manufacturing 32

M/A-COM TECH ASIA INC

和康電訊股份有限公司

Title 文件名稱 Document No.:

文件編號 MFG-1232

MTA_Setup Procedure For R7181-38 Rev.:

版別 - Page: 1 OF 27

M/A-COM Technology Solutions Inc. CONFIDENTIAL INFORMATION SUBJECT TO NDA

The information contained in this document or material is the valuable and confidential property of M/A-COM Technology Solutions Holdings, Inc. and/or its subsidiaries or affiliates (collectively “MACOM”), provided to you subject to a non-disclosure agreement between you and MACOM solely for use in supporting MACOM’s business as and to the extent MACOM authorizes in writing from time to time. This information shall be held in strictest confidence and shall not be reproduced, published, disclosed to others, or used for any purpose except as and to the extent specifically authorized by MACOM in a separate written agreement. If permission is granted for reproduction, this legend must be included in any and all copies. This document or material shall be promptly returned to MACOM or destroyed upon request, completion of the use for which it was made available to recipient, or termination of MACOM’s relationship with recipient, whichever first occurs.

ATTENTION

USER OF THIS DOCUMENT IS RESPONSIBLE FOR

DETERMINING CURRENT REVISION LEVEL BEFORE

USING DOCUMENT.

Originated By: Rick Chen Date 2015/1/30

RF Test Engineer Approved By: Wilson Hsu Date 2015/1/30

Quality supervisor Approved By: Anson Cheng Date 2015/1/30

Technical Manager

Title :文件名稱 Document No.:




REVISION HISTORY

Revision Change Description CO NO. Date

- New release CO-015167 2015/1/30





1.0 Purpose 目的

Define setup procedure for package product R7181-38

2.0 Scope 範圍

R7181-38

3.0 Reference documents 參考文件

R7181-38-WF-001

R7181-38-WF-002

4.0 Definitions 名詞定義

N/A

5.0 Procedure 作業程序

5.1 Equipment setting





5.2. DST4 tester power on flow

5.2.1 Press Space bar 3 times upon encountering Figure 1 below.

5.2.2 Press ‘Y’ upon encountering figure 2 below. Then Follow DST4 Program Loading

Procedure on the succeeding instructions.

Figure 1 Figure 2

5.3. DST4 Program Loading Procedure

5.3.1 The main DST4 menu with latest revision will appear. From this menu choose “RUN TEST pROGRAM” using the up/down arrow keys and hit <enter>.

Press Space bar 3 times Press ‘Y’





5.3.2 Enter the correct production Test Program Name, i.e.”R7181AI”, and hit <enter>.

5.3.3 From the next menu choose “ pRODUCTION TEST ” for Final Test or “ qA TEST “ for QA gate using the up/down arrow keys and hit <enter>.

R7181AI





5.3.4 For the first Production Run sequence you must choose “ dUAL SITE - for dual site ITA

board or sINGLE SITE -for single site ITA board ” from the menu option, using the up/down arrow keys and hit <enter>.

5.3.5 Next, you must select “ HALT ON fAIL “ from the next menu option.





5.3.6 Next, enter the “dash number” marked on the device packages/ listed on Test LTC you are testing, i.e. 38.

5.3.7 Next, enter the “Lot Number” as listed on the device package/ Test LTC.





5.3.8 Next, enter the re-test number, “0” is for 1st pass and “1” is for the re-test of failures.

Flow for Re-test Number:

5.3.9 Next, enter the “Employee Number” of operator.





5.3.10 Next, select the correct “Temperature” from the menu as indicated on Test LTC. Make sure that the thermocouple temperature reading is 75C when testing at Hot Temperature. Thermocouple should not be attached when Testing Room Temperature and Cold Temperature

Note : PLEASE SEE Section 5.4 for Details.

5.3.11 Enter DUT number for socket but please make sure that the DUT number for the two socket is not the same and if you choose SINGLE TEST for item 4.4 only one socket number to be ask.(Ex.DUT#1 - 0 and DUT#2 - 1)





5.3.12 You will now be asked to verify the information you entered, which is displayed on the screen. If all the information is correct then enter ‘Y’.

5.3.13 If the information is not correct then do the following: enter ‘N’ and using the up/down arrow keys select the data field that needs to be changed. Hit <enter> and update it accordingly. Hit the <enter> button to confirm the change. To leave this menu and start testing hit the <ESC> key.





5.3.14 Next, you will be prompted to start testing.

5.3.15 Load the device to be Re-tested into the left-hand socket only.

5.3.16 Make sure the device is oriented correctly: device marking is upside down in reference to the front of the tester, as shown below.

5.3.17 Begin testing by either depressing the space bar, or the test button on the front panel of

the DST4 tester.

NOTE: See Section 5.5 for Details.





PASS/FAIL Observations:

FAIL

When the testing completes and the screen shows ‘FAIL’, and the red LED on the front of the DST4 ITA is illuminated, hit the re-test button on the front of the DST4 tester, or hit ‘r’ on the keyboard, to re-test the device. Only do this once. If the screen shows ‘FAIL’, and the red LED on the front of the DST4 ITA is illuminated again, remove the device from the left-hand socket and place it in the bin for all failing devices.

After Test, separate REJECT parts with a red sticker /clip tray with proper label as rejects.

PASS

When the testing completes and the screen shows ‘PASS’, and the green LED is illumated, put the device from the left-hand socket in the bin for all passing devices.

After Test, separate GOOD from REJECT parts with a green sticker / clip tray and properly label as BIN1.





5.4. R7181 test flow and conditions:

5.4.1 HOT TESTING

5.4.1.1 E/L TEST 2 (QS02-043) - Handler/ Temp : Manual / 75 +/-3 deg C - Good Bin : Bin 1 - Tester/ Test Program : DST4 / Refer to LTC - Yield and O/S Limit : Refer to LTC - 1x Mandatory Retest : If Final Test Yield is not met - Rejects Requirements : Scrap rejects if PASSED yield requirements

Oven Heating Procedure

5.4.1.1.1 Place the units to be tested inside the oven. 5.4.1.1.2 Set the Oven at 75 deg C +/- 3.0 5.4.1.1.3 After 30 minutes, get 1 tray of units and place it above a Hot Plate preset at

75 +/- 3 deg C. 5.4.1.1.4 Start Testing. Note : Get only 1 tray from the oven at a time to prevent sudden cool down Of units. 5.4.1.2 E/L TEST 3 (QS02-043) HOT TESTING CONDITION - Handler/ Temp : Manual / 75 +/-3 deg C - Good Bin : Bin 1 - Tester/ Test Program : DST4 / Refer to LTC - Yield and O/S Limit : Refer to LTC - 1x Mandatory Retest : If Final Test Yield is not met - Rejects Requirements : Scrap rejects if PASSED yield requirements





5.4.2 COLD TESTING 5.4.2.1 Freezer Cooling Procedure 5.4.2.1.1 Place the units to be tested inside the freezer. 5.4.2.1.2 Preset the freezer at - 6 deg C +/- 3.0 5.4.2.1.3 After 45 minutes, get units to be tested and place it on the socket. 5.4.2.1.4 Start Testing. Testing should commence within the span of 1 minute.

Note :Get only units to be tested from the freezer at a time to maintain unit temperature. No

RETEST should be done. Failed units should be put back to freezer for Cooling prior retest.

5.4.2.2 E/L TEST 4 (QS02-043) COLD TESTING CONDITION - Handler/ Temp : Manual / 0 +/- 3 deg C - Good Bin : Bin 1 - Tester/ Test Program : DST4 / Refer to LTC - Yield and O/S Limit : Refer to LTC - 1x Mandatory Retest : If Final Test Yield is not met - Rejects Requirements : Scrap rejects if PASSED yield requirements

5.4.3 AMBIENT / ROOM TESTING

5.4.3.11 Place the units for test on Room Temperature condition and start Testing.

5.4.3.2 E/L TEST 4 (QS02-043) AMBIENT / ROOM CONDITION - Handler/ Temp : Manual / ROOM - Good Bin : Bin 1 - Tester/ Test Program : DST4 / Refer to LTC - Yield and O/S Limit : Refer to LTC - 1x Mandatory Retest : If Final Test Yield is not met - Rejects Requirements : Scrap rejects if PASSED yield requirements Note :Change the Unit / DUT upon encountering 2X failures, Put the failed parts to Reject tray

for retest if yield requirement is not met.





5.5 DST4 Operations 5.5.1 With Switch Sensor

5.5.1.1 To start testing using the sensor, Place the thumb on the top slot shown on the Above Figure labeled A) Motion Sensor for Test.

5.5.1.2 To perform a retest , Place the thumb on the bottom slot shown on the above Figure labeled B) Motion Sensor to Re-Test.





5.5.2 Without Switch Sensor

5.5.2.1 Set the Omniview to the corresponding DST4 slot Number in reference to the

Connection at the back of the Omniview. Please see below figures. FRONT VIEW

BACK VIEW





5.5.2.2 Press ‘SPACE BAR’ to start the testing of the corresponding DST4 set on the above

Omniview setting. Press ‘R’ for Re-Test

6.0 Appendix 附件

N/A

manufacturing 32

Documents