selective coating june 27
TRANSCRIPT
June 2012
Ben-Gurion University of the Negev Faculty of Engineering Sciences
Faculty Unit of Energy Engineering
By: Oleg Shkolnik
Supervisor: Prof. Daniel Feuermann
Photothermal coatings based on functional nanomaterials for the efficient conversion of solar
energy
Supported by: Ministry of Energy and Water Resources
Outline
Theoretical short introduction and motivation
Project description
Review of different types of coatings
Experimental setup and methodology
Current results and future experiments
משטרי מעבר חום -הקדמה
𝑞 בהולכה מעבר חום = −𝐴 ∙ 𝑘∂𝑇∂𝑥
𝑞 חום בהסעה מעבר = 𝐴 ∙ ℎ(𝑇𝑠 − 𝑇∞)
Thermal conductivity of various materials at 0 °C
Material k ( W/ m °C )
Copper 385
Aluminum 202
Carbon steel 1% C 43
Glass wool 0.0038
Air 0.024
מעבר חום בקרינה
𝜀 𝜆 = 𝛼 𝜆 according to Kirchhoff’s law
𝑞 = 𝜎 ∙ 𝐴1 ∙ 𝜀1(𝑇1 4 − 𝑇2
4 )
𝐸𝑏 = 𝐸𝜆𝑑𝜆 ≡ 𝜎 ∙ 𝑇4∞
0 Boltzmann law
𝛼 + 𝜌 + 𝜏 = 1 according to energy balance
Net heat transfer from surface 𝐴1
What is selective coating
A selective absorber coating or material is a thin layer (of the order of µm) on the surface, or a material which exhibits optical properties that drastically vary from one spectral region to another The solar spectrum and the re-radiated spectrum of the hot absorber are separated at relatively low temperature of the absorber. However, the higher the temperature of the surface the more the absorbed solar radiation and the emitted spectra overlap Selective coating was pioneered by Tabor in 1956 in Israel
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0 1000 2000 3000 4000 5000
effi
cien
cy(%
)
wavelength(nm)
C=100 T=550 C
0.00.10.20.30.40.50.60.70.80.91.0
0 1000 2000 3000 4000 5000
effi
cien
cy(%
)
wavelength(nm)
C=25 T=800 C
0 0
( ) (0.95) (0.07) (0.95) (0.07)cr cr
cr cr
cr sun sun bb bbq C I d C I d I d I d
Evaluation of critical wavelength and efficiency estimation
Selective coating the complete project This work is a part of a collaborative project of developing thin nanocomposite layers for high temperature (above 500 C) The samples are prepared at Hebrew University at chemical department by two groups of researchers (Mandler and Magasi et al.,) The Electro-Dynamic analysis of particles mixture is performed at TAU Electrical Engineering department by Steinberg et al. The optical properties measured at Sede Boqer and TAU ( Feuermann and Kribus et al.,)
`
Goals of the project The global purpose of this research is to construct a spectrally selective
ceramic matrix with embedded nanoparticles for photo thermal conversion, stable at high temperature applications.
Each group has its specific requirements to meet.
Hebrew University group :
Solar absorption at 300-2500 nm range (AM 1.5),
above 95% of the total energy.
Low thermal emittance < 0.1
The coating will be designed for continuous
use at a temp >500 C (in air)
Optical properties of selective coatings
BGU : Detailed measurements of spectral and angular reflectance at ambient
and elevated temperatures
Measurements of solar absorptance at high solar concentration
TAU: Prof. Kribus Group
Measuring the of emissivity
• IR Camera 2–14 μm
• Pyroelectric sensor 0.3–16 μm
Prof. Steiberg group Theoretical calculations based on use
Maxwell equations in order to evaluate the α by knowing the dielectric constant of the absorbing particles
Basics assumptions: Homogeneous distribution particles should be one 0.1-0.2 of
the wavelength Spherical, ellipsoidal, or needle
like particles
Types of absorbers
1. Intrinsic absorbers- e.g., HfC(Hafnium Carbide ): two categories of materials fall into this group : transition metals and semiconductors. Unfortunately most selective metals exhibit the cutting edge, of good absorber to pore emitter too earlier at the solar spectrum and therefore not suitable for solar applications
Carl M. Lampert Solar Enegy materials 1( 1979)
2. Multilayer absorbers (e.g., Al203/Mo/ Al203):
Multilayer thin films are dielectric-metal combinations which act
like a selective filter for energy absorption Particular wavelengths of solar energy are absorbed by multiple
reflections in the dielectric-metal layers Such coatings are commonly produced by sputter deposition
technologies with AR layer on the top
N. Selvakumar, Harish C. Barshilia, Materials & Solar Cells (2011)
3. Optical trapping: it is possible to produce a surface with a such roughness that will absorb the visible part of the solar spectrum by pure geometrical means while being opaque to the infrared spectrum
4. Metal dielectric (cermet): highly absorbing metal dielectric composites consisting of nano or micro scale particles embedded in a dielectric or ceramic matrix
Structure of cermet: thin protective layer to prevent diffusion single layer with uniform particles distribution single layer with graded particles distribution double layer - according to fundamental modeling it has higher photo-thermal
conversion efficiency
Cermet types and structures
Offers high degree of flexibility , solar selectivity can be optimized by proper
choice of coating thickness Particle size- it is possible to shift the absorbing and scattering cutoffs to higher
wavelengths when the particle radius increases Possible to predict optical properties using effective medium theories for example
the optimum pore diameter dp=0.08 μm of nickel pigmented alumina coatings have been determined
Usage at broad range of temperatures In addition solar absorbance can be boosted with a proper choice of substrates and AR layer. After a long research and development in solar materials, the cermet remains one of the best and promising candidates for high temperature application
Advantages of cermets over other candidates for high temperature applications
International Energy Agency (IEA) performance criterion (PC) developed for a flat-plate collector selective absorber testing.
𝑃𝐶 = −∆𝑎𝑠 + 0.25 ∙ ∆𝜀 ≤ 0.05 lifetime of at least 25 years and decrease in the annual solar fraction of 5% Service lifetime testing for this criterion is performed by exposing the absorber coating for 200 h at 250°C If the material survives , it is then exposed for 75 h at 300 °C hand roll followed by 600 h at 40 °C and 95 %relative humidity No similar criterion has been developed for testing the service lifetime of high temperature absorbers for CSP. Degradation of the high temperature absorbers usually causes increasing emittance ; in addition while the emittance of many materials after exposure to high temperature does not return to the original emittance measured ( e.g., paint), for some materials the emittance changes at high temperature and returns to the original value
Long term stability
Different matrices were investigated for CERMET layers, more exactly 2 categories
of matrices (silica and alumina). Both alumina and silica matrices are transparent to IR and are stable at high temperature.
Black coatings were prepared by dispersing black pigment (black 26) in the
different matrices, adding dispersant and additives. The coatings were dried at 750°C during 1 hour under air.
SEM of alumina film with Black 26
First set of experiments: Solar irradiation – one sun Ambient temperature Measurements of 4 samples
θs
θi
wet thickness 40 µm
wet thickness 6 µm
achieve 1000K
experimental setup
4 side faces
of furnace
back face of
furnace Front face Total loss
heat loss by convection 5.7 W 2 W 23.9 W 31.6 W
heat loss by radiation 6.6 W 2.4 W 13.6 W 22.6 W
Results for HU samples
θi
θs
Azimuthal effects inside the “specular region”
rotating the sample to observe any difference
in surface structure θi
θs
Φs The structure of the surface has obviously a strong effect
θi
θs
Φs
rotating the sample to observe any difference
in surface structure
Azimuthal effects outside the “specular region”
θi
θs
polar angle effect around specular direction
B-CZ-10.1A ferro 8µm
0
10
20
30
40
50
60
70
0 10 20 30 40 50 60 70
polar angle θs(deg)
refl
ecta
nce
(%
) θi=30° Φs=0°
θi=45° Φs=0°
here θi=θs
Specular effects in polar direction (θs) at two incidence angles
We simply average the directional reflectance over the wavelengths. This is of course not a correct measure but should give some qualitative indication of a relative ‘specularity’ of the different samples.
all the results on one graph
polar angle effect at θi=30° Φs=0°
0
50
100
150
200
250
0 10 20 30 40 50 60 70
polar angle θs (deg)
refl
ecta
nce
(%)
B-CZ-STS-10.2 4.7µm
B-CZ-STS-10.2A 6µm
B-CZ-10.2B 5.9µm
B-CZ-STS-9.2 2.6µm
B-CZ-10.1 4µm
B-CZ-10.1A 8µm
θi
θs
15°
45°
θs=60°
30°
MS 1.3 (two layers) at elevated temperature of 600K
we had to cut off at 1100nm because thermal radiation was too large at the longer wavelengths.
0
200
400
600
800
1000
1200
1400
1600
1800
900 1000 1100 1200 1300 1400 1500 1600 1700
rel. in
ten
sit
y (
%)
wavelength (nm)
relative intensity from MS13 sample in the dark compared to gray reference under illumination
we get 10 times the intensity from thermal radiation than from light reflected
MS 1.3 at 600°K
•attempt to increase signal to noise ratio by optics • better means of measuring temperature • measurement in the solar furnace (to obtain α directly) and will be closer to realistic conditions.
at high temperatures measurements even a very bright lamp is not sufficient while dealing with very absorbing samples
ultimately will be used in solar furnace
Sample inside solar furnace
The next day photos after heating to max temperature 430 °C
Experimental setup using a PCX Condenser Lens 125mm Diam x 500mm Focal Length
A) we have considered using a lens and the sun
Lens position
Problem: Stability of direct beam solar radiation. Ephemeral nature of solarradiation.
Region that the sensor ‘sees’
Light spot that sensor “sees”
Placing the sample at focal plane
Sample position
What did we achieve? much higher intensity light spot completely in the measured region –
experiments at wide angles Hopefully solved uniformity problem
sample holder
sample holder
Region that the sensor “sees”
Light spot that sensor “sees”
θs
θs
0
5
10
15
20
25
30
35
40
45
400 600 800 1000 1200 1400 1600 1800
refl
ecta
nce
(%)
wavelength(nm)
polar angle effect θi=30° Φs=0° MS-CZ- 17C 8.7µm θs=-10°
θs=0°
θs=10°
θs=20°
θs=30°
θs=40°
θs=50°
θs=60°
θi
θs
0
5
10
15
20
25
30
35
40
-10 0 10 20 30 40 50 60 70
refl
ecta
nce
(%)
polar angle θs (deg)
polar angle effect θi=30° Φs=0°-corrected by solar spectrum 17A÷17F 2.5÷ 15.7µm
17B - 2.5µm
17F - 4.8µm
17A - 5.16µm
17C - 8.7µm
17E - 9.1µm
17D - 15.7µm
sample reflectance in non-
specular region
reflectance in specular
region
weighted average
reflectance over both regions
absorbtance
α(θi=30°)
17A -5.16µm 0.050 0.198 0.053 0.947±0.004
17B-2.5µm 0.067 0.223 0.070 0.930±0.005
17C-8.7µm 0.050 0.161 0.053 0.947±0.004
17D-15.7µm 0.043 0.158 0.045 0.955±0.003
17E-9.1µm 0.043 0.170 0.046 0.954±0.003
17F-4.8µm 0.044 0.183 0.046 0.954±0.003
Acknowledgments
This research is supported by the Ministry of energy and water within the framework of the program of scholarships in the field of renewable energy.
I would like to acknowledge my supervisor Prof. Daniel
Feuermann for invaluable support, guidance and scientific assistance.
Thank you
for your attention