3gpp ts 36.212, 'multiplexing and channel coding'...the sat-ofdm is a satellite radio...

T T

A S

t a n

d a

r d

정보통신단체표준(영문표준)

TTAE.3G-SAT.36.212 제정일: 2013 년 xx 월 xx 일

IMT-Advanced SAT-OFDM – 다중화

및 채널 부호화

IMT- Advanced SAT-OFDM - Multiplexing and

channel coding

(Release 1 – Compatible with 3GPP Release 8)


TTAE.3G-SAT.36.212 제정일 : 2013 년 xx 월 xx 일

IMT-Advanced SAT-OFDM – 물리채널 및 변조

IMT-Advanced SAT-OFDM – Multiplexing and channel

coding


본 문서에 대한 저작권은 TTA 에 있으며, TTA 와 사전 협의 없이 이 문서의 전체 또는

일부를 상업적 목적으로 복제 또는 배포해서는 안 됩니다.

Copyrightⓒ Telecommunications Technology Association 2013. All Rights Reserved.


i TTAE.3G-SAT.36.212

서 문

1. 표준의 목적

본 표준은 위성 IMT-2000 Direct Spread 방식 기반의 시스템 개발 시 무선전송기술 중

물리계층 (Physical Layer)에 관한 기술을 정의한 표준으로서 ITU-R 의 국제규격 및 3GPP

표준에 근거하여 국내 표준을 제정함을 목적으로 한다.

2. 주요 내용 요약

여러 개의 전송 채널은 다중화 되어 하나의 물리 채널로 전송될 수 있다. 지상 IMT

OFDM 방식 기반의 시스템인 3GPP LTE 및 LTE-Advanced 와 호환성을 가지는 위성 IMT-

Advanced SAT-OFDM 시스템의 전송 채널이 물리 채널에 매핑 될 때까지의 각 과정 (CRC,

coding, Rate matching, insertion of DTC, interleaving, multiplexing 등)들에 대해

설명한다.

3. 표준 적용 산업 분야 및 산업에 미치는 영향

TTAE.3G-SAT.36.212 은 전송 채널이 물리 채널에 구현되는 과정에 대해 정의한다. 즉,

여러 전송 채널이 다중화되어 물리 채널로 매핑 되는 과정을 표준화한다. 다중화와 코딩에

대한 통일된 규격으로 단말기 및 기지국간 이 기종간의 호환성을 보장해준다. 본 표준은 4G

개인 휴대형 위성이동통신 분야에 적용가능하며, 위성을 이용하여 육해공 어디서나

seamless 서비스 제공이 가능하도록 한다.

4. 참조 표준(권고)

4.1. 국외 표준(권고)

- LTE TS 36.212 – Multiplexing and channel coding (Release 8) (v.8.8.0)


ii TTAE.3G-SAT.36.212

4.2. 국내 표준

- TTAT.3G-36.212 – IMT-2000 3GPP – 진화된 UTRA – 부호화 및 다중화 (Release 8)

(v.8.6.0)

5. 참조표준(권고)과의 비교

- 해당 사항 없음

5.1. 참조표준(권고)과의 관련성

기술 규격 TTAT.3G-36.211 및 3GPP LTE TS 36.211 은 지상 IMT OFDM 방식 기반의

시스템인 3GPP LTE 및 LTE-Advanced 의 물리계층 다중화 및 채널 부호화를 표준화하고

있다. 본 표준안은 SAT-OFDM 이 3GPP LTE FDD 와 공통성을 가지지 않는 부분의 내용

수정을 제외하고 LTE TS 36.212 의 내용과 동일하다.

5.2. 참조한 표준(권고)과 본 표준의 비교표

TTAE.3G-SAT.36.212 LTE TS 36.212 비고

1. 표준의 구성 및 범위 1. 표준의 구성 및 범위 내용수정

2. 참조 2. 참조 내용수정

3. 용어 정의 및 약어 3. 용어 정의 및 약어 내용수정

4. 물리채널 매핑 4. 물리채널 매핑 동일

5. 채널 부호, 다중화,

인터리빙

5. 채널 부호, 다중화, 인터리빙 내용수정

6. 지적재산권 관련사항

본 표준의 ‘지적 재산권 확약서’ 제출 현황은 TTA 웹사이트에서 확인할 수 있다.

※본 표준을 이용하는 자는 이용함에 있어 지적 재산권이 포함되어 있을 수

있으므로, 확인 후 이용한다.

※본 표준과 관련하여 접수된 확약서 이외에도 지적 재산권이 존재할 수 있다


iii TTAE.3G-SAT.36.212

7. 시험 인증 관련 사항

7.1. 시험 인증 대상 여부


7.2. 시험 표준 제정 현황


8. 표준의 이력 정보

8.1. 표준의 이력

판수 제/개정일 제․개정내역

제 1 판 2013.xx.xx 제정

TTAE.3G-SAT.36.212

8.2. 주요 개정 사항



iv TTAE.3G-SAT.36.212

Preface

1. Purpose of Technical Specification

This technical specification defines the technology related to the physical layer of

the system based on Orthogonal Frequency Division Multiplexing (OFDM) as satellite

IMT-Advanced radio interface. It has been developed based on the technical

specification of 3GPP LTE and LTE-Advanced FDD.

2. Summary of Contents

Several transport channels can be multiplexed and transmitted onto one physical

channel. TTAE.3G-SAT.36.212 is addressed the procedure (CRC, Coding, Rate

matching, insertion of DTX, Interleaving, Multiplexing and so on) until transport

channels is mapped onto physical channels in SAT-OFDM system with compatibility to

3GPP LTE and LTE-Advanced FDD as satellite IMT-Advanced.

3. Applicable Fields of Industry and its Effect

TTAE.3G-SAT.36.212 defines the procedure for realization of transport channels

onto physical channels. The unified standard for multiplexing and coding can guarantee

the compatibility between terminal and base stations or other types of equipments.

This technical specification is possible to apply to the 4G personal mobile satellite

communication which can provide the seamless service using satellites.

4. Reference Standards(Recommendations)

4.1. International Standards(Recommendations)

- LTE TS 36.212 – Physical Layer – Multiplexing and channel coding (Release 8)

(v.8.8.0)


v TTAE.3G-SAT.36.212

4.2. Domestic Standards

- TTAT.3G-36.212 – Physical Layer – Multiplexing and channel coding (Release 8)

(v.8.3.0)

5. Relationship to Reference Standards(Recommendations)

5.1. Relationship of Reference Standards

Technical specification LTE TS 36.212 has represented multiplexing and channel

coding for the physical layer of 3GPP LTE and LTE-Advanced as terrestrial IMT system.

The contents of this technical specification are same as those of 3GPP LTE FDD

except those of the parts in which SAT-OFDMA has no commonality with 3GPP LTE

FDD.

5.2. Differences between Reference Standard(Recommendation) and this Standard

TTAE.3G-SAT.36.212 LTE TS 36.212 비고

1. Scope 1. Scope Modified

2. Reference 2. Reference Modified

3. Definitions, symbols and

abbreviations

3. Definitions, symbols and

abbreviations

Modified

4. Mapping to physical

channels

4. Mapping to physical

channels

Same

5. Channel coding,

multiplexing and interleaving

5. Channel coding,

multiplexing and interleaving

Modified

6. Statement of Intellectual Property Rights

IPRs related to the present document may have been declared to TTA. The

information pertaining to these IPRs, if any, is available on the TTA Website.

No guarantee can be given as to the existence of other IPRs not referenced on the

TTA website.

And, please make sure to check before applying the standard.


vi TTAE.3G-SAT.36.212

7. Statement of Testing and Certification

7.1. Object of Testing and Certification

- None

7.2. Standards of Testing and Certification

- None

8. History of Technical Specification

8.1. Change History

Edition Issued date Contents

The 1st edition 2013.xx.xx Established

TTAE.3G-SAT.36.212

8.2. Revisions

- None


vii TTAE.3G-SAT.36.212

목 차

1 장. 표준의 범위 ········································································ 6

2 장. 참조표준 ············································································ 6

3 장. 정의 및 약어 ······································································· 6

4 장. 물리 채널과의 매핑 ······························································· 7

5 장. 채널코딩, 멀티플렉싱 및 인터리빙 ·············································· 7

부속서 A. 변경 이력 ···································································· 14


viii TTAE.3G-SAT.36.212

Contents

Section 1. Scope ······································································· 6

Section 2. Reference ··································································· 6

Section 3. Definitions, symbols and abbreviations ································ 6

Section 4. Mapping to physical channels ··········································· 7

Section 5. Channel coding, multiplexing and interleaving ······················· 7

Annex A. Change history ····························································· 14

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) Technical Specification

Telecommunications Technology Association (TTA); Mobile Communication Technical Committee;

SAT-OFDM; Physical Channels and Modulation


.

TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 2

Keywords

SAT-OFDM, radio, layer 1

Copyright Notification

TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 3

Contents

Foreword............................................................................................................................................................. 4

Introduction ........................................................................................................................................................ 4

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

3 Definitions, symbols and abbreviations ................................................................................................... 6 3.1 Definitions ......................................................................................................................................................... 6 3.2 Symbols ............................................................................................................................................................. 6 3.3 Abbreviations ..................................................................................................................................................... 6

4 Mapping to physical channels .................................................................................................................. 7

5 Channel coding, multiplexing and interleaving ....................................................................................... 7 5.1 Generic procedures ............................................................................................................................................ 7 5.2 Uplink transport channels and control information ........................................................................................... 7 5.2.1 Random access channel ................................................................................................................................ 7 5.2.2 Uplink shared channel .................................................................................................................................. 7 5.2.2.1 Transport block CRC attachment ........................................................................................................... 7 5.2.2.2 Code block segmentation and code block CRC attachment ................................................................... 7 5.2.2.3 Channel coding of UL-SCH ................................................................................................................... 7 5.2.2.4 Rate matching ......................................................................................................................................... 7 5.2.2.5 Code block concatenation ....................................................................................................................... 8 5.2.2.6 Channel coding of control information ................................................................................................... 8 5.2.2.6.1 Channel quality information formats for wideband CQI reports ...................................................... 8 5.2.2.6.2 Channel quality information formats for higher layer configured subband CQI reports .................. 8 5.2.2.6.3 Channel quality information formats for UE selected subband CQI reports .................................... 8 5.2.2.6.4 Channel coding for CQI/PMI information in PUSCH ...................................................................... 8 5.2.2.7 Data and control multiplexing ................................................................................................................ 8 5.2.2.8 Channel interleaver ................................................................................................................................. 8 5.2.3 Uplink control information on PUCCH ....................................................................................................... 8 5.2.3.1 Channel coding for UCI HARQ-ACK ................................................................................................... 9 5.2.3.2 Channel coding for UCI scheduling request ........................................................................................... 9 5.2.3.3 Channel coding for UCI channel quality information ............................................................................ 9 5.2.3.3.1 Channel quality information formats for wideband reports .............................................................. 9 5.2.3.3.2 Channel quality information formats for UE-selected sub-band reports ........................................... 9 5.2.3.4 Channel coding for UCI channel quality information and HARQ-ACK .............................................. 10 5.2.4 Uplink control information on PUSCH without UL-SCH data .................................................................. 10 5.3 Downlink transport channels and control information ..................................................................................... 10 5.3.1 Broadcast channel ...................................................................................................................................... 10 5.3.2 Downlink shared channel, Paging channel and Multicast channel ............................................................. 10 5.3.3 Downlink control information .................................................................................................................... 10 5.3.3.1 DCI formats .......................................................................................................................................... 10 5.3.3.1.1 Format 0 .......................................................................................................................................... 10 5.3.3.1.2 Format 1 .......................................................................................................................................... 10 5.3.3.1.3 Format 1A ....................................................................................................................................... 11 5.3.3.1.3A Format 1B ....................................................................................................................................... 11 5.3.3.1.4 Format 1C ....................................................................................................................................... 11 5.3.3.1.4A Format 1D ....................................................................................................................................... 11 5.3.3.1.5 Format 2 .......................................................................................................................................... 12 5.3.3.1.5A Format 2A ....................................................................................................................................... 12 5.3.3.1.5B Format 2B ....................................................................................................................................... 12 5.3.3.2 CRC attachment .................................................................................................................................... 13 5.3.3.3 Channel coding ..................................................................................................................................... 13 5.3.3.4 Rate matching ....................................................................................................................................... 13 5.3.4 Control format indicator ............................................................................................................................. 13 5.3.5 HARQ indicator (HI) ................................................................................................................................. 13

Annex A (informative): Change history ............................................................................................... 14

TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 4

Foreword

This Technical Specification has been produced by the TTA.

The contents of the present document are subject to continuing work within the TTA and may change following formal

TTA approval. Should the TTA modify the contents of the present document, it will be re-released by the TTA with an

identifying change of release date and an increase in version number as follows:

Version x.y.z

where:

x the first digit:

1 presented to TTA for information;

2 presented to TTA for approval;

3 or greater indicates TTA approved document under change control.

y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates,

etc.

z the third digit is incremented when editorial only changes have been incorporated in the document.

Introduction

The SAT-OFDM is a satellite radio interface to deliver various advanced mobile telecommunication services utilizing

either GEO (geostationary earth orbit) or LEO (low earth orbit) or MEO (Medium earth orbit) satellite(s). The radio

interface has a high degree of commonality with terrestrial 3GPP LTE specifications, but it also has a number of

different features. Those features, which are necessary to reflect the satellite-specific characteristics such as long round

trip delay and slow fading satellite channel, are implemented in the form of random access, interleaving, closed loop

power control and so on. In this regards, SAT-OFDM has two operational modes which are normal mode and

enhancing mode. The normal mode will address UE fully compatible with 3GPP LTE, with adaptation for agility for a

neighbouring MSS frequency band. On the other hands, the enhancing mode provide performance enhancement by

incorporating additional satellite specific features.

NOTE: The LTE(-Advanced) standards documents referenced in SAT-OFDM specifications are the transposed

documents provided by TTA which is one of the identified Transposing Organizations of 3GPP LTE(-Advanced)

specifications in ITU-R Recommendation M.2012. The detailed transposing relationship between TTA transposed

LTE(-Advanced) documents and 3GPP LTE(-Advanced) documents is shown in ITU-R Recommendation M.2012.

Due to the differences between terrestrial and satellite channel characteristics, some modifications to the LTE standards

are necessary. Some specifications are directly applicable, whereas others are applicable with modifications. Similarly,

some LTE standards do not apply, whilst some SAT-OFDM specifications have no corresponding LTE specifications.

Since SAT-OFDM is derived from 3GPP LTE(-Advanced), the organization of the SAT-OFDM specifications closely

follows the original 3GPP structure. The SAT-OFDM numbers have been designed to follow the corresponding 3GPP

LTE numbering system. All SAT-OFDM specifications have the following numbering system.

TTAE.3G-SAT. xx.yyy

Where:

The numbers xx and yyy correspond to the 3GPP-numbering scheme.

A SAT-OFDM system is defined by the combination of a family of SAT-OFDM specifications and 3GPP specifications,

as follows:

If a SAT-OFDM specification exists it takes precedence over the corresponding 3GPP specification (if any).

This precedence rule applies to any references in the corresponding 3GPP specifications.

TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 5

If a SAT-OFDM specification does not exist, the corresponding 3GPP specification may or may not apply. The

exact applicability of the complete list of 3GPP specifications shall be defined at a later stage.

The following terminology translations are made between terminologies used in SAT-OFDM and corresponding LTE(-

Advanced) specifications.

SAT-OFDM LTE(-Advanced)

S-RA E-UTRA

S-RAN E-UTRAN

S-eNodeB eNodeB

Beam Cell

IBIC ICIC

The specifications for the normal mode operation of SAT-OFDM is based on the 3GPP LTE(-Advanced) eUTRA FDD

radio interface already standardized in 3GPP. Mobile satellite systems intending to use this mode will address user

equipment fully compatible with 3GPP LTE(-Advanced) eUTRA FDD WCDMA, with agility for the Mobile Satellite

Service (MSS) band.

The specifications for the enhancing mode operation of SAT-OFDM is based on the adaptation to the satellite

environment of terrestrial LTE(-Advanced) for performance enhancement by incorporating additional satellite specific

features.

TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 6

1 Scope

The present document specifies the coding, multiplexing and mapping to physical channels for SAT-OFDM.

2 References

The following documents contain provisions which, through reference in this text, constitute provisions of the present

document.

References are either specific (identified by date of publication, edition number, version number, etc.) or

non-specific.

For a specific reference, subsequent revisions do not apply.

For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including

a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same

Release as the present document.

[1] 3GPP TR 21.905: "Vocabulary for 3GPP Specifications".

[2] TTAE.3G-SAT.36.211: " SAT-OFDM; Physical channels and modulation".

[3] TTAE.3G-SAT.36.213: " SAT-OFDM; Physical layer procedures".

[4] TTAT.3G-36.306(R8-8.3.0): "Evolved Universal Terrestrial Radio Access (E-UTRA); User

Equipment (UE) radio access.

[5] TTAT.3G-36.321(R8-8.3.0): “Evolved Universal Terrestrial Radio Access (E-UTRA); Medium

Access Control (MAC) protocol specification”

[6] TTAT.3G-36.212(R8-8.6.0): “Evolved Universal Terrestrial Radio Access (E-UTRA);

Multiplexing and channel coding”

3 Definitions, symbols and abbreviations

3.1 Definitions

Definitions used in the present document are same as clause 3.1 of TTAT.3G-36.212[6].

3.2 Symbols

Symbols used in the present document are same as clause 3.1 of TTAT.3G-36.212[6].

3.3 Abbreviations

For the purposes of the present document, the following abbreviations apply:

GEO Geostationary Earth Orbit

MEO Medium Earth Orbit

LEO Low Earth Orbit

RM Receiver Memory

TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 7

Other abbreviations used in the present document are same as clause 3.2 of TTAT.3G-36.212[6].

4 Mapping to physical channels

The contents in this clause are normatively referenced by Clause 4 of TTAT.3G-36.212[6].

5 Channel coding, multiplexing and interleaving

The contents in this clause are normatively referenced by Clause 5 of TTAT.3G-36.212[6].

5.1 Generic procedures

The contents in this clause are normatively referenced by Clause 5.1 of TTAT.3G-36.212[6].

5.2 Uplink transport channels and control information

5.2.1 Random access channel

The contents in this clause are normatively referenced by Clause 5.2.1 of TTAT.3G-36.212[6].

5.2.2 Uplink shared channel


In addition, in order to adapt satellite specific conditions or performance enhancement in the satellite system, it is

specified that TDD related operation is not considered.

5.2.2.1 Transport block CRC attachment

The contents in this clause are normatively referenced by Clause 5.2.2.1 of TTAT.3G-36.212[6].



5.2.2.2 Code block segmentation and code block CRC attachment


5.2.2.3 Channel coding of UL-SCH


5.2.2.4 Rate matching


TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 8

5.2.2.5 Code block concatenation


5.2.2.6 Channel coding of control information


5.2.2.6.1 Channel quality information formats for wideband CQI reports

In normal mode, the contents in this clause are normatively referenced by Clause 5.2.2.6.1 of TTAT.3G-36.212[6].

In addition, the followings are specified in order to adapt satellite specific conditions or performance enhancement in

the satellite system.

In enhancing mode, 5 bits of Wide-band CQI is defined as shown in Table 5.2.2.6.1-1A.

Table 5.2.2.6.1-1A: new Fields on enhancing mode for channel quality information feedback for wideband CQI reports (transmission mode 4, transmission mode 6 and transmission mode 8

configured with PMI/RI reporting).

Field Bit width

2 antenna ports 4 antenna ports

Rank = 1 Rank = 2 Rank = 1 Rank > 1

Wideband CQI codeword 0 5 5 5 5

Wideband CQI codeword 1 0 5 0 5

5.2.2.6.2 Channel quality information formats for higher layer configured subband CQI reports

The contents in this clause are normatively referenced by Clause 5.2.2.6.2 of TTAT.3G-36.212[6].

5.2.2.6.3 Channel quality information formats for UE selected subband CQI reports


5.2.2.6.4 Channel coding for CQI/PMI information in PUSCH


5.2.2.7 Data and control multiplexing


5.2.2.8 Channel interleaver


5.2.3 Uplink control information on PUCCH


TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 9

5.2.3.1 Channel coding for UCI HARQ-ACK




In enhancing mode, the receiver memory (RM) field is added to HARQ-ACK. The interpretation of the RM field is

provided in Table 5.2.3.1-1.

Table 5.2.3.1-1: RM field interpretation

Value Description

00 Receiver memory is enough to store new erroneous packet

01 Receiver memory is not enough to store new erroneous packet.

10 The packet indicated by feedback information was not stored in

receiver memory.

11 The packet indicated by feedback information should be

retransmitted in the first piece of encoding packet.

5.2.3.2 Channel coding for UCI scheduling request


5.2.3.3 Channel coding for UCI channel quality information


5.2.3.3.1 Channel quality information formats for wideband reports

In normal mode, the contents in this clause are normatively referenced by Clause 5.2.3.3.1 of TTAT.3G-36.212[6].



In enhancing mode, 5 bits of Wide-band CQI is defined as shown in Table 5.2.3.3.1-1A and Table 5.2.3.3.1-2B.

Table 5.2.3.3.1-1A: new UCI fields of enhancing mode for channel quality information feedback for wideband CQI reports (transmission mode 1, transmission mode 2, transmission mode 3,

transmission mode 7 and transmission mode 8 configured without PMI/RI reporting).

Field Bit width

Wide-band CQI 5

Table 5.2.3.3.1-2B: new UCI fields of enhancing mode for channel quality information feedback for

wideband CQI reports (transmission mode 4, transmission mode 5, transmission mode 6 and transmission mode 8 configured with PMI/RI reporting).

Field

Bit width

2 antenna ports 4 antenna ports

Rank = 1 Rank = 2 Rank = 1 Rank > 1

Wide-band CQI 5 5 5 5

5.2.3.3.2 Channel quality information formats for UE-selected sub-band reports


TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 10

5.2.3.4 Channel coding for UCI channel quality information


5.2.4 Uplink control information on PUSCH without UL-SCH data

The contents in this clause are normatively referenced by Clause 5.2. 4 of TTAT.3G-36.212[6].



5.3 Downlink transport channels and control information

5.3.1 Broadcast channel


5.3.2 Downlink shared channel, Paging channel and Multicast channel


5.3.3 Downlink control information


5.3.3.1 DCI formats


5.3.3.1.1 Format 0




TDD related operation is not considered.

In enhancing mode, the following information which is transmitted by means of the DCI format 0 for satellite carrier

aggregation is modified to:

- New data indicator – 2 bit.

5.3.3.1.2 Format 1




TDD related operation is not considered

TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 11

In enhancing mode, the following information which is transmitted by means of the DCI format 1 for satellite carrier

aggregation is modified to:


- HARQ process number – 9 bits

- New data indicator – 2 bit

5.3.3.1.3 Format 1A





In enhancing mode, the following information which is transmitted by means of the DCI format 1A for satellite HARQ

and satellite carrier aggregation is modified to:



5.3.3.1.3A Format 1B

The contents in this clause are normatively referenced by Clause 5.3.3.1.3A of TTAT.3G-36.212[6].




In enhancing mode, the following information which is transmitted by means of the DCI format 1B for satellite HARQ




5.3.3.1.4 Format 1C

The contents in this clause are normatively referenced by Clause 5.3.3.1.4 of TTAT.3G-36.212[6]

5.3.3.1.4A Format 1D





In enhancing mode, the following information which is transmitted by means of the DCI format 1D for satellite HARQ




TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 12

5.3.3.1.5 Format 2





In enhancing mode, the following information which is transmitted by means of the DCI format 2 for satellite HARQ



In addition, for transport block 1:




5.3.3.1.5A Format 2A





In enhancing mode the following information which is transmitted by means of the DCI format 2A for satellite HARQ







5.3.3.1.5B Format 2B

The contents in this clause are normatively referenced by Clause 5.3.3.1.5B of TTAT.3G-36.212[6].




In enhancing mode the following information which is transmitted by means of the DCI format 5B for satellite HARQ






TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 13


5.3.3.2 CRC attachment

The contents in this clause are normatively referenced by Clause 5.3.3.2 of TTAT.3G-36.212[6]

5.3.3.3 Channel coding


5.3.3.4 Rate matching


5.3.4 Control format indicator

The contents in this clause are normatively referenced by Clause 5.3.4 of TTAT.3G-36.212[6]

5.3.5 HARQ indicator (HI)

The contents in this clause are normatively referenced by Clause 5.3.5 of TTAT.3G-36.212[6]

TTA

TTAE.3G-SAT.36.212 V1.0.0 (2013-xx) 14

Annex A (informative): Change history

Change history

Date WG Input doc.. Subject/Comment Old New

2013/xx PG701 TTAT.3G 36.212 Adaptation from LTE TS 36.212 v.8.3.0 - 1.0.0


15 TTAE.3G-SAT.36.212

영문 표준 해설서

1 장. 표준의 범위

본 표준의 구성 및 범위를 정의한다.

2 장. 참고 문헌

본 표준에서 인용한 문서를 제시한다.

3 장. 용어 정의 및 약어

본 표준에서 사용된 용어를 정의하고 약어를 정리한다.

4 장. 물리채널로 매핑

SAT-OFDM 무선인터페이스의 전달채널과 물리채널간의 매핑 관계를 정의한다.

5 장. 채널 부호화, 다중화 및 인터리빙

SAT-OFDM 무선인터페이스의 전송 채널이 물리 채널에 매핑 될 때까지의 각 과정 (CRC,

Coding, Rate matching, insertion of DTX, Interleaving, Multiplexing 등) 들에 대해 정의한다.

부록 1. 문서 수정 이력

본 표준의 내용 수정 이력을 기록한다.


16 TTAE.3G-SAT.36.212

표준 작성 공헌자

표준 번호 : TTAE.3G-SAT.36.212

이 표준의 제정개정 및 발간을 위해 아래와 같이 여러분들이 공헌하였습니다.

구분 성명 위원회 및 직위 연락처 소속사

표준(과제) 제안 김희욱 PG701/위원 042-860-5422

[email protected]

한국전자통신

연구원

표준 초안

작성자 김희욱 PG701/위원

042-860-5422

[email protected]

한국전자통신

연구원

표준 초안

에디터 김희욱 PG701/위원

042-860-5422

[email protected]

한국전자통신

연구원

표준 초안 검토

이현우 PG701 의장 [email protected] 단국대

외 프로젝트그룹 위원

표준안 심의

오민석 이동통신기술위원회 의장 031-450-2916

[email protected] LG 전자

외 기술위원회 위원

사무국 담당

오충근 표준화본부 전파방송부

선임

031-724-0094

[email protected] TTA

이혜영 표준화본부 전파방송부

선임

031-724-00


김대중 표준화본부 전파방송부

부장

031-724-0090


mailto:[email protected]







IMT-Advanced SAT-OFDM – 다중화 및 채널 부호화

IMT- Advanced SAT-OFDM - Multiplexing and channel coding


발행인 : 한국정보통신기술협회 회장

발행처 : 한국정보통신기술협회

463-824, 경기도 성남시 분당구 분당로 47

Tel : 031-724-0114, Fax : 031-724-0109

발행일 : 2013. 00.

3gpp ts 36.212, 'multiplexing and channel coding'...the sat-ofdm is a satellite radio...

Documents