c_cc94_tm_11_0704_01
TRANSCRIPT
CC 94rapid blue (BE)Accelerator for reinforced concrete and cement mortar
CHARACTERISTICS� chloride-free� powder form� accelerates setting
Tested at the German Institute ofConstruction Engineering, BerlinTest certificate no. Z-PA VII-5a/104
SCOPE OF USEFor cement mortar, concrete and reinforcedconcrete.In building construction and civil engineering.For indoor, outdoor and underwater work.For urgent, rapid repair work.Not suitable for fair-faced concrete or externalrenderings.
APPLICATIONSprinkle an appropriate quantity of CC 94directly onto the mixture in the mortar bucket ormixer and mix thoroughly again. Before usingCC 94 as a concrete additive, it is necessary tocarry out a suitability test acc. to DIN 1045.
PLEASE NOTEUse CC 94 only at temperatures of -10 °C to+25 °C. All data given was obtained at a temperature of+23 °C and 50 % relative air humidity, using aPortland cement of strength class 32.5 R. Ifother standard cements are used, allowancemust be made for the changed technical data.
CER
ESIT
C_C
C94
_TM
_11_
0704
1
The higher CC 94 is dosed and the higher thecement factor in the concrete or mortar, thefaster the concrete or mortar will begin to setand harden.Protect skin and eyes when using CC 94 andcement-containing materials. If contact occurs, rinse thoroughly with water. In case of contact with the eyes obtain medicaladvice.Please refer in particular to DIN 1045.
Should you need support or advice, please consultour advisory service for architects and craftsmen onthe hotline numbers Phone: +49 211 797 0Fax: +49 211 798 2148
BAUTECHNIK
TECHNICAL DATABase: Special mixture of modified
electrolytes GISCODE BZM 2
Density: approx. 0.88 kg/l
Reference values for use:Mixing Dosage Initialratio (related to setting
cement weight)
Concreteacc. to 0.2 % approx. 60 mins
DIN 1045 max. 0.5 % approx. 20 mins
CementMortar 1 : 1 1.0 % approx. 5 mins
1 : 2 1.0 % approx. 12 mins
1 : 3 1.0 % approx. 21 mins
1 : 4 1.0 % approx. 30 mins
When added to cement mortar, CC 94 can also be dosedhigher for more rapid setting and hardening. Carry out apreliminary test!
Storage: shelf life approx. 12 months in adry place
Packaging: 4 kg and 13 kg plastic buckets
CER
ESIT
C_C
C94
_TM
_11_
0704
2
Build on professional solutions.
Henkel AG & Co. KGaA – BautechnikHenkelstraße 67 · D-40589 DüsseldorfTelefon +49 (0) 211/797-0 • Telefax +49 (0) 211/798 6667Internet: www.ceresit.henkel.com · E-Mail: [email protected]
The information contained herein, particularly recommendations for the handling and use of our products, is based on our professional experience.As materials and conditions may vary with each intended application, and thus are beyond our sphere of influence, we strongly recommend thatin each case sufficient tests are conducted to check the suitability of our products for their intended use. Legal liability cannot be accepted on thebasis of the contents of this data sheet or any verbal advice given, unless there is a case of wilful misconduct or gross negligence on our part.This technical data sheet supersedes all previous editions relevant to this product.
Apart from the information given here it is also important to observe the relevant guidelines and regulations of various organisations and tradeassociations as well as the respective standards of the German Standards Institute (DIN). The aforementioned characteristics are based on practicalexperience and applied testing. Warranted properties and possible uses which go beyond those warranted in this information sheet require ourwritten confirmation. All data given was obtained at an ambient and material temperature of +23 °C and 50 % relative air humidity unless specifiedotherwise. Please note that under other climatic conditions hardening can be accelerated or delayed.