http www.pugetsoundanglers

Upload: gwp5834

Post on 29-May-2018

219 views

Category:

Documents


0 download

TRANSCRIPT

  • 8/9/2019 Http Www.pugetsoundanglers

    1/17

    Downrigger Trolling for SalmonDownrigger Trolling for SalmonDownrigger Trolling for SalmonDownrigger Trolling for SalmonWHY FISH BITE, Click Here

    DOWNRIGGERS ;DOWNRIGGERS ;DOWNRIGGERS ;DOWNRIGGERS ; The choice of downriggers could get to be a lengthy session all by itself, as therewill be many opinions as to which is best. I have personally used Cannon manuals, Penn manuals,& Scotty manual & electrics. Each one has different features, some of a benefit over others. Mysuggestion is to go with a friend who has other brands & get a chance to use as many as possiblebefore you lay out the amount of cash involved. I had never even seen a downrigger used before Ipurchased my Cannons & I had a very steep learning curve. The reason I got the Cannons was Iknew a salesman who gave me a good deal on them. After I had a chance to see how the Scottyelectrics were used by a Alaskan salmon guide, when I sold that boat, I gave the guy a good dealon the whole package.

    I would not want a manual version where the handle rotated as the line was being let out. Thiscan be an arm breaker. One boat I was on that had an old Penn manual, & this was the situation.The Cannon manual, you rotated the crank handle slightly back allowing the line to go out & bymoving it farther back, it creates a cam type brake. This worked, but I was always afraid that agood jolt would brake something & it required a good cleaning & oiling frequently to keep it fromseizing up if used in saltwater.

    The Scotty electrics are a good design, & have been constantly improved. If you take it to a repaircenter for any problem, like even a uneven drag, most time they will update it to the newest typeof parts for no cost.. They have a 2 way switch on the upper arm control box. This box has a slot

    Downriggers pay off for Sitka Alaskan King Salmon

    Page 1 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    2/17

    that the wire is run thru. It has a kind of pivoting door that is controlled by the switch on the top.This switch has a black outer ring, & an inner green button. To raise it, you can push this greenbutton & as long as you hold it down the motor will bring in the wire. However if you want to haveit come in automatically, you rotate the outer ring. This also sets the gate to where the "buttons"you have previously set on the wire as your stop position, a location that when they pass thru thisgate, the switch is tripped off. These buttons now come in a package of both brightgreenish/chartreuse & black ones. It is recommended that you put one of each color on right nextto each other. This gives you a second one as a security to keep both of them from being slid out

    of position & the green one is easy to see when it is coming up. Scotty is one brand that willretrieve a 15# ball from deeper depths.

    You want to set these stops so that the ball is not pulled all the way up. As explained below in theDownrigger Weights section, I like to have the ball stop so that it is still just in the water. I havea shock cord long enough that I can now grab it & pull everything in then place the ball in a BallBaby nest. Raising the 12 or 15# ball out of the water is asking for a dented or crashed hull side.

    When letting any of them out, do it in a smooth even motion. If it goes too fast, the release clip &the line may tangle around the wire. And if it goes too fast, & when you have to stop it it may beso sudden that you fray or break the wire, or have the terminal snap off.

    You will want to carry some spare parts for any make that you have. You can always loose somebolts, blow a fuse, fray a wire, or break a belt. I usually carry a Scotty manual unit as a backup &

    it mounts in the same brackets as my electric units. Simply because it is cheaper & a lot lighterthan the electric units. And a spare can save the day if you have planned your outing, taken thetime off, & possibly traveled some distance for your day on the water. You can then repair the badone or replace the wire on shore later.

    Scotty electrics have a built in hand crank built into the unit just in case the belt breaks orsomething happens to the connector & you have to manually crank it up.

    The spools need to be washed off after usage especially if used in saltwater. The best is to washthem off with one of the salt dissolving products. One being a product called Salt Away. Wash thewhole boat & internals of the motor with this product. Then rinse off with normal water. If youdo not clean the downrigger wire, it can start corroding. I had one brand of replacement wire thatrotted in one year. Buy a longer replacement able than they come with. This way you canshorten the terminal end as it becomes curled, or even if you snag bottom & have it broken off, youmay still have enough to just replace the snap & reattach another ball.

    RODS ;RODS ;RODS ;RODS ; The rods used for downrigger fishing are usually 8' 6" & of a special design simply called"Downrigger Rods". They need to be a stiff enough butt section, yet have a lighter tip section sothat they can be cranked down to just before the release is tripped. In use, the rod is archedgreatly. What this does is place a lot of strain on the line & the rod, with a minimal amount of slackfrom the release to the rod. When you let the line out off the downrigger & stop the ball, youprobably will then have to reel in slightly to take out all the slack in your line. I have found that if Ipull the line back in at this point with one hand & reel in the slack with the other, I can "feel it"better. I want the slack taken completely out & have the release pulled up to just before itreleases prematurely. If you accidentally trip it off occasionally you are getting it about right.When the fish hits, the rod snaps up, automatically setting the hook.

    If you use a lighter rod you do not get this automatic hook setting action. Longer "noodle" rodsare also not considered desirable here for the same reason. This is not to say they can not be used,

    but if you do, you will have to be ever watchful & as soon as a hit is detected, reel in as fast aspossible to take up the line slack & get into the fish.

    ROD ANGLEROD ANGLEROD ANGLEROD ANGLE ;Set the rods at about a 45 degree angle rearward to achieve the desired effectdescribed above. If your rod is pointing rearward & down lower more, it CAN NOT achieve any ofthis automatic hook setting action. The rod seems to work best if mounted pointing to the rearinstead of to the side, as you will have a lot of side strain on the rod. However this will depend onwhere on your boat you have the downrigger mounted, & the DR rod holder you are using.

    Some west side of Vancouver Island Canadian guides seem to want to use the 10 1/2' moochingrod as an all-around rod. This is not an ideal trolling rod by any means, especially if it is placed 90degrees to the side of the boat as an extension of the downrigger arm. They then also want to run

    Page 2 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    3/17

    the flasher 60' + behind the clip. What this does is, there is so much belly in the fish line & withthe long "noodle rod", that if you get a hit, this limp rod does not set the hook and it may not eventrip the clip. Your only hope is to, as SOON as the rod tip twitches, grab the rod &REEL VERYFAST. If you come in empty, well, then you missed the fish. On the other hand if when you get allthe slack reeled in & something is wriggling on the other end, you lucked out.

    REELS ;REELS ;REELS ;REELS ;The main concern is to have a reel with a good smooth drag. If you have a reel that is old& or not maintained that has a drag that is erratic that will allow the line to be only stripped off in

    spurts, this is an invitation to loose a GOOD fish. The smaller fish will probably not be a problem,but a larger fish, when running, will not have the same constant strain applied. This then mayallow it to stop at the "hard spot". Next run will be starting with more strain, & possibly break offor pull the hooks out.

    Most commonly used reels will be the star drag, level wind reel. You may not really need a largecapacity reel, since you are in a boat & do have the ability to chase the fish if need be, but readabout this below. An Ambassedeur 5500, Penn 310 GTI, Shimano Triton 200G, or ShimanoCalcutta are some of the preferred ones. The new Shimano Tekota 600 looks to be another winneralso. It is very seldom that more than 100 yards of line is really needed. That said however, Ilike to run reels that I can spool with 250 yards of 25# monofilament line. I have seen big fishtake out line FAST in the opposite direction that you are trolling, by the time you realize what ishappening, you do not have time to pull the other gear in & do a chase. Remember you are boundgreatly by still having your downrigger wires in the water.

    The newer reels that have line counters will also help you return to a "Strike Zone" if conditionsallow. The Shimano Tekota line counter reels cost in the $180 range. Okuma MagdaPro linecounter series appear to the same & made for Cabellas as the DepthMaster II series. Cabellas DM-20 or the larger DM-30 are good reels for $40, with the Okuma slightly higher. I am not impressedwith the Shakespeare Tidewater series line counter reels as the drag is overly stiff.

    If you use a reel capable of holding 250 yards of 25# or so of line, you can use it one year, & thenext year swap ends of the line on the spool for fresh line on the normally used section (top) forthe next season.

    Do not make the mistake of using a steelhead rod & reel with 10# line for salmon on a downriggerif you are in an area where you may hook into a 30# plus fish. The reason is that when you aretrolling with multiple lines in the water, and you hook into a hog, it may take longer than yourealize just to identify what may be on the other end, as sometimes they tag along. If you are

    mooching, that is entirely different, as you do not have all the other semi-permanent gear(downrigger wire) in the water & you can move quickly if you have to while the other fishermenreel in.

    LINE ;LINE ;LINE ;LINE ;Here is where you will get as many different ideas as there is line out there. The normallyused type is monofilament. The suggestion is to find one brand that you are comfortable with &stay with it. You however need a line that is abrasion resistant enough to not be effected byrepeated use of the downrigger release clip. You also need a line heavy enough to pull the flasher& rest of the gear. Some will use 15# line for the smaller winter Blackmouth, & go up a notch to20# when the fish get larger during the summer & fall. If you are ocean fishing, the old standby is25# monofilament. With the newer bright colored lines becoming available, there is one aspectthat you may want to consider. That is use a bright green or yellow if you are fishing where thereis a chance of seals trying to take your fish. If Mr. seal does take the fish, as soon as possiblelighten up on the pressure so he will not have a chance to break your line off. Then chase them &

    keep the boat above him. This is where the bright colored line helps, as us older codgers can't seequite as well as we used to. The seal has to come to the surface to get a breath & eat the fish.When he hits the surface & takes a gulp, you can usually get the hurting or dead fish back beforethe seal can recover.

    With the advent of spectra type braided lines like Fireline, PowerPro etc. currently on the market,many fishermen have went to them. I will not argue one way or the other here, except that I havefound the spectra lines, being smaller dia. do have the problem if you use the small sizes (aboutequal to mono poundage) as they tend to cut into the other line on the spool if a big fish startspulling. This can create essentially the same thing as a backlash in the rest of the line on the reel& can give you the chance for the big fish to pull the hook out or break the line. Therefore manywho use the newer lines go to a larger size than needed, just to keep the line from cutting into the

    Page 3 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    4/17

    spool. When the larger dia. line is used then part of the benefits have diminished.

    KNOTS ;KNOTS ;KNOTS ;KNOTS ; In any fishing the knot is a very important factor, most all of the older style knots are notthat effective on the new spectra type lines. Therefore it is recommended you consider using thesimple little tool called "Knots for All", http://www.tie-master.com/ it is a 5" plastic tool that facilitates &makes knots on the new line possible. This simple tool was designed by fishing guide Joe Little.When the spectra type lines first came out he tested a 15# spectra with the common knots & itbroke at the 15#, but using this tool & his knot, it broke at 34#.

    When tying leaders, the safest way to tie the leader onto the hook is to wrap it left handed, thisplaces the leader around the solid part of the eye, and not laying on the cut end of the eye that inagainst the shank. With GOOD hooks it may make no difference, but many times if you get a lostfish due to a cut line at the hook, you will find that the leader was pulled into this sharp cut off endof the eye & you will have a small pig's tail at the cut.

    At times you will want a cut plug to only have the front hook in the bait, with the back hooktrailing, with this you then need to tie your leaders appropriately.

    SWIVELS ;SWIVELS ;SWIVELS ;SWIVELS ;The most common swivels used for saltwater fishing will be the barrel, bead chain andball bearing swivel. Each one has it's place. However when trolling, it is suggested that you getthe best available. If you want to test the efficiency of different swivels, a simple thing is to takeabout 12-15" of dacron line, tie both ends to the upper end of a swivel. Then tie a mono dropper to

    the bottom of the swivel and then about 5 or 6" to a 2 ounce cannonball weight. The upper loopeddacron will make it easy to hang onto. Now quickly spin the weight. Time the difference betweeneach swivel before the spinning stops. You will also be amazed at the differences in bead chain,barrel, cheap ball bearing swivels & the better Sampo brand.

    DODGERS & FLASHERSDODGERS & FLASHERSDODGERS & FLASHERSDODGERS & FLASHERS ; The big difference between dodgers & flashers is the way they run in thewater when being trolled. Dodgers are usually rounded on the ends and slightly cupped both ends,they wobble back & forth, or have a swaying side-to-side action. Dodgers are not generally aseffective below about 60, because color is filtered out at that depth & they do not make any noiseas an attractor.The flasher develops a full 360 degree rotation. As a general rule flashers work better at a

    slightly faster speed that dodgers do. Flashers have to rotate, they also create noise, -- go fastenough to achieve this action. The old brass Abe 'n Al of 50 years ago was one of the betterknown flashers. The Canadian Hot Spot plastic flasher seems to be the one most fishermen use

    now. The large size, the 11" Glo Green seems to be the preferred color for Puget Sound & theocean, while the 11" Red seems to be preferred color by the locals in Canada's Barkley Sound.Charge the Glo versions with a camera flash for better visibility in deeper water.

    New for 2003 is a flasher made by Pro Troll, called an E-Chip. It has a small metal tube about3/16" dia. & 5/8" long glued into the rear section. This is supposed to emit a slight electricalcharge about equal to baitfish being frightened. A plug similar to the Apex, but called the StingKing has this same chip in it. From what experience I have had,IT WORKS.

    11" Hot Spot Flasher on left, 8" Coyote on bottom,with a Les Davis Dodger on top right & Pro-Troll

    with chip on RH bottom

    Common size & colors of Fish Flash, with #2Metric spinner on one as an extra attractor

    Page 4 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    5/17

    FISH FLASH ;FISH FLASH ;FISH FLASH ;FISH FLASH ;This rotary attractor has been around for the past 10 years or so, & is made by BigAl's Tackle Co. It is a plastic triangle with the rear widest wings bent so the flasher rotates. Theyare made in 4 sizes, Mini ( 4"), Small ( 6" ), Medium ( 8") & Large (11"). These have proventhemselves for many types of fishing, both saltwater & freshwater. The one thing about themthere is very little drag, since they spin on their axis. They are available in many different metallicreflective & glo-in-the-dark, the more popular colors seem to be chartreuse, chrome, red, limegreen or blue plaid, with the new purple coming in recently.

    What these were first found to be very good for locally, was Chinook fishing in estuary waters inthe fall where the water had enough turbidity to restrict visibility. When using them, it may beadvisable to add a Sampo ball bearing swivel to your mainline, in addition to the original suppliedswivels of the Flash to help eliminate tine twisting. I have tested the large & medium units in theocean & can not really tell if one is any better than the other down to about 70', below thatpossibly the larger may be benificial. The mini & small units have proven themselves onlandlocked Kokanee.

    OK, I KNOW THIS IS A DOWNRIGGER ARTICLE, BUT ;OK, I KNOW THIS IS A DOWNRIGGER ARTICLE, BUT ;OK, I KNOW THIS IS A DOWNRIGGER ARTICLE, BUT ;OK, I KNOW THIS IS A DOWNRIGGER ARTICLE, BUT ; These Fish Flashes can also be connectedabout 12" behind a diver. I have tried them attached directly to a diver, but when that close, thedisturbance of the diver effects the spin of the Fish Flash. When using this diver set-up, I use onlya 36"- 48" leader for normal salt water fishing. One additional add on would be to add a Metric #2spinner directly on the rear of this to increase it's effectiveness in that it does basically the samething as the E-Chip. If using them by themselves as trolling, without a diver or downrigger, youmay want to also add a rudder keel between the mainline & the Flash.

    The illustration below has worked well for Coho off the stern & out about 60', it will also takeChinook. You need about 12"-16" dacron line between the Deep Six diver & the Fish Flash to getrid of the turbulance of the diver. The mooching leader needs to only be about 36" & place a plasticbead on the leader between the Spi-N-Glo & the hooks as a bearing. Not scent or bait is reallyneeded. Run your downriggers off the side & put this rig right off the stern in a rodholder & waitfor the action. I like the Deep Six over all other divers in that you can adjust the trip off by thetension on the clamp. It is also a lot easier to trip from the rod, as compared to the other diverslike the Pink Lady, where they need to be tripped by the fish. You are supposed to be able to tripthe others from the rod by throwing slack & then picking it up again, but they don't seem to workas advertised most of the time.

    In both of the illustrations below, you will see a 1 to 4 oz round lead sinker attached to a slider onthe mainline resting just above the line release clip. This is an option that may gain you a fishoccasionally as explained in the section below "No Attractors for Coho". A flasher or dodger couldalso be substituted for this Fish Flash.

    Fish Flash behind Deep Six with Spi-N-Glo for Coho

    A Fish Flash attached to a downrigger unit. Note the lengths may not be toscale

    Page 5 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    6/17

    ACE IN THE HOLE ; ACE IN THE HOLE ; ACE IN THE HOLE ; ACE IN THE HOLE ; This method shown below, of trolling is using a flasher attached to thedownrigger ball instead of on the mainline. The appealing thing here is that you do not use theflasher or any weight on your line or leader, just your bait or lure. Have the flasher back about30" behind the ball & attached directly to it. No lure behind it, as it is simply an attractor for thelure close above. Now attach your release clip on the mainline far enough up so that the flashercan not raise up while descending & tangle with the leader. You want the lure to be just above &behind the flasher.

    With the above set up you can run a lighter rod & with the lighter rod, you can tell quickly if youhave a small shaker fish hooked. This is a proven method for Blackmouth. You can use no weightor a light one as a slider just above the release as described in the following paragraph.

    NO ATTRACTORS FOR COHO ;NO ATTRACTORS FOR COHO ;NO ATTRACTORS FOR COHO ;NO ATTRACTORS FOR COHO ; If you are trolling in an area that you are reasonably sure there areCoho, a simple method may help get multiple hook-ups. When you have located a school of Coho,

    This is called the Ace In The Hole setup, again possibly not to scale

    Page 6 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    7/17

    or even Chinook, abandon your flasher, etc. Simply use a 4 oz. slider sinker and a moochingleader. Instead of stacking running more rods than you really want on the downrigger, run say oneeach on your downrigger & simply troll the others. For the ones on your downrigger, snap yourrelease on the mainline below the sinker & the bait as far as you prefer. Now when you get a hit,raise or lower the downrigger wire to the depth of the hit, pop off the release on the other rod, pullthe wires up, & kick your motor into neutral & you are very quickly mooching, hopefully in theschool of fish. You may want to either raise or lower your other lines to put them into the "FishZone". Many times this is more effective than trolling thru the school.

    Also, at this time, if the frenzy is on, do not get real excited in bringing in all the fish to the netbefore you rebait & get the bait back in the water, as the thrashing fish seem to attract others tothe area.

    Another method somewhat akin to the above, is to run the 6' mooching leader behind a rudder.Snap the main line into your downrigger release with 80-90' of line behind the release. Youshould be able to see the downrigger ball on the screen, now by watching the sonar fishfinderconstantly, & then when you see a fish arch above or below the ball, immediately raise or lower theball to match the fish's depth. Your bait will have enough time to move to the depth you have nowset the ball by the time you have trolled to where you saw the fish. Sometimes this method oftargeting a single fish will pay off better than "Flock Shooting" the whole ocean in hopes ofstumbling onto a fish at the right location & depth.

    SNUBBERS ;SNUBBERS ;SNUBBERS ;SNUBBERS ; Since the requirement of barbless hooks, it has been apparent that many fish arehooked, but come off before being brought to the boat. Les Davis has now come out with a 10"rubber snubber that is attached in the system, either between the mainline end and the flasher orbehind the flasher. This will help maintain a more constant tension on the fish, and possibly helpprevent the hook from pulling out.

    My thoughts here is that it does 2 things. IF you are using the new "Spectra" type braided lines &a stiff or fast rod, yes you WILL need a snubber to make up for the solid connection to the fish.However if you are still using monofilament line, the line has enough stretch in it to do the same asa snubber.

    There is a couple of alternatives that will improve your catching ratio. You can use the braidedline, but keep the drag set to just where it does not pull off the reel when trolling, put the clicker.When you get the pop off, let your loose drag peel line when you hook up. Do this until the fish iswell behind the boat. Make sure the drag is loose. Reel down on the fish to the point where thebend of the rod starts showing a definite hooked fish on it, but resist the temptation to set the

    hook. The speed of the troll, the bend of the rod, the setting of the drag, the sharp hooks, and thesnubber should be enough to do the job.

    MATCH THE HATCHMATCH THE HATCHMATCH THE HATCHMATCH THE HATCH ;If using a squid or spoon, try to use a size & color of the baitfish in the areaon that particular day. As soon as you catch a fish, cut it open & examine the stomach contents.This will give you a clue as to what bait is in the area.

    As Tom Nelson form Salmon University says about artificial bait,"any color as long as it isgreen". And if you fish below about 30', it is best to use a GLO version of spoon or squid. Tomalso suggests a blue/green/cream glo squid with a small green Spi-N-Glo on the line in front of it20"- 32" behind a Hot Spot flasher. This system has also proven itself behind a diver.

    SCENT ;SCENT ;SCENT ;SCENT ; Use scent on all artificial baits, herring. anchovy, scrimp, seem to be the best. Put PowerBait & /or scent into a squid body.When using scent, try not to get it on the mainline at the location of the downrigger release, this

    makes for more premature tripped releases. One other approach is when using a snubber, punch acouple small holes in the rear, & inject the hollow tubing with scent, this then acts as a reservoir &slowly releases the scent over a longer period of time.

    While on the subject of scent, many people excrete a enzyme that fish find repugnant. There isquite a bit of evidence that L-lysine from human hands repels fish. People have different levels ofthis amino acid in their bodies, which is excreted onto their hands, and it is easily transferred tolures and bait. To be on the safe side, before you start to fish, wash your hands with a fishingtype soap, or dishwashing soap (Lemon Joy), dry them, & then place a small amount of herring oilon them, rubbing it into your skin. Pat your hands dry with a towel, without wiping it off. This will

    help set things up for a possible catching experience, as there is a difference between Fishing&Catching.

    Page 7 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    8/17

    While on this & relating back to SMELL There is a new item on the market & brought out by SalmonUniversitythat is called the "Salmon Scenter". This was a specially designed PVC tube with slots inthe sides that is filled with their scent nuggets & then attached to the downrigger ball. Inessence, it milks out a scent trail & with your flasher/bait in this trail, it increases the percentageof strikes. The scent nuggets are the same fish food that the hatcheries feed the small fish beforereleasing them. This appears to work best for hatchery Coho, as it gives them something familiarto home in on, & targets the fin clipped hatchery fish as opposed to "Wild Coho" that usually haveto be released.

    This original design has now become obsolete & has been replaced by a nylon mesh bag pre-filledwith the nuggets & sold by Silver Horde.

    RELEASE CLIPS;RELEASE CLIPS;RELEASE CLIPS;RELEASE CLIPS;When using downriggers you will have to use some sort of line releases. Thereare about as many different types of these as you can imagine, you will have to pick one with theproper tension for the fish being targeted, as a light one for trout will not hold the salmon flasher.The most common use spring tensioned pads to hold the line, for a lighter trip off you set the linefarther out in the gripping pad area. When going thru weeds, the weeds sometimes foul therelease, not allowing it to trip. It is recommended that if you find weeds in the area to pull thegear more often to clean it. The new Scotty release is designed to divert weeds off of it betterthan most.

    When using the new spectra lines, some spring padded type releases do not really hold the linewell, or cause abrasion & can break the line off. The best release found for these are the Pro

    Release, which uses a pivoting arm that snaps into adjustable rubber notches. The one thing toremember here is that be careful when winding the line on the arm so that it does not overlap, &thereby not releasing when tripped. This one does have one disadvantage, in that since the line iswound around the pin with the trailing part farther out on this piveted pin, that if you try tomanually trip it, sometimes it is hard to trip.

    On all releases it has been found best to use one that has a heavy mono attached to the largesnap that has enough length so that you can snap it onto the wire & without having to lean outover the boat's gunnel to attach the release to the fishing line. This will also allow you to attach iton the line more precisely each time. The most common length seems to be about 48".

    The one possible drawback for using a heavier release setting is that possibly a undersize fishwill not trip the release as reliably. You will have to balance the release setting to the actualamount of drag encountered by your gear. It seems best to use a setting that when you winddown the rod's line, to create the rod arch after achieving your depth, that occasionally you willhave it trip off without a fish. This will be apparent within seconds after getting it set.

    Another thing to remember is that if you are stacking 2 lines on one wire, that they both willhave to be set to a slightly higher trip tension, so that you don't have to be constantly bringing the

    Release clips, Offshore top left, Pro Release bottom left,new Scotty top right, with older Scotty below & old Scotty

    plunger type bottom middle

    Page 8 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    9/17

    wire up & reattaching the release if one trips off prematurely.

    HOW LONG A RELEASE?HOW LONG A RELEASE?HOW LONG A RELEASE?HOW LONG A RELEASE? ;This pertains to the length of the heavy (100#) mono that attaches therelease to the wire clip. The longer the downrigger boom, the longer the release line has to be. Ithas to be at least as long as your boom, otherwise you will be leaning dangerously over the gunnelto attach the line to the clip. I usually use a 48" length. One thing you can do if it pops off & youhave pulled the wire in, but the release is trailing in the water too far out to grab, is to reach outwith your rod tip & pick it up, then bring it in to where you can get ahold of it from there.

    HOW FAR BACK?HOW FAR BACK?HOW FAR BACK?HOW FAR BACK? ;This is sometimes called DROP BACK, & is in reference to how far back do youlet the flasher go before snapping the release onto the line. It will depend on the water clarity, thefish targeted, the visibility of your line, etc, etc,. Some fishermen run the gear back 40', whileothers go back 10'. Remember however, that the farther back you go, the less setting power therod has when the release is tripped. I seem to have settled on about 15' for most saltwatersalmon fishing, but am experimenting with closer. Some of these lengths are what is required toallow the attractor to operate properly. Also if you are relying on a "Black Box", your electricalcharge on the wire decreases as you go farther back. Here are Tom Nelson's recommendedlengths.

    Large Metal Flashers ---- 6 to 10' Large Plastic Flashers ---- 8to 15'

    Small Metal Flashers ---- 8 to 12' Small Plastic Flashers ----10 to 20'

    DOWNRIGGER WEIGHTS ;DOWNRIGGER WEIGHTS ;DOWNRIGGER WEIGHTS ;DOWNRIGGER WEIGHTS ;Most weights, (balls) used for salmon fishing will be from 10 to 15#,with 12# being the most common. If you use the heavier weight you can get deeper with less blowback, & have less chance of line tangle between the rigging on both sides. Also the plus here is ithelps keep the wire more straight in the water & lessening the chance of a tangle around theprop. Some electric units however are not strong enough to pull a 15# ball.

    Some weights have a metal fin off the rear that can be bent to allow the ball to track in onedirection more than just straight back. This can be helpful if you bend them so they tend to directthe wires more outward.

    Ideally the ball should be painted or plastic covered to help with the conducting of electricity in apolarity problem. If the ball is not coated, then the next best thing is to use a ball connector ofsome type on the end of the wire that is made of a non-conductive material, (nylon, plastic, leatheretc.). In use you need something to attach between the ball & the terminal end of the wire. Scotty

    & Silver Horde make these about 12" long & out of a plastic that will stretch. They say it acts as ashock cord also. You can make your own out of 150# Tuna cord for a lot less. This will beak theconductivity to the wire, & at the same time give you something to hang onto when you may wantto pull the ball into the boat without trying to hang onto the wire itself.

    BLOW BACK ;BLOW BACK ;BLOW BACK ;BLOW BACK ;Your trolling speed & current will make a difference here, usually you want yourdownrigger line angle to be about 45 degrees no matter what actual speed you are traveling. Thisequates to 143' of line out to reach 100' of water depth. If you are out farther than this angle, youcan not reach the depth you intend to. The problem comes in if you are trying to reach say 200',the wire angle would equal 286', but your line drag may increase this length even more. You willhave a belly in your fish line from where it enters the water to your release clip so much that therod action will not set the hook like it is supposed to do if fishing shallower. And if the line isstraight up & down, you are not moving at all. Most downrigger wire is only 250' long.

    TROLL WITH THE CURRENTTROLL WITH THE CURRENTTROLL WITH THE CURRENTTROLL WITH THE CURRENT ;The fish will be swimming into the current, if you troll with thecurrent, the fish will see it coming, instead of it sneaking up behind them, & you will also covermore water. Also it allows the fish less time to scrutinize your lure, possibly bringing on a strike,where if the fish has more time it may realize the lure is just that & not something to be eaten.Depending on the flow, you may only be sitting in the same position with water passing underyou.

    TROLLING SPEED ;TROLLING SPEED ;TROLLING SPEED ;TROLLING SPEED ; The most important thing is to have your flasher & bait working properly, asthey were designed to do. The old story is troll slow for Chinook & fast for Coho. That may havebeen so with the lures & gear of that day, but now things are slightly changed. Take a look at thecommercial salmon troller, many times he will be doing 6 mph. The knowledgeable fishermencurrently say most fishermen now troll too slow. What ever bait you are pulling, or

    Page 9 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    10/17

    flasher/dodger, you will have to look at it in the water & decide how it is functioning, then adjustyour speed from there.

    PULLING IN YOUR LINE ; PULLING IN YOUR LINE ; PULLING IN YOUR LINE ; PULLING IN YOUR LINE ; If you have to pull your line in to change gear or a missed hit & it did notpop off, don't try to trip it off the clip with the rod. Raise it by bringing up the downrigger wire.The reason is threefold. First, this is probably the most likely way to break a rod. Second, someclips do not trip as easily from the rod side as compared to from the lure side. And third, if the lureis even somewhat working, it may catch a fish on the upward trip.

    WATER TEMPERATURE ;WATER TEMPERATURE ;WATER TEMPERATURE ;WATER TEMPERATURE ; Fish will try to stay in a water temperature that they find comfortable tothem. This may explain why some fish stay nearer the bottom than others, because the water willbe warmer on the upper layers.

    This may be way more important on the estuary Chinook salmon fishing like Buoy 10. Usually atthe time the season opens here there has been no rains for a couple of months & the river's watertemperature may be 72 degrees. With the water this warm as compared to 56-58 degree of theocean water the fish have just come from, the fish will move in & out with the tide. The estuary'swater temperature will be between 56 & 65 degrees depending on the tide, because of the mix ofocean water to the warmer river water. However the bulk of the fish seem to not stay in the lowerriver. The ones that do, will try to locate a hole that will have cooler water.

    You may have heard that the fish lay off the mouths of the rivers waiting for fresh water of arain, yes, this may be true, but I think it also could be that the new rainwater is also cooler.

    If there is no rain, then when the fish have matured to the point that they have to go upriver,

    they do not stay in any one location for any period of time, just let me go back home.One thing you may consider is to get a fish thermometer and occasionally attach it to your

    trolling cannonball. This will read temperature at where you are fishing. Otherwise thetemperature taken off your depth-finder sensor will only read the water surface temperature.

    SEAWEED ;SEAWEED ;SEAWEED ;SEAWEED ; Seaweed can get enough on the line to foul the swivels & therefore create twistedgear. If troubled with seaweed or grass on your line, adding a golf tee on the mainline as youruppermost gear, will help divert most weeds off. The tapered small portion of this golf tee seemsto allow the weeds to be passed off, where a knot at a swivel seems to stop & hold the weeds.

    JELLYFISH ; JELLYFISH ; JELLYFISH ; JELLYFISH ; At times these critters can make life miserable. If they are on your gear, it is verylikely salmon will not be interested. Also when you pull the gear in & remove these jellyfish, theyhave a composition in their bodies that feels like nettle stings. One word of caution, WAS YOURHANDS before you go to the toilet facilities. One fisherman shared his method of removing this

    jelly off his hands, by use rubbing alcohol.

    LEADERS & HOOK SIZE ;LEADERS & HOOK SIZE ;LEADERS & HOOK SIZE ;LEADERS & HOOK SIZE ;Terminal leaders, 20#, 2/0 - 3/0 solids for cut plugging for early Blackmouth, Feb- JulyTerminal leaders, 20#, 3/0 - 4/0 solids for cut plugging for later Blackmouth & ChinookTerminal leaders, 20#, 3/0 - 4/0 slips when using frozen bait in bonnetTerminal leaders, 25# / 40#, 4/0 - 5/0 solids, tied close, for large bait in Estuary use (largeChinook)Terminal leaders, 40# / 70#, 5/0 - 5/0 or even 6/0 -6/0 solids, tied close for use with squidbehind flashers

    Tie terminal leaders 2 lengths,(1) 36", rolled onto pipe insulation for faster attaching (you will use more of this size & it savesleader)(2) 72 " " " " " " " (you usually will find these as the std.commercially tied)

    Primary leader 36" with black swivels, for behind sinker or attracter, make up the desired OAL withterminal leader

    LEADER LENGTHS FOR REGULAR TROLLING,LEADER LENGTHS FOR REGULAR TROLLING,LEADER LENGTHS FOR REGULAR TROLLING,LEADER LENGTHS FOR REGULAR TROLLING, (Estuary rig) bait 36" - 72" " " " MOOCHINGMOOCHINGMOOCHINGMOOCHING (Most Saltwater) bait 72"

    While we are on this subject, it has been found that it may be best to NOT tie your leaders on limpmonofilament. The reason seems to be that with the spinning action of the bait, even if you useswivels between the sinker or attracter, that the limp leader just doesn't have the ability to resistthe twisting action of the bait up the line to where the swivel can do it's job.

    Page 10 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    11/17

  • 8/9/2019 Http Www.pugetsoundanglers

    12/17

  • 8/9/2019 Http Www.pugetsoundanglers

    13/17

    Squid or Hoochies -- here it has proven advantageous if you, when running a squid behind aflasher/ dodger, (not a Fish Flash) to add approximately a #4 green or blue Spin-N-Glo on theleader ahead of the plastic squid, using a plastic bead between the tow as a bearing. This will addto the attractiveness of the lure.

    2 LURES ON ONE LINE2 LURES ON ONE LINE2 LURES ON ONE LINE2 LURES ON ONE LINE;If you look on Scotty's webpage, www.scottyusa.com they show how to run 2lures off one rod line using a downrigger. Basically you attach the lure like you normally do, butthen let it down about another 15 ft or so, attach another release clip, (this one should be short

    from the wire to the release). Pull slack so there will be a belly in your line when in motion, snapanother lure onto your rod's line between these release. This 2nd lure (preferably a spoon, etc.and on a shorter leader to help avoid tangles) will find it's way to the center of the belly & ridethere. You will now have to be alert, and when pulling the ball, to not put a electric downrigger onautomatic & forget to stop it short & remove the top release. You will also have to use extra carewhen netting a fish caught on the top lure.

    This principle can also be used in mooching or diver trolling fishing, if you make the 2nd leadershort (20") and attach it to a swivel placed in the line about 40" above the lines terminal end.

    THE HOOK ;THE HOOK ;THE HOOK ;THE HOOK ;Buy the best hooks you can afford. It makes little sense to pay a small fortune for aboat and then scrimp a few bucks on the one thing that is the most important of all.Rule #2. Sharp Hooks. This seems like an obvious thing but most fishermen ignore it. Very fewsalmon hooks are sharp enough even brand new. The Scotty Pro team worked eight years filmingsalmon hitting baits and lures in the ocean. They learned that the salmon come after your bait time

    and time again. The average salmon misses or just grazes the bait at least two times before hehits solid enough to get hooked. They observed one salmon hitting a bait twenty two times beforehe got hooked on the twenty third try. If your hooks are sticky sharp you have a much betterchance of that hook digging in as a salmon hits and slashes at the bait.You will find fishermen swear by as many different brands of hooks as is out there on the market.They will all catch fish, some seem to be better than others. The important thing is to keep themSHARP. I test the hooks tip by scratching my thumbnail, if it digs in it is sharp, if it slides across,sharpen it. During fishing season, my thumbnails look pretty chewed up. Carry a hook file oremery stone and sharpen those hooks on every trip. Recheck them occasionally. You willdefinitely be rewarded with more salmon in the fish box.

    Take your pliers and bend the hook out and away some from the shank so as to offset it a littlemore. Next SHARPEN your hooks from the inside edge so as to direct the point slightly out and notin as the come from the package.

    MATCH THE HOOK TO THE BAIT SIZE ;MATCH THE HOOK TO THE BAIT SIZE ;MATCH THE HOOK TO THE BAIT SIZE ;MATCH THE HOOK TO THE BAIT SIZE ;

    When using bait, you should generally match your hook size to the herring size for

    best results.

    CUTTING & HOOKING BAIT ;CUTTING & HOOKING BAIT ;CUTTING & HOOKING BAIT ;CUTTING & HOOKING BAIT ;When cut-plugging a herring, you should wet your hands, cuttingboard, herring etc. This will promote the non removal of scales off the bait. The more scales youleave intact on the bait the better the bait will perform for you. In cutting the bait, if you do notuse a cutting guide, use the 45/45 degree rule. Then remove the entrals. One modification is toalso cut a 90 degree Vee notch at the rear of the body cavity. This generates longer bait life by nottearing the cut angle & allows the water to flow out this hole, creating bubbles. A modified WestPort hook up is good. This is hooking the upper hook thru the belly cavity & up thru the backbone& out in the center of the back. The other hook is passed thru the belly cavity & out the short side

    HERRINGSIZE

    PACKAGE LABEL COLORAPPROXIMATEHOOK SIZE

    3-4" Orange label 1/0 - 2/0

    4-5" Red label 2/0 - 3/0

    5-6" Green label 3/0 - 4/0

    7-8" Blue label 4/0 - 5/0

    8-9" Purple label 5/0 - 6/0

    9-14" Black label (horse herring) 5/0 - 6/0

    Page 13 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    14/17

    belly, then just allowed to dangle back by the tail.

    When using whole herring for bait, about the best way I have found is to run the rear hook thru thelips of the herring sideways. Hold the herring by slightly squeezing it on top of the head & bottomof the jaw. Right behind the forward part of the lip juncture between the top & bottom you willfind a spot that the upper hook will go straight thru from one side & out the other, push it thru.With the lower hook on the same side that the upper hook's eye is on, push it into the rear sectionof the herring, (usually about 3/4 of the way back). Bring this lower hook mostly thru the bait &

    back out so that the hook's point is facing forward with the eye laying alongside the bait. Nowrotate the front hook 180 degrees without tearing the bait, & push it in thru the rear gill plates &out the other side so both hooks points are on the same side. There should be a slight bendbecause of the tension from the front hook. If the bend goes not give the desired spin, move therear hook either forward or rearward or tie your leader spacing differently to match the bait size.The above method holds the mouth closed.

    Another method is to use one of the "herring bonnets" when you troll whole herring. There aremany different types, but essentially they allow you to put the nose of the bait in a protectedbonnet. This will help especially if the frozen bait is not as good as you may like, & it helps keepthe bait from pulling apart, & gives a rotating turn to the bait, without the effort of placing thehooks EXCACTLY in the right location for each bait.

    TO TOUGHEN YOUR BAIT ;TO TOUGHEN YOUR BAIT ;TO TOUGHEN YOUR BAIT ;TO TOUGHEN YOUR BAIT ;To toughen herring or anchovy bait, soak in 1 cup rock salt to 1 quartwater, to form a salt brine, bait should be soaked in this overnight, however even a few hourshelps. It can be kept in a refrigerator for a a month or so, if for longer freeze it in the brine. Thebrine being a strong salt solution will not freeze. You however may want to make a wooden floaterlid on your container to keep the bait submerged.

    Formula #1 put blue & or green food coloring in brine to replace dead fish color.Formula #2 add powdered milk into the brine. This powdered milk being lactic acid, kind of actslike a tanic acid & sets the scales.Formula #3 combine 1 & 2

    SINKER DROPPER LENGTH, REGULAR TROLLINGSINKER DROPPER LENGTH, REGULAR TROLLINGSINKER DROPPER LENGTH, REGULAR TROLLINGSINKER DROPPER LENGTH, REGULAR TROLLINGEstuary (Shallow water) (15) 12"" " " " " (Deeper

    water) (35+) 24"This rig consists of a sturgeon sinker slider unit on the mainline. Attach a lighter dropper to theslider for the cannon ball sinker.

    Attach a Fish Flash to the mainline, with the bait tied to the Flash. Use a large Fish Flash as thewater is usually not clear.Here is surely a time to slide a golf tee on the mainlines uppermost section above the sinker sliderto keep off the weeds.

    SINKERS forSINKERS forSINKERS forSINKERS for MOOCHING ;MOOCHING ;MOOCHING ;MOOCHING ;Since the barbless hook requirement, the old tied in line kidney sinkershould be abandoned, because it can be used as leverage for the salmon to throw the hook. It issuggested that it be replaced be the Metzler slider bar type sinker, or the simple sturgeon sinkerslider on the mainline and then attach the round cannon ball sinker to this slider snap. The roundball is cheaper & has less resistance so therefore a lighter sinker will get you down just as deep.Another good thing to do when using the slider, is that the cheap snaps usually used on thesesliders will bend if you get the sinker hung up. Or you can use a lighter short 6" leader as adropper, thereby breaking the dropper and saving your other gear.

    WASHINGTON 2 OUNCE LIMIT ;WASHINGTON 2 OUNCE LIMIT ;WASHINGTON 2 OUNCE LIMIT ;WASHINGTON 2 OUNCE LIMIT ;To fish deeper if in a Washington State 2 oz weight restrictionareas, if you are using standard gear, switch to a 20# spectra type line. This is usually equal indiameter to 6# mono for size & will create less drag. The word is that using this gear, watching thetide change & back-troll. Buy using this method, 150' depths can be achieved with a 2 oz weight.Or use the super-line and a diver that weighs less than the 2 oz. Doel Fins & Luhr Jensen Jet Diversare 2 that do comply, and can get down to about 50 ft. Rig the Jet Divers on an 18" dropper off theend of the mainline 3 way swivel. Then off the 3-way swivel go with 40" to 50" of leader to a smallHot Spot Flasher or Fish Flash, then 20" to 24" leader to a squid or herring for Coho, or 26" to 31"for Chinook.

    POLARITYPOLARITYPOLARITYPOLARITY; Commercial trollers have for years known that some boats will out-fish others, thiscan sometimes be traced to electrical current in the downrigger wire. If you remember your

    Page 14 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    15/17

    chemistry from high school, when you place 2 dissimilar objects (stainless wire & zinc anode or aaluminum boat) in a conductive solution (salt water) you create an electrical charge. Scotty & ProTroll both make a "Black Box" that can be adjusted to give the desired electrical charge to yourwire. Different types of fish react to different electrical charges. If you have any doubts, you cansimply check your wire with a volt/amp meter. It should have a voltage of + .5 to +.7 from yourground to the downrigger wire. If it is outside this range either way, it will benefit you to considerdoing something to correct the problem. If the voltage is low, you can add zincs to yourmotor/trim tabs, etc. If it is high, then it is suggested you check things out & ground everythingmetal that is in the water. One thing most overlooked would be your trim tabs. They will usuallybe bolted thru the fiberglas hull, just run a bare #10 wire as a ground from you negative batteryterminal to the bolts & put a second nut holding this ground wire. Do this to anything metal thatis on the outside of the hull.

    PROTECTING YOUR GEAR ;PROTECTING YOUR GEAR ;PROTECTING YOUR GEAR ;PROTECTING YOUR GEAR ;The saltwater environment is something that will ruin more gear thananything else. Many fishermen don't properly take care of the rods, reels, flashers, or spoons. Theresult is when they want to use them next year, many are ruined or badly in need of TLC. Onemethod commonly used by knowledgeable persons is to, as soon as you get off the water, or atleast before you leave the boat for the night, spray the gear with "Salt Away". This solution willremove the salt. Next you want to lightly wash the same gear with plain water. Let it dry, andthen spray it with a corrosion blocker. Two that are effective & economical are made by CRC. Theycome in aerosol cans & are CRC "3-36" & CRC "Engine Stor". Another would be LPS-1. This stuffis a light spray metal protector & will help immensely on rod guides, reels, swivels & spoons.

    WHAT TO DO AFTER YOU HOOK A FISHWHAT TO DO AFTER YOU HOOK A FISHWHAT TO DO AFTER YOU HOOK A FISHWHAT TO DO AFTER YOU HOOK A FISH; In use you can set the drag slightly lighter than normal,but to where it does not pull off while the boat is moving. Set the clicker to "ON", this will wakeyou up when a fish hits, & with the drag set slightly lighter, if the fish happens to be large enoughto pull the line until you get things organized.

    OK, now your rod has "Went Off", meaning a fish probably has hit the lure & the line has snappedout of the line release. What do I do? Grab the rod & REEL FAST to take any slack in the line & seeif you can feel the fish on the other end of the line. If it is still hooked & you can feel it, reel in &keep the line tight.

    Once you make a decision as to the size of the fish, do we leave your partners rod in the water ornot. If the fish is under about15#, you may leave the other rod out hoping to pick up another outof a possible school of fish. Do not stop the motor, but keep trolling & you may want to turn the

    boat SLIGHTLY toward the fish to give more room to net the fish, while at the same timeconsidering keeping the other lines from tangling in the prop. You may slow down slightly, but donot stop. For one, if you do stop, then your partner's line may become entangled with hisdownrigger wire.

    As soon as the fish hits, pull that downrigger wire & ball in. Here is where the electric downriggercomes in handy. If you are using a electric model that has an automatic button & a preset shut-offtrip, all the better. Pull the ball into the boat. You may also want to rotate the downrigger armstraight back or forward to give more room off the side to net the fish, without entangling things.

    If the fish is a larger fish & pulling out line that you have no control over, then you had betterquickly pull the other downrigger up, stow the balls & be ready to fight the fish, or even chase it torecover some line back onto the reel spool.

    It is best if the netter & the fisher to also wear Polaroid glasses, this will allow them to see into thewater & see the fish a lot better cutting out the surface glare.

    Another thing to keep in mind, is at all costs try to keep the fish out of the other downrigger wire.If it happens to tangle your partners line, then have him put his reel in free-spool, only reeling inwhen lots of his line is out, but not interfering with the fighting of the fish.

    Most experienced recreational trollers do not stop the boat when an average size fish hits, as thereis usually other gear out. By the time you realize it is a fish large enough that you may have to pullthe other gear & chase it, this fish may already have 150 yards of line out & going away from you.You need a reel that has enough line capacity to act as a cushion to allow you to get the other gearin, turn around & chase the fish to retrieve some of this lost line.

    Page 15 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    16/17

    Some fish, depending on where they are hooked will ant to go to the right, or the left. Take him onthe side he wants to go to, do not to to bring a RH hooked fish on the LH side of the boat. If a fishis hooked with a lure on one side of the mouth & you keep putting him on the other side justbecause that is where you are comfortable in netting from, you very well may pull the hook outbefore he comes in. This then will also determine what you will do with the other rod &downrigger wire.

    This has also proven beneficial if you happen to have 2 fish on at once, as with the boat still

    moving, the second fish tends to not get as excited if you do not get it really close (around 30') tothe boat & it will tag a long, giving you time to net the other smaller or more tired fish first.

    NETTING THE FISH ;NETTING THE FISH ;NETTING THE FISH ;NETTING THE FISH ; Wear poloroid sunglasses to help cut the water surface glare & allow you tosee the fish in the water better. More fish are lost within 10' of a boat than any other location byfishermen who try to net too soon.

    OK, the fish is coming in, ( we are now assuming that you are not alone here.) If possible let thefish tire out to the point that it comes in along side of the boat, without spooking & wanting tomake another run. Some skippers like to have the fisherperson move forward enough from thestern to allow the netter to stand in one of the rear corners. This gives the netter a chance to covermore area if the fish tends to go behind & or under the motors.

    The netter needs to grab ahold of the BOTTOMof the net bag lightly with a couple of fingers of theforward hand that is also holding the net handle close behind the bow to give maximum diversity.This method is so that you are holding the bag out of the water & not spooking the fish. With theother hand the netter has ahold of the handle as far back as possible & yet be able to control thenet in any circumstance.

    Be sure that the reel drag hasNOT been tightened down more than normal during the fight, as ifthe fish makes another run with a tight drag, it may pull the hooks out or break the line or rod. If

    it is a large fish you may even lighten the drag slightly to assure this will not happen. Allow thedrag do what it is designed to do. This will actually get more fish into the boat. When the fishcomes along side & appears to not offer a lot of resistance, the fisherperson needs to lead the fishtoward the netter, but not bring it's head out of the water, (for some reason the fish finds extraenergy if it's head is out of the water.) As the fish is lead in, the netter makes a QUICK jab downIMMEDIATELY IN FRONT of the fish, at the same time releasing the fingers that are holding thebag's bottom at the same time the net hits the water & since fish has not reverse, the net can thenbe QUICKLY lifted straight up, closing the bag & trapping the fish in the net & then against the sideof the boat. Do NOT raise the net parallel with the water, but pick the handle straight UP, againclosing the bag.

    Also here is one thing to remember, that IF the lure has more than 1 hook, when you net the fish,

    Notice the left 2nd finger of the forward handholding the net bag. Also notice the Polaroid

    sunglassesNice job on a 26# Chinook salmon

    Page 16 of 17Puget Sound Anglers State Board

    8/5/2010http://www.pugetsoundanglers.org/fishing/Downrigger_salmontrolling.htm

  • 8/9/2019 Http Www.pugetsoundanglers

    17/17

    you have to do it right the first time, as if you do a close miss but are near enough to tangle a loosehook in the net, you can kiss the fish goodbye because the fish is now probably outside the bag &yet attached to it.

    Sometimes this process has to be speeded up if you can see that the hook is lightly hooked in theedge of the fish's mouth, & you run a chance of having it pull out at any second. Try to bring in &make a quick shot at netting. Do not try to net a fish that is deeper than VERY CLOSE to the top &remember that these fish have no reverse, but they can turn very quickly.

    As soon as the netter has the fish in the net, strip of 6 feet or so of line so the rod tip will have abetter chance of survival during the excitement when the net & fish are brought into the boat.

    RELEASING A FISH ;RELEASING A FISH ;RELEASING A FISH ;RELEASING A FISH ;If your fish is one that the regulations say is illegal, in that is is not adipoisefin clipped, then you will have to release it unharmed without taking it out of the water. In thiscase you should not tire the fish unduly, but get it in as fast as possible to ensure that it has a goodsurvival. There are a couple of ways to go here. A hook release can be used. This is like a smallgaff hook with no sharp point on the end. In use, when the fish is close to the boat & tired enoughthat you can grasp the leader a foot or so from the fish, use this hook remover by reaching out &hooking the line. Next bring the remover close to the fish, & with the other hand holding theleader, quickly raise the hook remover handle while at the same time lowering the hand holdingthe leader. What this does is raises the fish's head into the remover, but reversing the hook &putting the weight of the fish to unhook itself.

    Depending on the size & specie of the fish, & whether it is tangled in the leader, you may have tonet it, but keep it in the net tight against the side of the boat. Unhook it & tip it out of the bagwithout bringing it aboard. For a link to an article on releasing fish CLICK HERE.

    DOWNRIGGER WIRE AROUND THE PROP ;DOWNRIGGER WIRE AROUND THE PROP ;DOWNRIGGER WIRE AROUND THE PROP ;DOWNRIGGER WIRE AROUND THE PROP ; Needless to say this is to be avoided if at all possible.For those of you who use the main motor for trolling at times, I recommend the "Sting Ray" typestabilizer fin that is attached to the cavitation plate. Your boat / engine may not need it'sadvertised usage of "getting out of the hole faster", but let me tell you, these fins sure makesomething for you to lay on when the motor is tipped up & to have something to hang onto whilesomeone else hangs onto your feet while you unwind the wire off the prop. Especially when youare 15 miles out in the Pacific Ocean & it is rather choppy. You may say it won't happen to me, butif you fish with downriggers enough the odds are against you. Also carry a spare spool of wire,crimpers, sleeves & an extra weights.

    If you run the spectra type lines & get that around the prop shaft, you will very likely be in forproblems of tit cutting the shaft seals out if allowed to run even for a very short time.

    Compiled by LeeRoy Wisner. Some of the above information has been gleaned from many sources,and 50 years of personal salmon fishing, with special thanks to John Keizer, Tom Nelson, TomPollack & Dick Pool.

    This started out as simply a leader length behind flashers list, but seems to have grown into a general salmon trolling page.

    Copyright 2004-2005 LeeRoy Wisner All Rights Reserved

    Originated sometime 1997, Last modified 12-30-2005

    to contact the author click here

    HomeAbout UsFishingPoliticsConservationPhotosContact Us

    Page 17 of 17Puget Sound Anglers State Board