愛得電子股份有限公司 匣式電容系列規格書 -...
TRANSCRIPT
愛得電子股份有限公司 匣式電容系列規格書
成品型號成品型號成品型號成品型號:MEX104K2FCA
MEX224K2FCA MEX224K2FDA 版次版次版次版次::::0 日期日期日期日期::::2013/01/30 頁次頁次頁次頁次: 1 of 7
AID ELECTRONICS CORPORATION
制制制制 訂訂訂訂 者者者者 版本版本版本版本 制訂日期制訂日期制訂日期制訂日期 修修修修 訂訂訂訂 說說說說 明明明明
郭秀真 0 2012/08/17
首次發行
Adobe Acrobat
Document
”ROHS”
Adobe Acrobat
Document
”CUL”
Adobe Acrobat
Document
”VDE/ENEC”
核核核核 准准准准 審審審審 核核核核 制制制制 訂訂訂訂
陳
勝
傑
蔡
坤
旺
郭
秀
真
愛得電子股份有限公司 匣式電容系列規格書
成品型號成品型號成品型號成品型號:MEX104K2FCA
MEX224K2FCA MEX224K2FDA 版次版次版次版次::::0 日期日期日期日期::::2013/01/30 頁次頁次頁次頁次: 2 of 7
AID ELECTRONICS CORPORATION
Metallized Film Capacitor. TYPE:MEX104K/300VAC MEX 224K300VAC
TYPE MEX
DIMENSIONS Unit mm
CAPACITANCE µF 0.1、0.22
Max. Voltage VAC 300
Max. Insulation Resistance IR
Cap≦0.33uF IR>30,000MOHM
Cap>0.33uF IR>10,000MOHM×uF
AID ELECTRONICS CORPORATION NO.65, LANE 667,CHANG SAN ROAD,SHENG KUNG,TAICHCING,TAIWAN,R.O.C TEL:886-4-25620100 FAX:886-4-25629657
http://www.aid.com.tw/ E-Mail:[email protected]
愛得電子股份有限公司 匣式電容系列規格書
成品型號成品型號成品型號成品型號:MEX104K2FCA
MEX224K2FCA MEX224K2FDA 版次版次版次版次::::0 日期日期日期日期::::2013/01/30 頁次頁次頁次頁次: 3 of 7
AID ELECTRONICS CORPORATION
1. Part name:::
:Metallized Film Capacitor.
2. Type:::
:MEX(Plastic Case ,Radial leads).
3. Working Voltage:::
:300(2F)VAC
4. Capacitance Range:::
:0.1uF、、、
、0.22uF
5. Capacitance Tolerance:::
:K (±10%)
6. Temperature Range:﹣:﹣:﹣
:﹣40
--+100
7.Flame retardant plastic case & the Flame retardant resin:::
:PBT 94-V0
8. Characteristics
ARTICLE APPLICATION ITEM CHARACTERSTICS TEST METHOD
1. Dielectric Strength (Between Terminals)
No damage R.V.×430%VDC For 2 Sec 25
2. Insulation Resistance (Between Terminals)
≦Cap 0.33uF IR>30,000MOHM Cap>0.33uF IR>10,000MOHM×uF
Measured at 100VDC after 1 minute.
3. Capacitance Within the specification
4. Dissipation factor tan δ<0.1%
Measured with frequency 10Khz and AC voltage less than 6V.
Pull strength
Wire diameter:0.6~0.8mm
Load:1Kg,time:10Sec
5. Tensile strength
Bending strength
No damage
Wire diameter:0.6~0.8mm
Load:0.5Kg,90°×2~5times
6. Vibration proof No opening and short happened No damage in element junction and appearance.
10 - 55Hz 1.5 mm amplitude3 direction 2H Per direction.
7. Solder ability Good tinning, by eye measurement more than 3/4 of circumference is covered with new solder
Solder temp. 245 ±5 dwell time 2.5± 0.5 Sec
8. Cold resistance
Capacitance Variation
Within ∆C/C±5.0% of the
value before test
Temp: - 40+8 -0
Duration:2+1/-0 hours
Then recover at ordinary Condition at least 2 hours
Insulation resistance
≧ ≦15000 MΩ for C 0.33uF
≧5000 MΩ for C>0.33uF
9. Heat
Capacitance Variation
within +5 -0% of the value before test
Temp:100±2
Duration:16+1/-0 hours
Then recover at ordinary Condition at least 2 hours
愛得電子股份有限公司 匣式電容系列規格書
成品型號成品型號成品型號成品型號:MEX104K2FCA
MEX224K2FCA MEX224K2FDA 版次版次版次版次::::0 日期日期日期日期::::2013/01/30 頁次頁次頁次頁次: 4 of 7
AID ELECTRONICS CORPORATION
ARTICLE APPLICATION ITEM CHARACTERSTICS TEST METHOD
Appearance No abnormality
Withstand Voltage
Test as NO:no permanent
Breakdown or flash – over is permitted
Capacitance Variation
≦Within∆C/C ±10% of the Value before test
Insulation Resistance
≧ ≦7500MΩ for C 0.33uF
≧2500MΩ×uF for C>0.33uF
10. Humidity life test
Dissipation Factor
≦ ≦∆DF 0.8%(C 1uF f=10Khz) ≦ ≦∆DF 0.5%(C 1uF f=1Khz)
Humidity of 90~95% RH Temp:40±2
Duration:8 hours Then
recover at ordinary
condition at least 16
hours for five circles.
According IEC60384-14
Appearance No abnormality Marking to be legible
Withstand Voltage
Test as NO1:no permanent
Breakdown or flash – over is permitted
Capacitance Variation
≦Within∆C/C ±10% of the Value before test
Insulation Resistance
≧ ≦15000MΩ for C 0.33uF
≧5000MΩ×uF for C>0.33uF
11. Heat life test
Dissipation Factor
≦ ≦∆DF 0.8%(C 1uF f=10Khz) ≦ ≦∆DF 0.5%(C 1uF f=1Khz)
Temp:Rate Temp.±2
Duration : 1000+48/-0
hours for continues test
Applied voltage:
125% of R.V(50/60Hz)
According IEC60384-14
Temp:Rate Temp.±2
Duration:ON/OFF /2sec.
for the one hundred
thousand times.
Applied voltage:
140% of R.V(50/60Hz)
According CNS4327
C7028
8. MARKING a. w.v. b. Capacitance c. Capacitance tolerance d. Trading mark 9.Terminal configuration & Dimension
CAPACITANCE DIMENSION(Tolerance+-1.0mm)
PART NO. VOLTAGE SYMBOL MF L H T P d
MEX104K2FCA 300VAC 104 0.1 13.0 12.0 6.0 10.0 0.6
MEX224K2FCA 300VAC 224 0.22 13.0 12.0 6.5 10.0 0.6
愛得電子股份有限公司 匣式電容系列規格書
成品型號成品型號成品型號成品型號:MEX104K2FCA
MEX224K2FCA MEX224K2FDA 版次版次版次版次::::0 日期日期日期日期::::2013/01/30 頁次頁次頁次頁次: 5 of 7
AID ELECTRONICS CORPORATION
MEX224K2FDA 300VAC 224 0.22 18.0 14.5 8.5 15.0 0.8
TEMPERATURE AND FREQUENCY CHARACTERISTICS
愛得電子股份有限公司 匣式電容系列規格書
成品型號成品型號成品型號成品型號:MEX104K2FCA
MEX224K2FCA MEX224K2FDA 版次版次版次版次::::0 日期日期日期日期::::2013/01/30 頁次頁次頁次頁次: 6 of 7
AID ELECTRONICS CORPORATION
UL Online Certifications Directory OCD Home Quick Guide Contact Us UL.com
QMFZ2.E154421 Plastics - Component
Additional information regarding this certification can be found in UL's iQ Family of Databases (www.ul.com/iq).
NEW -- for additional information concerning the individual material, click on the material designation.
Page Bottom
Plastics - Component
See General Information for Plastics - Component
KO HO CHEMICAL CO LTD E154421
13 ERH KAN RD
SAN KAN HSIANG WAI PU
TAI CHUNG, 438 TAIWAN
H D
Min. H H R T I V 4 C
Thk Flame W A Elec Mech T 9 T
Material Dsg Color mm Class I I Imp Str R 5 I
Epoxy Potting Compound (EP - Potting), "Epoxy Resin", furnished as two liquid components.
9824(#) A/B ALL 0.78 V-0 - - 90 90 90
(#) - May be replaced with two alphanumericc characters designating color.
Marking: Company name and material designation on container, wrapper or finished part.
Last Updated on 2008-08-26
愛得電子股份有限公司 匣式電容系列規格書
成品型號成品型號成品型號成品型號:MEX104K2FCA
MEX224K2FCA MEX224K2FDA 版次版次版次版次::::0 日期日期日期日期::::2013/01/30 頁次頁次頁次頁次: 7 of 7
AID ELECTRONICS CORPORATION
Plastics - Component
Guide Information
NAN YA PLASTICS CORP E130155
PLASTICS 4TH DIV
3RD FL
201 TUNG HWA NORTH RD
TAIPEI, TAIWAN
H D
Min. H H R T I V 4 C
Thk Flame W A Elec Mech T 9 T
Material Dsg Color mm Class I I Imp Str R 5 I
Polybutylene Terephthalate (PBT), furnished as pellets.
1100F, 1101FA, 1101FB, 1110F, 1111FA, 1111FB
1403G3 ALL 0.75 V-0 4 0 130 130 140 — — —
(a)-May be followed by a number or letter indicating glass fiber content 5-30%.
(b)-May be followed by a number or letter indicating glass fiber content 15-30%.
(c)-May be followed by a letter indicating glass fiber content 1-45%.
(d)-May be followed by a letter indicating glass fiber content 1-25%.
(e)-May be followed by a letter indicating glass fiber content 1-30%.
(f1)-Suitable for outdoor use with respect to exposure to Ultraviolet Light, Water Exposure and Immersion in accordance with UL 746C.
(g)-May be followed by a letter indicating glass fiber content 15-45%.
(h)-May be followed by a letter indicating glass fiber content 1-50% Marking: Company name and material designation on container, wrapper or finished part.
QMFZ2.E130155 Plastics - Component