installation aii 12085 cr-v instructions starter … · remote control engine starter unit kit. p/n...

Publications No.

INSTALLATIONINSTRUCTIONS

Accessory Application

2011 American Honda Motor Co., Inc. All Rights Re

AII 12085

REMOTE CONTROL ENGINE

STARTER

served. AII 46215 (1112

CR-V

) 0

Issue Date

DEC 2011

PARTS LIST

Remote Control Engine Starter Unit KitP/N 08E91-E22-101A

Transmitter

Control unit

Antenna

Key ring

Protective tape

Fuse label

Caution label

Accessory Users Information Manual

Quick Start Guide

Remote Control Engine Starter Attachment KitP/N 08E92-T0A-100A

Control unit bracket

Engine starter harness

3 Relays

8 mm Nut

20 Wire ties

1 of 278E92-T0A-1A00-90

Long wire tie

7 Urethane tapes

Template

Clip

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Diagonal cutters

Ratchet

8 mm, 10 mm, and 12 mm Sockets

Combination wrench

Isopropyl alcohol

Scissors

Small flat-tip screwdriver

Shop towel

Ruler

Tape measure

HDS (Honda Diagnostic System)

Needle nose pliers

Masking tape

Electrical tape

The following tool is available through the Honda Tool and Equipment Program. On the iN click on: Service > Service Bay > Tool and Equipment Program, the enter the number under search. Or call 888-424-6857.

Trim Tool Set (T/N SOJATP2014)

2 of 27 AII 46215

Illustration of the Remote Control Engine Starter Installed on the Vehicle

INSTALLATION

NOTE: This antenna should only be installed if the ambient air temperature 15C (60F) or above.

1. Move the drivers seat all the way back.

2. Disconnect the negative cable from the battery.

Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers.

Q0N2312AG

40A FUSE

CONTROL UNITANTENNA

3 RELAYS

3A FUSEENGINE STARTER HARNESS

(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.

Setting the Control Unit

3. Using a small flat-tip screwdriver, set the switches on the (accessory) control unit to the locations shown.

NOTE:

The switches must be set before the control unit is plugged in.

If the switch settings are not correct, the remote engine starter will not operate correctly.

If setting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.

If you change the switch settings with the unit connected, you must disconnect the unit, then reconnect it before the new settings are recognized.

921301AD

CONTROL UNITSMALL FLAT-TIP

SCREWDRIVER

Discharge any static electricity.

SET

SWITCHES

SWITCHES

SW:1 RR Junction unit --------------------> OFF

SW:2 Trunk or Tailgate --------------------> ON

SW:3 Smart Entry----------------------------> OFF

SW:4 Horn or Buzzer Answerback-----> OFF

SW:5 Trunk Main SW -----------------------> OFF

SW:6 Reserve ---------------------------------> OFF

2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215

4. Using isopropyl alcohol on a shop towel, clean the control unit where the protective tape will attach. Remove the adhesive backing, and attach the protective tape to the control unit over the switches.

Removing the Vehicle Parts

5. Remove the roof console.

Using a plastic trim tool, pry out and remove the left and right lens (four retaining tabs each).

Open the sunglass holder and remove the four screws.

Remove the roof console (unplug the vehicle connectors).

772505AS

CONTROL UNIT

SWITCHESPROTECTIVE TAPE

ADHESIVE BACKINGRemove.

Clean with isopropyl alcohol.

Q0N2012AG

VEHICLE CONNECTORS

ROOF CONSOLE

4 SCREWS

4 RETAINING TABS

LEFT LENS

SUNGLASS HOLDEROpen.

4 RETAINING TABS

RIGHT LENS

(1112) 3 of 27

6. Release the drivers sunvisor and passengers sunvisor from the two sunvisor holders.

7. Rotate each sunvisor holders 45 counterclockwise to remove the two sunvisor holders.

8. Pull away the drivers door opening seal from the drivers A-pillar. Gently pull out the drivers A-pillar trim to release the clips.

Q0N2013AG

Rotate.

SUNVISOR HOLDER

SUNVISOR HOLDER

2 SUNVISOR HOLDERS

SUNVISOR

Q0N2014AG

VEHICLE PANEL

CLIP

2 CLIPS

DRIVERS A-PILLAR TRIM

DRIVERS DOOR OPENING SEALPull away.

CLIP

DRIVERS A-PILLAR

4 of 27 AII 46215

9. To prevent the clips from falling into the vehicle body, roll up the shop towel, and insert it between the drivers A-pillar and the dashboard. Take care not to damage the drivers A-pillar.

10. Remove the drivers A-pillar trim. Carefully remove the shop towel and any clips that fell from the drivers A-pillar trim. NOTE: The upper clip will stay in the body.

Q0N2015BG

SHOP TOWEL

DRIVERS A-PILLAR

DASHBOARD

Q0N2016AG

UPPER CLIPDRIVERS A-PILLAR TRIMRemove.

DRIVERS A-PILLAR TRIM


11. Remove the remaining upper clip from the drivers A-pillar.

12. Temporarily reinstall the drivers A-pillar trim, and check the overlap between the headliner and the drivers A-pillar trim according to the service manual. Remove the drivers A-pillar trim. Install the new clip (supplied) to the drivers A-pillar trim.

Q0N2017AG

Push 2 tabs.UPPER CLIPDiscard.

DRIVERS A-PILLAR

Q0N2018AG

DRIVERS A-PILLAR TRIM(inside)

NEW CLIP


13. Remove the drivers dashboard panel (six clips and unplug the vehicle connector).

14. Remove the drivers air outlet (one self-tapping screw, one retaining tab, and three clips).

Q0N2019BG

VEHICLE CONNECTOR

6 CLIPS

DRIVERS DASHBOARD PANEL

Q0N2020BG

DRIVERS AIR OUTLET

2 CLIPS

RETAINING TAB

SELF-TAPPING SCREW

CLIP

(1112) 5 of 27

15. Remove the drivers dashboard under cover (turn the knob, one clip and one pin).

16. Remove the drivers dashboard lower cover (eight clips and unplug the vehicle connector).

Q0N2021BGPINDRIVERS DASHBOARD UNDER COVER

KNOBTurn.

CLIP

Q0N2022AG

VEHICLE CONNECTOR

8 CLIPSDRIVERS DASHBOARD LOWER COVER

6 of 27 AII 46215

17. Attach masking tape to the upper column cover as shown.

18. Lower the tilt lever, and turn the steering wheel 90 counterclockwise.

19. Using a plastic trim tool, release the lock as shown.

Q0N2023AG

MASKING TAPE

UPPER COLUMN COVER

STEERING WHEEL

Q0N2024BG

PLASTIC TRIM TOOL

STEERING WHEEL

LOCK

UPPER COLUMN COVER


20. Turn the steering wheel 180 clockwise. Using a plastic trim tool, release the lock as shown.

21. Secure the upper column cover to the meter panel with the tape.

Q0N2025BG

LOCK

UPPER COLUMN COVER

PLASTIC TRIM TOOL

Q0N2026AG

TAPE

2 RETAINING TABS

UPPER COLUMN COVER

METER PANEL


22. Remove the two self-tapping screws from the lower column cover.

23. Remove the lower column cover (one self-tapping screw).

Q0N2027AG

LOWER COLUMN COVER

SELF-TAPPING SCREWS

Q0N2028AG

SELF-TAP-PING SCREW

LOWER COLUMN COVER

(1112) 7 of 27

24. Remove the drivers front door sill trim (two retaining tabs, three clips and two hooks).

25. Pull away the drivers door opening seal, and remove the drivers kick panel (two clips).

Q0N2029BG

2 RETAINING TABS

FRONT

3 CLIPS

2 HOOKS

DRIVERS FRONT DOOR SILL TRIM

Q0N2030AG

DRIVERS DOOR OPENING SEALPull away.

DRIVERS KICK PANEL

2 CLIPS

8 of 27 AII 46215

Installing the Antenna

26. Using the two pairs of needle nose pliers, bend the antenna plate according to the full scale drawing as shown.

Q0N1708CG

ANTENNA

ANTENNA

ANTENNA PLATE

NEEDLE NOSE PLIERS

ANTENNA PLATE

SCALE

9 mm(0.3 in.)

15 mm(0.6 in.)


27. Using scissors, cut out the template.

28. Using the strips of masking tape, attach the template to the front windshield. Align the template with the black ceramic paint as shown.

Q0N1701BG

Cut out.

TEMPLATE

SCISSORS

Q0N1702CG

TEMPLATE

MASKING TAPES

Align this end with the end of the black ceramic paint.

TEMPLATE

BLACK CERAMIC PAINT

FRONT WINDSHIELD

CORRECT


29. Starting from the antenna end of the antenna cable, wrap three urethane tapes to the antenna cable at the measurements shown.

30. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the antenna will attach.

31. Remove the adhesive backing from the antenna. Insert the antenna plate under the headliner, align the antenna with the template, and attach the antenna to the front windshield. Press the antenna firmly for 30 seconds.

32. Remove the template.

Q0N1703AG

ANTENNA

URETHANE TAPES

20 mm(0.8 in.)

410 mm(16.1 in.)

ANTENNA CABLE

ANTENNA CABLE

20 mm(0.8 in.)

Q0N1704AG

ANTENNA PLATE


ANTENNA

TEMPLATE

FRONT WINDSHIELDClean with isopropyl alcohol.

HEADLINER

(1112) 9 of 27

33. Gently pull down the headliner, and tuck the antenna cable under the headliner. Be careful not to crease the headliner.

34. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle panel, where the urethane tapes will attach.

35. Using scissors, cut one urethane tape in half. Secure the antenna cable to the vehicle panel with two cut pieces of urethane tape. Be careful not to crease the headliner.

Q0N1705AG

ANTENNA CABLE

HEADLINER

HEADLINERVEHICLE PANEL

ANTENNA CABLE

Q0N1706AG

VEHICLE PANELClean with isopropyl alcohol.

ANTENNA CABLE

2 URETHANE TAPES

URETHANE TAPECut in half.

10 of 27 AII 46215

36. Route the antenna cable down the drivers A-pillar along the vehicle harness.

37. Secure the antenna cable to the vehicle harness with six wire ties.

38. Route the antenna cable down behind the dashboard.

Q0N1707AG

ANTENNA CABLE

6 WIRE TIES

DRIVERS A-PILLAR

VEHICLE HARNESS

Q0N1709BG

ANTENNA CABLE

TOP VIEW

FRONTSTEERING HANGER BEAM


Routing the Engine Starter Harness

39. Plug the three relays into the relay block on the engine starter harness.

40. Using isopropyl alcohol on a shop towel, thoroughly clean the relay block and fuse block where the 3A fuse label and 40A fuse labels will attach.

41. Attach the 3A fuse label and two 40A fuse labels to the relay block and fuse block on the engine starter harness.

42. Route the two 28-pin connectors of the engine starter harness upward as shown.

Q0N1801AG

40A FUSE LABEL

RELAYS

RELAY

40A FUSE LABEL

FUSE BLOCK

RELAY BLOCK

ENGINE STARTER HARNESS

3A FUSE LABEL

Q0N1802BGENGINE STARTER HARNESS

STEERING HANGER BEAM

ENGINE STARTER HARNESS 28-PIN CONNECTOR


43. Unplug the vehicle 28-pin connector.

44. Route the engine starter harness 28-pin connectors as shown, and plug the engine starter harness 28-pin connector into the vehicle 28-pin connector.

45. Push the engine starter harness 28-pin connector between the drivers A-pillar and vehicle 28-pin connector as shown.

46. Plug the vehicle 28-pin connector into the engine starter harness 28-pin connector.

Q0N1804CG

VEHICLE 28-PIN CONNECTOR


Q0N1805BG



TOP VIEW

FRONT


DRIVERS A-PILLAR


(1112) 11 of 27

47. Secure the engine starter harness and the antenna cable to the vehicle frame with one wire tie.

48. Secure the engine starter harness and the antenna cable to the vehicle harness with one wire tie.

Q0N1806BG

VEHICLE HARNESS

WIRE TIE


WIRE TIE


VEHICLE FRAME

ANTENNA CABLE

ANTENNA CABLE

12 of 27 AII 46215

49. Unplug the vehicle 5-pin connector from the fuse box, and plug it into the engine starter harness 5-pin connector.

50. Plug the remaining engine starter harness 5-pin connector into the fuse box. NOTE: Check that the engine starter harness 5-pin connector is securely connected to the fuse box 5-pin connector. A loose connection can cause the engine to stall.

Q0N1807BG

FRONT VIEW



FUSE BOX

FUSE BOX

Plug in here.

UNLOCK LOCK13

12 2Push.Push.Pull.


51. Attach the connector clip from the engine starter harness 5-pin connector to the hole in the vehicle panel.

52. Slide the other clip on the engine starter harness onto the vehicle connector. Note the direction and the orientation of the clip.

Q0N1901BG


FUSE BOX

VEHICLE PANEL

HOLE

CONNECTOR CLIP

Q0N1902BG


CLIP

VEHICLE CONNECTOR

FRONT


If the vehicle is equipped with the accessory fog lights, go to step 54; otherwise, continue with step 53.

53. Plug the engine starter harness 4-pin connector into the fuse box. Go to step 56.

Q0N1903BG

FRONT VIEW

FUSE BOX

FUSE BOX

Plug in here.


(1112) 13 of 27

54. Unplug the fog light 4-pin connector from the fuse box, and plug it into the engine starter harness 4-pin connector.

55. Plug the remaining engine starter harness 4-pin connector into the fuse box.

Q0N1904BG

FRONT VIEW

FUSE BOX

FUSE BOX

Plug in here.


FOG LIGHTS 4-PIN CONNECTOR


14 of 27 AII 46215

56. Unplug the vehicle 38-pin connector from the fuse box as shown.

57. Remove the connector cover.

58. Remove the lever from the vehicle 38-pin connector as shown.

Q0N1905AG


FUSE BOX

FRONT VIEW


CONNECTOR COVER

QA21701AG


LEVERRemove.

VEHICLE

38-PIN CONNECTOR

2 TABS

8-PIN CONNECTOR

HARNESS SIDE VIEW

8-PIN CONNECTOR


59. Remove the 8-pin connector from the vehicle 38-pin connector (two tabs).

60. Release the retainer from the 8-pin connector.

61. Insert the engine starter harness terminal (orange wire) into the 8-pin connector. Reinstall the 8-pin connector and lever.

62. Secure the engine starter harness to the vehicle harness with an electrical tape.

Q0D1604AK

HARNESS SIDE VIEW

ORANGE WIRE

ENGINE STARTER HARNESS TERMINAL

RETAINER

8-PIN CONNECTOR

ORANGE WIRE

Q0N1907AG

VEHICLE HARNESS


ELECTRICAL TAPE


63. Reinstall the connector cover.

64. Plug the vehicle 38-pin connector into the fuse box.

65. Unplug the vehicle 24-pin connector, and plug the engine starter harness 24-pin connector into the vehicle 24-pin connector.

FRONT VIEW

FUSE BOX

FUSE BOX




(1112) 15 of 27

66. Slide the clip from the engine starter harness 24-pin connector onto the bottom of the fuse box, then plug the remaining vehicle 24-pin connector into the engine starter harness 24-pin connector.

Q0N2002BG

FRONT VIEW

FUSE BOX

FUSE BOX



FUSE BOX


16 of 27 AII 46215

67. Secure the engine starter harness to the vehicle harness with two wire ties.

68. Route the engine starter harness under the dashboard and toward the steering wheel.

69. Secure the engine starter harness to the hole in the left knee bolster using the clip on the engine starter harness as shown.

Q0N2003BG

FUSE BOX


VEHICLE HARNESS

WIRE TIES

Q0N2004AG


FRONT

LEFT KNEE BOLSTER

HOLE

CLIPFRONT



HARNESS

70. Locate the white tape on the engine starter harness, and loosely secure the engine starter harness to the dashboard with one wire tie at the white tape.

71. Route the engine starter harness up steering wheel as shown.

72. Align the white tape on the engine starter harness with the vehicle clip, and secure the engine starter harness to the vehicle harness with two wire ties as shown.

Q0N2005AG


WIRE TIELoosely secure.

DASHBOARD

WHITE TAPE

Q0N2006BG

ENGINE STARTER HARNESSVEHICLE

CLIP

WHITE TAPE

FRONT

VIEWED FROM BOTTOM

2 WIRE TIES

VEHICLE HARNESS


73. Unplug the vehicle 7-pin connector from the ignition switch, and plug it into the engine starter harness 7-pin connector (black).

74. Plug the remaining engine starter harness 7-pin connector (black) into the ignition switch.

75. Secure the 7-pin connectors and engine starter harness to the vehicle harness with one wire tie.

Q0N2007AG


ENGINE STARTER HARNESS 7-PIN CONNECTOR (Black)

ENGINE STARTER HARNESS 7-PIN CONNECTOR (Black)

IGNITION SWITCH

STEERING WHEEL

Q090211BK

VEHICLE HARNESS

7-PIN CONNECTORS

WIRE TIE ENGINE

STARTER

(1112) 17 of 27

76. Route the engine starter harness across the steering column area as shown.

77. Unplug the vehicle 10-pin connector from the wiper switch, and plug it into the engine starter harness

10-pin connector.

78. Plug the remaining engine starter harness 10-pin

Q0N2008AG




STEERING WHEEL

WIPER SWITCH


18 of 27 AII 46215

connector into the wiper switch.

79. Secure the 10-pin connectors and engine starter harness to the vehicle harness with one wire tie.

Q090302BK

IGNITION SWITCH

WIRE TIE

10-PIN CONNECTORS


STEERING WHEEL


80. Unplug the vehicle 12-pin connector from the combination light switch, and plug it into the engine starter harness 12-pin connector.

QA20704BG



STEERING WHEEL

COMBINATION LIGHT SWITCH



81. Plug the remaining engine starter harness 12-pin connector into the combination light switch.

82. Secure the engine starter harness to the vehicle harness with two wire ties. Check that the harness is secured without undue strain to the both left and right connector cords. NOTE: Make sure that the connectors and harness are not pinched, or interfering with the steering wheel when adjusted.

Q0N2010BG


VEHICLE HARNESS

WIRE TIES

LEFT CONNECTOR CORD(without undue strain)

RIGHT CONNECTOR CORD(without undue strain)

(1112) 19 of 27

83. Route the antenna cable along the engine starter harness as shown.

84. Secure the antenna cable to the engine starter harness with two wire ties.

85. Loosely secure the antenna cable to the dashboard with one wire tie loosely installed in step 70.

Q0N2303AG


FRONT

LEFT KNEE BOLSTER WIRE

TIE

ANTENNA CABLE

WIRE TIE

ANTENNA CABLE

WIRE TIE

VEHICLE HARNESS

DASHBOARD

FUSE BOX

20 of 27 AII 46215

Installing the Control Unit

86. Using isopropyl alcohol on a shop towel, clean the area where the urethane tape will attach.

87. Attach the one urethane tape to the vehicle unit as shown.

88. Plug the antenna cable and the engine starter harness 28-pin connector into the control unit.

Q0N2305AG

URETHANE TAPE

VEHICLE UNITClean with isopropyl alcohol.

Q0N2306AGENGINE STARTER HARNESS 28-PIN CONNECTOR

ANTENNA CABLE

CONTROL UNIT


89. Install the control unit bracket to the control unit.

90. Secure the clip from the engine starter harness fuse block, and the clip from the engine starter harness into the holes in the control unit bracket.

Q0N2307BG

CONTROL UNIT

CONTROL UNIT BRACKET

Q0N2308BG



HOLE

CLIP

HOLECLIP

FUSE BLOCK


91. Remove the vehicle flange nut that secures the vehicle bracket.

92. Install the control unit bracket on top of the vehicle bracket and align the control unit bracket with the edge of the vehicle bracket. Reinstall the vehicle flange nut. Install the 8 mm nut (supplied) on top of the vehicle flange nut.

Q0N2309AG


8 mm NUT

VEHICLE FLANGE NUT(reused)


8 mm NUT

VEHICLE BRACKET

VEHICLE FLANGE NUT

VEHICLE BRACKET

VEHICLE PANEL


Align.

(1112) 21 of 27

93. Secure the antenna cable and engine starter harness to the vehicle harness with one long wire tie.

94. Secure the antenna cable to the engine starter harness with one wire tie.

95. Bundle up the excess antenna cable, and secure it to the dashboard with the one wire tie loosely installed in step 85.

Q0N2310BG


FRONT

LONG WIRE TIE

ANTENNA CABLE

VEHICLE HARNESS

WIRE TIE

Q0N2311BG

ANTENNA CABLEBundle up the excess.

WIRE TIEDASHBOARD

22 of 27 AII 46215

96. Using isopropyl alcohol on a shop towel, clean the areas where the urethane tapes will attach.

97. Attach the two urethane tapes to the inside of the lower column cover.

98. Open the hood. Using isopropyl alcohol on a shop towel, thoroughly clean the hood where the caution label will attach.

99. Remove the adhesive backing from the caution label, and attach the caution label to the hood in the area shown.

Q090601AK

Clean with isopropyl alcohol.

URETHANE TAPES

LOWER COLUMN COVER(inside)

Q0N2011AG


CAUTION LABEL

HOODClean with isopropyl alcohol.


100. Check that all wire harness and cables are routed properly and that all connectors are plugged in.

101. Reinstall all removed parts.

102. Reconnect the negative cable to the battery.

103. Check the operation of the headlights and wipers.

104. Press and hold the radio power button for two seconds to restore the radio and navi (if equipped) system functions.

105. Reset the clock on vehicles without navigation.

106. Proceed to the REMOTE ENGINE STARTER REGISTRATION (Page 23) and FUNCTION CHECK (Page 26).


REMOTE ENGINE STARTER REGISTRATION

1. Acquire the PCM Code from ISIS.

2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the on (II) position.

3. Start the HDS, and click the car icon.

4. Input the VIN and other required information into the HDS, then click the check button.

792901AH

CAR ICON

752502AS

Input the VIN and other required information. CHECK BUTTON

(1112) 23 of 27

5. Select Honda Systems, then click the check button.

6. Select R/C ENG STARTER and click the check button.

752503AS

Select Honda Systems. CHECK BUTTON

752504AS

Select R/C ENG STARTER. CHECK BUTTON

24 of 27 AII 46215

7. Check that REMARKS is shown, then click the check button.

8. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button.

752505AS

Check that REMARKS is shown.

CHECK BUTTON

752506AS

Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT.

CHECK BUTTON


9. The following message will display: Obtain PCM code (IMMOBILIZER PCM CODE) from iN. This vehicles VIN will be required to obtain the password (USA). Click on the check button.

10. Input the PCM Code, then click the check button. NOTE: To ensure security, the PCM code (password) is changed everyday, so it is impossible to register the remote control engine starter if the dates of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same.

752507AS

Obtain PCM-code message.

CHECK BUTTON

752509AS

Input the PCM Code.

CHECK BUTTON


11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click on the check button.

12. The following message will display: Check that the engine can be started by the Transmitter. Click on the check button.

13. Perform the function test on page 26, then disconnect the HDS.

752510AS

The registration of the Remote Control Engine Starter Unit has been completed.

CHECK BUTTON

752511AS

Check that the engine can be started by the Transmitter.

CHECK BUTTON

(1112) 25 of 27

FUNCTION CHECK

Operating Conditions

The hood is closed

The shift lever is in park

The key is out of the ignition and the key is outside the vehicle

All doors and tailgate closed and locked

Inspection

1. Press the command button, and then, within 1 second, press the start button on the transmitter.

The engine should start if all operating conditions are met.

Does the engine start?

2. Press the command button on the transmitter and, within 1 second, press the stop button. The engine should stop.

Does the engine stop?

3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:

NOTE: After each test the ignition key must be cycled, or the drivers door must be opened and closed.

Move the shift lever out of the P position.

Unlock or open the doors or the tailgate.

Open the hood.

Insert the key in the ignition.

Press on the brake pedal.

Does the engine stop after each of these tests?

4. Check that the power windows and the moonroof do not function when the engine is started with the transmitter.

5. Start the engine again, press the command button on the transmitter two times and check the vehicle condition on the display.

6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away and in direct sight.

7. Insert the key in the ignition and start the engine, check the operation of the headlights and wipers.

Yes - Operation is normal.

No:

Make sure all Operating Conditions are met.

Check the engine starter harness connections.

Connect the HDS and check for an indicated failure.

(Refer to the appropriate service manual for details.)


No - Check the engine starter harness connections.


No - Check the engine starter harness connections.

732904AY

DISPLAY

START BUTTON

COMMAND BUTTON

STOP BUTTON

TRANSMITTER

26 of 27 AII 46215 (1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.

How to Program an Additional Transmitter

1. Connect the HDS to the data link connector.

2. Start the HDS and click on the car icon.

3. Input the vehicles VIN and other required information.

4. Select Honda Systems.

5. Select R/C ENG STARTER.

6. Select REGISTER NEW TRANSMITTER.

7. When Ready to program the new transmitter shows, select ENTER.

8. Press and release the Command button.

9. Press and release the Stop button.

10. Perform the function check on both transmitters.

NOTE: Only 2 remotes can be stored in the systems memory.

2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215 (1112) 27 of 27

Button1: Button2: Button3: Button4: Button5: Button6: Button7: Button8: Button9: Button10: Button11: Button12: Button13:

installation aii 12085 cr-v instructions starter … · remote control engine starter unit kit. p/n...

Documents