가솔린연료계통의개발시험종류및 방법 gasoline fuel supply system tests.pdf ·...
TRANSCRIPT
가솔린 연료계통의 개발 시험 종류 및방법방법
목차 1)유럽 및 한국 규제의 대책 시스템
미국 수출 사양의 시스템 구성도
1. Fuel Filler Inlet Requirements Evaluation2. Filler Cap Locking Lip Angle Requirements Evaluation3. Fill Pipe Access Zone Evaluation4 Fuel Tank Filling Performance Tests4. Fuel Tank Filling Performance Tests4-1. Fuel Tank Filling Performance Tests4-2. Fuel Tank Filling Performance Tests5. Tickle Fill 성능 시험
6. Bench Fuel Loss 시험
7. 연료 탱크의 가혹/극단 환경 재현 시험
7-1 연료 탱크의 가혹/극단 환경 재현 시험
8. 경사 주차 차량의 주유성 재현 시험
9 고장 주유장치 재현 시험9. 고장 주유장치 재현 시험
10. 경사 주차 차량의 주유성 재현 시험
미래엔진 ㈜ Future-Engine.Co., Ltd., www.future-engine.com, 031-355-7218, [email protected] 2
목차 2)목차 2)11. Fuel Tank Vent Performance 시험
12. Refueling (Round-Up) 시험
13. High Vapor Generation 시험
14. 고주유량 주유 시험
15. Top-Off 주유시험
16. Dynamic Fuel Carry Over test 17. Cool Fuel into Hot Fuel Tank18. 극한 주유 온도 시험
19. Fill Nozzle 평가 시험
20 필러 튜브 안의 액체 연료 상태 평가20. 필러 튜브 안의 액체 연료 상태 평가
21. Refueling Idle Test22. Overnite 캐니스터 / 퍼지 특성 평가
23 경사 주차중의 Overnite 캐니스터/퍼지 특성 평가23. 경사 주차중의 Overnite 캐니스터/퍼지 특성 평가
24. 산악 주행 시험
25. Commercial Refueling, City Driving31. ORVR Control Valve Tests –132. ORVR Control Valve Tests –233. ORVR Control Valve Tests – Durability Test34. Permeation Loss Test
미래엔진 ㈜ Future-Engine.Co., Ltd., www.future-engine.com, 031-355-7218, [email protected] 3
목차 3)목차 3)41. Canister Butane Working Capacity Tests
51. 인증 시험 – ORVR 시험
52. Spit Back 시험
53. 인증 시험 – Canister Load Rate 시험
54. 인증 시험 – Basic Condition System Shutoff Performance Test51. 인증 시험 – Refueling Consistency 시험
61. 총합 개발 시험 –Quality Assurance 62. Design Verification63. Production Validation64. Continuous Conformance Test
70. ORVR Control Valve 및 inlet Valve 등 주요 부품의 Reliability Tests71. Control Valve 장착
72. 포트 강도 시험
73. 낙하 시험
74. Permeation Test
75. 충격 시험
미래엔진 ㈜ Future-Engine.Co., Ltd., www.future-engine.com, 031-355-7218, [email protected] 4
목차 4)76. High Flow Corking시험
77. Initial Shutoff and Topoff 시험
78. Vent Flow Test
79. Back Flow Test
80. Pressure Relief Flow and External Leakage
81 개변압력 시험81. 개변압력 시험
82. 롤오버 니플을 통한 유량 측정
83. 롤오버 폐변 각도 측정
83. 롤오버 폐변 각도 측정
85. Slosh Cycle Test System
80. Pressure Relief Flow and External Leakage
81. Life Test – 압력 테스트
82. 진동 시험용 Jig의 제작 방법
83. 내분진 시험83. 내분진 시험
84. 내습 시험
85. 부품 보관 상태 재현 시험
시험
미래엔진 ㈜ Future-Engine.Co., Ltd., www.future-engine.com, 031-355-7218, [email protected] 5
86. Salt Spray 시험
유럽 및 한국 규제의 대책 시스템유럽 및 한국 규제의 대책 시스템특징: ORVR 규제가 없으며 Enhanced EVAP이 아니기 때문에 구조간단, 캐니스터 소용량
FuelFilter
Fuel Rail
Fuel Supply Hose
Fuel Return HoseFuel Tubes and Hoses
CheckValve
Surge TankEvap. Hose
Evap HosePurge
SolenoidValve
Roll OverValve
Roll OverValveValve Valve
6
미국 수출 사양의 시스템 구성도미국 수출 사양의 시스템 구성도ORVR 규제를 대응하여야 하고 Enhanced EVAP 규제를 대응할 수 있도록 구조 설계.
FuelFilter
Fuel Rail
Fuel Supply Hose
Fuel Return HoseFuel Tubes and Hoses
Surge Tank Evap HosePurge
SolenoidValve
Roll Over Roll OverValve Valve
Shut-Down Valve
7
1 Fuel Filler Inlet Requirements Evaluation1. Fuel Filler Inlet Requirements Evaluation
1. 개요 미국의 연방 및 캘리포니아 주 법규에 의한 연료 탱크 계 요구 조건의 평가
2. References 1) US Federal Register Vol.61, No 23, P.3836
CFR 80-24
2) CARB Mail-Out #94-08 “Specifications for Fill Pipes and2) CARB Mail Out #94 08 Specifications for Fill Pipes and
Openings of Motor Vehicle Fuel Tanks”
3) CARB MAC #96-11
3 목적 1) 촉매의 유연 오염 방지3. 목적 1) 촉매의 유연 오염 방지
2) Stage II Vapor Recovery Nozzle을 사용한 주유성 확보
4. 시험 방법 상세한 시험 방법 및 시험 장비 관련 정보는 미래엔진(주)에 문의해 주시기
바랍니다.
5. 시험 장비 상동
6 개발 목표 1) Fill Rate 2) PSO 3) Spillage 4) Spit Back 5) Fill Pipe Access Zone6. 개발 목표 1) Fill Rate 2) PSO 3) Spillage 4) Spit Back 5) Fill Pipe Access Zone
6) SAE J1114, SAE J829B 7) ORVR Regulation
7. 기타
8
7 연료 탱크의 가혹/극단 환경 재현 시험7. 연료 탱크의 가혹/극단 환경 재현 시험
1. 개요 1) 극단적인 상황에서의 주유성 평가
2. References 1) 40 CFR 80.24 “Controls Applicable to Motor Vehicle Manufacturers, Regulations of Fuels and Additives”
2) 40 CFR 86.132-96, Vehicle Preconditioning”
3) ASTM D323 90 “Standard Test Method for Vapor Pressure of3) ASTM-D323-90 “Standard Test Method for Vapor Pressure of Petroleum Products” – RVP
4) CCR Title 13, Section, “Specifications for Fill Pipe and Openings of Motor Vehicle Fuel Tanks”
3. 시험 방법 미래엔진(주)에 문의할 것.
4. 측정 항목 1) PSO 발생회수
2) 증기 시스템의 압력 분포
3) 노즐 셧오프 Cleanliness
4) 벤트 시스템으로의 액상 연료 돌입량.
5. 시험 장비 Refueling Test System, SHED
6. 개발 목표 O PSO, o.o 흔 spit Back, 0.0 ml Intrusion, >95% Useable Fuel Tank Capacity after 3rd Shutoff
7. 기타
16
8 경사 주차 차량의 주유성 재현 시험8. 경사 주차 차량의 주유성 재현 시험
1. 개요 1) 경사지 주차 차량의 주유성 재형 시험
2. References 1) 40 CFR 80.24 “Controls Applicable to Motor Vehicle Manufacturers, Regulations of Fuels and Additives”
2) 40 CFR 86.132-96, Vehicle Preconditioning”
3) ASTM D323 90 “Standard Test Method for Vapor Pressure of3) ASTM-D323-90 “Standard Test Method for Vapor Pressure of Petroleum Products” – RVP
4) CCR Title 13, Section, “Specifications for Fill Pipe and Openings of Motor Vehicle Fuel Tanks”
3. 시험 방법 미래엔진(주)에 문의할 것.
4. 측정 항목 1) 증기 제어 계통의 압력 거동
2) 벤트 혹은 외부로의 연료 유출
5. 시험 장비 Refueling Test System, SHED
6. 개발 목표
7. 기타
18
9 고장 주유장치 재현 시험9. 고장 주유장치 재현 시험
1. 개요 1) 고장 주유 장치를 사용하여 주유할 때의 현상 평가
2. References 1) 40 CFR 80.24 “Controls Applicable to Motor Vehicle Manufacturers, Regulations of Fuels and Additives”
2) 40 CFR 86.132-96, Vehicle Preconditioning”
3) ASTM D323 90 “Standard Test Method for Vapor Pressure of3) ASTM-D323-90 “Standard Test Method for Vapor Pressure of Petroleum Products” – RVP
4) CCR Title 13, Section, “Specifications for Fill Pipe and Openings of Motor Vehicle Fuel Tanks”
3. 시험 방법 미래엔진(주)에 문의할 것.
4. 측정 항목 1) 연료 과다 주유 특성
2) 시스템 압력 응답 거동 평가
3) 연료 누출부위 확인
4) 시스템 손상 방지 가능성 평가
5. 시험 장비 Refueling Test System, SHED
6. 개발 목표
7. 기타
19
10 경사 주차 차량의 주유성 재현 시험10. 경사 주차 차량의 주유성 재현 시험
1. 개요 1) 경사지 주차 차량의 주유성 재형 시험
2. References 1) 40 CFR 80.24 “Controls Applicable to Motor Vehicle Manufacturers, Regulations of Fuels and Additives”
2) 40 CFR 86.132-96, Vehicle Preconditioning”
3) ASTM D323 90 “Standard Test Method for Vapor Pressure of3) ASTM-D323-90 “Standard Test Method for Vapor Pressure of Petroleum Products” – RVP
4) CCR Title 13, Section, “Specifications for Fill Pipe and Openings of Motor Vehicle Fuel Tanks”
3. 시험 방법 미래엔진(주)에 문의할 것.
4. 측정 항목 1) 증기 제어 계통의 압력 거동
2) 벤트 혹은 외부로의 연료 유출
5. 시험 장비 Refueling Test System, SHED
6. 개발 목표
7. 기타
20
11 Fuel Tank Vent Performance 시험11. Fuel Tank Vent Performance 시험
1. 개요 1) 연료 탱크 용량의 15% ~ 85% 주유 중 환기성능의 평가
2. References 1) 40 CFR 80.24 “Controls Applicable to Motor Vehicle Manufacturers, Regulations of Fuels and Additives”
2) 40 CFR 86.132-96, Vehicle Preconditioning”
3) ASTM D323 90 “Standard Test Method for Vapor Pressure of3) ASTM-D323-90 “Standard Test Method for Vapor Pressure of Petroleum Products” – RVP
4) CCR Title 13, Section, “Specifications for Fill Pipe and Openings of Motor Vehicle Fuel Tanks”
3. 시험 방법 미래엔진(주)에 문의할 것.
4. 측정 항목 1) 연료 탱크의 Vent 특성
5. 시험 장비 Refueling Test System, SHED
6. 개발 목표 0.020 “ or larger equivalent orifice venting
7. 기타
21
32 ORVR Control Valve Tests 232. ORVR Control Valve Tests –2
1. 개요 ORVR Control Valve 의 개발 시험 – 1
2. Test Modes 17) 경사지 팽창 시험
18) Slosh Test
19) Durability Test
3. 시험 방법 미래엔진(주)에 문의할 것.
4. 측정 항목
5. 시험 장비 Refueling Test System, SHED
6. 개발 목표
7. 기타
37
33 ORVR Control Valve Tests Durability Test33. ORVR Control Valve Tests – Durability Test
1. 개요 ORVR Control Valve 의 개발 시험 – Durability/Reliability Tests
2. Test Modes 1) Life Test – Ambient
2) Life Test – Low temp
3) Life Test – High Temp
9) Thermal Shock
10) Endurance Tests
11) Short Term Durability Test
4) Vibration Test –Low/High/Ambient Temp
5) Dust test
)
12) Test to Failure
13) Vehicle Tests
6) Salt Spray Test
7) Humidity Test
8) Storage Temperature / OperationOperation
3. 시험 방법 미래엔진(주)에 문의할 것.
4. 측정 항목
5 시험 장비 Refueling Test System SHED5. 시험 장비 Refueling Test System, SHED
6. 개발 목표
7. 기타
38
34 Permeation Loss Test34. Permeation Loss Test
1. 개요 정상적인 야간 주차 중의 캐니스터 거동 평가
2. Test Modes 1) Refueling
2) Drive/Soak 1
3) Drive/Soak 2
4) Drive/Soak 3
5) Soak and Evaluation
3. 시험 방법 미래엔진(주)에 문의할 것.
4. 측정 항목
5. 시험 장비 Refueling Test System, SHED
6. 개발 목표
7. 기타
39
51 인증 시험 ORVR 시험51. 인증 시험 – ORVR 시험
1. 개요 ORVR 규제의 적합성 시험
2. References 1) US Federal Register Vol.61, No 23, P.3836
CFR 80-24
2) CARB Mail-Out #94-08 “Specifications for Fill Pipes and ) p p
Openings of Motor Vehicle Fuel Tanks”
3) CARB MAC #96-11
3 목적 ORVR 인증3. 목적 ORVR 인증
4. 시험 방법 상세한 시험 방법 및 시험 장비 관련 정보는 미래엔진(주)에 문의해 주시기
바랍니다.
5. 시험 장비 상동
6. 개발 목표 0.05 g/G
7 기타7. 기타
41
52 Spit Back 시험52. Spit Back 시험
1. 개요 주유 중 Spit 발생이 없음을 입증하는 시험
2. References 1) US Federal Register Vol.61, No 23, P.3836
CFR 80-24
2) CARB Mail-Out #94-08 “Specifications for Fill Pipes and ) p p
Openings of Motor Vehicle Fuel Tanks”
3) CARB MAC #96-11
3 목적3. 목적
4. 시험 방법 상세한 시험 방법 및 시험 장비 관련 정보는 미래엔진(주)에 문의해 주시기
바랍니다.
5. 시험 장비 상동
6. 개발 목표
7 기타7. 기타
42
53 인증 시험 Canister Load Rate 시험53. 인증 시험 – Canister Load Rate 시험
1. 개요 캐니스터 퍼지 로드 성능의 입증
2. References 1) US Federal Register Vol.61, No 23, P.3836
CFR 80-24
2) CARB Mail-Out #94-08 “Specifications for Fill Pipes and ) p p
Openings of Motor Vehicle Fuel Tanks”
3) CARB MAC #96-11
3 목적3. 목적
4. 시험 방법 상세한 시험 방법 및 시험 장비 관련 정보는 미래엔진(주)에 문의해 주시기
바랍니다.
5. 시험 장비 상동
6. 개발 목표
7 기타7. 기타
43
54 인증 시험 Basic Condition System Shutoff54. 인증 시험 – Basic Condition System Shutoff Performance Test1. 개요 1차 Shutoff까지의 총 주유량 요건의 만족 여부 입증
2. References 1) US Federal Register Vol.61, No 23, P.3836
CFR 80-24
2) CARB Mail-Out #94-08 “Specifications for Fill Pipes and ) p p
Openings of Motor Vehicle Fuel Tanks”
3) CARB MAC #96-11
3 목적 U bl 용량의 95% 이상3. 목적 Useable 용량의 95% 이상
4. 시험 방법 상세한 시험 방법 및 시험 장비 관련 정보는 미래엔진(주)에 문의해 주시기
바랍니다.
5. 시험 장비 상동
6. 개발 목표
7 기타7. 기타
44
51 인증 시험 Refueling Consistency 시험51. 인증 시험 – Refueling Consistency 시험
1. 개요 주유 환경에 관계없이 주유성이 일정함을 입증
2. References 1) US Federal Register Vol.61, No 23, P.3836
CFR 80-24
2) CARB Mail-Out #94-08 “Specifications for Fill Pipes and ) p p
Openings of Motor Vehicle Fuel Tanks”
3) CARB MAC #96-11
3 목적3. 목적
4. 시험 방법 상세한 시험 방법 및 시험 장비 관련 정보는 미래엔진(주)에 문의해 주시기
바랍니다.
5. 시험 장비 상동
6. 개발 목표
7 기타7. 기타
45
70. ORVR Control Valve 및 inlet Valve 등 주요 부품의Reliability Tests
50
71 Control Valve 장착71. Control Valve 장착
제어 밸브
롤오버니플
캐니스터리플
Seal 및록크 링
연료 탱크상면
상세한 정보는 미래엔진(주)에 문의해 주시기
51
상세한 정보는 미래엔진(주)에 문의해 주시기바랍니다.
78 Vent Flow Test78. Vent Flow Test
x(1)
배플
상세한 정보는 미래엔진(주)에 문의해 주시기
미래엔진(주) Future-Engine Co., Ltd, www.future-engine.com, 031-355-7218, [email protected] 58
상세한 정보는 미래엔진(주)에 문의해 주시기바랍니다.
79 Back Flow Test79. Back Flow Test
x(1)
배플
상세한 정보는 미래엔진(주)에 문의해 주시기
미래엔진(주) Future-Engine Co., Ltd, www.future-engine.com, 031-355-7218, [email protected] 59
상세한 정보는 미래엔진(주)에 문의해 주시기바랍니다.
80 Pressure Relief Flow and External Leakage80. Pressure Relief Flow and External Leakage
x(2)
배플
상세한 정보는 미래엔진(주)에 문의해 주시기
미래엔진(주) Future-Engine Co., Ltd, www.future-engine.com, 031-355-7218, [email protected] 60
상세한 정보는 미래엔진(주)에 문의해 주시기바랍니다.
81 개변압력 시험81. 개변압력 시험
x(2)
배플
상세한 정보는 미래엔진(주)에 문의해 주시기
미래엔진(주) Future-Engine Co., Ltd, www.future-engine.com, 031-355-7218, [email protected] 61
상세한 정보는 미래엔진(주)에 문의해 주시기바랍니다.
83 내분진 시험83. 내분진 시험분진 시험 챔버
모든 니플의
연료 탱크 혹은 탱크 모사 장치
모든 니플의개폐 상태?
상세한 정보는 미래엔진(주)에 문의해 주시기
미래엔진(주) Future-Engine Co., Ltd, www.future-engine.com, 031-355-7218, [email protected] 69
상세한 정보는 미래엔진(주)에 문의해 주시기바랍니다.