install guide sinocolor sj740/740i

7/24/2019 Install Guide Sinocolor SJ740/740i

1/19

Read this first.This describes the setup tasks and important conditions aboutthe installation location that must be met in order to enable useof this machine.

SJ-740/ SJ-740i

InstallGuide


2/19

CATALOGUE

Installation Requirement ........................................................................................... 1

Included Items .............................................................................................................. 2

1. Assemble Mechanical Part ................................................................................... 4

1.1 : Assemble the Stand - Mount the Machine . .............................................................. 4

1.2 : Install the Media Feeder and Media Take Up (if any) ............................................. 4

1.3 : Install Cooling Fan ............................................................................................................... 5

1.4 : Install Drain Bottle............................................................................................................... 5

1.5 : Install Upper Part of the Printer ..................................................................................... 61.6 : Remove Packing Material ................................................................................................. 6

1.7 : Parts Name ............................................................................................................................. 6

2. Turn On the Printer for the First Time Check ................................................. 9

3. Install Media .............................................................................................................. 9

4. Install Printhead and Related Part ................................................................... 11

4.1 : Install Printhead ................................................................................................................ 11

4.2 : Fill Ink Cartridges .............................................................................................................. 13

4.3 : Install Damper and Fixator ............................................................................................ 13

5. Install USB Driver and PrintConsole ................................................................ 14

6. Fill Ink ......................................................................................................................... 16


3/19

Page 1

Installation Requirement

Install in a quiet, stable location offering good operating conditions. An unsuitable location cancause accident, fire, faulty operation, or breakdown.

Install the machine in a location that is level, stable, and able to bear the weight of themachine.The total weight of the machine may reach 400kg or more. Installation in an unsuitable locationmay cause a major accident, including tip over, fall, or collapse.

Install in a clean, brightly lit location.Conduct operations in a clean, brightly lit location. Working in a location that is dark or clutteredmay lead to an accident, such as becoming caught in the machine as the result of an inadvertentstumble.

Position so that the power plug is within immediate reach at all times.This is to enable quick disconnection of the power plug in the event of an emergency. Install the

machine next to an electrical outlet. Also, provide enough empty space to allow immediateaccess to the electrical outlet.

Ensure adequate ventilation for the work area.Failing to perform ventilation may result in a health hazard or danger of combustion due to inkfumes.

Temperature and HumidityKeep the room temperature between 20-30C, hundity 40-60%. Air conditioner and humidifiermay be required. Keep a distance from strong radiation field. The floor must be level.Maintain the specified temperature and humidity even when the machine is not in use. If

temperatures are too high or too low, it may cause malfunction.Electrical requirementElectrical requirement writes on a metal tag on the back of the printer. Find it to confirm if yourprinter supports 220V or 110V. A transformer is needed if your country standard is different.The printer must be well grounded.UPS and voltage stabilizer is highly recommended.

Computer requirementBasic requirement:CPU: 2.5 GHz or higher

Memory: 2GB or higherHard Disk: 200GB or higherOperating system: Microsoft Windows XP / Windows 7 Ultimate Edition / Windows 10

Recommendatory requirement:CPU: 3.5 GHz or higherMemory: 4GB or higherHard Disk: 500GB or higher (NTFS format)Operating system: Microsoft Windows 7 Ultimate Edition

NOTICE: Suggest user format your hard disk into 2 partitions (NTFS). The first partition is used

for installing OS and other software, the second partition is used to save pictures and work files.


4/19

Page 2

Included Items

The following items are packed together with the unit. Make sure they are all present andaccounted for.

No. Item Name RemarkQuantit

y Units

1 EPSON DX5 / DX7 Printhead 1 or 2 pc

2 UltraPrint / PhotoPrint Software UltraPrint does not include a CD 1 pc

3 USB Disk & USB DongleUSB Disk contains driver & manual,

Dongle is for PrintConsole & UltraPrint

4 USB Cable 1 pc

5 Spanner (hexagonal shaped) 1 set

6 Screw driver (cross shaped) 5x150 1 pc

7 Power Cable 0.75mm 1 pc1mm 11mmOutside heater * 1

8 ScrewM3x8 20 pc

M4x12 8 pcM6x16 26 pc

9 Damper 1 or 2 pc

10 Funnel fill ink 4 pc

11 Ink hard tube 370cm or 510cm 1 pc

12 Ink soft tube 100cm 1 pc

13 Syringe glass one for cleaningplastics one for manually pump

3 pc

14 ink pipe connector & Seal ring Connect ink tube and damper 4 pc

15 Media Holder 4-6x25 black screws 2 pc

16 Printhead Flat cable 6 pc

17 Drain Bottle 1 pc

18 Fuse10A 5 pc3A 10 pc

19 Capping Unit 1 or 2 pc

20 Wiper 1 or 2 pc

21 Fan holder screw 5x30black screws 4

22 Media Reflector * 1 pc

23 Heating holder screw * 5x30 4 pc

* Note : Items in red are optional parts


5/19

Page 3

Included Items


6/19

Page 4

1. Assemble Mechanical Part

1.1 : Assemble the Stand - Mount the Machine

1.2 : Install the Media Feeder and Media Take Up

* You may need to install the media reflector and make it faces towards the detector on stand 1.* In some models, media reflector is replaced with a installed infrared detector.* Media take up is optional part.


7/19

Page 5

1.3 : Install Cooling Fan

1.4 : Install Drain Bottle

* Be sure to insert the drain pipes into the drain bottle afterward.


8/19

Page 6

1.5 : Install Upper Part of the Printer

Lift the upper part with forklift or 4 men, and fix it onto the stands.* Be sure to insert the jointing rubber into the hole on top of the stands.

1.6 : Remove Packing Material

Remove the fixation rubber located on the left side of the carriage. Its used to fix the carriageduring shipping.

Remove the packing bags of the dampers.


9/19

Page 7

1.7 : Parts Name

Carriage Control PanelPinch Roller Emergency Switch

Cooling Fan Switch

Media Handle

Take Up Switch

Vacuum Switch

Main Power Switch

Cartridges

USB Port


10/19

Page 8

Carriage Board

Printhead Cable

Damper

Printhead

Wiper Capping Station Capping Unit Front & Back Heater


11/19

Page 9

2. Turn On the Printer for the First Time Check

After the stand assembling is completed, plug the power cables and turn on the printer.

Remember to turn on both main power switch and the emergency switch.

Normal start up action should be : The carriage moves out then goes back to home position, inthe mean time, the capping station goes down then goes up slightly leaving the printhead

uncapped.

This startup check can reduce the risk of a possible short circuit before installing the printhead.

Turn off the printer afterward.

3. Install Media

Step 1 : Install the media holder and fit on the media tube.

Step 2 : Pass the leading edge of the media through the pinch rollers and pull out the media

over the platen.

(Be sure the media is put straight and taut.)

Step 3 : Lower the loading level, then secure the media holder by tightening the securing

screws slightly.(Be sure both edges of the media are not covered by the pinch rollers.)

Step 4 : Move the media clamps onto both edges of the media.

(Be sure only around 5mm of each edge is covered by the media clamp.)

Step 5 : Hang down the paper to block the media sensor and reflector.

(This can be done manually, or turn on the media feeding motor to rotate the paper tube

forward.)

Heavy Roll : Simply put the media tube onto both media rollers, also need to hang down the

paper to block the media sensor and reflector. Its better to put an empty hard paper tube to

make paper feeding smooth.


12/19

Page 10

Step 1

Step 3

Step 2

Step 4

Step 5 Heavy Roll


13/19

Page 11

4. Install Printhead and Related Part

4.1 : Install Printhead

Step 1 : Connect flat cables onto the printhead.

* Be sure the power is off.

* Be sure the text sides of cables are put back to back. (outwards)

* Be sure your hand is dry, no ink / liquid gets onto the cables.

* Be sure the contact pins are well touched and not bent.


14/19

Page 12

(The other side of cables are already connected)

Step 2 : Fix the printhead onto the carriage plate by fasten 3 screws.


15/19

Page 13

4.2 : Fill Ink Cartridges

Use funnel to fill ink into cartridges. Remember to seal them afterwards.

4.3 : Install Damper and Fixator

Fix the damper onto the printhead, with gentle strength.

* the printhead connector for damper is actually fragile, not as strong as it looks.

* Color arrangement should be :C M C M

K K Y Y

Damper

Fixator


16/19

Page 14

5. Install USB Driver and PrintConsole

USB Driver and PrintConsole install program can be found in the USB flash drive.

Install the USB driver according to your operation system (32bit / 64bit).

Install the PrintConsole according to your printer model. Then launch the PrintConsole and select

the configuration file.

: SJ-740, SJ-1260, ES-740

Note : If you use single head on a two head model, you should still select the PrintConsole for Dual

Head Model, but select a different configuration file.

: SJ-740i, SJ-640i, ES-740i

: UV-740, UV-1260

ES-740 with one head

ES-740 with two heads

SJ-740 / SJ-1260 with one head

SJ-740 / SJ-1260 with two head

ES-740i

SJ-640i

SJ-740i

UV-740 / UV-1260 with one head

UV-740 / UV-1260 of CMYK

UV-740 / UV-1260 of CMYK with White


17/19

Page 15

Connect the green USB Dongle. It is required for both PrintConsole and UltraPrint.

Turn on the printer and restart PrintConsole, left bottom corner turns green and says

Printer Connected. Now the printer is ready to serve.


18/19

Page 16

6. Fill Ink

Click Settings, select Heads for two heads, select Head1 for single head, then click Fill Ink button.


19/19

Thank you for choosing SinoColor products.

Contact UsSales Email : [email protected] Email: [email protected] : www.sanyi-tech.com

install guide sinocolor sj740/740i

Documents