPR<40 dBReturn Loss (RL) SM channel >30 dB
MM channel >20 dBOffset between SMF and MMF 17<Offset<23 μm 10<Offset<16 μmConnector finish UPC (RL>50dB) or APC (RL> 60dB)
Ferrule Geometry Radius of Curvature 10 to 25mmApex offset ≤ 50μmFiber height -50 ≤ Ht < 50nm
Maximum Angular Offset 1 DegreeConnector options SC, ST, FC, LC, MU, E -2000, MTRJOperating temperature -40 to + 80°C
Fiber Interconnect & Passives
Applications:
Specifications:
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSMCrev1 3/3
Visit: Opterna.com
Parameter SpecificationDescription 62.5 μm MMF 50 μm MMFOperating wavelength 1310 nmMaximum Insertion loss 0.4 dBCoupled Power Ratio (CPR) 28<CPR<40 dB 28<CPR<40 dBReturn Loss (RL) SM channel >30 dB
MM channel >20 dBOffset between SMF and MMF 17<Offset<23 μm 10<Offset<16 μmConnector finish UPC (RL>50dB) or APC (RL> 60dB)
Ferrule Geometry Radius of Curvature 10 to 25mmApex offset ≤ 50μmFiber height -50 ≤ Ht < 50nm
Maximum Angular Offset 1 DegreeConnector options SC, ST, FC, LC, MU, E -2000, MTRJOperating temperature -40 to + 80°C
MC
Fiber Type Connector-Cable Plant
End
Cable Type Equipment End-
MM Leg
Equipment End-
SM Leg
Connector Finish
(SM leg)
Equipment End
Connector Configuration
Length
62 62.5/125 MM
ST ST connector
16 1.6mmduplex
ST ST connector
ST ST connector
U UPC SX Simplex 015 1.5 meter
50 50/125 MM
SC SC connector
18 1.8mmduplex
SC SC connector
SC SC connector
A APC DX Duplex 105 B
SD SC duplex 20 2.0mmduplex
FC FC connector
FC FC connector
Not applicable(blank)
10.5 meter
FC FC connector
28 2.8mmduplex
LC LC connector
LC LC connector
LC LC connector
MU MU connector
MU MU connector
LD LC duplex E2 E-2000connector
E2 E-2000connector
MU MU connector
MT MTRJconnector
If MTRJ(blank)
MD MUduplex
E2 E-2000connector
MT MTRJconnector
Ordering Info:
Mode Conditioning PatchcordsFiber Interconnect
& Passives
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
MT Modular Cassettes & Adapter Plates
The Opterna® pre-terminated MT cassettes are ideally suited for high density backbone and building entry interconnect applications in data and telecom environments. Manufactured in our state-of-the-art facilities, they offer rapid deployment, high density and maximum space utilization combined with significant time and cost savings. The Opterna MT modular product line is easy to install, upgrade and re-work without affecting the existing connections, which makes it perfect for pay-as-you-grow scenarios.
In addition Opterna also offers a wide range of pass through modular adapter plates for patching and managing pre-terminated fiber optic cables, factory populated with all standard types of adapters.
Introduction
• All modules are LGX compatible
• Available in all fiber types - SM and MM
• 100 % factory terminated and tested - saves times and guarantees high performance
• Up to 24 FO connections in one LGX cassette
• Polarity A (standard), B or C
• Optimized performance using only highest quality connectivity components
• 40 & 100G ready
• Highest quality MT connectivity - MTP® and MTP Elite® connectors
Features Data Center Conectivity MT Modular Cassettes and Adapter Plates
OSP Solutions
DSODCCrev1 1/4
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
MT Modular Cassettes & Adapter Plates
• Data center and telecommunication networks
• High density connection between active equipment and distribution architectures
• Gigabit Ethernet, Local Area Networks, Wide Area Networks, Storage Area Networks
• Backbone links for CATV and video transmission
Parameter Average IL (dB)Rear connectors MTP or MTP Elite (MPO on request)Front connectors SC, LC (Others on request)Number of rear connectors 1 or 2Number of front connectors Up to 12 SC or 24 LC connectionsFiber types G652D, OM3, OM4 (Others on request)Cassette dimensions (HxWxD) mm 30 x 129 x 132Packed dimensions (HxWxD) mm 50 x 150 x 200
Cassette material Cold rolled steel, powder coatedCassette color Black RAL 9005, available in RAL 7032 and RAL 7035 (Gray) on requestCassette material TIA-604-5, IEC 61754-4, IEC-61754-7, IEC 61754-20, EN50377-15-1,
ISO/IEC 11801, TIA/EIA-568-B, EIA/TIA-526-7&14A, RoHS
Connector type Average IL (dB)* Max IL (dB)* Return loss (dB)MTP Elite (MM) 0.10 0.35 N/AMTP (MM) 0.20 0.60 N/ALC/ SC (MM) 0.20 0.30 N/AMTP Elite (SM) 0.10 0.35 >60MTP (SM) 0.25 0.75 >60LC/ SC (SM) 0.15 0.30 >50(UPC)/60(APC)
OSP Solutions
Applications:
DSODCCrev1 2/4
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com Visit: Opterna.com
Drawing:
104.0
132.0
29.5
128.9
30.2
6.1
15.1
117.3
R5.0
MT Modular Cassettes & Adapter PlatesOSP Solutions
DSODCCrev1 3/4
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
Ordering information MT modular cassettes:
ODCC
MT Connector
MT Connector Type
Front AdapterType
FiberCount
SleeveMaterial
Fiber Type Adapter color
Metal color
Polarity
ME MTP Elite
A 12F SC SC SX 12 12 M Metal OM3 OM3 GN Green BK Black A A
MT MTP B 24F SD SC DX 24 24 C Zirconia OM4 OM4 BL Blue B B
LD LC DX OS2 G652D BG Beige X Other
LQ LC Quad AQ Aqua
LS LC DX internalshutter
HV HeatherViolet
LH LC quad internalshutter
Ordering information modular adapter plates:
ODCA
AdapterType
Number ofAdapters
SleeveMaterial
Adapter colour
Metal colour
SC SC SX 06 6 M Metal GN Green BK Black
SD SC DX 12 12 C Zirconia BL Blue
LD LC DX Blank plate BG Beige
LQ LC Quad AQ Aqua
LS LC DX internalshutter
HV HeatherViolet
LH LC quad internalshutter
Blank plate
NA Blank plate
Ordering Info:
MT Modular Cassettes & Adapter PlatesOSP Solutions
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
DSODCCrev1 4/4
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
MT Modular Patch Panels
The MT modular patch panels are a part of Opterna’s comprehensive MT modular connectivity system for data centers and other. In order to enable the optimum balance between accessibility and density, a range of 1U and 3U fixed and sliding modular solutions are available. All panels are based on the IEC 60297-3 standard.
1U modular panel:The 1U MT modular patch panel is a cost effective solution for routing and patching array fiber optic cables (MTP/MPO). It has 3 slots for loading pre-terminated modular MT cassettes or adapter plates. When fully loaded this panel offers up to 36 SC, 72 LC or 18 MT connections in 1U. Two options are available - fixed and sliding (drawer type).
3U modular panel:The 3U Chassis has 12 slots and provides a very high density solution. It is ideal in situations where floor and rack space utilization is critical and Moves Adds and Changes (MACS) are limited. Although it is a high density solution, the 3U chassis is designed with finger access in mind, striking the optimum balance between space utilization and access. This chassis enables a maximum of 12 cassettes or adapter plates to be installed, offering up to 144 SC or 288 LC connections in 1U.In order to improve the physical security, a lockable metal cover can be installed. The cover also includes a 1U protected cable management duct.
Introduction
• Robust and reliable
• Uses industry approved 19” design and LGX style modules
• Flexible, multi-functional solution for different types of connectivity
• High density combined with ease of installation and maintenance
• No disturbance of existing connections during installation or re-work
• Recessable mounting brackets
Features Data Center Conectivity MT Modular Patch Panels
Central OfficeSolutions
DSODCPrev1 1/4
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
435.0
396.0
405.0
200.0
83.0
434.0
481.0
176.5 13
2.5
31.8
171.0
270.0
444.0
486.0
43.7
31.8
465.0
MT Modular Patch Panels
3U chassis
Fixed Panel
Drawings:
Central OfficeSolutions
DSODCPrev1 2/4
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com Visit: Opterna.com
438.2
301.5
483.0
43.0
31.8
Sliding panel
Drawings:
MT Modular Patch PanelsCentral Office
Solutions
DSODCPrev1 3/4
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
• Data center and telecommunication networks
• High density connection between active equipment and distribution architectures
• Gigabit Ethernet, Local Area Networks, Wide Area Networks, Storage Area Networks
• Backbone links for CATV and video transmission
*excluding mounting brackets
Parameter Specification 1U sliding panel High density3U panel
Cover for3U panel
Net Dimension (HxWxD)mm* 44x440x270 44x440x302 133x435x200 171x435x83Packed Dimension (HxWxD)mm 50x530x330 50x530x330 160x460x230 200 x 460 x 150Net Weight (kg) 1.9 3.7 4.2 1.8
Packed Weight (kg) 2.2 4.0 4.5 2.0Number of LGX modules 3 3 12 N/AMaterial Cold rolled steel, powder coatedColor Black RAL 9005, available in RAL 7032 and RAL 7035 (Gray) on request
Operating temperature °C -10 to +60Compliance IEC 60297, RoHS
Part Number DescriptionODCPF13BK Fixed 1U MT Modular patch panel for 3 modules, blackODCPS13BK Sliding 1U MT Modular patch panel for 3 modules, blackODCPF312BK Fixed 3U High density MT Modular patch panel for 12 modules, blackODCPF3CBK Cover for Fixed 3U High density MT Modular patch panel, blackODCPG45BK Gland holder for all MT panels (including gland for 4 cables up to 5mm)
Central OfficeSolutions
Applications:
Part Numbers:
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna nameand logo are registered trademarks of Opterna Technology Limited.
MT Modular Patch Panels
DSODCPrev1 4/4
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSFC5rev1Visit: Opterna.com
Mt Array Trunk Cable Assemblies™
The Opterna MT trunk cable assemblies are used for high density backbone cabling in data centers and other environments with high fiber density. Manufactured in our state-of-the-art facilities, they offer rapid deployment, high density and maximum space utilization combined with significant time and cost savings. The Opterna MT trunk cable assemblies are available in a wide range of multimode and single mode fiber types. The compact micro tube cables greatly reduce the total volume of cables and help to optimize the cable management.
Introduction
• Standard fiber counts of 12, 24, 48, 72 and 144 fibers, others available on request
• Available in all fiber types - SM and MM
• 100 % factory terminated and tested - saves times and guarantees high performance
• Standard LSZH outer sheath, PE and OFNP available on request
• Standard Polarity A, all other types available on request
• Optimized performance using highest quality connectivity components MTP® Standard and MTP® Elite connectors
• 40 & 100G ready
• 12 or 24 fibers in one compact MT connector
Features Data Center Conectivity MT Array Trunk Cable Assemblies
Central OfficeSolutions
3/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSFC5rev1Visit: Opterna.com
Mt Array Trunk Cable Assemblies™
• Data center and telecommunication networks
• High density connection between active equipment and distribution architectures
• Gigabit Ethernet, Local Area Networks, Wide Area Networks, Storage Area Networks
• Backbone links for CATV and video transmission
• High density FTTX applications
Parameter SpecificationFiber count 12F 24F 48F 72F 144FConnectors Female 12 or 24F MTP® or MTP Elite® (MPO on request)Cable type Micro fiber indoor cable with micro tubeFiber types G652D, OM3, OM4 (Others on request)Cable diameter (mm) 3.5 4.6* 10.6* 12.6* 19.5*Cable weight (kg/ km) 12.5 14.6 105 155 336Bending radius 20 x cable diameter (10 x cable diameter without load)
Operating temperature °C 0 to +60Compliance ISO/IEC 60793, ISO/IEC 60794, IEC 60332, TIA-604-5, IEC 61754-7, ISO/IEC 11801,
TIA-568-C, EIA/TIA-526-7&14A, RoHS* Or over sheathed individual 3.5mm 12F cables
Connector type Average IL (dB)* Max IL (dB)* Return loss (dB)MTP Elite (MM) 0.10 0.35 N/AMTP (MM) 0.20 0.60 N/AMT P Elite (SM) 0.10 0.35 >60MTP (SM) 0.25 0.75 >60
* Per mated pair
Central OfficeSolutions
Applications:
2/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSFC5rev1Visit: Opterna.com Visit: Opterna.com
ODCF ODCF ODCF ODCF ODCF ODCF ODCF
Both Sides Connector
MT Connector Type
Fiber Count Length Excluding Branches (Equal to Total Length If No Branches)
Shortest Branch Length
Fiber Type Polarity
ME MTP Elite
A 12F female
012 12 001 1 Meter
01 0.1 Meter OM3 OM3 A A
MT MTP B 24F female
024 24 010 10Meters
05 0.5 Meter OM4 OM4 B B
B 12F male
048 48 100 100Meters
10 1.0 Meter OS2 G652D X Other
B 24F male
072 72 00 No Branches XXX Other
144 144
XXX Other
Ordering Info:
Mt Array Trunk Cable Assemblies™Central Office
Solutions
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
3/32/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSODCFrev1Visit: Opterna.com
MT Fanout Cable Assemblies
The Opterna® MT hydra fanout assemblies are used to connect active equipment directly to high fiber count backbone MT cables and MT cassettes in data centers and other high density environments. Manufactured in our state-of-the-art facilities, they offer rapid deployment, high density and maximum space utilization combined with significant time and cost savings. The Opterna MT fanout cable assemblies are available in a wide range of multimode and singlemode fiber types and connectors. The compact microtube cables greatly reduce the total volume of cables and help to optimize the cable management.
Introduction
• Standard fiber counts of 12, 24, 48, 72 and 144 fibers, others available on request
• Available in all fiber types - SM and MM
• 100 % factory terminated and tested - saves times and guarantees high performance
• Standard LSZH outer sheath, PE and OFNP available on request
• Standard Polarity A, all other types available on request
• Optimized performance using highest quality connectivity components MTP® Standard and MTP® Elite connectors
• 40 & 100G ready
• 12 or 24 fibers in one compact MT connector
• Standard 2.0mm color coded fanout with SC and LC connectors, 0.9mm and other types of connectors available on request
Features Data Center Conectivity MT FanoutCable Assemblies
Central OfficeSolutions
1/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSODCFrev1Visit: Opterna.com
MT Fanout Cable Assemblies
• Data center and telecommunication networks
• High density connection between active equipment and distribution architectures
• Gigabit Ethernet, Local Area Networks, Wide Area Networks, Storage Area Networks
• Backbone links for CATV and video transmission
• High density FTTX applications
Parameter SpecificationMT Connectors Female 12 or 24F MTP or MTP Elite (MPO on request)Fanout connectors SC or LC, others available on requestCable type Microfiber indoor cable with microtubeFiber types G652D, OM3, OM4 (Others on request)Cable diameter (mm) 12F - 3.5 24F - 4.6Cable weight (kg/ km) 12.5 14.6Bending radius 20 x cable diameter (10 x cable diameter without load)
Operating temperature °C 0 to +60Compliance ISO/IEC 60793, ISO/IEC 60794, IEC 60332, TIA-604-5, IEC 61754-7,
IEC 61754-4, IEC 61754-20, ISO/IEC 11801, EIA/TIA-526-7&14A, RoHS
Connector type Average IL (dB)* Max IL (dB)* Return loss (dB)MTP Elite (MM) 0.10 0.35 N/AMTP (MM) 0.20 0.60 N/ALC/ SC (MM) 0.20 0.30 N/AMTP Elite (SM) 0.10 0.35 >60MTP (SM) 0.25 0.75 >60LC/ SC (SM) 0.15 0.30 >55(UPC)/60(APC)
* Per mated pair
Central OfficeSolutions
Applications:
2/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSODCFrev1Visit: Opterna.com Visit: Opterna.com
ODCF ODCF ODCF ODCF ODCF ODCF ODCF ODCF
MT Connector
Type
MT Connector Type
Fan-out connector
Type(APC /UPC/ PC)
Length excluding
Fanout
Shortest Branch Length
Fiber Type Connectorcolor
Polarity
ME MTP Elite
A 12F female
SCA SC/APC SX 010 1 Meter
01 0.1 Meter OM3 OM3 GN Green A A
MT MTP B 24F female
SCU SC/UPC SX 015 1.5 meter
05 0.5 Meter OM4 OM4 BL Blue B B
C 12F male
SCP SC MM SX 150 15 meters
10 1.0 Meter OS2 G652D BG Beige X Other
D 24F male
LCA LC/ APC SX 7A1 G657A1 HV HV
LCU LC/ UPC SX 7A2 G657A2 AQ Aqua
LCP LC MM SX
SDA SC/APC DX
SDU SC/UPC DX
SDP SC MM DX
LDA LC/ APC DX
LDU LC/ UPC DX
LDP LC MM DX
Ordering Info:
MT Fanout Cable AssembliesCentral Office
Solutions
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
3/32/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSFC4rev1Visit: Opterna.com
Fiber Optic Loose Tube Cable
Opterna fiber optic loose tube cable features a central tube design surrounded by glass yarn. This dielectric single jacket central loose tube cable is a UV-stabilized and fully water blocked cable for outdoor duct applications (PE outer jacket) or Indoor/Outdoor applications (LSZH outer jacket).
The loose tube design provides stable and highly reliable transmission parameters for a variety of voice, data, video and imaging applications.
Introduction
• Central loose tube construction
• Lightweight
• Compact design for limited conduit space
• Each fiber is color coded for easy identification
• Glass yarns for limited rodent protection
• LSZH jacket for Indoor/outdoor applications
• RoHS compliant
Features: All Dielectric Single Jacketed Central Tube
OSP Solutions
RipcordOuter Jacket
12-Fiber Cable
24-Fiber Cable
Optical FiberFilling CompoundLoose Buffer tubes
Glass Yarns
RipcordOuter Jacket
Optical FiberFilling CompoundLoose Buffer tubes
Glass Yarns
1/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSFC4rev1Visit: Opterna.com
Fiber Optic Loose Tube Cable
• Building Interconnections (Campus LAN)
• Telcordia GR-20-CORE
• IEC 60793 / IEC 60794
• ITU-T G.652.D
• Fiber - Singlemode OS2 - G.652.D, 62.5μm (OM1), 50μm (OM2,OM3 & OM4) multimode available• Outer jacket : Black UV- and moisture-resistant Polyethylene or LSZH (Low Smoke Zero Halogen)
Applications:
Standards:
Options:
Color of Buffer:
Transmission Performance:
OSP Solutions
Optical Fiber 62.5/125 μmOM1
(850/1300)
50/125 μmOM2
(850/1300)
50/125 μmOM3
(850/1300)
50/125 μmOM4
(850/1300)
9/125 μmOS2
(1310/1550)
Attenuation (dB/km) Typical values 3.5/1.0 3.0/1.0 3.0/1.0 3.0/1.0 0.40/0.30
Minimum Bandwidth (MHz •km) 200/500 500/500 1500/500 3500/500 -
Ethernet Link Distance (m)
10Gbps - - 300 550 -
1Gbps 275/550 550/550 - - -
01 - Blue 07 - Red 13 - Blue / Single dot marking 19 - Red / Single dot marking
02 - Orange 08 - Black 14 - Orange / Single dot marking 20 - Natural
03 - Green 09 - Yellow 15 - Green / Single dot marking 21 - Yellow / Single dot marking
04 - Brown 10 - Violet 16 - Brown / Single dot marking 22 - Violet / Single dot marking
05 - Slate 11 - Rose 17 - Slate / Single dot marking 23 - Rose / Single dot marking
06 - White 12 - Aqua 18 - White / Single dot marking 24 - Aqua / Single dot marking
2/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSFC4rev1Visit: Opterna.comVisit: Opterna.com
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
OSP Solutions
Fiber Optic Loose Tube Cable
Mechanical Characteristics:
Ordering Info:
Shipping Information:
FiberCount
NominalDiameter
NominalWeight
Maximum Tensile Load Crush Load Minimum Bend Radius
Short Term Long Term Short Term Long Term Loaded Installed
[mm] [kg/km] [N] [N] [N/cm] [N/cm] [mm] [mm]
2 6.3 36 1600 800 200 100 130 65
4 6.3 36 1600 800 200 100 130 65
6 6.3 36 1600 800 200 100 130 65
8 6.3 36 1600 800 200 100 130 65
12 6.3 36 1600 800 200 100 130 65
16 6.8 40 1600 800 200 100 140 70
18 6.8 40 1600 800 200 100 140 70
24 6.8 40 1600 800 200 100 140 70
Storage Temperature : -40 to + 75°C / Operating Temperature : -20 to + 70°C
XXX : OS1, OS2, OM1, OM2, OM3, OM4YYY : Number Of cores
*Other Cable lengths may be available upon request
FC-XXX-CLT-GA-YYY-LZ Fiber Optic Single Jacket Central Loose Tube, glass yarn, LSZH jacket
FC-XXX-CLT-GA-YYY-PE Fiber Optic Single Jacket Central Loose Tube, glass yarn, PE jacket
FC-XXX-CLT-GA-YYY-NR Fiber Optic Single Jacket Central Loose Tube, glass yarn, riser rated jacket
FC-XXX-CLT-GA-YYY-NP Fiber Optic Single Jacket Central Loose Tube, glass yarn, plenum rated jacket
Standard Reel Length 4000m
3/32/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSODB1rev1 1/2
ODB Series 100
Opterna’s Optical Distribution Box (ODB) Series 100 is a robust outdoor-rated enclosure designed for FTTH networks in single dwelling, multi-dwelling and multi-tenant applications, where it serves as a distribution box for up to 8 subscribers.
Available in two sizes, the ODB 100 features an internal swing panel with a rear splice area that accommodates PLC splitters, splices and excess fiber storage. The front face of the swing panel holds SC duplex or LC quad connector adaptors. The ODB 100 can be securely mounted to a surface with 4 screws, accessible only when the cover is open.
Introduction
• Indoor and outdoor applications, IP 55 rated • Compact and light, made of UV resistant polycarbonate • Swing panel design for easy installation and maintenance • Integrated holder for one PLC splitter • Integrated splice tray and fiber management • Distribution cables can be pre-terminated or spliced to pigtails • Lock with protective cap • Connectivity compliance: IEC 61754-4, IEC 61754-20, GR-326 CORE
Features Robust Outdoor-rated Enclosure
OSP Solutions
OpternaROpternaR
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
Visit: Opterna.comDSODB1rev1 2/2
ODB Series 100
• FTTH networks serving single dwelling, multi-dwelling and multi-tenant buildings
• Wall, pole or pedestal mount
Note: Maximum of 2 Adapters in 1A enclosure.
Splitters, pigtails and additional splice trays are sold separately. Contact Opterna for details.
Applications:
Specifications:
Ordering Info:
OSP Solutions
Parameter Unit 1A enclosure 1B enclosureDimensions (HxWxD) in. 8.1 x 6.3 x 3.6 8.1 x 7.9 x 3.6
mm 206 x 160 x 91 206 x 200 x 91Input Cable ports - 1 PG13.5 (5 to 9mm dia.) 2 PG16 (10 to 14mm dia.)
Output cable ports - 8 (2 to 7mm dia.) 8 (2 to 7mm dia.)Number of adapters - 2 SC duplex or LC quad 4 SC duplex or LC quad
Splitter capacity - 1 2Splice capacity - 10 12
Water and dust resistance - IEC 60529 (IPX5, IP5X)Impact resistance - IEC 62262 (IK08)
Operating temperature - -20 to +65
Color - RAL-7016 (Anthracite Grey)
Enclosure Type Adapter Quantity
Adapter Type
Termination Color
AG
ODB1A 1A enclosure 0 none 0 none 0 none
ODB1B 1B enclosure 1 one SD SC Duplex A APC
2 two LQ LC Quad U UPC
3 three
4 four
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSPLCrev1
Visit: Opterna.com
PLC Splitters
Opterna’s Planar Lightwave Circuits (PLC) splitters are manufactured using silica glass waveguide circuits and extremely precise alignment of optic fibers in very small package. They split or combine light from one or two incoming fibres to multiple numbers of outgoing fibers. They perform uniformly over a wide spectral range, with ultra-low losses. Opterna splitters are highly compact, reliable and available in very wide range of fiber and connector types. All Opterna PLC splitters are fully compliant with the Telcordia GR-1209 & GR-1221 standard.
Introduction
• Low insertion losses • Ultra-broadband performance (1250-1650nm)
• Low Polarization Dependant Loses (PDL) and Polarization Mode Dispersion (PMD)
• 1 or 2 input channels and up to 64 output channels
• Ultra small, suitable for all applications
• Available with all type of packages and connectors
Features PLC Splitters
Central OfficeSolutions
1/4
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSPLCrev1Visit: Opterna.com
PLC Splitters
• FTTx networks
• Optical CATV networks
• CWDM and DWDM systems
• Key element of all PON networks
• LAN and Telecom networks
Parameter Unit 1 x N1 x 2 1 x 4 1 x 8 1 x 16 1 x 32 1 x 64
Insertion Loss Max. dB. 3.8 7.0 10.4 13.9 17.2 22.0
Channel Uniformity Max. dB. 0.6 0.5 0.5 1.4 1.6 2.5
Polarization Dependent Loss Max. dB. 0.2 0.3 0.3 0.3 0.3 0.3
Wavelength Dependent Loss Max. dB. 0.3 0.3 0.3 0.3 0.3 0.3Temperature Dependent Loss Max. dB. 0.5 0.5 0.5 0.5 0.5 0.5
Connector Dependent Loss Max. dB. 0.2 0.2 0.2 0.2 0.2 0.2
Operating Wavelength Min.-Max. nm 1250 ~ 1650
Return Loss Min. dB. 55
Directivity Min. dB. 55
Operating Temperature °C -40 ~ + 85
Storage Temperature °C -40 ~ + 85
Maximum Input Power Max. mW 500
Fiber Type - ITU G.652D or G.657A
Fiber Length Meter 1.0 meter or customized
Connector Type - Customized (SC, SC/APC, LC, LC/APC)
Package Dimension(L x W x H)
Bare Fiber(250 μm)
mm 40x4x4 40x4x4 40x4x4 40x4x4 55x7x4 55x12x4
IntegratedPackage (900μm)
mm 55x7x4 55x7x4 55x7x4 60x12x4 80x23x4.5 120x43x4.5
Cassette mm 100x80x10 100x80x10 100x80x10 100x80x10 100x80x10 100x80x20
Central OfficeSolutions
Applications:
Specifications:
2/4
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSPLCrev1Visit: Opterna.comVisit: Opterna.com
Parameter Unit 2 x N2 x 2 2 x 4 2 x 8 2 x 16 2 x 32 2 x 64
Insertion Loss Max. dB. 4.0 7.3 10.7 14 17.5 22.5
Channel Uniformity Max. dB. 0.8 1.0 1.0 1.5 1.8 3.0
Polarization Dependent Loss Max. dB. 0.2 0.3 0.3 0.3 0.3 0.4
Wavelength Dependent Loss Max. dB. 0.3 0.3 0.3 0.3 0.3 0.3Temperature Dependent Loss Max. dB. 0.5 0.5 0.5 0.5 0.5 0.5
Connector Dependent Loss Max. dB. 0.2 0.2 0.2 0.2 0.2 0.2
Operating Wavelength Min.-Max. nm 1250 ~ 1650
Return Loss Min. dB. 55
Directivity Min. dB. 55
Operating Temperature °C -40 ~ + 85
Storage Temperature °C -40 ~ + 85
Maximum Input Power Max. mW 500
Fiber Type - ITU G.652D or G.657A
Fiber Length Meter 1.0 meter or customized
Connector Type - Customized (SC, SC/APC, LC, LC/APC)
Package Dimension(L x W x H)
Bare Fiber(250 μm)
mm 50x4x4 50x4x4 50x4x4 55x7x4 55x7x4 65x12x4
IntegratedPackage (900μm)
mm 65x7x4 65x7x4 65x7x4 75x12x4 80x23x4.5 120x43x4.5
Cassette mm 100x80x10 100x80x10 100x80x10 100x80x10 100x80x10 100x80x20
Name of the test Condition DurationTemperature- Humidity aging 85°C and 85% RH 7 daysVibration 10 - 55Hz, 1.52mm double amplitude, in three axes 1 hour
Component Impact Test Impact of 500g (mass<=0.125kg), 1ms , half sine pulse 2 impacts
Temperature Cycling Test -40°C to + 70°C , Ramp rate: 1°C /min, Dwell time >15min 10 cycles
Temperature- Humidity cycling -40°C to + 85°C , between 10°C and 23°C - 85% RH, at 85°C -20%RH,between 23°C and 85°C - maintain a linear change in RH,below 10°C - uncontrolled RH
14 days
Water Immersion 43 ± 2°C , PH 5.5 ± 0.5 7 days
Fiber Side Pull test 0.23 kg load, 90° angle , 2 directions 5 seconds
Fiber Side Pull test 0.45 Kg load for Single Input Fiber , 1.5 Kg load for8 Fiber Ribbon Outputs
5 seconds
Specifications:
Telcordia 1209 & 1221 Test results:
PLC SplittersCentral Office
Solutions
3/42/4
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSPLCrev1Visit: Opterna.com
Ordering Info:
Central OfficeSolutions
PLC Splitters
PLC PLC PLC PLC PLC PLC PLC PLC PLC
SplitRatio
PackageType
Inputconnector
Type
OutputConnector
Type
InputFiberType
OutputFiberType
InputFiberType
OutputFiberType
FiberType
102 MTP Elite A Integrated SCU SC/UPC SCU 12 0 250 0 250 05 0.5m 05 0.5m OS2 G652D fiber
104 1x2Splitter
B Plastic case100x45x10mm
SCA SC/APC SCA 24 9 900 μm 9 900 μm 10 1.0m 10 1.0m 7A1 G657A1 fiber
108 1x4Splitter
C Plastic case100x80x10mm
LCU LC/UPC LCU LC/UPC 2 2 mmLSZH
2 2 mmLSZH
50 5.0m 50 5.0m 7A2 G657A2 fiber
116 1x16Splitter
D Bare fibersplitter
LCA LC/APC LCA LC/APC X Custom R μmribbon
132 1x32Splitter
F FDH PLCmodule
FCU FC/UPC FCU FC/UPC X Custom
164 1x64Splitter
X For customtype
FCA FC/APC FCA FC/APC
202 2x2Splitter
Noconnector
Noconnector
204 2x4Splitter
XXX Custom XXX Custom
208 2x8Splitter
216 2x16Splitter
232 2x32Splitter
264 2x64Splitter
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
4/4
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSPTrev1 1/3
Opterna offers a complete range of pre-terminated multi-fiber assemblies in a variety of cable and connector configurations. Our high-quality factory terminated and tested assemblies are used for simple point to point links or to install a complete fiber optic network.
The cabling is fully compatible with all standard cable management accessories and requires no special tools or expertise to install. The cables are fitted with a protective gland to protect the connectors during installation and a special pulling head that is attached to the cable strength member allows the cable to be pulled through ducts without applying load to the terminations.
Pre-terminated assemblies can also be customized to cater the customer’s specific performance requirement, application migration plan and installation environment.
Introduction
• Fiber count up to 48 fibers
• Available in Multimode and Singlemode fiber types
• Available with indoor and outdoor cable types
• Available with all fiber connector types
• Fully tested, labeled and documented• Improved link loss budget
• Excellent tensile load resistance to facilitate cable pulling through ducts and rails
• Pulling sock at pulling end allows easiness to pull cable through race tracks
• Easy, quick and cost efficient installation
• RoHS compliant
• Complies with international telecom standards
Features Pre-terminated Multi-core Fiber Optic Assembly
Fiber Interconnect & Passives
Pre-terminated Fiber Optic Assembly
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSPTrev1 2/3
Pre-terminated Fiber Optic Assembly
• Inter-building and Intra-building backbones for Local Area Network, Data Center, Premise and Campus applications
• Data center main, horizontal, zone and equipment distribution area trunk cables for Storage Area Network (SAN) applications
Fiber Count 2, 4, 6, 8, 12, 16, 24, 48Fiber Types OM1, OM2, OM3, OM4, G652D, G657ACable Type Tight buffered (indoor)
Steel Type Armored (indoor and specific outdoor)Loose Tube (Outdoor application with water resistance
Branch out types Staggered (as in fig. 1 below) or Fan-out (equal branch lengths)Connector Types SC, FC, ST, LC, MU, E2000 (in UPC & APC finish)Specification of gland used for standard assemblies
M20 X 1.5 (other gland size available) – color: black/ grey
Insertion Loss of each termination Max: 0.50dB; Typ: 0.30B
Return Loss of each assembly (for Singlemode) >50dB for UPC>60dB for APC
Max Tensile Load 1500NPackaging Coiled and bagged for assemblies < 50m
Coiled on a drum for assemblies > 50m
Fiber Interconnect & Passives
Applications:
Size & Dimmensions:
Specifications:
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSPTrev1 3/3
Visit: Opterna.com
PT
ConnectorPulling End
ConnectorFinish
FiberCount
Fiber Type Cable Type CableJacket
Connector - NonPulling End
ConnectorFinish
Cable Length(L)
Shortest BranchLength
(L1 & L2)*
Branch CableColour
ST ST P PC 02 2
Fiber
OM1 62.5/125
MM
TB 0.9mm
Tight
Buffered
L LSZH ST ST P PC 001 1
meter
03 0.3 meter BK Black
SC SC
simplex
U UPC 04 4
Fiber
OM2 50/125
MM
LT Loose tube V PVC SC SC
simplex
U UPC 010 10
meter
30 3.0 meter YL Yellow
SD SC
duplex
A APC 06 6
Fiber
OM3 50/125
MM
BO 2mm Break
Out cable
E PE SD SC
duplex
A APC 100 100
meter
WH White
FC FC 08 8
Fiber
OM4 OM4
Fiber
E RISER FC FC No
Connecter
OR Orange
LC LC
simplex
10 10
Fiber
OS2 G652 D E PLENUM LC LC
simplex
AQ Aqua
LD LC
duplex
12 12
Fiber
7A1 G657 A1 LD LC
duplex
HV Heather
Violet
MU MU 16 16
Fiber
7A2 G657 A2 MU MU
E2 E2000 24 24
Fiber
E2 E2000
MT MTRJ 48 48
Fiber
MT MTRJ
No
connector
Ordering Info:
Pre-terminated Fiber Optic AssemblyFiber Interconnect
& Passives
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
Length of Assembly (gland to gland OR free end to gland) – L L ± 1.0 (m)
Length of shortest branch at pulling end (for staggered assembly) – l₁ 30cms (unless specified)
Length of shortest branch at non-pulling end (for staggered assembly)– l₂ 30cms (unless specified)
Incremental length between branches (for staggered assembly) – l l ± 3cms
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSCAB3rev1 1/2
Visit: Opterna.com
WALL MOUNT CABINETS - RECESSED
Opterna recessed cabinet are the administration and distribution point for voice, fax, data networking, video entertainment, internet access and all other voice / data / video home solutions. This versatile cabinet flush mounts to a wall.
The cabinets are designed to hold FTTx equipment comfortably. Opterna recessed cabinets are designed to hold 19” rack mounted equipment and are also available in non 19” formats. The cabinet features a lockable glass door, adjustable front profiles and removable gland plates at the top and bottom. Two different versions are available, fixed design and removable front cover.
Introduction
• Constructed with rigid frames that can be fitted on a wall
• Adjustable mounting rails in the front for 19” formats
• Top and bottom cable entry facility for easy cable installation
• Front section with tempered glass door and lock
• Good ventilation and heat dispersion
Features Wall Mount Cabinets- Recessed
MDU Solutions
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSCAB3rev1 2/2
Visit: Opterna.com
Wall Mount Cabinet, Single Section
• Designed for installations that comply with the
EN 50173-1, EN 50174-1 & 2,ISO/IEC 11801, ANSI/TIA/EIA-568-C
• FTTx
Standard
• Comply with mounting dimensions to IEC 297-3 and
DIN - 41494 for all equipments
Material
• SPCC cold rolled steel
• Mounting profiles - 1.2mm
• Other elements - 1.0 mm
• Front door : Tempered glass or Metal
Surface Finish
• Powder coated
Applications:
Technical Specification:
Ordering Info:
MDU Solutions
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
X : S - Fixed design, without outer frameD - With removable outer frame
Part Number Description Height (mm)
Width (mm)
Depth (mm)
CAB-RWM-12-600-150-X-G Recessed Single Section Cabinet, 12U, 600mm (W)x 150mm(D), Glass Door
WMS WMS WMS
CAB-RWM-12-600-300-S-G Recessed Single Section Cabinet, 12U, 600mm (W)x 300mm(D), Glass Door
WMS WMS WMS
CAB-RWM-600-425-120 Recessed Single Section Cabinet, 600(H) x 425(W) x 120(D) WMS WMS WMS
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSFCSrev1 1/2
Shuttered SC Patch Cables
Even when using shuttered fiber optic adapters in FTTH deployment there is a risk of accidental exposure to laser light: when the patch cable on the premises side is connected to the wall outlet but unplugged from the active equipment (ONT or ONU) the standard SC patch cables do not offer any protection. The Opterna shuttered SC patch is a unique products developed for FTTH and FTTD application. It has a spring loaded mechanism inside which secures the patch cable immediately after it is disconnected and this way eliminates this treat of exposure to the invisible laser light. Like all the The Opterna patchcords & pigtails the shuttered SC patch cords are manufactured in state-of-the-art controlled manufacturing processes to operate over a wide range of wavelengths ranging in 1310 and 1550nm windows with guaranteed low loss and reliability. Each patch cord is individually tested and supplied with test certificates. The unique serial number gives provides traceability of every single product and ensures supreme quantity.
Introduction
• Especially designed for FTTH/ FTTD applications at customers’ premises
• Product without analogue
• High quality connectors with reliable mechanism
• Low insertion loss and high Return loss
• Individual test results and unique trace number provided with every product
• High mating durability
• RoHS compliant
• Compliant with IEC 61754-4 Standar
Features Shuttered SC Patch Cables
Central OfficeSolutions
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSFCSrev1 2/2
Shuttered SC Patch Cables
• FTTH deployments
• FTTD deployments
Central OfficeSolutions
Applications:
Specifications:
Optical Performance Specification:
Ordering Info:
Parameter SpecificationFiber Types 62.5/125 (OM1), 50/125 (OM2), OM3, OM4, G652D, G657A & B
Cable Types Simplex, 3.0mm
Connector Types SC
Endface Finish PC, UPC, APC
Parameter Type of connector MeasuresParameter Multimode SC Max: 0.30db; Typical: 0.20dB
Singlemode SC Max: 0.30db; Typical: 0.20dB
Return Loss (Singlemode) Singlemode UPC endface finish type Min: 50dB; Typical 55dB
Singlemode APC endface finish type Min: 55dB; Typical 60dB
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
FCSPC FCSPC FCSPC FCSPC FCSPC
Connector TypeBoth Ends
Connector FinishBoth Ends
Fiber Type Cable Length Cable Colour
SC SC Simplex A APC OM2 FC Style 100 10 meter YL Yellow
U UPC OM3 SC Style WH White
OM4 ST Style OR Orange
OS2 LC Style HV Heather Violet
7A1 MU Style AQ Aqua
7B2 G657B2
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSSADrev1 1/3
Fiber Optic Shuttered Adapters
The Opterna shuttered adapters are designed specially to suit the high safety requirements of the FTTH networks. The shutters are designed to prevent ingress of dust and accidental laser exposure. The spring loaded shutters will remain closed when the connector is unplugged and prevents exposure to laser. All adapters are manufactured in standard colors for identifying UPC and APC end face finishing of the connectors. Opterna fiber optic adapters are manufactured strictly according the international standards, fully compatible with all types of equipment. The Opterna shuttered adapters have the same high quality optical performance as the standard non shuttered ones.
Introduction
• High performance UPC and APC adapters
• Standard rear side blue and green color
• SC Simplex, SC duplex and LC Duplex versions available
• White shutter side to suit the color of faceplate
• Bottom to top opening of shutter which makes thelaser caution label visible to the user
• Low insertion loss – under 0.2dB(connector performance dependent)
• Return loss >50dB (UPC) and >60dB(APC)
• High mating durability (<0.2dB change after 1000 cycles)
• Very wide temperature range of using (-40 to +80°C)
• RoHS compliant
Features Fiber Optic shuttered Adapters
Fiber Interconnect & Passives
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSSADrev1 2/3
Fiber Optic Shuttered AdaptersFiber Interconnect
& Passives
Applications:
Size and dimensions:
• All types of connection interface (ODF, wall mounted solutions etc.)
• FTTH deployments
• CATV, WAN, LAN and Telecom networks
• Testing and measurement equipment
SC Simplex adaptor (all dimensions in mm)
LC Duplex adaptor (all dimensions in mm)
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comDSSADrev1 3/3
Visit: Opterna.com
SAD
Adapter type End facefinish type
Sleeve type HousingColor
Shutter color Flanges Shutter type(for duplex)
SC Simplex SC U UPC C Zirconia BL Blue BL Blue F WithFlanges
S Oneshutter
SD Duplex SC A APC M Metal GN Green GN Green N Reducedflanges
E Individualshutters
LD Duplex LC P PC BG Beige BG Beige
WH White
MT Metal
Ordering Info:
Fiber Optic Shuttered AdaptersFiber Interconnect
& Passives
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSFC7rev1Visit: Opterna.com
Fiber Optic Multi Loose Tube Cable
Opterna single jacket single armor loose tube fiber optic cable provides stable and highly reliable transmission parameters for a variety of voice, data, video and imaging applications.
The cable offers durability and flexibility required for many outside plant uses where added compressive strength, rodent resistance.
RoHS (Restriction of the use of Certain Hazardous Substances Directive) Complied.
Introduction
• Multi loose tube construction
• Each fiber is color coded for easy identification
• Color coded loose tubes for easy identification
• LSZH jacket for Indoor/outdoor applications
Features: Single Jacket Single Armor Multi Loose Tube
OSP Solutions
Optical FiberJelly CompoundLoose Buffer TubesCentral Strength MemberWater Blocking Yarn or JellyCore Wrapping Tape
Outer Strength Member
Water Blocking TapeRipcordCorrugated Steel Tape ArmorOuter PE/LSZH Jacket
72-Fiber Cable
1/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSFC7rev1Visit: Opterna.com
Fiber Optic Multi Loose Tube Cable
• Building Interconnections (Campus LAN)
• FTTx & Telecommunications Networks
• Telcordia GR-20-CORE
• IEC 60793 / IEC 60794
• IEC 60332-1,3
• IEEE 383
• Fiber - Singlemode OS2 - G.652.D, 62.5μm(OM1), 50μm (OM2, OM3 & OM4) multimode available
Applications:
Standards:
Options:
Color of Buffer:
Transmission Performance:
OSP Solutions
Optical Fiber 62.5/125 μmOM1
(850/1300)
50/125 μmOM2
(850/1300)
50/125 μmOM3
(850/1300)
50/125 μmOM4
(850/1300)
9/125 μmOS2
(1310/1550)
Attenuation (dB/km) Typical values 3.5/1.0 3.0/1.0 3.0/1.0 3.0/1.0 0.40/0.30
Minimum Bandwidth (MHz •km) 200/500 500/500 1500/500 3500/500 -
Ethernet Link Distance (m)
10Gbps - - 300 550 -
1Gbps 275/550 550/550 - - -
01 - Blue 05 - Slate 09 - Yellow
02 - Orange 06 - White 10 - Violet
03 - Green 07 - Red 11 - Pink
04 - Brown 08 - Black 12 - Aqua
2/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
DSFC7rev1Visit: Opterna.comVisit: Opterna.com
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
OSP Solutions
Fiber Optic Multi Loose Tube Cable
Mechanical & Environmental:
Ordering Info:
Shipping Information:
FiberCount
NominalDiameter
NominalWeight
Maximum Tensile Load Crush Load Minimum Bend Radius
Short Term Long Term Short Term Long Term Loaded Installed
[mm] [kg/km] [N] [N] [N/cm] [N/cm] [mm] [mm]
6 12.7 157/215 2,700 1000 220 110 254 127
12 12.7 157/215 2,700 1000 220 110 254 127
24 12.7 157/215 2,700 1000 220 110 254 127
36 12.7 157/215 2,700 1000 220 110 254 127
48 13.2 163/223 2,700 1000 220 110 264 132
72 13.2 163/223 2,700 1000 220 110 264 132
96 14.3 190/260 2,700 1000 220 110 286 143
120 15.8 225/308 2,700 1000 220 110 316 158
144 17.2 260/356 2,700 1000 220 110 344 172
228 18.0 279/382 2,700 1000 220 110 360 180
276 19.2 319/437 2,700 1000 220 110 384 192
300 19.9 340/466 2,700 1000 220 110 398 199
Storage Temperature : -40 to + 75°C / Operating Temperature : -20 to + 70°C
*Denotes norminal value for PE / LSZH Jacketed Cable.
XXX : OS1, OS2, 7A1, 7A2, 7B2, 7B3, 655, OM1, OM2, OM3, OM4YYY : Number of Cores
*Other Cable lengths may be available upon request
FC-XXX-MLT-SA-YYY-PE Fiber Optic Single Jacket Armor Multi Loose Tube, PE jacket
FC-XXX-MLT-SA-YYY-LZ Fiber Optic Single Jacket Armor Multi Loose Tube, LSZH jacket
Standard Reel Length 4000m
3/32/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
Sliding Fiber Optic Patch Panel
The Opterna Fiber Optic 19” Sliding Patch Panel has been designed to facilitate internal fiber management and also to maximize fiber density in 1U, 2U heights.
The sliding tray provides easy access to fiber cabling, making this panel ideal for ‘Pay as you Grow’ applications. The mild steel construction and its black or grey powder coated finish makes this panel a high quality solution for any fiber optic installation, including Data Centers, FTTX and Telecommunications.
The panel supports 24 way and 48 way configurations in SC Simplex, SC Duplex, ST/FC (D cut out), LC Duplex (SC simplex foot print), LC Quad (SC Duplex foot print). Versions are available with MTP MPO cutouts on the back for use with pre-terminated MTP/MPO trunks.
Introduction
• Can be installed within standard 19” racks and wall mounted enclosures according to IEC 297-3 specification
• The universal design allows using both splice trays with one (central) and with two pins
• Rear of panel offers a range of apertures to accommodate a variety of gland configurations
• Optimum balance between panel depth and fiber management
• The base panel is designed for customized fiber management and splicing solutions
• Various anchoring points for incoming cables
• Front face of the panel includes a port identification strip
• Fiber management kits and splice cassette are offered as accessories
• All panels are available pre-loaded with adapters, pigtails and splice accessories
Features Sliding Fiber Optic Patch Panel
OSP Solutions
DASFPrev1 1/5
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
Sliding Fiber Optic Patch Panel
• Offers solution for optical splicing and patching
• Specifically designed for Data Center, communications room and telecommunication applications
OSP Solutions
Applications:
Drawing:
235.2
438.2 415.0
483.0
31.8
43.0
43.5
465.5
1
2 4
7
6
ITEM NO. PART NUMBER QTY.1 1SMP-538-1-LID-R3 12 1SMP-538-2-1U-BRACKET-R3 23 1SMP-538-10-INNER-ADAPTER-PLATE-24SC-R3 1
4 1SMP-538-9-SLIDING-TRAY-24SC-ASSY-R3 1
5 NYLATCH 2
6 Washer ISO 7089 - 4 4
7 ISO 7045 - M4 x 8 - Z --- 8N 4
DASFPrev1 2/5
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.comVisit: Opterna.com
Ordering info:
Ordering information for panel without MTP/MPO cutouts on the back
Part Number Item Description
FP-SL-SCDX-012-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way 12 SC Duplex cut out, Black color
FP-SL-SCSX-024-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way 24 SC Simplex cut out, Black color
FP-SL-SCDX-024-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 48 way 24 SC Duplex cut out, Black color
FP-SL-SCSX -048-2B Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way 48 SC Simplex cut out, Black color
FP-SL-DCSX-024-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24way 24 ST/FC Simplex D cut out, Black color
FP-SL-DCSX-048-2B Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 48 ST/FC Simplex D cut out, Black color
FP-SL-SCDX-012-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way,12 SC Duplex cut out, Gray color.
FP-SL-SCSX-024-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way, 24 SC Simplex cut out, Gray color
FP-SL-SCDX-024-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 48 way, 24 SC Duplex cut out, Gray color
FP-SL-SCSX-048-2G Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 48 SC Simplex cut out, Gray color
FP-SL-SCDX-024-2G Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 24 S C Duplex cut out, Gray color
FP-SL-DCSX-024-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way, 24 ST/FC Simplex D cut out, Gray color
FP-SL-DCSX-048-2G Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 48 ST/FC Simplex D cut out, Gray color
Sliding Fiber Optic Patch Panel
DASFPrev1 3/5
OSP Solutions
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
Ordering info:
Sliding Fiber Optic Patch PanelOSP Solutions
Ordering information for panel with MTP/MPO cutouts on the back
Part Number Item Description
FP-SL-SCDXM-012-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way 12 SC Duplex cut out, Black color
FP-SL-SCSXM-024-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way 24 SC Simplex cut out, Black color
FP-SL-SCDXM-024-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 48 way 24 SC Duplex cut out, Black color
FP-SL-SCSXM -048-2B Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way 48 SC Simplex cut out, Black color
FP-SL-DCSXM-024-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24way 24 ST/FC Simplex D cut out, Black color
FP-SL-DCSXM-048-2B Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 48 ST/FC Simplex D cut out, Black color
FP-SL-SCDXM-012-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way,12 SC Duplex cut out, Gray color
FP-SL-SCSXM-024-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way, 24 SC Simplex cut out, Gray color
FP-SL-SCDXM-024-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 48 way, 24 SC Duplex cut out, Gray color
FP-SL-SCSXM-048-2G Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 48 SC Simplex cut out, Gray color
FP-SL-SCDXM-024-2G Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 24 S C Duplex cut out, Gray color
FP-SL-DCSXM-024-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way, 24 ST/FC Simplex D cut out, Gray color
FP-SL-DCSXM-048-2G Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 48 ST/FC Simplex D cut out, Gray color
DASFPrev1 4/5
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
Visit: Opterna.com
Accessories:
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
OSP Solutions
Sliding Fiber Optic Patch Panel
Part Number Item Description
OPFC-STGR24 Universal Opterna Splice Tray for two splice holders, unloaded
OPFC-STGR24-L Cover for OP-FC-STGR-24
OPFC-STGR24-CH Holder for 12 metal crimp splice protectors
OPFC-STGR24-SH Holder for 6 heat shrink splice protectors
OPFC-STGR24-CH Stacking hinge for OPFC-STGR24
FP-AC-ST-12 12 way Stackable Splice Tray with Splice Holder and cover
FP-AC-ST-24 24 way Stackable Splice Tray with Splice Holder, Clear Cover
FP-AC-SB-24 24 way Splice Bridge with Adhesive Strip and Cover
FP-AC-CG-11B PG11 (4.5-10mm) Size Cable Gland & Back Nut, Black Nylon LSF material
FP-AC-BC Bunny Clip
FP-AC-FMK Fiber Management Kit consists of 1 x FP-AC-SB-24, 1 x FP-AC-CG-11 and 8 x FP-AC-B
FP-AC-BLNK-SCSX SC Simplex Blank cover
FP-AC-BLNK-SCDX SC Duplex Blank cover
FP-AC-BLNK-DCSX ST/FC Simplex Blank cover
PSCL-600-15-30 60mm Clear Fusion Splice Protector Sleeve
DASFPrev1 5/5
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
Telescopic Fiber Patch Panel
The telescopic fiber optic patch panel offers excellent flexibility during mounting and installation. Mainly used for distribution and splicing of feeder or distribution fiber cables. The patch panel features an improved staggered adaptor design for easy access to the connectors and patch cords during maintenance and fiber patching.
A sliding telescopic tray feature is incorporated to facilitate easy access for maintenance and also allows the tray to be released from the patch panel for maintenance. The telescopic patch panel is constructed of high quality steel that makes it study and durable. The panel is powder coated to ensure durability.
Introduction
• 1U, 2U, 3U, 4U design
• Telescopic tray can be fully ejected for easy splicing
• 300mm depth for extra storage
• High quality locking system
• Angled cable entries to maintain bend radius
• Strength member lug for securing the central strength member
• Splice tray for terminating incoming fibers to pigtails
• Staggered port design for easy patching
• Port identification on front panel
Features Telescopic Fiber Patch Panel
Central OfficeSolutions
DSFP3rev1 1/3
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
Telescopic Fiber Patch Panel
Applications:
Specifications:
Central OfficeSolutions
DSFP3rev1 2/3
• LAN/WAN
• FTTx
• Telecommunications
• CATV
Mounting Dimensions 19” according to IEC 297-3 specification
Cable Entry 1U PG 16, 2 Ports2U PG 16, 2 Ports3U PG 16, 2 Ports4U PG 21, 2 Ports
Panel Dimensions 1U – 43 mm(H) x 439 mm(W) x 311.5 mm(D)2U – 88 mm(H) x 439 mm(W) x 311.5 mm(D)3U – 132 mm(H) x 439 mm(W) x 311.5 mm(D)4U – 177 mm(H) x 439 mm(W) x 311.5 mm(D)
Adaptor SC Duplex, SC Simplex, ST/FC
Sliding Mechanism Telescopic Rails
Body Construction 1.2mm Steel Sheet
Powder Coated Paint RAL 7032
Americas:(703) 653-1130sales.us@opterna.com
Europe:+44(0)2031 301 716sales.eu@opterna.com
Middle East:+971 4 299 7676sales.me@opterna.com
Asia Pacific:+91(0) 484 2104 779sales.ap@opterna.com
OpternaROpternaR
Visit: Opterna.com
Visit: Opterna.com
Ordering Info:
Telescopic Fiber Patch PanelCentral Office
Solutions
DSFP3rev1 3/3
Part Number Item Description
FP-SLTR-SCSX-024-1G Telescopic 24 Way Fiber Patch Panel, 1U 24 SC Simplex cutout
FP-SLTR-SCDX-012-1G Telescopic 24 Way Fiber Patch Panel, 1U 12 SC Duplex cutout
FP-SLTR-DCSX-024-1G Telescopic 24 Way Fiber Patch Panel, 1U 24 ST/FC Simplex, D cutout
FP-SLTR-SCSX-048-2G Telescopic 48 Way Fiber Patch Panel, 2U 48 SC Simplex cutout
FP-SLTR-SCDX-024-2G Telescopic 48 Way Fiber Patch Panel, 2U 24 SC Duplex cutout
FP-SLTR-DCSX-048-2G Telescopic 48 Way Fiber Patch Panel, 2U 48 ST/FC Simplex, D cutout
FP-SLTR-SCSX-072-3G Telescopic 72 Way Fiber Patch Panel, 3U 72 SC Simplex cutout
FP-SLTR-SCDX-036-3G Telescopic 72 Way Fiber Patch Panel, 3U 36 SC Duplex cutout
FP-SLTR-DCSX-072-3G Telescopic 72 Way Fiber Patch Panel, 3U 72 ST/FC Simplex cutout
FP-SLTR-SCSX-096-4G Telescopic 96 Way Fiber Patch Panel, 4U 96 SC Simplex cutout
FP-SLTR-SCDX-048-4G Telescopic 96 Way Fiber Patch Panel, 4U 48 SC Duplex cutout
FP-SLTR-DCSX-096-4G Telescopic 96 Way Fiber Patch Panel, 4U 96 ST/FC Simplex cutout
Related Accessories:
SP-TR-1224-BK 12 way stackable splice tray with splice holder and Cover, 180 mm (L) x 113 mm(L) x 13 mm (H)
SP-TR-1224-WH 24 way stackable splice tray with splice holder and Cover, 225 mm (L) x108 mm(W) x 13 mm (H)
SP-TR-1224-BL 24 way stackable splice tray with splice holder and Cover, 160 mm (L) x 105 mm(W) x 10 mm (H)
FP-AC-SB-24 24 way Splice Bridge with Adhesive Strip and Cover
FP-AC-CG-11B PG11 (4.5-10mm) Size Cable Gland & Back Nut, Nylon, Black
FP-AC-CG-16B PG16 (4.5-10mm) Size Cable Gland & Back Nut, Nylon, Black
FP-AC-BC Bunny Clip
FP-AC-FMK Fiber Management Kit consists of 1 x FP-AC-CG-16 and 8 x FP-AC-BC
FP-AC-BLNK-SCSX SC Simplex Blank Cover
FP-AC-BLNK-SCDX SC Duplex Blank Cover
FP-AC-BLNK-DCSX ST/FC Simplex Blank Cover
Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.
top related