Download - JPX162II
-
7/27/2019 JPX162II
1/21
Telecom Components
JPX162 II Terminal Block
DESCRIPTION
JPX162 II is a Terminal BlockDesigned for MDF, on the
subscriber Side of the main frame.
It allows 100 pair connections of
twisted pairs coming from the
subscriber.
Blocks with strips of 10 pairs.
-
7/27/2019 JPX162II
2/21
Telecom Components
Double Insulation Displacement Contact (IDC)
Label holders per block to facilitate the identification of
each pair.
Individual overcurrent and overvoltage protection of each
pair.
Differenct modules for continuity of each pair
-
7/27/2019 JPX162II
3/21
Telecom Components
Characteristics
-
7/27/2019 JPX162II
4/21
Telecom Components
JPX162II100 pair Terminal Block Dimension
Protection Plug Dimension
-
7/27/2019 JPX162II
5/21
Telecom Components
ACCESSORIES
Protection Module :
Continuity and Overvoltage +
OverCurrent protection (PTC)
Continutiy Module :
Ensure the link between
cable and jumpers
-
7/27/2019 JPX162II
6/21
Telecom Components
-
7/27/2019 JPX162II
7/21
Telecom Components
Protection plug installation:
Hold on to the Protection plug handle.
Than insert into the rectangle hole of the front
of the 100 pair MDF block.
Pay attention, do not revering the protection plug.
The dark face of protection plug should be face up.
-
7/27/2019 JPX162II
8/21
Telecom Components
ACCESSORIES
OSA2 TERMINATION TOOL
Used to connect terminalcable, jumper cable,
clip/cancel wire.
Life span more than100000 times
-
7/27/2019 JPX162II
9/21
Telecom Components
-
7/27/2019 JPX162II
10/21
Telecom Components
-
7/27/2019 JPX162II
11/21
Telecom Components
-
7/27/2019 JPX162II
12/21
Telecom Components
-
7/27/2019 JPX162II
13/21
Telecom Components
-
7/27/2019 JPX162II
14/21
Telecom Components
Test Cord/Patch Cord
To get electrical signals of
Inside/outside wire throughTest cord.
Equipped with two groupsSpring strip, the contact
Perform test in order to
Find fault.
-
7/27/2019 JPX162II
15/21
Telecom Components
INSTALLATION
100 pair Cable Installation on the left side
-
7/27/2019 JPX162II
16/21
Telecom Components
100 pair cable install on the left side of the terminal block.
According to the proper order of the cable core number, 10
pair/group will be inserted into the rectangle hole of the
plastic pass wire ring .
Each pair cable will be inserted into the
corresponding pass wire guide hole, pass through wire
guide slot, lead each wire to single IDC strip, then connecteach pair in connecting slot of IDC by a termination Tool,
the remaining wire will be cut automatically.
-
7/27/2019 JPX162II
17/21
Telecom Components
Jumper connection
On the right side
-
7/27/2019 JPX162II
18/21
Telecom Components
A pair of jumper will be inserted into the rectangle
Hole of the plastic pass wire ring, pass through the
Side wire guide slot.
Finally get to connection place of IDC spring strip.
Then connect each pair in connecting slot of IDC by
a termination Tool, the remaining wire will be cut
automatically.
-
7/27/2019 JPX162II
19/21
Telecom Components
Back View Front View
-
7/27/2019 JPX162II
20/21
Telecom Components
Alarm System
-
7/27/2019 JPX162II
21/21
Telecom Components
Used together with alarm
signal disk and vertical signal
light.
When protection plug works, it
send alarm signal and at thesame time LED of
The protection plug & 100 pair
block light up
When there is a loose contact
on the Cable side IDC, LED will
light up also.