building construction v
TRANSCRIPT
-
7/30/2019 Building Construction V
1/18
11/21/12
Click to edit Master subtitle style
BUILDING CONSTRUCTION V
-PERCUSSION BORING-
PRESENTED BY:Mohd Al Fitri (Miri Sarawak)Jalaluddin (Papar Sabah)
Hafyqri (Rampangi Kuching)Mohd Hosni (Rampangi Kuching)Nurul Hanie (Banting Selangor)
PRESENTED FOR:SIR MUZANI (Lect Building)
-
7/30/2019 Building Construction V
2/18
11/21/12
introduction...
Soil investigation is process ofinspection to determine the soilcondition.
Soil investigation can be divided intofive (5) methods of investigation :
a) Percussion boringb) Deep sounding
c) Seismic
d) Electrical resistivity
-
7/30/2019 Building Construction V
3/18
11/21/12
Percussion Boring...
CABLE TOOL
BORING
-
7/30/2019 Building Construction V
4/18
11/21/12
Introduction...
According to R. Whitlow, percussionboring is also known as shell augermethod
It is also known as Standard Method
and Light Cable Tool Method.
This method is used to make hole in
all types of soils including boulders
-
7/30/2019 Building Construction V
5/18
11/21/12
The used bits are the bailer and theclay cutter is an open in cohesion
less soils, is a steel tube with a clackvalve at the tip, the clay cutter is anopen steel tube with a cutting shoe.
Depth of up to 60 m can be reached,with borehole diameters rangingfrom 150 to 300mm.
-
7/30/2019 Building Construction V
6/18
11/21/12
Most usual borehole 150mm, butothers up to 300mm can be drilled;the maximum depth of exploration,although dependent on soil type tosome extent, is around 50-60m.
The advantage of this method is its
simplicity, but it is difficult to identifythin soil layers or macrofabricfeatures.
-
7/30/2019 Building Construction V
7/1811/21/12
Equipments...
Consists of derrick,
power-winch,
A set of drilling tools.
-
7/30/2019 Building Construction V
8/1811/21/12
TRADITIONAL METHOD
-
7/30/2019 Building Construction V
9/1811/21/12
TYPE OF PERCUSSION
VIBRATION /HAMMERING
Sand Shell/BailerDRILLINGRotary Auger
DRILLING AND VIBRATION
Shell Auger
-
7/30/2019 Building Construction V
10/1811/21/12
Sand Shell Bailer
-
7/30/2019 Building Construction V
11/18
11/21/12
Rotary Drilling
-
7/30/2019 Building Construction V
12/18
11/21/12
Is the oldest method of making aborehole
Particularly - penetrating coarsegravels, boulders and hard strata.
Heavy drilling bit is raised and
dropped by means of a cable.
-
7/30/2019 Building Construction V
13/18
11/21/12
Methods...
Tool assembly is raised by the winchto about 1m above the bottom of thehole,
and then it is allowed to fall underits weight, thus driving the cuttingtool into the soil
A small amount of water is kept in
-
7/30/2019 Building Construction V
14/18
11/21/12
Taking soil sample from the shellauger
Cable used to raised the tools and dropped with its ownweight.
-
7/30/2019 Building Construction V
15/18
11/21/12
-
7/30/2019 Building Construction V
16/18
11/21/12
Methods...
Bailing is repeated until the hole hasbeen adequately cleaned, at whichtime drilling is resumed; drilling andbailing are then alternated.
If the hole is unstable, casing islowered and the driving of casing is
alternated with the other twoprocesses.
In loose granular material, such as
sand, bailing alone may be sufficient
-
7/30/2019 Building Construction V
17/18
11/21/12
Methods...
Water should be added at the time ofboring and the debris bailed out atinterval. The bit may be suspendedby a cable or rods from walking
beam.
Where the boring is in soil or intosoft rocks and provided that asampler can be driven into them.Cores may be obtained at the
intervals using suitable tools.
-
7/30/2019 Building Construction V
18/18
11/21/12
The percussion method is versatile,allowing all types of materials to bepenetrated.
However, in very hard stone,progress is slow. While this method isfrequently associated with large,
motorized, truck-mountedequipment, it can be successfullyscaled down and used withmanpower, or small engines.